77.140.45 - Non-alloyed steels
ICS 77.140.45 Details
Non-alloyed steels
Unlegierte Stahle
Aciers non alliés
Nelegirana jekla
General Information
e-Library Subscription
Create subscription and get permanent access to documents within 77.140.45 - Non-alloyed steels
Currently subscription includes documents marked with .We are working on making all documents available within the subscription.
This document specifies requirements for non-alloy and alloy steels that are intended for cold heading or cold extruding and are delivered as wire rods, wire or bars. It also lists the specific requirements for: — steels not intended for heat treatment, with diameters from 2 mm to 100 mm (see Annex A); — case-hardening steels with diameters from 2 mm to 100 mm (see Annex B); — steels for quenching and tempering, including boron-alloyed steels, with diameters from 2 mm to 100 mm (see Annex C). This document (except Annex A) also applies to the properties of cold-headed or cold-extruded parts which have been subjected to a subsequent heat treatment. NOTE Stainless steels for cold heading and cold extruding are covered by ISO 4954-2.
- Standard56 pagesEnglish languagesale 15% off
This document specifies round and shaped non alloyed steel wire for use in the manufacture of ropes for mine hoisting, man-riding haulage, cableways for the transportation of passengers and other high duty applications. Heavy duty refers to situations where the stresses applied to the rope are either high or vary by a large amount during service.
This document refers to round wires and three types of shaped wire: full lock (Z), half lock (H) and trapezoidal (T).
It does not apply to steel wire taken from manufactured ropes.
This document specifies the following for cold drawn non alloyed steel wire for ropes for high duty applications:
- dimensional tolerances;
- mechanical characteristics;
- requirements relating to the chemical composition of the steel wire;
- conditions to be satisfied by any coating.
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery requirements for bright steel products in the drawn, peeled/turned or additional ground condition and they are intended for mechanical purposes, for example for machine parts. The bright steel products are subdivided into the following steel types: a) non-alloy general engineering steels; b) non-alloy free-cutting steels; c) non-alloy and alloy case-hardening steels; d) non-alloy and alloy steels for quenching and tempering. Bright products of stainless steels are not part of this document, they are covered by ISO 16143-4.
- Standard55 pagesEnglish languagesale 15% off
This document specifies the requirements for hot rolled steel sheet piles in respect of its chemical composition, mechanical properties and conditions of delivery. The products specified are for general, structural and civil engineering works. The types of steel sheet piles covered by this standard are: Z-shaped, U-shaped, straight web, H-shaped with their interlocking bars
- Standard33 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard33 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery requirements for open die forgings, forged bars and products pre-forged and finished in ring rolling mills, manufactured from non-alloy quality and special steels and supplied in the normalized, normalized and tempered, quenched and tempered or annealed condition.
The majority of steels listed in this document, with properties in the quenched and tempered condition up to 160 mm thickness, are identical to steels specified in EN ISO 683-1 and EN ISO 683-2 and more extensive information on hardenability and technological properties is given in these standards.
General information on technical delivery conditions is given in EN 10021.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery requirements for open die forgings, forged bars and products pre-forged and finished in ring rolling mills, manufactured from non-alloy quality and special steels and supplied in the normalized, normalized and tempered, quenched and tempered or annealed condition
The majority of steels listed in this document, with properties in the quenched and tempered condition up to 160 mm thickness, are identical to steels specified in EN 10083-1 and EN 10083-2 and more extensive information on hardenability and technological properties is given in these standards.
General Information on technical delivery conditions is given in EN 10021.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery requirements for seamless and welded butt welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of carbon and alloy steel in two test categories which are intended for pressure purposes at room temperature, at low temperature or at elevated temperatures, and for the transmission and distribution of fluids and gases.
It specifies:
a) type of fittings;
type A: Butt-welding fittings with reduced pressure factor;
type B: Butt-welding fittings for use at full service pressure;
b) steel grades and their chemical compositions;
c) mechanical properties;
d) dimensions and tolerances;
e) requirements for inspection and testing;
f) inspection documents;
g) marking;
h) protection and packaging.
NOTE The selection of the appropriate fitting (material, thickness) is the ultimate responsibility of the manufacturer of the pressure equipment (see European Legislation for Pressure Equipment). In the case of a harmonized supporting standard for materials, presumption of conformity to the ESRs is limited to technical data of materials in the standard and does not presume adequacy of the material to a specific item of equipment. Consequently, it is essential that the technical data stated in the material standard be assessed against the design requirements of this specific item of equipment to verify that the ESRs of the PED are satisfied.
- Standard145 pagesEnglish languagesale 10% offe-Library read for1 day
This part of EN 10264 defines cold drawn non alloy steel wire used for the manufacture of:
- ropes for general applications and lifts;
- ropes for applications for which there is no specific European Standard.
This part of EN 10264 does not apply to steel wire taken from manufactured ropes.
This part of EN 10264 specifies the following for cold drawn non alloy steel wire for ropes for general applications:
- dimensional tolerances;
- mechanical characteristics;
- requirements relating to the chemical composition of the steel wire;
- conditions to be satisfied by any coating.
