SIST EN 303 722 V1.2.1:2022
(Main)Wideband Data Transmission Systems (WDTS) for Fixed Network Radio Equipment operating in the 57 GHz to 71 GHz band - Harmonised Standard for access to radio spectrum
Wideband Data Transmission Systems (WDTS) for Fixed Network Radio Equipment operating in the 57 GHz to 71 GHz band - Harmonised Standard for access to radio spectrum
The present document specifies technical characteristics and methods of measurements for Wideband Data
Transmission Systems (WDTS) fixed network radio equipment operating in the 57 GHz to 71 GHz band taking into
consideration ERC Recommendation 70-03 [i.3], annex 3 (frequency bands c2 and c3) and Commission Decision
2006/771/EC [i.4] bands 75a and 75b.
This radio equipment is capable of operating in all or any part of the frequency bands given in table 1.
NOTE 1: The technical characteristics of applications using these radio equipment are further described in ETSI
TR 103 583 [i.1].
NOTE 2: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.5] is given in annex A.
Širokopasovni sistemi za prenos podatkov (WDTS) za radijsko opremo fiksnega omrežja, ki delujejo v pasu od 57 GHz do 71 GHz - Harmonizirani standard za dostop do radijskega spektra
Ta dokument določa tehnične značilnosti in metode merjenja za širokopasovne sisteme za prenos podatkov (WDTS) za radijsko opremo fiksnega omrežja, ki delujejo v pasu od 57 GHz do 71 GHz, ob upoštevanju priporočila ERC 70-03 [i.3], dodatek 3 (frekvenčna pasova c2 in c3), in sklepa Komisije 2006/771/ES [i.4] (pasova 75a in 75b).
Ta radijska oprema lahko deluje v vseh delih frekvenčnih pasov iz preglednice 1.
OPOMBA 1: Tehnične lastnosti aplikacij, ki uporabljajo to radijsko opremo, so podrobneje opisane v standardu ETSI TR 103 583 [i.1].
OPOMBA 2: Razmerje med tem dokumentom in bistvenimi zahtevami člena 3.2 Direktive 2014/53/EU [i.5] je podano v dodatku A.
General Information
Buy Standard
Standards Content (Sample)
ETSI EN 303 722 V1.2.1 (2022-03)
HARMONISED EUROPEAN STANDARD
Wideband Data Transmission Systems (WDTS)
for Fixed Network Radio Equipment operating
in the 57 GHz to 71 GHz band;
Harmonised Standard for access to radio spectrum
---------------------- Page: 1 ----------------------
2 ETSI EN 303 722 V1.2.1 (2022-03)
Reference
DEN/BRAN-230025
Keywords
60 GHz, access, broadband, fixed networks, radio,
SRD
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2022.
All rights reserved.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 303 722 V1.2.1 (2022-03)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 Conformance requirements . 10
4.2.1 Spectral power density . 10
4.2.1.0 Applicability. 10
4.2.1.1 Definition . 11
4.2.1.2 Limit . 11
4.2.1.3 Conformance . 11
4.2.2 RF output power . 11
4.2.2.0 Applicability. 11
4.2.2.1 Definition . 11
4.2.2.2 Limit . 11
4.2.2.3 Conformance . 11
4.2.3 Transmitter unwanted emissions in the spurious domain . 12
4.2.3.0 Applicability. 12
4.2.3.1 Definition . 12
4.2.3.2 Limit . 12
4.2.3.3 Conformance . 12
4.2.4 Transmitter out-of-band emissions . 12
4.2.4.0 Applicability. 12
4.2.4.1 Definition . 12
4.2.4.2 Limit . 13
4.2.4.3 Conformance . 13
4.2.5 Adaptivity (medium access protocol) . 13
4.2.5.1 Applicability. 13
4.2.5.2 Definition . 13
4.2.5.3 Limit . 14
4.2.5.3.0 General . 14
4.2.5.3.1 Automatic Transmit Power Control. 14
4.2.5.3.2 Automatic Link Adaptation . 14
4.2.5.4 Conformance . 14
4.2.6 Occupied Channel Bandwidth . 14
4.2.6.1 Applicability. 14
4.2.6.2 Definition . 14
4.2.6.3 Limit . 14
4.2.6.4 Conformance . 14
4.2.7 Receiver unwanted emissions in the spurious domain . 14
4.2.7.0 Applicability. 14
4.2.7.1 Definition . 15
4.2.7.2 Limit . 15
4.2.7.3 Conformance . 15
4.2.8 Receiver Blocking . 15
4.2.8.1 Applicability. 15
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 303 722 V1.2.1 (2022-03)
4.2.8.2 Definition . 15
4.2.8.3 Performance Criteria . 15
4.2.8.4 Limit . 15
4.2.8.5 Conformance . 16
4.2.9 Receiver Sensitivity level . 16
4.2.9.1 Applicability. 16
4.2.9.2 Definition . 16
4.2.9.3 Limit . 16
4.2.9.4 Conformance . 16
5 Testing for compliance with technical requirements . 16
5.1 Environmental conditions for testing . 16
5.1.1 General . 16
5.1.2 Normal test conditions . 16
5.1.2.1 Normal temperature and humidity . 16
5.1.2.2 Normal power source . 17
5.1.3 Extreme test conditions . 17
5.2 Test procedure for the essential radio test suites . 17
5.2.0 General . 17
5.2.1 Product Information . 17
5.2.2 Test modulation, frequency and configuration . 17
5.2.3 Spectral power density . 18
5.2.3.1 Test conditions . 18
5.2.3.2 Test method . 18
5.2.4 RF output power . 19
5.2.4.1 Test conditions . 19
5.2.4.2 Test method . 19
5.2.5 Transmitter unwanted emissions in the spurious domain . 20
5.2.5.0 Test conditions . 20
5.2.5.1 Pre-scan . 20
5.2.5.2 Identified emissions . 21
5.2.6 Transmitter out-of-band emissions . 22
5.2.6.1 Test conditions . 22
5.2.6.2 Test method . 22
