SIST EN 60603-7-2:2010

Connectors for electronic equipment -- Part 7-2: Detail specification for 8-way, unshielded, free and fixed connectors, for data transmissions with frequencies up to 100 MHz

This part of IEC 60603-7 covers 8-way, unshielded, free and fixed connectors, and specifies mechanical and environmental requirements, and electrical transmission requirements for frequencies up to 100 MHz. These connectors are typically used as category 5 connectors in class D cabling systems specified in ISO/IEC 11801:2002. These connectors are intermateable, interoperable, and backward compatible with other IEC 60603-7 series connectors. While the definition of interoperable is being discussed within IEC, "interoperable" in this standard means the following: The fixed and the free connector are capable of interconnecting with any IEC 60603-7 series connector, and that when it is interconnected, it fully meets all requirements of the lower frequency IEC 60603-7 series standard.

Steckverbinder für elektronische Einrichtungen -- Teil 7-2: Bauartspezifikation für ungeschirmte freie und feste Steckverbinder, 8polig, für Datenübertragungen bis 100 MHz

Connecteurs pour équipements électroniques -- Partie 7-2: Spécification particulière pour les fiches et les embases non blindées à 8 voies pour la transmission de données à des fréquences jusqu'à 100 MHz

Couvre les fiches et les embases non blindées à 8 voies et spécifie les exigences mécaniques et environnementales ainsi que les exigences de transmission électrique pour des fréquences jusqu'à 100 MHz. Ces connecteurs sont normalement utilisés comme connecteurs de catégorie 5 dans les systèmes de câblage de classe D spécifiés dans l'ISO/CEI  11801:2002. Ils sont accouplables, interopérables et offrent une compatibilité amont avec les autres connecteurs de la série CEI 60603-7.

Končniki za elektronsko opremo - 7-2. del: Podrobna specifikacija za 8-polne, neščitene, proste in pritrjene končnike, za prenos podatkov s frekvencami do 100 MHz

Ta del IEC 60603 zajema 8-polne, neščitene, proste in fiksne končnike ter določa mehanske in okoljske zahteve ter zahteve za prevajanje električnega toka za frekvence do 100 MHz. Ti končniki se praviloma uporabljajo kot končniki kategorije 5 v kabelskih sistemih razreda D, ki jih opredeljuje ISO/IEC 11801:2002. Ti končniki so medsebojno združljivi, interoperabilni in vzvratno združljivi z drugimi konektorji serije IEC 60603-7. Definicijo interoperabilnosti obravnava IEC, v tem standardu pa »interoperabilen« pomeni naslednje: fiksni in prosti končnik se lahko poveže s katerimkoli končnikom serije IEC 60603-7 in pri takšni povezavi v vseh pogledih izpolnjuje zahteve standarda serije IEC 60603-7 za nižje frekvence.

General Information

• Status: Published
• Publication Date: 15-Feb-2010
• ICS: 31.220.10 - Plug-and-socket devices. Connectors
• Technical Committee: I15 - Board tech
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 25-Jan-2010
• Due Date: 01-Apr-2010
• Completion Date: 16-Feb-2010
• Ref Project: EN 60603-7-2:2009 - Connectors for electronic equipment - Part 7-2: Detail specification for 8-way, unshielded, free and fixed connectors, for data transmissions with frequencies up to 100 MHz