In addition to the requirements of this part of EN 10264, the requirements of EN 10264-1 also apply.
- Standard16 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies an infrared absorption method after combustion in an induction furnace for
the determination of the low carbon content in unalloyed steel.
The method is applicable to carbon contents between 0,000 3 % (mass fraction) and 0,009 % (mass
fraction).
- Standard20 pagesEnglish languagesale 10% offe-Library read for1 day
This draft European Standard specifies the technical delivery requirements for seamless and welded butt welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of carbon and alloy steel in two test categories which are intended for pressure purposes at room temperature, at low temperature or at elevated temperatures, and for the transmission and distribution of fluids and gases.
It specifies:
a) type of fittings;
1) type A: Butt-welding fittings with reduced pressure factor;
2) type B: Butt-welding fittings for use at full service pressure;
b) steel grades and their chemical compositions;
c) mechanical properties;
d) dimensions and tolerances;
e) requirements for inspection and testing;
f) inspection documents;
g) marking;
h) protection and packaging.
NOTE In the case of a harmonised supporting standard for materials, presumption of conformity to the ESRs is limited to technical data of materials in the standard and does not presume adequacy of the material to a specific item of equipment. Consequently it is essential that the technical data stated in the material standard be assessed against the design requirements of this specific item of equipment to verify that the ESRs of the PED are satisfied.
- Standard145 pagesEnglish languagesale 10% offe-Library read for1 day
This part of this European Standard specifies technical delivery conditions for hot-finished seamless, electric welded and submerged arc welded steel structural hollow sections for mechanical engineering purposes of circular, square, rectangular or elliptical forms.
It applies to hollow sections formed hot, with or without subsequent heat treatment, or formed cold with subsequent heat treatment above 580 °C to obtain equivalent mechanical properties to those obtained in the hot formed product.
NOTE 1 The requirements for tolerances, dimensions and sectional properties are specified in EN 10210-2.
NOTE 2 The attention of users is drawn to the fact that whilst cold formed grades in EN 10219-3 can have equivalent mechanical properties to hot-finished grades in EN 10210-3 the sectional properties of square and rectangular hollow sections in EN 10210-2 and EN 10219-2 are not equivalent.
NOTE 3 A range of material grades is specified in this document and the user should select the grade most appropriate to the intended use and service conditions. The grades and mechanical properties of the finished hollow sections are generally comparable with those in EN 10025-2, EN 10025-3, EN 10025-4, EN 10025-5 and EN 10025-6.
NOTE 4 The requirements for seamless and welded steel structural hollow sections for use in offshore structures are covered in EN 10225.
NOTE 5 Spiral welded hollow sections are to be used with caution in construction of dynamic behaviour (fatigue stress) where up to now, there is insufficient knowledge of their performance.
- Standard43 pagesEnglish languagesale 10% offe-Library read for1 day
This part of this standard specifies the technical delivery conditions for electric welded and submerged arc welded cold formed structural steel hollow sections for mechanical engineering purposes of circular, square, rectangular or elliptical forms and applies to structural hollow sections formed cold without subsequent heat treatment other than the heat treatment of the weld line.
NOTE 1 The requirements for tolerances, dimensions and sectional properties can be found in EN 10219-2.
NOTE 2 The attention of users is drawn to the fact that whilst cold formed grades in EN 10219-3 can have equivalent mechanical properties to hot-finished grades in EN 10210-3 the sectional properties of square and rectangular hollow sections in EN 10219-2 and EN 10210-2 are not equivalent.
NOTE 3 A range of steel grades is specified in this document and the user can select the grade most appropriate to the intended use and service conditions. The grades and mechanical properties, but not the final supply condition of cold formed hollow sections are generally comparable with those in EN 10025-2, EN 10025-3, EN 10025-4, EN 10025-5, EN 10025-6, EN 10149-2 and EN 10149-3.
- Standard43 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard43 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery conditions for flat and long products as well as semi-finished products which are meant for further processing to flat and long products of hot rolled non-alloy quality steels in the grades and qualities given in Tables 1 to 5 (chemical composition) and Tables 6 to 8 (mechanical properties) in the usual delivery conditions as given in 6.3. Three engineering steels are also specified in this document (see Tables 2 and 4) (chemical composition) and Table 7 (mechanical properties). This document does not apply to structural hollow sections (see EN 10210 1 and EN 10219 1) and tubes.
The technical delivery conditions apply to:
- thicknesses ≥ 3 mm and ≤ 150 mm for long products of steel grade S460JR, J0, J2, K2 and S500J0;
- thicknesses ≤ 400 mm for flat products of qualities JR, J0, J2 and K2;
- thicknesses ≤ 250 mm for flat and long products of all other grades and qualities.
The steels specified in this document are not intended to be heat treated except products delivered in the delivery condition +N. Stress relieving is accepted. Products delivered in +N condition can be hot formed and/or normalized after delivery (see Clause 3).
This document foresees that semi-finished products which are to be converted to rolled finished products conforming to this document are the subject of special agreements at the time of the order. The chemical compositions are also agreed to at the time of the order; the values are within the limits of Tables 1 and 2.