5.2.7 Adaptivity (medium access protocol) . 22
5.2.7.1 Test conditions . 22
5.2.7.2 Test method (ATPC) . 22
5.2.7.3 Test method (ALA) . 24
5.2.8 Occupied Channel Bandwidth . 24
5.2.8.1 Test conditions . 24
5.2.8.2 Test method . 25
5.2.9 Receiver unwanted emissions in the spurious domain . 25
5.2.9.0 Test conditions . 25
5.2.9.1 Pre-scan . 26
5.2.9.2 Identified emissions . 26
5.2.10 Receiver Blocking . 26
5.2.10.1 Test conditions . 26
5.2.10.2 Test Method . 27
5.2.11 Receiver sensitivity level . 28
5.2.11.1 Test conditions . 28
5.2.11.2 Test method . 28
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 29
Annex B (informative): Maximum Measurement Uncertainty . 31
Annex C (normative): Test sites and arrangements for radiated measurements . 32
C.1 Test sites . 32
C.1.1 Open air test sites . 32
C.1.2 Anechoic chamber . 33
C.1.2.1 General . 33
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 303 722 V1.2.1 (2022-03)
C.1.2.2 Description . 33
C.1.2.3 Influence of parasitic reflections . 33
C.1.2.4 Calibration and mode of use . 33
C.2 Test antenna . 35
C.3 Substitution antenna . 35
Annex D (normative): General description of measurement . 36
D.1 Radiated measurements . 36
D.2 Substitution measurement . 37
Annex E (informative): Bibliography . 38
Annex F (informative): Change History . 39
History . 40
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 303 722 V1.2.1 (2022-03)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its
Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Broadband Radio Access
Networks (BRAN).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.5].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
National transposition dates
Date of adoption of this EN: 10 March 2022
Date of latest announcement of this EN (doa): 30 June 2022
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 December 2022
Date of withdrawal of any conflicting National Standard (dow): 31 December 2023
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 303 722 V1.2.1 (2022-03)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 303 722 V1.2.1 (2022-03)
1 Scope
The present document specifies technical characteristics and methods of measurements for Wideband Data
Transmission Systems (WDTS) fixed network radio equipment operating in the 57 GHz to 71 GHz band taking into
consideration ERC Recommendation 70-03 [i.3], annex 3 (frequency bands c2 and c3) and Commission Decision
2006/771/EC [i.4] bands 75a and 75b.
This radio equipment is capable of operating in all or any part of the frequency bands given in table 1.
Table 1: Radiocommunications service frequency band
Transmit/Receive Radiocommunications service frequency band
Transmit 57 GHz to 71 GHz
Receive 57 GHz to 71 GHz
NOTE 1: The technical characteristics of applications using these radio equipment are further described in ETSI
TR 103 583 [i.1].
NOTE 2: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.5] is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
Not applicable.
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI TR 103 583 (V1.1.1): "System Reference document (SRdoc); Technical characteristics of
Multiple Gigabit Wireless Systems (MGWS) in radio spectrum between 57 GHz and 71 GHz".
[i.2] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
ETSI
---------------------- Page: 8 ----------------------
9 ETSI EN 303 722 V1.2.1 (2022-03)
[i.3] ERC Recommendation 70-03 (Tromsø 1997 and subsequent amendments): "Related to the Use of
Short Range Devices (SRD)".
[i.4] Commission Decision 2006/771/EC of 9 November 2006 on harmonisation of the radio spectrum
for use by short-range devices (notified under document number C(2006) 5304) (Text with EEA
relevance).
NOTE: Av
...
SLOVENSKI STANDARD
SIST EN 303 722 V1.2.1:2022
01-maj-2022
Širokopasovni sistemi za prenos podatkov (WDTS) za radijsko opremo fiksnega
omrežja, ki delujejo v pasu od 57 GHz do 71 GHz - Harmonizirani standard za
dostop do radijskega spektra
Wideband Data Transmission Systems (WDTS) for Fixed Network Radio Equipment
operating in the 57 GHz to 71 GHz band - Harmonised Standard for access to radio
spectrum
Ta slovenski standard je istoveten z: ETSI EN 303 722 V1.2.1 (2022-03)
ICS:
33.060.01 Radijske komunikacije na Radiocommunications in
splošno general
SIST EN 303 722 V1.2.1:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 303 722 V1.2.1:2022
---------------------- Page: 2 ----------------------
SIST EN 303 722 V1.2.1:2022
ETSI EN 303 722 V1.2.1 (2022-03)
HARMONISED EUROPEAN STANDARD
Wideband Data Transmission Systems (WDTS)
for Fixed Network Radio Equipment operating
in the 57 GHz to 71 GHz band;
Harmonised Standard for access to radio spectrum
---------------------- Page: 3 ----------------------
SIST EN 303 722 V1.2.1:2022
2 ETSI EN 303 722 V1.2.1 (2022-03)
Reference
DEN/BRAN-230025
Keywords
60 GHz, access, broadband, fixed networks, radio,
SRD
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2022.
