oSIST prEN 10253-3:2004
(Main)Butt-welding pipe fittings - Part 3: Wrought austenitic and austenitic-ferritic (duplex) stainless steels without specific inspection requirements
Butt-welding pipe fittings - Part 3: Wrought austenitic and austenitic-ferritic (duplex) stainless steels without specific inspection requirements
This part of EN 10253 specifies the technical delivery requirements for seamless and welded butt-welding fittings made of austenitic and austenitic-ferritic (duplex) stainless steels and delivered without specific inspection
Butt-welding pipe fittings - Part 3: Wrought austenitic and austenitic-ferritic (duplex) stainless steels without specific inspection requirements
General Information
Standards Content (Sample)
SLOVENSKI OSIST prEN 10253-3:2004
PREDSTANDARD
november 2004
Butt-welding pipe fittings - Part 3: Wrought austenitic and austenitic-ferritic (duplex)
stainless steels without specific inspection requirements
ICS 23.040.40; 77.140.20 Refere
...
This May Also Interest You
This draft European Standard specifies the technical delivery requirements for seamless and welded butt welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of carbon and alloy steel in two test categories which are intended for pressure purposes at room temperature, at low temperature or at elevated temperatures, and for the transmission and distribution of fluids and gases.
It specifies:
a) type of fittings;
1) type A: Butt-welding fittings with reduced pressure factor;
2) type B: Butt-welding fittings for use at full service pressure;
b) steel grades and their chemical compositions;
c) mechanical properties;
d) dimensions and tolerances;
e) requirements for inspection and testing;
f) inspection documents;
g) marking;
h) protection and packaging.
NOTE In the case of a harmonised supporting standard for materials, presumption of conformity to the ESRs is limited to technical data of materials in the standard and does not presume adequacy of the material to a specific item of equipment. Consequently it is essential that the technical data stated in the material standard be assessed against the design requirements of this specific item of equipment to verify that the ESRs of the PED are satisfied.
- Standard145 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft149 pagesEnglish languagesale 10% offe-Library read for×1 day
1.1 This Part of EN 10253 specifies the technical delivery requirements for seamless and welded butt-welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of austenitic and austenitic-ferritic (duplex) stainless steel which are applied for pressure and corrosion resisting purposes at room temperature, at low temperature or at elevated temperatures.
It specifies:
- the type of fittings;
- type A : Butt-welding fittings with reduced pressure factor;
- type B : Butt-welding fittings for use at full service pressure;
- the steel grades;
- the mechanical properties;
- the dimensions and tolerances;
- the requirements for inspection and testing;
- the inspection documents;
- the marking;
- the handling and packaging.
1.2 Unless otherwise specified in this Part of EN 10253 the general technical delivery requirements in EN 10021 apply.
- Corrigendum3 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of EN 10253 specifies the technical delivery requirements for seamless and welded buttwelding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of austenitic and austenitic - ferritic (duplex) stainless steel without specific inspection requirements. It specifies : - the steel grades ; - the mechanical properties ; - the dimensions and tolerances ; - the requirements for inspection and testing ; - the inspection documents ; - the marking ; - the handling and packaging. Unless otherwise specified in this part of EN 10253 the general technical delivery requirements in EN 10021 shall apply. Limitation of use The allowed pressures and temperatures are the responsibility of the customer according to the state of the art and in application of the safety coefficients in the application regulations, codes and standards. In common, joint coefficient are used in the calculation of the thicknesses of components which include one or several butt welds, other than circumferential : - for equipment subject to random non-destructive testing : 0,85 ; - for equipment not subject to non-destructive testing other than visual inspection : 0,7.
- Standard47 pagesEnglish languagesale 10% offe-Library read for×1 day
1.1 This Part of EN 10253 specifies the technical delivery requirements for seamless and welded butt-welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of austenitic and austenitic-ferritic (duplex) stainless steel which are applied for pressure and corrosion resisting purposes at room temperature, at low temperature or at elevated temperatures.
It specifies:
- the type of fittings;
- type A : Butt-welding fittings with reduced pressure factor;
- type B : Butt-welding fittings for use at full service pressure;
- the steel grades;
- the mechanical properties;
- the dimensions and tolerances;
- the requirements for inspection and testing;
- the inspection documents;
- the marking;
- the handling and packaging.
1.2 Unless otherwise specified in this Part of EN 10253 the general technical delivery requirements in EN 10021 apply.
- Standard97 pagesEnglish languagesale 10% offe-Library read for×1 day
This draft European Standard specifies the technical delivery requirements for seamless and welded butt-welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of austenitic and austenitic-ferritic (duplex) stainless steel in two test-categories which are intended for pressure purposes at room temperature, at low temperature or at elevated temperatures, and for the transmission and distribution of fluids and gases.
It specifies:
a) type of fittings;
1) type A: butt-welding fittings with reduced pressure factor;
2) type B: butt-welding fittings for use at full service pressure;
b) steel grades and their chemical compositions;
c) mechanical properties;
d) dimensions and tolerances;
e) requirements for inspection and testing;
f) inspection documents;
g) marking;
h) protection and packaging.