For certain grades and product forms suitability for particular applications are specified at the time of the order (see 7.4.2, 7.4.3 and Table 9).
- Standard41 pagesEnglish languagesale 10% offe-Library read for1 day
Part 2 of this document, in addition to Part 1, specifies the technical delivery conditions for flat and long products and semi-finished products which are meant for further processing to flat and long products of hot rolled non-alloy quality steels in the grades and qualities given in Tables 2 to 6 (chemical composition) and Tables 7 to 9 (mechanical properties) in the delivery conditions as given in 6.3. Three engineering steels are also specified in this document (see Tables 3 and 5) (chemical composition) and Table 8 (mechanical properties). This document does not apply to structural hollow sections and tubes (see EN 10210-1 and EN 10219-1).
The technical delivery conditions apply to thicknesses > 3 mm and < 150 mm for long products of steel grade S450J0. The technical delivery conditions apply to thicknesses < 250 mm for flat and long products of all other grades and qualities. In addition for flat products of qualities J2 and K2 the technical conditions apply to thicknesses < 400 mm.
Products made of steel grades S185, E295, E335 and E360 cannot be CE marked.
The steels specified in this Part 2 are not intended to be heat treated except products delivered in delivery condition +N. Stress relief annealing is permitted (see also the NOTE in 7.3.1.1 of EN 10025-1:2004). Products delivered in +N condition can be hot formed and/or normalized after delivery (see Clause 3).
NOTE 1 Semi-finished products which are to be converted to rolled finished products conforming to this document should be the subject of special agreement at the time of the enquiry and order. The chemical composition can also be agreed at the time of the order, however the values should be within the limits of Tables 2 and 3.
NOTE 2 For certain grades and product forms suitability for particular applications may be specified at the time of the enquiry and order (see 7.4.2, 7.4.3 and Table 10).
- Standard41 pagesEnglish languagesale 10% offe-Library read for1 day
This part of prEN 10219 specifies tolerances for cold formed welded circular, square, rectangular and elliptical structural hollow sections, manufactured in wall thicknesses up to 40 mm, in the following size ranges:
Circular: Outside diameters up to 2 500 mm
Square: Outside dimensions up to 500 mm x 500 mm
Rectangular: Outside dimensions up to 500 mm x 300 mm
Elliptical: Outside dimensions up to 480 mm x 240 mm
The formulae for calculating sectional properties of sections manufactured to the dimensional tolerances of this standard, to be used for the purposes of structural design, are given in Annex B.
Dimensions and sectional properties for a limited range of more common sizes are given in Annex C.
The general conditions are specified in prEN 10219-1 (product characteristics, test methods and performance criteria that apply under the Construction Products Regulations) and the technical delivery conditions in prEN 10219-2.
NOTE The designation of the sections' major axis (yy) and its minor axis (zz) align with the axis designation used for structural design in the structural Eurocodes.
- Standard44 pagesEnglish languagesale 10% offe-Library read for1 day
This part of prEN 10210 specifies tolerances for hot finished circular, square, rectangular and elliptical structural hollow sections, manufactured in wall thicknesses up to 120 mm, in the following size ranges:
Circular: Outside diameters up to 2 500 mm
Square: Outside dimensions up to 800 mm x 800 mm
Rectangular: Outside dimensions up to 750 mm x 500 mm
Elliptical: Outside dimensions up to 500 mm x 250 mm
The formulae for calculating sectional properties of sections manufactured to the dimensional tolerances of this standard, to be used for the purposes of structural design, are given in Annex A.
Dimensions and sectional properties for a limited range covering the more common sizes are given in Annex B.
The general conditions are specified in prEN 10210-1 (product characteristics, test methods and performance criteria that apply under the Construction Products Regulations) and the technical delivery conditions in prEN 10210-2.
NOTE The designation of the sections' major axis (yy) and its minor axis (zz) align with the axis designation used for structural design in the structural Eurocodes.
- Standard43 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 683-1:2016 specifies the technical delivery requirements for
- semi-finished products, hot formed, e.g. blooms, billets, slabs (see Note 1),
- bars (see Note 1),
- wire rod,
- finished flat products, and
- hammer or drop forgings (see Note 1)
manufactured from the direct hardening non-alloy steels and the non-alloy flame- and induction-hardening steels listed in Table 3 and supplied in one of the heat-treatment conditions given for the different types of products in Table 1 and in one of the surface conditions given in Table 2.
The steels are, in general, intended for the manufacture of quenched and tempered or austempered (see 3.2 and Note 2) and flame- or induction-hardened machine parts (see Tables 9 and 11), but can also be partly used in the normalized condition (see Table 10).
The requirements for mechanical properties given in ISO 683-1:2016 are restricted to the sizes given in Tables 9 and 10.
NOTE 1 Hammer-forged semi-finished products (blooms, billets, slabs, etc.), seamless rolled rings and hammer-forged bars are, in the following, covered under semi-finished products or bars and not under the term "hammer and drop forgings".
NOTE 2 For the purposes of simplification, the term "quenched and tempered" is, unless otherwise indicated, used in the following also for the austempered condition.