All rights reserved.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 303 722 V1.2.1:2022
3 ETSI EN 303 722 V1.2.1 (2022-03)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 Conformance requirements . 10
4.2.1 Spectral power density . 10
4.2.1.0 Applicability. 10
4.2.1.1 Definition . 11
4.2.1.2 Limit . 11
4.2.1.3 Conformance . 11
4.2.2 RF output power . 11
4.2.2.0 Applicability. 11
4.2.2.1 Definition . 11
4.2.2.2 Limit . 11
4.2.2.3 Conformance . 11
4.2.3 Transmitter unwanted emissions in the spurious domain . 12
4.2.3.0 Applicability. 12
4.2.3.1 Definition . 12
4.2.3.2 Limit . 12
4.2.3.3 Conformance . 12
4.2.4 Transmitter out-of-band emissions . 12
4.2.4.0 Applicability. 12
4.2.4.1 Definition . 12
4.2.4.2 Limit . 13
4.2.4.3 Conformance . 13
4.2.5 Adaptivity (medium access protocol) . 13
4.2.5.1 Applicability. 13
4.2.5.2 Definition . 13
4.2.5.3 Limit . 14
4.2.5.3.0 General . 14
4.2.5.3.1 Automatic Transmit Power Control. 14
4.2.5.3.2 Automatic Link Adaptation . 14
4.2.5.4 Conformance . 14
4.2.6 Occupied Channel Bandwidth . 14
4.2.6.1 Applicability. 14
4.2.6.2 Definition . 14
4.2.6.3 Limit . 14
4.2.6.4 Conformance . 14
4.2.7 Receiver unwanted emissions in the spurious domain . 14
4.2.7.0 Applicability. 14
4.2.7.1 Definition . 15
4.2.7.2 Limit . 15
4.2.7.3 Conformance . 15
4.2.8 Receiver Blocking . 15
4.2.8.1 Applicability. 15
ETSI
---------------------- Page: 5 ----------------------
SIST EN 303 722 V1.2.1:2022
4 ETSI EN 303 722 V1.2.1 (2022-03)
4.2.8.2 Definition . 15
4.2.8.3 Performance Criteria . 15
4.2.8.4 Limit . 15
4.2.8.5 Conformance . 16
4.2.9 Receiver Sensitivity level . 16
4.2.9.1 Applicability. 16
4.2.9.2 Definition . 16
4.2.9.3 Limit . 16
4.2.9.4 Conformance . 16
5 Testing for compliance with technical requirements . 16
5.1 Environmental conditions for testing . 16
5.1.1 General . 16
5.1.2 Normal test conditions . 16
5.1.2.1 Normal temperature and humidity . 16
5.1.2.2 Normal power source . 17
5.1.3 Extreme test conditions . 17
5.2 Test procedure for the essential radio test suites . 17
5.2.0 General . 17
5.2.1 Product Information . 17
5.2.2 Test modulation, frequency and configuration . 17
5.2.3 Spectral power density . 18
5.2.3.1 Test conditions . 18
5.2.3.2 Test method . 18
5.2.4 RF output power . 19
5.2.4.1 Test conditions . 19
5.2.4.2 Test method . 19
5.2.5 Transmitter unwanted emissions in the spurious domain . 20
5.2.5.0 Test conditions . 20
5.2.5.1 Pre-scan . 20
5.2.5.2 Identified emissions . 21
5.2.6 Transmitter out-of-band emissions . 22
5.2.6.1 Test conditions . 22
5.2.6.2 Test method . 22
5.2.7 Adaptivity (medium access protocol) . 22
5.2.7.1 Test conditions . 22
5.2.7.2 Test method (ATPC) . 22
5.2.7.3 Test method (ALA) . 24
5.2.8 Occupied Channel Bandwidth . 24
5.2.8.1 Test conditions . 24
5.2.8.2 Test method . 25
5.2.9 Receiver unwanted emissions in the spurious domain . 25
5.2.9.0 Test conditions . 25
5.2.9.1 Pre-scan . 26
5.2.9.2 Identified emissions . 26
5.2.10 Receiver Blocking . 26
5.2.10.1 Test conditions . 26
5.2.10.2 Test Method . 27
5.2.11 Receiver sensitivity level . 28
5.2.11.1 Test conditions . 28
5.2.11.2 Test method . 28
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 29
Annex B (informative): Maximum Measurement Uncertainty . 31
Annex C (normative): Test sites and arrangements for radiated measurements . 32
C.1 Test sites . 32
C.1.1 Open air test sites . 32
C.1.2 Anechoic chamber . 33
C.1.2.1 General . 33
ETSI
---------------------- Page: 6 ----------------------
SIST EN 303 722 V1.2.1:2022
5 ETSI EN 303 722 V1.2.1 (2022-03)
C.1.2.2 Description . 33
C.1.2.3 Influence of parasitic reflections . 33
C.1.2.4 Calibration and mode of use . 33
C.2 Test antenna . 35
C.3 Substitution antenna . 35
Annex D (normative): General description of measurement . 36
D.1 Radiated measurements . 36
D.2 Substitution measurement . 37
Annex E (informative): Bibliography . 38
Annex F (informative): Change History . 39
History . 40
ETSI
---------------------- Page: 7 ----------------------
SIST EN 303 722 V1.2.1:2022
6 ETSI EN 303 722 V1.2.1 (2022-03)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its
Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Broadband Radio Access
Networks (BRAN).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.5].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
National transposition dates
Date of adoption of this EN: 10 March 2022
Date of latest announcement of this EN (doa): 30 June 2022
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 December 2022
