Metallic industrial piping - Part 3: Design and calculation

This Part of this European Standard specifies the design and calculation of industrial metallic piping systems, including supports, covered by EN 13480.

Metallische industrielle Rohrleitungen - Teil 3: Konstruktion und Berechnung

Tuyauteries industrielles métalliques - Partie 3: Conception et calcul

Kovinski industrijski cevovodi - 3. del: Konstruiranje in izračun - Dopolnilo A4

General Information

Status
Not Published
Public Enquiry End Date
02-Jun-2020
Technical Committee
Current Stage
5020 - Formal vote (FV) (Adopted Project)
Start Date
06-May-2021
Due Date
24-Jun-2021
Completion Date
02-Jun-2021

RELATIONS

Buy Standard

Amendment
SIST EN 13480-3:2018/oprA4:2020
English language
7 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN 13480-3:2018/oprA4:2020
01-maj-2020
Kovinski industrijski cevovodi - 3. del: Konstruiranje in izračun - Dopolnilo A4
Metallic industrial piping - Part 3: Design and calculation
Metallische industrielle Rohrleitungen - Teil 3: Konstruktion und Berechnung
Tuyauteries industrielles métalliques - Partie 3: Conception et calcul
Ta slovenski standard je istoveten z: EN 13480-3:2017/prA4
ICS:
23.040.10 Železne in jeklene cevi Iron and steel pipes
77.140.75 Jeklene cevi in cevni profili Steel pipes and tubes for
za posebne namene specific use
SIST EN 13480-3:2018/oprA4:2020 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 13480-3:2018/oprA4:2020
---------------------- Page: 2 ----------------------
SIST EN 13480-3:2018/oprA4:2020
DRAFT
EUROPEAN STANDARD
EN 13480-3:2017
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA4
April 2020
ICS 23.040.01
English Version
Metallic industrial piping - Part 3: Design and calculation

Tuyauteries industrielles métalliques - Partie 3: Metallische industrielle Rohrleitungen - Teil 3:

Conception et calcul Konstruktion und Berechnung

This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 267.

This draft amendment A4, if approved, will modify the European Standard EN 13480-3:2017. If this draft becomes an

amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for

inclusion of this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other

language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC

Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are

aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without

notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13480-3:2017/prA4:2020 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13480-3:2018/oprA4:2020
EN 13480-3:2017/prA4:2020 (E)
Contents

European foreword ....................................................................................................................................................... 3

1 Modifications to Clause 2, Normative references ................................................................................. 4

2 Modifications to 13.11, Manufacturing of pipe supports ................................................................... 4

3 Modifications to Annex N, Documentation of supports ...................................................................... 5

---------------------- Page: 4 ----------------------
SIST EN 13480-3:2018/oprA4:2020
EN 13480-3:2017/prA4:2020 (E)
European foreword

This document (EN 13480-3:2017/prA4:2020) has been prepared by Technical Committee CEN/TC 267

“Industrial piping and pipelines”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.

This document has been prepared under a mandate given to CEN by the European Commission and the

European Free Trade Association, and supports essential requirements of EU Directive(s).

For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this

document.

This document includes the text of the amendment itself. The amended/corrected pages of

EN 13480-3:2017 will be published as Issue 3 of the European Standard.
---------------------- Page: 5 ----------------------
SIST EN 13480-3:2018/oprA4:2020
EN 13480-3:2017/prA4:2020 (E)
1 Modifications to Clause 2, Normative references
In Clause 2, the following normative reference shall be added:

EN 1090-1:2009+A1:2011, Execution of steel structures and aluminium structures - Part 1: Requirements

for conformity assessment of structural components

EN 1090-2:2018, Execution of steel structures and aluminium structures - Part 2: Technical requirements

for steel structures
EN 1990:2002, Eurocode - Basis of structural design
EN 1991 (all parts), Eurocode 1: Actions on structures
2 Modifications to 13.11, Manufacturing of pipe supports
The heading of 13.11 shall read as follows:
13.11 Design and manufacture of pipe supports.
After 13.11.10, add a new subclause 13.11.1
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.