NOTE 3 For International Standards relating to steels complying with the requirements for the chemical composition in Table 3, however, supplied in other product forms or treatment conditions than given above or intended for special applications, and for other related International Standards, see the Bibliography.
NOTE 4 ISO 683-1 :2016 does not apply to bright products and bars and wire rod for cold heading. For such products, see ISO 683‑18 and ISO 4954.
In special cases, variations in these technical delivery requirements or additions to them can form the subject of an agreement between the manufacturer and purchaser at the time of enquiry and order (see 5.2 and Annex B).
In addition to ISO 683-1:2016, the general technical delivery requirements of ISO 404 are applicable.
- Standard48 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 683-2:2016 specifies the technical delivery requirements for
- semi-finished products, hot formed, e.g. blooms, billets, slabs (see Note 1),
- bars (see Note 1),
- wire rod,
finished flat products, and
- hammer or drop forgings (see Note 1)
manufactured from the direct hardening alloy steels and the alloy flame- and induction-hardening steels listed in Table 3 and supplied in one of the heat-treatment conditions given for the different types of products in Table 1 and in one of the surface conditions given in Table 2.
The steels are, in general, intended for the manufacture of quenched and tempered or austempered (see 3.2 and Note 2) and flame- or induction-hardened machine parts (see Tables 8 and 9).
The requirements for mechanical properties given in ISO 683-2:2016 are restricted to the sizes given in the relevant Table 8.
NOTE 1 Hammer-forged semi-finished products (blooms, billets, slabs, etc.), seamless rolled rings and hammer-forged bars are in the following covered under semi-finished products or bars and not under the term "hammer and drop forgings".
NOTE 2 For the purposes of simplification, the term "quenched and tempered" is, unless otherwise indicated, used in the following also for the austempered condition.
NOTE 3 For International Standards relating to steels complying with the requirements for the chemical composition in Table 3, however, supplied in other product forms or treatment conditions than given above or intended for special applications, and for other related International Standards, see the Bibliography.
NOTE 4 ISO 683-2 :2016 does not apply to bright products and bars and wire rod for cold heading. For such products, see ISO 683‑18 and ISO 4954.
In special cases, variations in these technical delivery requirements or additions to them can form the subject of an agreement at the time of enquiry and order (see 5.2 and Annex B).
In addition to ISO 683-2:2016, the general technical delivery requirements of ISO 404 are applicable.
- Standard49 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 683-1:2016 specifies the technical delivery requirements for
- semi-finished products, hot formed, e.g. blooms, billets, slabs (see Note 1),
- bars (see Note 1),
- wire rod,
- finished flat products, and
- hammer or drop forgings (see Note 1)
manufactured from the direct hardening non-alloy steels and the non-alloy flame- and induction-hardening steels listed in Table 3 and supplied in one of the heat-treatment conditions given for the different types of products in Table 1 and in one of the surface conditions given in Table 2.
The steels are, in general, intended for the manufacture of quenched and tempered or austempered (see 3.2 and Note 2) and flame- or induction-hardened machine parts (see Tables 9 and 11), but can also be partly used in the normalized condition (see Table 10).
The requirements for mechanical properties given in ISO 683-1:2016 are restricted to the sizes given in Tables 9 and 10.
NOTE 1 Hammer-forged semi-finished products (blooms, billets, slabs, etc.), seamless rolled rings and hammer-forged bars are, in the following, covered under semi-finished products or bars and not under the term "hammer and drop forgings".
NOTE 2 For the purposes of simplification, the term "quenched and tempered" is, unless otherwise indicated, used in the following also for the austempered condition.
NOTE 3 For International Standards relating to steels complying with the requirements for the chemical composition in Table 3, however, supplied in other product forms or treatment conditions than given above or intended for special applications, and for other related International Standards, see the Bibliography.
NOTE 4 ISO 683-1 :2016 does not apply to bright products and bars and wire rod for cold heading. For such products, see ISO 683‑18 and ISO 4954.
In special cases, variations in these technical delivery requirements or additions to them can form the subject of an agreement between the manufacturer and purchaser at the time of enquiry and order (see 5.2 and Annex B).
In addition to ISO 683-1:2016, the general technical delivery requirements of ISO 404 are applicable.
- Standard48 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 683-2:2016 specifies the technical delivery requirements for - semi-finished products, hot formed, e.g. blooms, billets, slabs (see Note 1), - bars (see Note 1), - wire rod, finished flat products, and - hammer or drop forgings (see Note 1) manufactured from the direct hardening alloy steels and the alloy flame- and induction-hardening steels listed in Table 3 and supplied in one of the heat-treatment conditions given for the different types of products in Table 1 and in one of the surface conditions given in Table 2. The steels are, in general, intended for the manufacture of quenched and tempered or austempered (see 3.2 and Note 2) and flame- or induction-hardened machine parts (see Tables 8 and 9). The requirements for mechanical properties given in ISO 683-2:2016 are restricted to the sizes given in the relevant Table 8. NOTE 1 Hammer-forged semi-finished products (blooms, billets, slabs, etc.), seamless rolled rings and hammer-forged bars are in the following covered under semi-finished products or bars and not under the term "hammer and drop forgings". NOTE 2 For the purposes of simplification, the term "quenched and tempered" is, unless otherwise indicated, used in the following also for the austempered condition. NOTE 3 For International Standards relating to steels complying with the requirements for the chemical composition in Table 3, however, supplied in other product forms or treatment conditions than given above or intended for special applications, and for other related International Standards, see the Bibliography. NOTE 4 ISO 683-2 :2016 does not apply to bright products and bars and wire rod for cold heading. For such products, see ISO 683‑18 and ISO 4954. In special cases, variations in these technical delivery requirements or additions to them can form the subject of an agreement at the time of enquiry and order (see 5.2 and Annex B). In addition to ISO 683-2:2016, the general technical delivery requirements of ISO 404 are applicable.