Date of withdrawal of any conflicting National Standard (dow): 31 December 2023
ETSI
---------------------- Page: 8 ----------------------
SIST EN 303 722 V1.2.1:2022
7 ETSI EN 303 722 V1.2.1 (2022-03)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 9 ----------------------
SIST EN 303 722 V1.2.1:2022
8 ETSI EN 303 722 V1.2.1 (2022-03)
1 Scope
The present document specifies technical characteristics and methods of measurements for Wideband Data
Transmission Systems (WDTS) fixed network radio equipment operating in the 57 GHz to 71 GHz band taking into
consideration ERC Recommendation 70-03 [i.3], annex 3 (frequency bands c2 and c3) and Commission Decision
2006/771/EC [i.4] bands 75a and 75b.
This radio equipment is capable of operating in all or any part of the frequency bands given in table 1.
Table 1: Radiocommunications service frequency band
Transmit/Receive Radiocommunications service frequency band
Transmit 57 GHz to 71 GHz
Receive 57 GHz to 71 GHz
NOTE 1: The technical characteristics of applications using these radio equipment are further described in ETSI
TR 103 583 [i.1].
NOTE 2: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.5] is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
Not applicable.
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced docume
...
Draft ETSI EN 303 722 V1.1.0 (2021-07)
HARMONISED EUROPEAN STANDARD
Wideband Data Transmission Systems (WDTS)
for Fixed Network Radio Equipment operating
in the 57 GHz to 71 GHz band;
Harmonised Standard for access to radio spectrum
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 303 722 V1.1.0 (2021-07)
Reference
DEN/BRAN-230025
Keywords
60 GHz, access, broadband, fixed networks, radio,
SRD
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2021.
All rights reserved.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 303 722 V1.1.0 (2021-07)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 Conformance requirements . 10
4.2.1 Spectral power density . 10
4.2.1.0 Applicability. 10
4.2.1.1 Definition . 11
4.2.1.2 Limit . 11
4.2.1.3 Conformance . 11
4.2.2 RF output power . 11
4.2.2.0 Applicability. 11
4.2.2.1 Definition . 11
4.2.2.2 Limit . 11
4.2.2.3 Conformance . 11
4.2.3 Transmitter unwanted emissions in the spurious domain . 12
4.2.3.0 Applicability. 12
4.2.3.1 Definition . 12
4.2.3.2 Limit . 12
4.2.3.3 Conformance . 12
4.2.4 Transmitter out-of-band emissions . 12
4.2.4.0 Applicability. 12
4.2.4.1 Definition . 12
4.2.4.2 Limit . 13
4.2.4.3 Conformance . 13
4.2.5 Adaptivity (medium access protocol) . 13
4.2.5.1 Applicability. 13
4.2.5.2 Definition . 13
4.2.5.3 Limit . 14
4.2.5.3.0 General . 14
4.2.5.3.1 Automatic Transmit Power Control. 14
4.2.5.3.2 Automatic Link Adaptation . 14
4.2.5.4 Conformance . 14
4.2.6 Occupied Channel Bandwidth . 14
4.2.6.1 Applicability. 14
4.2.6.2 Definition . 14
4.2.6.3 Limit . 14
4.2.6.4 Conformance . 14
4.2.7 Receiver unwanted emissions in the spurious domain . 14
4.2.7.0 Applicability. 14
4.2.7.1 Definition . 15
4.2.7.2 Limit . 15
4.2.7.3 Conformance . 15
4.2.8 Receiver Blocking . 15
4.2.8.1 Applicability. 15
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 303 722 V1.1.0 (2021-07)
4.2.8.2 Definition . 15
4.2.8.3 Performance Criteria . 15
4.2.8.4 Limit . 15
4.2.8.5 Conformance . 16
4.2.9 Receiver Sensitivity level . 16
4.2.9.1 Applicability. 16
4.2.9.2 Definition . 16
4.2.9.3 Limit . 16
4.2.9.4 Conformance . 16
5 Testing for compliance with technical requirements . 16
5.1 Environmental conditions for testing . 16
5.1.1 General . 16
5.1.2 Normal test conditions . 17
5.1.2.1 Normal temperature and humidity . 17
5.1.2.2 Normal power source . 17
5.1.3 Extreme test conditions . 17
5.2 Test procedure for the essential radio test suites . 17
5.2.0 General . 17
5.2.1 Product Information . 17
5.2.2 Test modulation, frequency and configuration . 17
5.2.3 Spectral power density . 18
5.2.3.1 Test conditions . 18
5.2.3.2 Test method . 18
5.2.4 RF output power . 19
5.2.4.1 Test conditions . 19
5.2.4.2 Test method . 19
5.2.5 Transmitter unwanted emissions in the spurious domain . 20
5.2.5.0 Test conditions . 20
5.2.5.1 Pre-scan . 20
5.2.5.2 Identified emissions . 21
5.2.6 Transmitter out-of-band emissions . 22
5.2.6.1 Test conditions . 22
5.2.6.2 Test method . 22
5.2.7 Adaptivity (medium access protocol) . 23
5.2.7.1 Test conditions . 23
5.2.7.2 Test method (ATPC) . 23
5.2.7.3 Test method (ALA) . 24
5.2.8 Occupied Channel Bandwidth . 25