Relations

• Replaced By: SIST EN 60603-7-2:2010 - Connectors for electronic equipment - Part 7-2: Detail specification for 8-way, unshielded, free and fixed connectors, for data transmissions with frequencies up to 100 MHz (IEC 60603-7-2:2010)
• Effective Date: 01-Jul-2013
• Replaced By: SIST EN 60603-7-2:2010 - Connectors for electronic equipment - Part 7-2: Detail specification for 8-way, unshielded, free and fixed connectors, for data transmissions with frequencies up to 100 MHz (IEC 60603-7-2:2010)
• Effective Date: 29-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60603-7-2:2010
01-marec-2010
.RQþQLNL]DHOHNWURQVNRRSUHPRGHO3RGUREQDVSHFLILNDFLMD]DSROQH
QHãþLWHQHSURVWHLQSULWUMHQHNRQþQLNH]DSUHQRVSRGDWNRYVIUHNYHQFDPLGR
0+]
Connectors for electronic equipment -- Part 7-2: Detail specification for 8-way,
unshielded, free and fixed connectors, for data transmissions with frequencies up to 100
MHz
Steckverbinder für elektronische Einrichtungen -- Teil 7-2: Bauartspezifikation für
ungeschirmte freie und feste Steckverbinder, 8polig, für Datenübertragungen bis 100
MHz
Connecteurs pour équipements électroniques -- Partie 7-2: Spécification particulière pour
les fiches et les embases non blindées à 8 voies pour la transmission de données à des
fréquences jusqu'à 100 MHz
Ta slovenski standard je istoveten z: EN 60603-7-2:2009
ICS:
31.220.10 9WLþLLQYWLþQLFHNRQHNWRUML Plug-and-socket devices.
Connectors
SIST EN 60603-7-2:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60603-7-2:2010

---------------------- Page: 2 ----------------------

SIST EN 60603-7-2:2010

EUROPEAN STANDARD
EN 60603-7-2

NORME EUROPÉENNE
November 2009
EUROPÄISCHE NORM

ICS 31.220.10


English version


Connectors for electronic equipment -
Part 7-2: Detail specification for 8-way,
unshielded, free and fixed connectors,
for data transmissions with frequencies up to 100 MHz
(IEC 60603-7-2:2007)


Connecteurs pour équipements Steckverbinder für elektronische
électroniques - Einrichtungen -
Partie 7-2: Spécification particulière Teil 7-2: Bauartspezifikation
pour les fiches et les embases für ungeschirmte freie und feste
non blindées à 8 voies Steckverbinder, 8polig,
pour la transmission de données für Datenübertragungen bis 100 MHz
à des fréquences jusqu'à 100 MHz (IEC 60603-7-2:2007)
(CEI 60603-7-2:2007)




This European Standard was approved by CENELEC on 2009-09-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: Avenue Marnix 17, B - 1000 Brussels


© 2009 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60603-7-2:2009 E

---------------------- Page: 3 ----------------------

SIST EN 60603-7-2:2010
EN 60603-7-2:2009 – 2 –
Foreword
The text of document 48B/1740/FDIS, future edition 1 of IEC 60603-7-2, prepared by SC 48B,
Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic
equipment, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60603-7-2 on 2009-09-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2010-06-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2012-09-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60603-7-2:2007 was approved by CENELEC as a European
Standard without any modification.
__________

---------------------- Page: 4 ----------------------

SIST EN 60603-7-2:2010
– 3 – EN 60603-7-2:2009

Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

1)
- - Communication cables - Specifications for EN 50289-1-14 -
test methods -
Part 1-14: Electrical test methods - Coupling
attenuation or screening attenuation of
connecting hardware


1)
IEC 60050-581 - International Electrotechnical Vocabulary - -
(IEV) -
Part 581: Electromechanical components for
electronic equipment


1) 2)
IEC 60068-1 - Environmental testing - EN 60068-1 1994
Part 1: General and guidance


1)
IEC 60068-2-38 - Environmental testing - EN 60068-2-38 2009
Part 2-38: Tests - Test Z/AD: Composite
temperature/humidity cyclic test


1)
IEC 60169-16 - Radio-frequency connectors - - -
Part 16: R.F. coaxial connectors with inner
diameter of outer conductor 7 mm (0,276 in)
with screw coupling - Characteristic
impedance 50 ohms (75 ohms) (type N)


IEC 60352 Series Solderless connections EN 60352 Series


IEC 60512 Series Connectors for electronic equipment - Tests EN 60512 Series
and measurements


