iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 12167:1999

(Main)

Copper and copper alloys - Profiles and rectangular bar for general purposes

Copper and copper alloys - Profiles and rectangular bar for general purposes

This European Standard specifies the composition, property requirements and dimensional tolerances for copper and copper alloy profiles and rectangular bars supplied in straight lengths. This standard applies to rectangular bar with thicknesses from 3 mm up to and including 60 mm and with widths from 6 mm up to and including 120 mm. The sampling procedures, the methods of test for verification of conformity to the requirements of this standard, and the delivery conditions are also specified.

Kupfer und Kupferlegierungen - Profile und Rechteckstangen zur allgemeinen Verwendung

Diese Europäische Norm legt die Zusammensetzung, die Anforderungen an die Eigenschaften und die Grenzabmaße für Profile und Rechteckstangen aus Kupfer und Kupferlegierungen in geraden Längen fest. Diese Norm gilt für Rechteckstangen mit Dicken von 3 mm bis 60 mm und Breiten von 6 mm bis 120 mm. Der Ablauf der Probenentnahme, die Prüfverfahren zur Feststellung der Übereinstimmung mit den Anforderungen dieser Norm und die Lieferbedingungen sind ebenfalls festgelegt.

Cuivre et alliages de cuivre - Profilés et barres rectangulaires pour usages généraux

La présente norme européenne spécifie la composition, les caractéristiques et les tolérances dimensionnelles des profilés et des barres rectangulaires en cuivre et alliages de cuivre livrés en longueurs droites. La présente norme s'applique aux barres rectangulaires d'épaisseurs allant de 3 mm a 60 mm compris et de largeurs allant de 6 mm a 120 mm compris. Les procédures d'échantillonnage, les méthodes d'essai pour la vérification de la conformité aux prescriptions de la présente norme et les conditions de livraisons sont également spécifiées.

Baker in bakrove zlitine - Profili in palice s pravokotnim prerezom za splošno uporabo

General Information

Status
Withdrawn
Publication Date
31-Oct-1999
Withdrawal Date
12-Sep-2011
ICS
77.150.30 - Copper products
Technical Committee
INEK - Nonferrous metals
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
06-Sep-2011
Due Date
29-Sep-2011
Completion Date
13-Sep-2011
Ref Project
EN 12167:1998 - Copper and copper alloys - Profiles and rectangular bar for general purposes

Relations

Replaced By
SIST EN 12167:2011 - Copper and copper alloys - Profiles and bars for general purposes
Effective Date
01-Oct-2011

Buy Standard

EN 12167:1999EN 12167:1999
PreviousNext
Standard
EN 12167:1999
English language
43 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Baker in bakrove zlitine - Profili in palice s pravokotnim prerezom za splošno uporaboKupfer und Kupferlegierungen - Profile und Rechteckstangen zur allgemeinen VerwendungCuivre et alliages de cuivre - Profilés et barres rectangulaires pour usages générauxCopper and copper alloys - Profiles and rectangular bar for general purposes77.150.30Bakreni izdelkiCopper productsICS:Ta slovenski standard je istoveten z:EN 12167:1998SIST EN 12167:1999en01-november-1999SIST EN 12167:1999SLOVENSKI
STANDARD



SIST EN 12167:1999



SIST EN 12167:1999



SIST EN 12167:1999



SIST EN 12167:1999



SIST EN 12167:1999



SIST EN 12167:1999



SIST EN 12167:1999



SIST EN 12167:1999



S
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 12449:2023(Main)
Copper and copper alloys - Seamless, round tubes for general purposes
EN 12449:2023

This European Standard specifies the composition, property requirements and tolerances on dimensions and form for seamless round drawn copper and copper alloy tubes for general purposes supplied in the size range from 3 mm up to and including 450 mm outside diameter and from 0,3 mm up to and including 20 mm wall thickness.
The sampling procedures and the methods of test for verification of conformity to the requirements of this European Standard are also specified.
NOTE   Tubes having an outside diameter less than 80 mm and/or a wall thickness greater than 2 mm in certain alloys are most frequently used for free machining purposes which are specified in EN 12168.