5.2.8.1 Test conditions . 25
5.2.8.2 Test method . 25
5.2.9 Receiver unwanted emissions in the spurious domain . 25
5.2.9.0 Test conditions . 25
5.2.9.1 Pre-scan . 26
5.2.9.2 Identified emissions . 26
5.2.10 Receiver Blocking . 27
5.2.10.1 Test conditions . 27
5.2.10.2 Test Method . 27
5.2.11 Receiver sensitivity level . 28
5.2.11.1 Test conditions . 28
5.2.11.2 Test method . 28
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 29
Annex B (informative): Maximum Measurement Uncertainty . 31
Annex C (normative): Test sites and arrangements for radiated measurements . 32
C.1 Test sites . 32
C.1.1 Open air test sites . 32
C.1.2 Anechoic chamber . 33
C.1.2.1 General . 33
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 303 722 V1.1.0 (2021-07)
C.1.2.2 Description . 33
C.1.2.3 Influence of parasitic reflections . 33
C.1.2.4 Calibration and mode of use . 33
C.2 Test antenna . 35
C.3 Substitution antenna . 35
Annex D (normative): General description of measurement . 36
D.1 Radiated measurements . 36
D.2 Substitution measurement . 37
Annex E (informative): Bibliography . 38
Annex F (informative): Change History . 39
History . 40
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 303 722 V1.1.0 (2021-07)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its
Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Broadband Radio
Access Networks (BRAN), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI
standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.5].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 303 722 V1.1.0 (2021-07)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 303 722 V1.1.0 (2021-07)
1 Scope
The present document specifies technical characteristics and methods of measurements for Wideband Data
Transmission Systems (WDTS) fixed network radio equipment operating in the 57 GHz to 71 GHz band taking into
consideration ERC/REC 70-03 [i.3] annex 3 (frequency bands c2 and c3) and Commission Decision 2006/771/EC [i.4]
bands 75a and 75b.
This radio equipment is capable of operating in all or any part of the frequency bands given in table 1.
Table 1: Radiocommunications service frequency band
Transmit/Receive Radiocommunications service frequency band
Transmit 57 GHz to 71 GHz
Receive 57 GHz to 71 GHz
NOTE 1: The technical characteristics of applications using these radio equipment are further described in ETSI
TR 103 583 [i.1].
NOTE 2: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.5] is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific reference, only the cited version applies. For non-specific reference, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
Not applicable.
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI TR 103 583 (V1.1.1): "System Reference document (SRdoc); Technical characteristics of
Multiple Gigabit Wireless Systems (MGWS) in radio spectrum between 57 GHz and 71 GHz".
[i.2] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
ETSI
---------------------- Page: 8 ----------------------
9 Draft ETSI EN 303 722 V1.1.0 (2021-07)
[i.3] ERC Recommendation 70-03 (Tromsø 1997 and subsequent amendments): "Related to the Use of
Short Range Devices (SRD)".
[i.4] Commission Decision of 9 November 2006 on harmonisation
...
SLOVENSKI STANDARD
oSIST prEN 303 722 V1.2.0:2022
01-februar-2022
Širokopasovni sistemi za prenos podatkov (WDTS) za radijsko opremo fiksnega
omrežja, ki delujejo v pasu od 57 GHz do 71 GHz - Harmonizirani standard za
dostop do radijskega spektra
Wideband Data Transmission Systems (WDTS) for Fixed Network Radio Equipment
operating in the 57 GHz to 71 GHz band - Harmonised Standard for access to radio
spectrum
Ta slovenski standard je istoveten z: ETSI EN 303 722 V1.2.0 (2021-12)
ICS:
33.060.01 Radijske komunikacije na Radiocommunications in
splošno general
oSIST prEN 303 722 V1.2.0:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 303 722 V1.2.0:2022
---------------------- Page: 2 ----------------------
oSIST prEN 303 722 V1.2.0:2022
Draft ETSI EN 303 722 V1.2.0 (2021-12)
HARMONISED EUROPEAN STANDARD
Wideband Data Transmission Systems (WDTS)
for Fixed Network Radio Equipment operating
in the 57 GHz to 71 GHz band;
Harmonised Standard for access to radio spectrum
---------------------- Page: 3 ----------------------
oSIST prEN 303 722 V1.2.0:2022
2 Draft ETSI EN 303 722 V1.2.0 (2021-12)
Reference
DEN/BRAN-230025
Keywords
60 GHz, access, broadband, fixed networks, radio,
SRD
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2021.