- Standard40 pagesEnglish languagesale 15% off
- Standard40 pagesEnglish languagesale 15% off
- Standard40 pagesEnglish languagesale 15% off
- Standard40 pagesFrench languagesale 15% off
- Standard40 pagesFrench languagesale 15% off
ISO 683-1:2016 specifies the technical delivery requirements for - semi-finished products, hot formed, e.g. blooms, billets, slabs (see Note 1), - bars (see Note 1), - wire rod, - finished flat products, and - hammer or drop forgings (see Note 1) manufactured from the direct hardening non-alloy steels and the non-alloy flame- and induction-hardening steels listed in Table 3 and supplied in one of the heat-treatment conditions given for the different types of products in Table 1 and in one of the surface conditions given in Table 2. The steels are, in general, intended for the manufacture of quenched and tempered or austempered (see 3.2 and Note 2) and flame- or induction-hardened machine parts (see Tables 9 and 11), but can also be partly used in the normalized condition (see Table 10). The requirements for mechanical properties given in ISO 683-1:2016 are restricted to the sizes given in Tables 9 and 10. NOTE 1 Hammer-forged semi-finished products (blooms, billets, slabs, etc.), seamless rolled rings and hammer-forged bars are, in the following, covered under semi-finished products or bars and not under the term "hammer and drop forgings". NOTE 2 For the purposes of simplification, the term "quenched and tempered" is, unless otherwise indicated, used in the following also for the austempered condition. NOTE 3 For International Standards relating to steels complying with the requirements for the chemical composition in Table 3, however, supplied in other product forms or treatment conditions than given above or intended for special applications, and for other related International Standards, see the Bibliography. NOTE 4 ISO 683-1 :2016 does not apply to bright products and bars and wire rod for cold heading. For such products, see ISO 683‑18 and ISO 4954. In special cases, variations in these technical delivery requirements or additions to them can form the subject of an agreement between the manufacturer and purchaser at the time of enquiry and order (see 5.2 and Annex B). In addition to ISO 683-1:2016, the general technical delivery requirements of ISO 404 are applicable.
- Standard39 pagesEnglish languagesale 15% off
- Standard39 pagesEnglish languagesale 15% off
- Standard39 pagesEnglish languagesale 15% off
- Standard41 pagesFrench languagesale 15% off
- Standard41 pagesFrench languagesale 15% off
This European Standard specifies an inductively coupled plasma optical emission spectrometry routine method for the analysis of unalloyed and low alloyed steels, whose iron content shall be at least 95 %.
This method is applicable to the elements listed in Table 1 within the ranges shown.
Table 1 - Application ranges
(...)
In all cases, the ranges specified can be extended or adapted (after validation) for the determination of other mass fractions, provided that the iron content in the samples under concern is above 95 %.
Other elements may be included. However such elements and their mass fractions should be carefully checked, taking into account the possible interferences, the sensitivity, the resolution and the linearity criteria of each instrument and each wavelength.
Depending also on the sensitivity of each instrument, suitable dilutions of the calibration and the test sample solutions may be necessary.
Moreover, even if the method described is "multi elemental", it is not absolutely necessary to carry out the determination of all the elements of its scope simultaneously: the measurement conditions have to be optimised by each laboratory, depending on the performances of each apparatus available.
NOTE 1 The accuracy of the method is unsatisfactory for phosphorus contents from 0,05 to 0,1 %.
NOTE 2 The trueness of the method couldn't be checked for vanadium contents below 0,05 %.
NOTE 3 The precision of the method is unsatisfactory for aluminium (total) contents below 0,02 %.
- Standard44 pagesEnglish languagesale 10% offe-Library read for1 day
This part of ISO 15614 specifies how a preliminary welding procedure specification (pWPS) for production and repair welding of non-alloyed and low-alloyed cast irons is qualified by fusion welding procedure tests. This part of ISO 15614 defines the conditions for execution of the welding procedure tests and the range of qualification for welding procedures for all practical welding operations within the range of a defined list of variables. This part of ISO 15614 is applicable to all new welding procedures. However, it does not invalidate previous welding procedure tests made to former national standards or specifications. Where additional tests have to be carried out to make the qualification technically equivalent, it is only necessary to do the additional tests on a test piece made in accordance with this part of ISO 15614. Additional tests may be required by application standards.
- Standard25 pagesEnglish languagesale 10% offe-Library read for1 day
This part of this European Standard specifies the technical delivery conditions for cold formed welded structural hollow sections of circular, square or rectangular forms and applies to structural hollow sections formed cold without subsequent heat treatment.