1) 2)
IEC 60512-1-100 - Connectors for electronic equipment - Tests EN 60512-1-100 2006
and measurements -
Part 1-100: General - Applicable publications


1) 2)
IEC 60603-1 - Connectors for frequencies below 3 MHz for EN 60603-1 1998
use with printed boards -
Part 1: Generic specification - General
requirements and guide for the preparation of
detail specifications, with assessed quality


IEC 60603-7 Series Connectors for electronic equipment - EN 60603-7 Series
Part 7: Detail specifications for 8-way free and
fixed connectors


1) 2)
IEC 60664-1 - Insulation coordination for equipment within EN 60664-1 2007
low-voltage systems -
Part 1: Principles, requirements and tests



1)
Undated reference.
2)
Valid edition at date of issue.

---------------------- Page: 5 ----------------------

SIST EN 60603-7-2:2010
EN 60603-7-2:2009 – 4 –
Publication Year Title EN/HD Year

1) 2)
IEC 61076-1 - Connectors for electronic equipment - EN 61076-1 2006
Product requirements -
Part 1: Generic specification


IEC 61156 Series Multicore and symmetrical pair/quad cables - -
for digital communications


ISO/IEC 11801 2002 Information technology - Generic cabling for - -
customer premises


1) 2)
ISO 1302 - Geometrical Product Specifications (GPS) - EN ISO 1302 2002
Indication of surface texture in technical
product documentation


1)
ITU-T - Resistibility of telecommunication equipment - -
Recommendation installed in a telecommunications centre to
K.20 overvoltages and overcurrents


1)
ITU-T - Resistibility tests for telecommunication - -
Recommendation equipment exposed to overvoltages and
K.44 overcurrents - Basic Recommendation


1)
ITU-T - Transmission aspects of unbalance about - -
Recommendation earth
G.117


1)
ITU-T - Measuring arrangements to assess the - -
Recommendation degree of unbalance about earth
O.9

---------------------- Page: 6 ----------------------

SIST EN 60603-7-2:2010
NORME CEI
INTERNATIONALE
IEC



60603-7-2
INTERNATIONAL


Première édition
STANDARD

First edition

2007-03


Connecteurs pour équipements électroniques –
Partie 7-2:
Spécification particulière
pour les fiches et les embases non
blindées à 8 voies pour la transmission de
données à des fréquences jusqu’à 100 MHz

Connectors for electronic equipment –
Part 7-2:
Detail specification for 8-way,
unshielded, free and fixed connectors, for data
transmissions with frequencies up to 100 MHz
© IEC 2007 Droits de reproduction réservés ⎯ Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: [phone] Telefax: [phone] E-mail: [e-mail] Web: www.iec.ch
CODE PRIX
XC
PRICE CODE
Commission Electrotechnique Internationale
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
Pour prix, voir catalogue en vigueur
For price, see current catalogue

---------------------- Page: 7 ----------------------

SIST EN 60603-7-2:2010
60603-7-2 © IEC:2007 – 3 –
CONTENTS
FOREWORD.9
INTRODUCTION.13

1 General .15
1.1 Scope.15
1.2 Normative references .15
2 IEC type designation .19
2.1 Terms and definitions .21
3 Common features and isometric view .23
3.1 Isometric view .23
3.2 Mating information.23
4 Cable terminations and internal connections – fixed and free connectors .39
4.1 General .39
4.2 Termination types.39
5 Gauges .41
5.1 Fixed connectors .41
5.2 Free connectors .47
6 Characteristics .51
6.1 General .51
6.2 Pin and pair grouping assignment. .51
6.3 Classification into climatic category.51
6.4 Electrical characteristics.53
6.5 Transmission characteristics .57
6.6 Mechanical.61
7 Tests and test schedule.61
7.1 General .61
7.2 Arrangement for contact resistance test: .63
7.3 Arrangement for vibration test (test phase CP1) .65
7.4 Test procedures and measuring methods .65
7.5 Preconditioning .65
7.6 Wiring and mounting of specimens .67
7.7 Test schedules .67