All rights reserved.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 303 722 V1.2.0:2022
3 Draft ETSI EN 303 722 V1.2.0 (2021-12)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 Conformance requirements . 10
4.2.1 Spectral power density . 10
4.2.1.0 Applicability. 10
4.2.1.1 Definition . 11
4.2.1.2 Limit . 11
4.2.1.3 Conformance . 11
4.2.2 RF output power . 11
4.2.2.0 Applicability. 11
4.2.2.1 Definition . 11
4.2.2.2 Limit . 11
4.2.2.3 Conformance . 11
4.2.3 Transmitter unwanted emissions in the spurious domain . 12
4.2.3.0 Applicability. 12
4.2.3.1 Definition . 12
4.2.3.2 Limit . 12
4.2.3.3 Conformance . 12
4.2.4 Transmitter out-of-band emissions . 12
4.2.4.0 Applicability. 12
4.2.4.1 Definition . 12
4.2.4.2 Limit . 13
4.2.4.3 Conformance . 13
4.2.5 Adaptivity (medium access protocol) . 13
4.2.5.1 Applicability. 13
4.2.5.2 Definition . 13
4.2.5.3 Limit . 14
4.2.5.3.0 General . 14
4.2.5.3.1 Automatic Transmit Power Control. 14
4.2.5.3.2 Automatic Link Adaptation . 14
4.2.5.4 Conformance . 14
4.2.6 Occupied Channel Bandwidth . 14
4.2.6.1 Applicability. 14
4.2.6.2 Definition . 14
4.2.6.3 Limit . 14
4.2.6.4 Conformance . 14
4.2.7 Receiver unwanted emissions in the spurious domain . 14
4.2.7.0 Applicability. 14
4.2.7.1 Definition . 15
4.2.7.2 Limit . 15
4.2.7.3 Conformance . 15
4.2.8 Receiver Blocking . 15
4.2.8.1 Applicability. 15
ETSI
---------------------- Page: 5 ----------------------
oSIST prEN 303 722 V1.2.0:2022
4 Draft ETSI EN 303 722 V1.2.0 (2021-12)
4.2.8.2 Definition . 15
4.2.8.3 Performance Criteria . 15
4.2.8.4 Limit . 15
4.2.8.5 Conformance . 16
4.2.9 Receiver Sensitivity level . 16
4.2.9.1 Applicability. 16
4.2.9.2 Definition . 16
4.2.9.3 Limit . 16
4.2.9.4 Conformance . 16
5 Testing for compliance with technical requirements . 16
5.1 Environmental conditions for testing . 16
5.1.1 General . 16
5.1.2 Normal test conditions . 16
5.1.2.1 Normal temperature and humidity . 16
5.1.2.2 Normal power source . 17
5.1.3 Extreme test conditions . 17
5.2 Test procedure for the essential radio test suites . 17
5.2.0 General . 17
5.2.1 Product Information . 17
5.2.2 Test modulation, frequency and configuration . 17
5.2.3 Spectral power density . 18
5.2.3.1 Test conditions . 18
5.2.3.2 Test method . 18
5.2.4 RF output power . 19
5.2.4.1 Test conditions . 19
5.2.4.2 Test method . 19
5.2.5 Transmitter unwanted emissions in the spurious domain . 20
5.2.5.0 Test conditions . 20
5.2.5.1 Pre-scan . 20
5.2.5.2 Identified emissions . 21
5.2.6 Transmitter out-of-band emissions . 22
5.2.6.1 Test conditions . 22
5.2.6.2 Test method . 22
5.2.7 Adaptivity (medium access protocol) . 22
5.2.7.1 Test conditions . 22
5.2.7.2 Test method (ATPC) . 22
5.2.7.3 Test method (ALA) . 24
5.2.8 Occupied Channel Bandwidth . 24
5.2.8.1 Test conditions . 24
5.2.8.2 Test method . 25
5.2.9 Receiver unwanted emissions in the spurious domain . 25
5.2.9.0 Test conditions . 25
5.2.9.1 Pre-scan . 26
5.2.9.2 Identified emissions . 26
5.2.10 Receiver Blocking . 26
5.2.10.1 Test conditions . 26
5.2.10.2 Test Method . 27
5.2.11 Receiver sensitivity level . 28
5.2.11.1 Test conditions . 28
5.2.11.2 Test method . 28
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 29
Annex B (informative): Maximum Measurement Uncertainty . 31
Annex C (normative): Test sites and arrangements for radiated measurements . 32
C.1 Test sites . 32
C.1.1 Open air test sites . 32
C.1.2 Anechoic chamber . 33
C.1.2.1 General . 33
ETSI
---------------------- Page: 6 ----------------------
oSIST prEN 303 722 V1.2.0:2022
5 Draft ETSI EN 303 722 V1.2.0 (2021-12)
C.1.2.2 Description . 33
C.1.2.3 Influence of parasitic reflections . 33
C.1.2.4 Calibration and mode of use . 33
C.2 Test antenna . 35
C.3 Substitution antenna . 35
Annex D (normative): General description of measurement . 36
D.1 Radiated measurements . 36
D.2 Substitution measurement . 37
Annex E (informative): Bibliography . 38
Annex F (informative): Change History . 39
History . 40
ETSI
---------------------- Page: 7 ----------------------
oSIST prEN 303 722 V1.2.0:2022
6 Draft ETSI EN 303 722 V1.2.0 (2021-12)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its
Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Broadband Radio
Access Networks (BRAN), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI
standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.5].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
ETSI
---------------------- Page: 8 ----------------------
oSIST prEN 303 722 V1.2.0:2022
7 Draft ETSI EN 303 722 V1.2.0 (2021-12)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 9 ----------------------
oSIST prEN 303 722 V1.2.0:2022
8 Draft ETSI EN 303 722 V1.2.0 (2021-12)
1 Scope
The present document specifies technical characteristics and methods of measurements for Wideband Data
Transmission Systems (WDTS) fixed network radio equipment operating in the 57 GHz to 71 GHz band taking into
consideration ERC Recommendation 70-03 [i.3], annex 3 (frequency bands c2 and c3) and Commission Decision
2006/771/EC [i.4] bands 75a and 75b.