Requirements for tolerances, dimensions and sectional properties are contained in EN 10219-2.
NOTE A range of steel grades is specified in this European Standard and the user should select the grade appropriate to the intended use and service conditions. The grades and mechanical properties of the finished hollow sections are compatible with those in EN 10025-2 and EN 10025-3.
- Standard35 pagesEnglish languagesale 10% offe-Library read for1 day
This part of this European Standard specifies technical delivery conditions for hot finished hollow sections of circular, square, rectangular or elliptical forms and applies to hollow sections formed hot, with or without subsequent heat treatment, or formed cold with subsequent heat treatment to obtain equivalent metallurgical conditions to those obtained in the hot formed product.
Requirements for tolerances, dimensions and sectional properties are contained in EN 10210-2.
NOTE A range of material grades is specified in this standard and the user should select the grade appropriate to the intended use and service conditions. The grades and mechanical properties of the finished hollow sections are compatible with those in EN 10025-2 and EN 10025-3.
- Standard38 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies requirements for steel butt-welding fittings (elbows and return bends, concentric and eccentric reducers, equal and reducing tees, dished ends and caps) made of wrought carbon steel and delivered without specific inspection. The fittings described in this European Standard do not fulfil specific design requirements; consequently they cannot be considered as conforming to the Essential Requirements of the Pressure Equipment Directive (Directive 97/23/EC of 29.05.1997).
- Standard33 pagesEnglish languagesale 10% offe-Library read for1 day
This part of this European Standard specifies the tolerances on dimensions, squareness of ends, straightness and mass of cold formed non alloy steel sheet piles which are defined in EN 10249-1.
- Standard8 pagesEnglish languagesale 10% offe-Library read for1 day
This part of this European Standard specifies the requirements for cold formed non alloy steel sheet piling produced from hot rolled strip or sheet with a thickness equal to or greater than 2mm in respect of its chemical composition, mechanical and technological properties and delivery conditions. The products specified are for general, structural and civil engineering works. Requirements concerning the tolerances on shape and dimensions are specified in Part 2 of this European Standard.
- Standard11 pagesEnglish languagesale 10% offe-Library read for1 day
This part of this European standard specifies the tolerances on dimensions, squareness of ends, straightness and mass of hot rolled non alloy steel sheet piles which are defined in EN 10248-1.
- Standard12 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery requirements for bright steel products in the drawn, peeled/turned or additional ground condition and they are intended for mechanical purposes, for example for machine parts.
- Draft60 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery requirements for seamless and welded butt welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of carbon and alloy steel in two test categories which are intended for pressure purposes at room temperature, at low temperature or at elevated temperatures, and for the transmission and distribution of fluids and gases.
It specifies:
a) type of fittings;
type A: Butt-welding fittings with reduced pressure factor;
type B: Butt-welding fittings for use at full service pressure;
b) steel grades and their chemical compositions;
c) mechanical properties;
d) dimensions and tolerances;
e) requirements for inspection and testing;
f) inspection documents;
g) marking;
h) protection and packaging.
NOTE The selection of the appropriate fitting (material, thickness) is the ultimate responsibility of the manufacturer of the pressure equipment (see European Legislation for Pressure Equipment). In the case of a harmonized supporting standard for materials, presumption of conformity to the ESRs is limited to technical data of materials in the standard and does not presume adequacy of the material to a specific item of equipment. Consequently, it is essential that the technical data stated in the material standard be assessed against the design requirements of this specific item of equipment to verify that the ESRs of the PED are satisfied.
- Draft17 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery requirements for bright steel products in the drawn, peeled/turned or additional ground condition and they are intended for mechanical purposes, for example for machine parts.
- Draft60 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the technical delivery requirements for seamless and welded butt welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of carbon and alloy steel in two test categories which are intended for pressure purposes at room temperature, at low temperature or at elevated temperatures, and for the transmission and distribution of fluids and gases.
It specifies:
a) type of fittings;
type A: Butt-welding fittings with reduced pressure factor;
type B: Butt-welding fittings for use at full service pressure;
b) steel grades and their chemical compositions;
c) mechanical properties;
d) dimensions and tolerances;
e) requirements for inspection and testing;
f) inspection documents;
g) marking;
h) protection and packaging.
NOTE The selection of the appropriate fitting (material, thickness) is the ultimate responsibility of the manufacturer of the pressure equipment (see European Legislation for Pressure Equipment). In the case of a harmonized supporting standard for materials, presumption of conformity to the ESRs is limited to technical data of materials in the standard and does not presume adequacy of the material to a specific item of equipment. Consequently, it is essential that the technical data stated in the material standard be assessed against the design requirements of this specific item of equipment to verify that the ESRs of the PED are satisfied.
- Draft17 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for cold formed steel sheet piles produced from hot rolled strip or sheet with a thickness equal to or greater than 3 mm in respect of its chemical composition, mechanical properties and conditions of delivery.
The products specified are for general, structural and civil engineering works. The types of steel sheet piles covered by this document are: Z-shaped, Omega-shaped and trench sheets. The requirements in respect of tolerances on shape and dimensions are specified in Part 2 of this document.