  • Standard
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1978:2022(Main)
Copper and copper alloys - Copper cathodes
EN 1978:2022

This document specifies the composition and property requirements for cathodes of two copper grades, designated Cu-CATH-1 (CR001A) and Cu-CATH-2 (CR002A).
Annex A (normative) describes methods for sampling cathodes for use in cases of dispute between the purchaser and the supplier. Annex B (informative) gives information on the relationships between electrical resistivity and conductivity of copper.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13601:2021(Main)
Copper and copper alloys - Copper rod, bar and wire for general electrical purposes
EN 13601:2021

This European Standard specifies the composition, property requirements including electrical properties, and tolerances on dimensions and form for copper rod, bar and wire for general electrical purposes. Cross sections and size ranges are:
-   round, square and hexagonal rod with diameters or widths across flats from 2 mm up to and including 160 mm;
-   bar with thicknesses from 2 mm up to and including 40 mm and widths from 3 mm up to and including 250 mm;
-   round, square, hexagonal and rectangular wire with diameters or widths across flats from 2 mm up to and including 25 mm, as well as thicknesses from 0,5 mm up to and including 12 mm with widths from 1 mm up to and including 250 mm.
The sampling procedures and test methods for verification of conformity to the requirements of this standard are also specified.
NOTE   Drawn, round copper wire - plain or tinned, single or multiline - for the manufacture of electrical conductors is specified in EN 13602.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13603:2021(Main)
Copper and copper alloys - Test methods for assessing protective tin coatings on drawn round copper wire for electrical purposes
EN 13603:2021

This European Standard specifies methods for assessing the tin coating on drawn round copper wire for the manufacture of electrical conductors, e.g. according to EN 13602.
This European Standard includes test methods for the determination of the following characteristics:
a)   thickness of the unalloyed tin coating;
b)   continuity of the tin coating;
c)   adherence of the tin coating.
WARNING - This European Standard can involve the use of hazardous materials, operations, and equipment. This standard does not purport to address all of the safety problems associated with their use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 13605:2021(Main)
Copper and copper alloys - Copper profiles and profiled wire for electrical purposes
EN 13605:2021

This European Standard specifies the composition, property requirements including electrical properties, and tolerances on dimensions and form for copper profiles and profiled wire for electrical purposes, which would fit within a circumscribing circle of maximum 180 mm diameter.
The sampling procedures, the test methods for verification of conformity to the requirements of this standard, and the delivery conditions are also specified.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1254-8:2021(Main)
Copper and copper alloys - Plumbing fittings - Part 8: Press fittings for use with plastics and multilayer pipes
EN 1254-8:2021

This document specifies product characteristics, assessment methods, compliance criteria and a designation system for fittings with radial and axial press ends for use with plastics and multilayer pipes. The fitting ends have a size range from 10 mm to 160 mm. The fittings are designed for a service lifetime up to fifty.
This document applies to copper alloy fittings. A non-exhaustive list of these copper alloys is given in CEN/TS 13388.
Adaptor fittings for use with plastic and multilayer pipes may combine press ends with fitting ends defined in the other parts of EN 1254.
Press fittings for use with plastic and multilayer pipes may also have flanged end connections according to EN 1092-3.
Press fittings for use with plastic and multilayer pipes may also have a plated or other decorative surface coating.
Fittings can be produced by machining, metal forming, casting, or fabrication.
Products covered by this standard are intended to be used in:
a)   liquid applications:
-   hot, cold or combined hot and cold water systems according to EN 806;
-   closed heating systems according to EN 12828 and cooling systems;
-   drainage systems;
-   sprinkler systems according to EN 12845;
b)   gas applications:
-   natural gas and liquefied petroleum gas systems with a maximum operating pressure less than or equal to 5 bar according to EN 1775;
-   compressed air systems.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1254-4:2021(Main)
Copper and copper alloys - Plumbing fittings - Part 4: Threaded fittings
EN 1254-4:2021

This document specifies product characteristics, assessment methods, compliance criteria and a designation system for threaded fittings. These threaded ends exist with metallic and with non-metallic sealing elements for the purposes of joining with tubes, pipes, fittings or valves, the threaded ends have a size range from 3,175 mm (1/8") to 101,6 mm (4"). The threaded fittings are designed for a service lifetime up to fifty years.
The fittings are used up to the operating temperatures and maximum operating pressures as indicated in Annex A.
This document applies to copper alloy fittings. A non-exhaustive list of these copper alloys is given in CEN/TS 13388.
Threaded fittings may also have flanged end connections according to EN 1092-3.
Threaded fittings may also have a plated or other decorative surface coating.
Fittings can be produced by machining, metal forming, casting, or fabrication.
Products covered by this document are intended to be used in:
a)   liquid applications:
-   hot, cold or combined hot and cold water systems according to EN 806;
-   closed heating systems according to EN 12828 and cooling systems;
-   drainage systems;
-   sprinkler systems according to EN 12845.
b)   gas applications:
-   natural gas and liquefied petroleum gas systems with a maximum operating pressure less than or equal to 5 bar according to EN 1775;
-   compressed air systems.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1254-2:2021(Main)
Copper and copper alloys - Plumbing fittings - Part 2: Compression fittings for use with copper tubes
EN 1254-2:2021