This radio equipment is capable of operating in all or any part of the frequency bands given in table 1.
Table 1: Radiocommunications service frequency band
Transmit/Receive Radiocommunications service frequency band
Transmit 57 GHz to 71 GHz
Receive 57 GHz to 71 GHz
NOTE 1: The technical characteristics of applications using these radio equipment are further described in ETSI
TR 103 583 [i.1].
NOTE 2: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.5] is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
Not applicable.
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amend
...
SLOVENSKI STANDARD
oSIST prEN 303 722 V1.1.0:2021
01-oktober-2021
Širokopasovni sistemi za prenos podatkov (WDTS) za radijsko opremo fiksnega
omrežja, ki delujejo v pasu od 57 GHz do 71 GHz - Harmonizirani standard za
dostop do radijskega spektra
Wideband Data Transmission Systems (WDTS) for Fixed Network Radio Equipment
operating in the 57 GHz to 71 GHz band - Harmonised Standard for access to radio
spectrum
Ta slovenski standard je istoveten z: ETSI EN 303 722 V1.1.0 (2021-07)
ICS:
33.060.01 Radijske komunikacije na Radiocommunications in
splošno general
oSIST prEN 303 722 V1.1.0:2021 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 303 722 V1.1.0:2021
---------------------- Page: 2 ----------------------
oSIST prEN 303 722 V1.1.0:2021
Draft ETSI EN 303 722 V1.1.0 (2021-07)
HARMONISED EUROPEAN STANDARD
Wideband Data Transmission Systems (WDTS)
for Fixed Network Radio Equipment operating
in the 57 GHz to 71 GHz band;
Harmonised Standard for access to radio spectrum
---------------------- Page: 3 ----------------------
oSIST prEN 303 722 V1.1.0:2021
2 Draft ETSI EN 303 722 V1.1.0 (2021-07)
Reference
DEN/BRAN-230025
Keywords
60 GHz, access, broadband, fixed networks, radio,
SRD
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2021.
All rights reserved.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 303 722 V1.1.0:2021
3 Draft ETSI EN 303 722 V1.1.0 (2021-07)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 8
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Technical requirements specifications . 10
4.1 Environmental profile . 10
4.2 Conformance requirements . 10
4.2.1 Spectral power density . 10
4.2.1.0 Applicability. 10
4.2.1.1 Definition . 11
4.2.1.2 Limit . 11
4.2.1.3 Conformance . 11
4.2.2 RF output power . 11
4.2.2.0 Applicability. 11
4.2.2.1 Definition . 11
4.2.2.2 Limit . 11
4.2.2.3 Conformance . 11
4.2.3 Transmitter unwanted emissions in the spurious domain . 12
4.2.3.0 Applicability. 12
4.2.3.1 Definition . 12
4.2.3.2 Limit . 12
4.2.3.3 Conformance . 12
4.2.4 Transmitter out-of-band emissions . 12
4.2.4.0 Applicability. 12
4.2.4.1 Definition . 12
4.2.4.2 Limit . 13
4.2.4.3 Conformance . 13
4.2.5 Adaptivity (medium access protocol) . 13
4.2.5.1 Applicability. 13
4.2.5.2 Definition . 13
4.2.5.3 Limit . 14
4.2.5.3.0 General . 14
4.2.5.3.1 Automatic Transmit Power Control. 14
4.2.5.3.2 Automatic Link Adaptation . 14
4.2.5.4 Conformance . 14
4.2.6 Occupied Channel Bandwidth . 14
4.2.6.1 Applicability. 14
4.2.6.2 Definition . 14
4.2.6.3 Limit . 14
4.2.6.4 Conformance . 14
4.2.7 Receiver unwanted emissions in the spurious domain . 14
4.2.7.0 Applicability. 14
4.2.7.1 Definition . 15
4.2.7.2 Limit . 15
4.2.7.3 Conformance . 15
4.2.8 Receiver Blocking . 15
4.2.8.1 Applicability. 15
ETSI
---------------------- Page: 5 ----------------------
oSIST prEN 303 722 V1.1.0:2021
4 Draft ETSI EN 303 722 V1.1.0 (2021-07)
4.2.8.2 Definition . 15
4.2.8.3 Performance Criteria . 15
4.2.8.4 Limit . 15
4.2.8.5 Conformance . 16
4.2.9 Receiver Sensitivity level . 16
4.2.9.1 Applicability. 16
4.2.9.2 Definition . 16
4.2.9.3 Limit . 16
4.2.9.4 Conformance . 16
5 Testing for compliance with technical requirements . 16
5.1 Environmental conditions for testing . 16
5.1.1 General . 16
5.1.2 Normal test conditions . 17
5.1.2.1 Normal temperature and humidity . 17
5.1.2.2 Normal power source . 17
5.1.3 Extreme test conditions . 17
5.2 Test procedure for the essential radio test suites . 17
5.2.0 General . 17
5.2.1 Product Information . 17
5.2.2 Test modulation, frequency and configuration . 17
5.2.3 Spectral power density . 18
5.2.3.1 Test conditions . 18
5.2.3.2 Test method . 18
5.2.4 RF output power . 19
5.2.4.1 Test conditions . 19
5.2.4.2 Test method . 19