Annex A (normative) Gauging continuity procedure.85
Annex B (normative) Locking-device mechanical operation.93
Annex C (normative) Test plug requirements .95
Annex D (normative) General requirements for the measurement set-up.123
Annex E (normative) Insertion loss .135
Annex F (normative) Return loss.139
Annex G (normative) Near end cross talk (NEXT) .143
Annex H (normative) Far end cross talk .147
Annex I (normative) Termination of balun.151
Annex J (normative) Gauge requirements .153

---------------------- Page: 8 ----------------------

SIST EN 60603-7-2:2010
60603-7-2 © IEC:2007 – 5 –
Figure 1 – Isometric view .23
Figure 2 – Contact interface dimensions with terminated free connector .25
Figure 3 – Fixed connector details .31
Figure 4 – Free connector view.35
Figure 5 – “Go” gauge.41
Figure 6 – No-go gauges .43
Figure 7 – “No-go” gauges .47
Figure 8 – “Go” gauge.49
Figure 9 – Fixed connector pin and pair grouping assignment (front view of connector) .51
Figure 10 – Connector de-rating curve .55
Figure 11 – Arrangement for contact resistance test .63
Figure 12 – Arrangement for vibration test .65
Figure A.1 – Gauge.89
Figure A.2 – Gauge insertion .91
Figure C.1 – De-embedding reference plug.97
Figure C.2 – De-embedding reference jack .101
Figure C.3 – THI3KIT test head interface with baluns attached .113
Figure C.4 – Alternative to item 3.1 in Table C.5.117
Figure C.5 – Back-to-back through calibration.117
Figure C.6 – Mated test plug/coaxial termination reference test head test configuration.121
Figure D.1 – 180° hybrid used as a balun .125
Figure D.2 – Calibration of reference loads.127
Figure D.3 – Resistor load .129
Figure D.4 – Screened pyramid.131
Figure D.5 – Definition of reference planes .133
Figure E.1 – Calibration .135
Figure E.2 – Measuring Set-up .137
Figure G.1 – NEXT measurement for differential and common mode terminations .143
Figure H.1 – FEXT measurement differential and common mode terminations .147
Figure I.1 – Balanced attenuator for balun centre tap grounded .151
Figure I.2 – Balanced attenuator for balun centre tap open .151

Table 1 – Dimensions for Figure 2 .27
Table 2 – Dimensions for Figure 3 .33
Table 3 – Dimensions for Figure 4 .37
Table 4 – Dimensions for Figures 5 and 6.45
Table 5 – Dimensions for Figure 7 .47
Table 6 – Dimensions for Figure 8 .49

---------------------- Page: 9 ----------------------

SIST EN 60603-7-2:2010
60603-7-2 © IEC:2007 – 7 –
Table 7 – Climatic categories – selected values.51
Table 8 – Creepage and clearance distances.53
Table 9 – Test group P .69
Table 10 – Test group AP .71
Table 11 – Test group BP .75
Table 12 – Test group CP .77
Table 13 – Test group DP .79
Table 14 – Test group EP .81
Table 15 – Test group FP .83
Table 16 – Test group GP.83
Table A.1 – Dimensions for Figure A.1.87
Table C.1 – De-embedded real and imaginary reference jack vectors .105
Table C.2 – Test plug NEXT loss limits .107
Table C.3 – Test plug NEXT loss ranges.109
Table C.4 – Coaxial termination reference head component list .111
Table C.5 – Coaxial termination reference head, additional parts.115
Table C.6 – Return loss requirements for return loss reference plug .121
Table D.1 – Test balun performance characteristics.127
Table F.1 – Uncertainty band of return loss measurement at frequencies below
100 MHz .141
Table F.2 – Uncertainty band of return loss measurement at frequencies above
100 MHz .141