This document specifies product characteristics, assessment methods, compliance criteria of the test results and a designation system for compression fittings for connecting with copper tubes. Compression fittings exist with sealing elements - metallic and/or non-metallic - called non manipulative (commonly referenced as type A) and without sealing elements, called manipulative (commonly referenced as type B). For the purposes of joining copper tubes, the fitting ends have a size range from 6 mm to 108 mm. The compression fittings are designed for a service lifetime up to fifty years.
The fittings are used up to the operating temperatures and maximum operating pressures as indicated in Annex A.
This document applies to copper alloy fittings. A non-exhaustive list of these copper alloys is given in CEN/TS 13388.
Compression fitting ends, Type A, are used with copper tubes to EN 1057 in all material hardness conditions.
NOTE 1   Compression fittings, Type A, will possibly require an internal support when used with R220 (annealed) copper tube and the manufacturer’s advice should be sought.
Compression fitting ends, Type B, are used with R220 (annealed) or R250 (half-hard) copper tube to EN 1057.
NOTE 2   Compression fittings, Type B, may be used with R290 (hard) copper tube and the manufacturer’s advice should be sought.
Adaptor fittings for use with copper tubes may combine compression ends with fitting ends defined in the other parts of EN 1254.
Compression fittings for use with copper tubes may also have flanged end connections according to EN 1092-3.
Compression fittings for use with copper tubes may also have a plated or other decorative surface coating.
Fittings can be produced by machining, metal forming, casting, or fabrication.
Products covered by this standard are intended to be used in:
a)   liquid applications:
-   hot, cold or combined hot and cold water systems according to EN 806;
-   closed heating systems according to EN 12828 and cooling systems;
-   drainage systems;
-   sprinkler systems according to EN 12845.
b)   gas applications:
-   natural gas and liquefied petroleum gas systems with a maximum operating pressure less than or equal to 5 bar according to EN 1775;
-   compressed air systems.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1254-3:2021(Main)
Copper and copper alloys - Plumbing fittings - Part 3: Compression fittings for use with plastics and multilayer pipes
EN 1254-3:2021

This document specifies product characteristics, assessment methods, compliance criteria of test results and a designation system for fittings with compression ends for use with plastic and multilayer pipes which are defined in the applicable pipe standard. For the purposes of joining plastics pipes, the fitting ends have a size range from 10 mm to 160 mm. The fittings are designed for a service lifetime up to fifty years.
The compression fittings are used up to the operating temperatures and maximum operating pressures as indicated in Annex A.
This European Standard applies to copper alloy fittings. A non-exhaustive list of these copper alloys is given in CEN/TS 13388.
Adaptor fittings for use with plastic and multilayer pipes may combine compression ends with fitting ends defined in the other parts of EN 1254.
Compression fittings for use with plastic and multilayer pipes may also have flanged end connections according to EN 1092-3.
Compression fittings for use with plastic and multilayer pipes may also have a plated or other decorative surface coating.
Fittings can be produced by machining, metal forming, casting, or fabrication.
Products covered by this standard are intended to be used in:
a)   liquid applications:
-   Hot, cold or combined hot and cold water systems according to EN 806;
-   closed heating systems according to EN 12828 and cooling systems;
-   drainage systems;
-   sprinkler systems according to EN 12845.
b)   gas applications (not valid for multilayer pipes):
-   natural gas and liquefied petroleum gas systems with a maximum operating pressure less than or equal to 5 bar according to EN 1775;
-   compressed air systems.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1254-20:2021(Main)
Copper and copper alloys - Plumbing fittings - Part 20: Definitions, thread dimensions, test methods, reference data and supporting information
EN 1254-20:2021

This document contains definitions, thread dimension, reference data (minimum bore), supporting information (assembling instructions) and describes the test methods referenced by other parts of the EN 1254 series.
Thread dimensions comprise: wall thickness at threaded portions of fittings, dimensions of tail pipe ends for swivel fittings, dimensions of gas union connectors, thread dimensions and thread profile.
Test methods comprise: leak tightness under internal hydrostatic pressure, leak tightness under internal pneumatic pressure, resistance of joints to static flexural strength, resistance to pull out of joints, leak tightness of joints under vacuum, the resistance of joints to temperature cycling, resistance of joints with metallic tube to vibration, integrity of fabricated fitting bodies or having an 'as cast' microstructure, resistance to stress corrosion, detection of a carbon film on the surface of copper fittings, determination of mean depth of dezincification, resistance of joints to pressure cycling, disconnection and re-use, determining if the diameter and/or the length of engagement of a capillary end is/are within the specified tolerance, determining the minimum length of engagement of an integral solder or brazing ring socket having a formed groove.

  • Standard
    65 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day