5.2.5 Transmitter unwanted emissions in the spurious domain . 20
5.2.5.0 Test conditions . 20
5.2.5.1 Pre-scan . 20
5.2.5.2 Identified emissions . 21
5.2.6 Transmitter out-of-band emissions . 22
5.2.6.1 Test conditions . 22
5.2.6.2 Test method . 22
5.2.7 Adaptivity (medium access protocol) . 23
5.2.7.1 Test conditions . 23
5.2.7.2 Test method (ATPC) . 23
5.2.7.3 Test method (ALA) . 24
5.2.8 Occupied Channel Bandwidth . 25
5.2.8.1 Test conditions . 25
5.2.8.2 Test method . 25
5.2.9 Receiver unwanted emissions in the spurious domain . 25
5.2.9.0 Test conditions . 25
5.2.9.1 Pre-scan . 26
5.2.9.2 Identified emissions . 26
5.2.10 Receiver Blocking . 27
5.2.10.1 Test conditions . 27
5.2.10.2 Test Method . 27
5.2.11 Receiver sensitivity level . 28
5.2.11.1 Test conditions . 28
5.2.11.2 Test method . 28
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 29
Annex B (informative): Maximum Measurement Uncertainty . 31
Annex C (normative): Test sites and arrangements for radiated measurements . 32
C.1 Test sites . 32
C.1.1 Open air test sites . 32
C.1.2 Anechoic chamber . 33
C.1.2.1 General . 33
ETSI
---------------------- Page: 6 ----------------------
oSIST prEN 303 722 V1.1.0:2021
5 Draft ETSI EN 303 722 V1.1.0 (2021-07)
C.1.2.2 Description . 33
C.1.2.3 Influence of parasitic reflections . 33
C.1.2.4 Calibration and mode of use . 33
C.2 Test antenna . 35
C.3 Substitution antenna . 35
Annex D (normative): General description of measurement . 36
D.1 Radiated measurements . 36
D.2 Substitution measurement . 37
Annex E (informative): Bibliography . 38
Annex F (informative): Change History . 39
History . 40
ETSI
---------------------- Page: 7 ----------------------
oSIST prEN 303 722 V1.1.0:2021
6 Draft ETSI EN 303 722 V1.1.0 (2021-07)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The declarations
pertaining to these essential IPRs, if any, are publicly available for ETSI members and non-members, and can be
found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to
ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the
ETSI Web server (https://ipr.etsi.org/).
Pursuant to the ETSI Directives including the ETSI IPR Policy, no investigation regarding the essentiality of IPRs,
including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not
referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become,
essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its
Members. 3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP
Organizational Partners. oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and of the
®
oneM2M Partners. GSM and the GSM logo are trademarks registered and owned by the GSM Association.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Broadband Radio
Access Networks (BRAN), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI
standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.2] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.5].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
ETSI
---------------------- Page: 8 ----------------------
oSIST prEN 303 722 V1.1.0:2021
7 Draft ETSI EN 303 722 V1.1.0 (2021-07)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 9 ----------------------
oSIST prEN 303 722 V1.1.0:2021
8 Draft ETSI EN 303 722 V1.1.0 (2021-07)
1 Scope
The present document specifies technical characteristics and methods of measurements for Wideband Data
Transmission Systems (WDTS) fixed network radio equipment operating in the 57 GHz to 71 GHz band taking into
consideration ERC/REC 70-03 [i.3] annex 3 (frequency bands c2 and c3) and Commission Decision 2006/771/EC [i.4]
bands 75a and 75b.
This radio equipment is capable of operating in all or any part of the frequency bands given in table 1.
Table 1: Radiocommunications service frequency band
Transmit/Receive Radiocommunications service frequency band
Transmit 57 GHz to 71 GHz
Receive 57 GHz to 71 GHz
NOTE 1: The technical characteristics of applications using these radio equipment are further described in ETSI
TR 103 583 [i.1].
NOTE 2: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.5] is given in annex A.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific reference, only the cited version applies. For non-specific reference, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
Not applicable.
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.