NOTE In the case of a harmonised supporting standard for materials, presumption of conformity to the ESRs is limited to technical data of materials in the standard and does not presume adequacy of the material to a specific item of equipment. Consequently it is essential that the technical data stated in the material standard be assessed against the design requirements of this specific item of equipment to verify that the ESRs of the PED are satisfied.
- Draft156 pagesEnglish languagesale 10% offe-Library read for×1 day
- 31-Jan-2018
- 23.040.40
- 77.140.20
- 2014/68/EU
- 97/23/EC
- IFEK
This draft European Standard specifies the technical delivery requirements for seamless and welded butt welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of carbon and alloy steel in two test categories which are intended for pressure purposes at room temperature, at low temperature or at elevated temperatures, and for the transmission and distribution of fluids and gases.
It specifies:
a) type of fittings;
1) type A: Butt-welding fittings with reduced pressure factor;
2) type B: Butt-welding fittings for use at full service pressure;
b) steel grades and their chemical compositions;
c) mechanical properties;
d) dimensions and tolerances;
e) requirements for inspection and testing;
f) inspection documents;
g) marking;
h) protection and packaging.
NOTE In the case of a harmonised supporting standard for materials, presumption of conformity to the ESRs is limited to technical data of materials in the standard and does not presume adequacy of the material to a specific item of equipment. Consequently it is essential that the technical data stated in the material standard be assessed against the design requirements of this specific item of equipment to verify that the ESRs of the PED are satisfied.
- Standard145 pagesEnglish languagesale 10% offe-Library read for×1 day
- Draft149 pagesEnglish languagesale 10% offe-Library read for×1 day
1.1 This Part of EN 10253 specifies the technical delivery requirements for seamless and welded butt-welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of austenitic and austenitic-ferritic (duplex) stainless steel which are applied for pressure and corrosion resisting purposes at room temperature, at low temperature or at elevated temperatures.
It specifies:
- the type of fittings;
- type A : Butt-welding fittings with reduced pressure factor;
- type B : Butt-welding fittings for use at full service pressure;
- the steel grades;
- the mechanical properties;
- the dimensions and tolerances;
- the requirements for inspection and testing;
- the inspection documents;
- the marking;
- the handling and packaging.
1.2 Unless otherwise specified in this Part of EN 10253 the general technical delivery requirements in EN 10021 apply.
- Corrigendum3 pagesEnglish languagesale 10% offe-Library read for×1 day
This part of EN 10253 specifies the technical delivery requirements for seamless and welded buttwelding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of austenitic and austenitic - ferritic (duplex) stainless steel without specific inspection requirements. It specifies : - the steel grades ; - the mechanical properties ; - the dimensions and tolerances ; - the requirements for inspection and testing ; - the inspection documents ; - the marking ; - the handling and packaging. Unless otherwise specified in this part of EN 10253 the general technical delivery requirements in EN 10021 shall apply. Limitation of use The allowed pressures and temperatures are the responsibility of the customer according to the state of the art and in application of the safety coefficients in the application regulations, codes and standards. In common, joint coefficient are used in the calculation of the thicknesses of components which include one or several butt welds, other than circumferential : - for equipment subject to random non-destructive testing : 0,85 ; - for equipment not subject to non-destructive testing other than visual inspection : 0,7.
- Standard47 pagesEnglish languagesale 10% offe-Library read for×1 day
1.1 This Part of EN 10253 specifies the technical delivery requirements for seamless and welded butt-welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of austenitic and austenitic-ferritic (duplex) stainless steel which are applied for pressure and corrosion resisting purposes at room temperature, at low temperature or at elevated temperatures.
It specifies:
- the type of fittings;
- type A : Butt-welding fittings with reduced pressure factor;
- type B : Butt-welding fittings for use at full service pressure;
- the steel grades;
- the mechanical properties;
- the dimensions and tolerances;
- the requirements for inspection and testing;
- the inspection documents;
- the marking;
- the handling and packaging.
1.2 Unless otherwise specified in this Part of EN 10253 the general technical delivery requirements in EN 10021 apply.
- Standard97 pagesEnglish languagesale 10% offe-Library read for×1 day
This draft European Standard specifies the technical delivery requirements for seamless and welded butt-welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of austenitic and austenitic-ferritic (duplex) stainless steel in two test-categories which are intended for pressure purposes at room temperature, at low temperature or at elevated temperatures, and for the transmission and distribution of fluids and gases.
It specifies:
a) type of fittings;
1) type A: butt-welding fittings with reduced pressure factor;
2) type B: butt-welding fittings for use at full service pressure;
b) steel grades and their chemical compositions;
c) mechanical properties;
d) dimensions and tolerances;
e) requirements for inspection and testing;
f) inspection documents;
g) marking;
h) protection and packaging.
NOTE In the case of a harmonised supporting standard for materials, presumption of conformity to the ESRs is limited to technical data of materials in the standard and does not presume adequacy of the material to a specific item of equipment. Consequently it is essential that the technical data stated in the material standard be assessed against the design requirements of this specific item of equipment to verify that the ESRs of the PED are satisfied.
- Draft156 pagesEnglish languagesale 10% offe-Library read for×1 day
- 31-Jan-2018
- 23.040.40
- 77.140.20
- 2014/68/EU
- 97/23/EC
- IFEK
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.