---------------------- Page: 10 ----------------------

SIST EN 60603-7-2:2010
60603-7-2 © IEC:2007 – 9 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

CONNECTORS FOR ELECTRONIC EQUIPMENT –

Part 7-2: Detail specification for 8-way, unshielded,
free and fixed connectors, for data transmissions
with frequencies up to 100 MHz


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60603-7-2 has been prepared by subcommittee 48B: Connectors,
of IEC technical committee 48: Electromechanical components and mechanical structures for
electronic equipment.
The text of this standard is based on the following documents:
FDIS Report on voting
48B/1740/FDIS 48B/1748/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

---------------------- Page: 11 ----------------------

SIST EN 60603-7-2:2010
60603-7-2 © IEC:2007 – 11 –
A list of all parts of the IEC 60603 series, under the general title Connectors for electronic
equipment, can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 12 ----------------------

SIST EN 60603-7-2:2010
60603-7-2 © IEC:2007 – 13 –
INTRODUCTION
Applications have emerged which require the use of the interface described in IEC 60603-7:
1996 with certain performance specifications at higher frequencies. The parameters for this
performance include insertion loss, near end crosstalk (NEXT), far end crosstalk (FEXT), and
return loss. Based on application requirements, the specifications for these parameters
always apply to a mated connection of a free (plug) and fixed (outlet) connector. Details for
testing of connectors and test plugs are given in Annex C.

---------------------- Page: 13 ----------------------

SIST EN 60603-7-2:2010
60603-7-2 © IEC:2007 – 15 –
CONNECTORS FOR ELECTRONIC EQUIPMENT –

Part 7-2: Detail specification for 8-way, unshielded,
free and fixed connectors, for data transmissions
with frequencies up to 100 MHz



1 General
1.1 Scope
This part of IEC 60603-7 covers 8-way, unshielded, free and fixed connectors, and specifies
mechanical and environmental requirements, and electrical transmission requirements for
frequencies up to 100 MHz. These connectors are typically used as category 5 connectors in
class D cabling systems specified in ISO/IEC 11801:2002.
These connectors are intermateable, interoperable, and backward compatible with other
IEC 60603-7 series connectors. While the definition of interoperable is being discussed within
IEC, “interoperable” in this standard means the following: The fixed and the free connector
are capable of interconnecting with any IEC 60603-7 series connector, and that when it is
interconnected, it fully meets all requirements of the lower frequency IEC 60603-7 series
standard.
NOTE Transmission performance categories: in this part of IEC 60603-7, the term “category”, when used in
reference to transmission performance, refers to those categories defined by ISO/IEC 11801:2002.
1.2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 60050(581), International Electrotechnical Vocabulary (IEV) – Chapter 581: Electro-
mechanical components for electronic equipment
IEC 60068-1, Environmental testing – Part 1: General and guidance
IEC 60068-2-38, Environmental testing – Part 2: Tests. Test Z/AD: Composite
temperature/humidity cyclic test
IEC 60169-16, Radio frequency connectors – Part 16: R.F. coaxial connectors with inner
diameter of outer conductor 7 mm (0,276 in) with screw coupling – Characteristic impedance
50 ohms (75 ohms) (Type N)
IEC 60352 (all parts), Solderless connections
IEC 60512 (all parts), Connectors for electronic equipment – Tests and measurements
IEC 60512-1-100, Connectors for electronic equipment – Tests and measurements –
Part 1-100: General – Applicable publications

---------------------- Page: 14 ----------------------

SIST EN 60603-7-2:2010
60603-7-2 © IEC:2007 – 17 –
IEC 60603-1, Connectors for frequencies below 3 MHz for use with printed boards – Part 1:
Generic specification – General requirements and guide for the preparation of detail
specifications, with assessed quality
...