- Draft20 pagesEnglish languagesale 10% offe-Library read for1 day
This part of prEN 10219 specifies the technical delivery conditions for electric welded and submerged arc welded cold formed structural steel hollow sections of circular, square, rectangular or elliptical forms and applies to structural hollow sections formed cold without subsequent heat treatment.
The general conditions (product characteristics, test methods and performance criteria that apply under the Construction Products Regulations) are specified in prEN 10219-1 and the requirements for tolerances, dimensions and sectional properties in prEN 10219-3.
NOTE 1 prEN 10219-1 covers provision of the Construction Products Regulations (CPR) to fulfil European law for construction products. The technical delivery conditions are described within prEN 10219-2 in combination with Clauses 2, 3, 4, 5, 7 and 8 of prEN 10219-1.
NOTE 2 The attention of users is drawn to the fact that whilst cold formed grades in prEN 10219-2 can have equivalent mechanical properties to hot-finished grades in prEN 10210-2 the sectional properties of square and rectangular hollow sections in prEN 10219-3 and prEN 10210-3 are not equivalent.
NOTE 3 A range of steel grades is specified in this European Standard and the user should select the grade most appropriate to the intended use and service conditions. The grades and mechanical properties, but not the final supply condition of cold formed hollow sections are comparable with those in EN 10025-2, EN 10025-3, EN 10025-4, EN 10025-5, EN 10025-6, EN 10149-2 and EN 10149-3.
NOTE 4 Hollow sections for offshore structures are covered in EN 10225.
- Draft39 pagesEnglish languagesale 10% offe-Library read for1 day
This part of prEN 10219 specifies the product characteristics, test methods and performance criteria for electric welded and submerged arc welded cold formed structural steel hollow sections of circular, square, rectangular or elliptical forms, produced without any subsequent heat treatment other than the heat treatment of the weld line.
Requirements for the technical delivery conditions are specified in prEN 10219-2 and for tolerances, dimensions and sectional properties in prEN 10219-3.
NOTE 1 prEN 10219-1 covers provision of the Construction Products Regulations (CPR) to fulfil European law for construction products. The technical delivery conditions are described within prEN 10219-2 in combination with Clauses 2, 3, 4, 5, 7 and 8 of prEN 10219-1.
NOTE 2 Hollow sections for offshore structures are covered in EN 10225.
- Draft20 pagesEnglish languagesale 10% offe-Library read for1 day
This part of prEN 10210 specifies the product characteristics, test methods and performance criteria for hot-finished seamless, electric welded and submerged arc welded steel structural hollow sections of circular, square, rectangular or elliptical forms.
It applies to hollow sections formed hot, with or without subsequent heat treatment, or formed cold with subsequent heat treatment above 580 °C to obtain equivalent mechanical conditions to those obtained in the hot formed product.
Requirements for the technical delivery conditions are specified in prEN 10210-2 and for tolerances, dimensions and sectional properties in prEN 10210-3.
NOTE 1 prEN 10210-1 covers provision of the Construction Products Regulations (CPR) to fulfil European law for construction products. The technical delivery conditions are described within prEN 10210-2 in combination with Clauses 2, 3, 4, 5, 7 and 8 of prEN 10210-1.
NOTE 2 Seamless and welded hollow sections for offshore structures are covered in EN 10225.
- Draft20 pagesEnglish languagesale 10% offe-Library read for1 day
This part of this European Standard specifies technical delivery conditions for hot-finished seamless, electric welded and submerged arc welded steel structural hollow sections of circular, square, rectangular or elliptical forms.
It applies to hollow sections formed hot, with or without subsequent heat treatment, or formed cold with subsequent heat treatment above 580 °C to obtain equivalent mechanical conditions to those obtained in the hot formed product.
The general conditions (product characteristics, test methods and performance criteria that apply under the Construction Products Regulations) are specified in prEN 10210-1 and the requirements for tolerances, dimensions and sectional properties in prEN 10210-3.
NOTE 1 prEN 10210-1 covers provision of the Construction Products Regulations (CPR) to fulfil European law for construction products. The technical delivery conditions are described within prEN 10210-2 in combination with Clauses 2, 3, 4, 5, 7 and 8 of prEN 10210-1.
NOTE 2 The attention of users is drawn to the fact that whilst cold formed grades in prEN 10219-2 can have equivalent mechanical properties to hot-finished grades in prEN 10210-2 the sectional properties of square and rectangular hollow sections in prEN 10210-3 and prEN 10219-3 are not equivalent.
NOTE 3 A range of material grades is specified in this standard and the user should select the grade most appropriate to the intended use and service conditions. The grades and mechanical properties of the finished hollow sections are comparable with those in EN 10025-2, EN 10025-3, EN 10025-4, EN 10025-5 and EN 10025-6.
NOTE 4 Seamless and welded hollow sections for offshore structures are covered in EN 10225.
- Draft42 pagesEnglish languagesale 10% offe-Library read for1 day
This part of this European Standard specifies the tolerances on dimensions, squareness of ends, straightness and mass of hot rolled non alloy steel sheet piling which are defined in EN 10248-1.
- Draft22 pagesEnglish languagesale 10% offe-Library read for1 day
This part of this European Standard specifies the requirements for hot rolled non alloy steel sheet piling in respect of its chemical composition, mechanical properties and conditions of delivery.The products specified are for general, structural and civil engineering works.Requirements in respect of tolerances on shape and dimensions are specified in Part 2 of this European Standard.
- Draft38 pagesEnglish languagesale 10% offe-Library read for1 day
This part of this European Standard specifies the requirements for cold formed non alloy steel sheet piling produced from hot rolled strip or sheet with a thickness equal to oe greater than 2 mm in respect of its chemical composition, mechanical and technological properties and delivery conditions.The products specified are for general, structural and civil engineering works.Requirements in respect of tolerances on shape and dimensions are specified in Part 2 of this European Standard.
- Draft26 pagesEnglish languagesale 10% offe-Library read for1 day
This part of this European Standard specifies the tolerances on dimensions, squareness of ends, straightness and mass of cold-formed non alloy steel sheet piling which are defined in EN 10249-1.
- Draft10 pagesEnglish languagesale 10% offe-Library read for1 day
This part of this European Standard specifies round and shaped non alloyed steel wire for use in the manufacture of ropes for mine hoisting, man-riding haulage, cableways for the transportation of passengers and other high duty applications. This part of this European Standard refers to round wires and three types of shaped wire: full lock (Z), half lock (H) and trapezoidal (T). In addition to the requirements of this part of this European Standard, the requirements of EN 10264-1 also apply. It does not apply to steel wire taken from manufactured ropes. This part of this European Standard specifies the following for cold drawn non alloyed steel wire for ropes for high duty applications:
- dimensional tolerances;
- mechanical characteristics;
- requirements relating to the chemical composition of the steel wire;
- conditions to be satisfied by any coating.
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day
This part of this European standard specifies the requirements for hot rolled non alloy steel sheet piling in respect of its chemical composition, mechanical properties and conditions of delivery. The products specified are for general, structural and civil engineering works. Requirements in respect of tolerances onshape and dimensions are specified in Part 2 of this European Standard.
- Standard15 pagesEnglish languagesale 10% offe-Library read for1 day
This Part of this European Standard specifies the technical delivery requirements for open die forgings, forged bars and products pre-forged and finished in ring rolling mills, manufactured from non-alloy quality and special steels and supplied in the normalized, normalized and tempered, quenched and tempered or annealed condition.
- Standard11 pagesEnglish languagesale 10% offe-Library read for1 day
This part of this European Standard defines cold drawn non alloy steel wire used for the manufacture of: ⎯ Ropes for general applications and lifts; ⎯ Ropes for applications for which there is no specific EN standard. This part of this standard does not apply to steel wire taken from manufactured ropes. This part of this European standard specifies the following for cold drawn non alloy steel wire for ropes for general applications:
- dimensional tolerances;
- mechanical characteristics;
- requirements relating to the chemical composition of the steel wire;
- conditions to be satisfied by any coating. In addition to the requirements of this part of this European standard, the requirements of EN 10264-1 also apply.
- Standard10 pagesEnglish languagesale 10% offe-Library read for1 day
1.1 This Part of EN 10253 specifies the technical delivery requirements for seamless and welded butt welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of carbon and alloy steel which are intended for pressure purposes at room temperature, at low temperature or at elevated temperatures, and for the transmission and distribution of fluids and gases.
It specifies :
- the type of fittings ;
- type A : Butt-welding fittings with reduced pressure factor ;
- type B : Butt-welding fittings for use at full service pressure ;
- the steel grades ;
- the mechanical properties ;
- the dimensions and tolerances ;
- the requirements for inspection and testing ;
- the inspection documents ;
- the marking ;
- the protection and packaging.
- Standard125 pagesEnglish languagesale 10% offe-Library read for1 day
- Standard17 pagesEnglish languagesale 10% offe-Library read for1 day
This Part of EN 10253 specifies the technical delivery requirements for seamless and welded butt welding fittings (elbows, concentric and eccentric reducers, equal and reducing tees, caps) made of carbon and alloy steel which are intended for pressure purposes at room temperature, at low temperature or at elevated temperatures, and for the transmission and distribution of fluids and gases.
It specifies:
- type of fittings ;
- type A : Butt-welding fittings with reduced pressure factor ;
- type B : Butt-welding fittings for use at full service pressure ;
- steel grades ;
- mechanical properties ;
- dimensions and tolerances ;
- requirements for inspection and testing ;
- inspection documents ;
- marking ;
- protection and packaging.
NOTE In the case of a harmonised supporting standard for materials, presumption of conformity to the ESRs is limited to technical data of materials in the standard and does not presume adequacy of the material to a specific item of equipment. Consequently it is essential that the technical data stated in the material standard be assessed against the design requirements of this specific item of equipment to verify that the ESRs of the PED are satisfied.
- Standard125 pagesEnglish languagesale 10% offe-Library read for1 day
DIN - Corrected Tables 7, 8, 12 and 13
- Corrigendum5 pagesGerman languagesale 10% offe-Library read for1 day