SIST EN 319 412-5 V2.2.1:2018
(Main)Electronic Signatures and Infrastructures (ESI) - Certificate Profiles - Part 5: QCStatements
Electronic Signatures and Infrastructures (ESI) - Certificate Profiles - Part 5: QCStatements
The present document defines specific QCStatement for the qcStatements extension as defined in IETF
RFC 3739 [2], clause 3.2.6, including requirements for their use in EU qualified certificates. Some of these
QCStatements can be used for other forms of certificate.
The QCStatements defined in the present document can be used in combination with any certificate profile, either
defined in ETSI EN 319 412-2 [i.2], ETSI EN 319 412-3 [i.5] and ETSI EN 319 412-4 [i.6], or defined elsewhere.
The QCStatements defined in clause 4.3 may be applied to regulatory environments outside the EU. Other
requirements specified in clause 4 are specific to Regulation (EU) No 910/2014 [i.8] but may be adapted for other
regulatory environments.
Elektronski podpisi in infrastruktura (ESI) - Profili potrdil - 5. del: Izjave QC
Ta dokument določa posebno izjavo QC za razširitev izjav QC, kot je opredeljeno v dokumentu IETF RFC 3739 [2], točka 3.2.6, vključno z zahtevami za njihovo uporabo v kvalificiranih digitalnih potrdilih v EU. Nekatere od teh izjav QC je mogoče uporabljati za druge oblike potrdil.
Izjave QC, določene v tem dokumentu, se lahko uporabljajo v kombinaciji s katerim koli profilom certifikata, opredeljenim v standardih ETSI EN 319 412-2 [i.2], ETSI EN 319 412-3 [i.5] in ETSI EN 319 412-4 [i.6] ali drugje.
Izjave QC, določene v točki 4.3, se lahko uporabljajo za regulativna okolja zunaj EU. Druge zahteve iz točke 4 so specifične za Uredbo (EU) št. 910/2014 [i.8], a se lahko prilagodijo tudi drugim regulativnim okoljem.
General Information
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 319 412-5 V2.2.1:2018
01-januar-2018
Elektronski podpisi in infrastruktura (ESI) - Profili potrdil - 5. del: Izjave QC
Electronic Signatures and Infrastructures (ESI) - Certificate Profiles - Part 5:
QCStatements
Ta slovenski standard je istoveten z: ETSI EN 319 412-5 V2.2.1 (2017-11)
ICS:
03.080.99 Druge storitve Other services
35.040.01 Kodiranje informacij na Information coding in general
splošno
SIST EN 319 412-5 V2.2.1:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 319 412-5 V2.2.1:2018
---------------------- Page: 2 ----------------------
SIST EN 319 412-5 V2.2.1:2018
ETSI EN 319 412-5 V2.2.1 (2017-11)
EUROPEAN STANDARD
Electronic Signatures and Infrastructures (ESI);
Certificate Profiles;
Part 5: QCStatements
---------------------- Page: 3 ----------------------
SIST EN 319 412-5 V2.2.1:2018
2 ETSI EN 319 412-5 V2.2.1 (2017-11)
Reference
REN/ESI-0019412-5v221
Keywords
e-commerce, electronic signature, security,
trust services
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2017.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
GSM® and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 319 412-5 V2.2.1:2018
3 ETSI EN 319 412-5 V2.2.1 (2017-11)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 4
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions and abbreviations . 7
3.1 Definitions . 7
3.2 Abbreviations . 7
4 Qualified certificate statements . 8
4.1 General requirements . 8
4.2 QCStatements claiming compliance with the EU legislation . 8
4.2.1 QCStatement claiming that the certificate is a EU qualified certificate . 8
4.2.2 QCStatement claiming that the private key related to the certified public key resides in a QSCD . 8
4.2.3 QCStatement claiming that the certificate is a EU qualified certificate of a particular type . 9
4.3 Generic QCStatements . 9
4.3.1 Introduction. 9
4.3.2 QCStatement regarding limits on the value of transactions . 9
4.3.3 QCStatement indicating the duration of the retention period of material information . 10
4.3.4 QCStatement regarding location of PKI Disclosure Statements (PDS) . 10
5 Requirements on QCStatements in EU qualified certificates . 11
Annex A (informative): Relationship with the Regulation (EU) No 910/2014 . 12
A.1 EU qualified certificates for electronic signatures . 12
A.2 EU qualified certificates for electronic seals . 13
A.3 EU qualified certificates for website authentication . 14
Annex B (normative): ASN.1 declarations. 15
Annex C (informative): Change History . 17
History . 18
ETSI
---------------------- Page: 5 ----------------------
SIST EN 319 412-5 V2.2.1:2018
4 ETSI EN 319 412-5 V2.2.1 (2017-11)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This European Standard (EN) has been produced by ETSI Technical Committee Electronic Signatures and
Infrastructures (ESI).
The present document is part 5 of multi-part deliverable covering the Certificates Profiles. Full details of the entire
series can be found in part 1 [i.1].
The present document was previously published as ETSI TS 101 862 [i.4].
National transposition dates
Date of adoption of this EN: 21 November 2017
Date of latest announcement of this EN (doa): 28 February 2018
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 August 2018
Date of withdrawal of any conflicting National Standard (dow): 31 August 2018
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 6 ----------------------
SIST EN 319 412-5 V2.2.1:2018
5 ETSI EN 319 412-5 V2.2.1 (2017-11)
Introduction
ITU and ISO issued standards for certification of public keys in Recommendation ITU-T X.509 | ISO/IEC 9594-8 [i.7]
which are used for the security of communications and data for a wide range of electronic applications.
The IETF qualified certificate profile, IETF RFC 3739 [2] defines an extension to X.509 certificates, the
qcStatements extension, which can include statements relevant for qualified certificates. IETF RFC 3739 [2]
defines qualified certificates in a general context as "a certificate whose primary purpose is to identify a person with a
high level of assurance, where the certificate meets some qualification requirements defined by an applicable legal
framework". The use of IETF RFC 3739 [2] qcStatements in the present document goes beyond the scope of the
RFC which is directed at natural persons only.
The qcStatements certificate extension can contain any statement by the certificate issuer that can be useful to the
relying party in determining the applicability of the certificate for an intended usage. Such statement can be a
declaration that the certificate fulfils specific legal requirements for qualified certificates according to a defined legal
framework.
The present document is aiming to meet the general requirements of the international community to provide trust and
confidence in electronic transactions including, amongst others, applicable requirements from Regulation (EU)
No 910/2014 [i.8] Annexes I, III and IV.
ETSI
---------------------- Page: 7 ----------------------
SIST EN 319 412-5 V2.2.1:2018
6 ETSI EN 319 412-5 V2.2.1 (2017-11)
1 Scope
The present document defines specific QCStatement for the qcStatements extension as defined in IETF
RFC 3739 [2], clause 3.2.6, including requirements for their use in EU qualified certificates. Some of these
QCStatements can be used for other forms of certificate.
The QCStatements defined in the present document can be used in combination with any certificate profile, either
defined in ETSI EN 319 412-2 [i.2], ETSI EN 319 412-3 [i.5] and ETSI EN 319 412-4 [i.6], or defined elsewhere.
The QCStatements defined in clause 4.3 may be applied to regulatory environments outside the EU. Other
requirements specified in clause 4 are specific to Regulation (EU) No 910/2014 [i.8] but may be adapted for other
regulatory environments.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ISO 639-1:2002: "Codes for the representation of names of languages -- Part 1: Alpha-2 code".
[2] IETF RFC 3739: "Internet X.509 Public Key Infrastructure: Qualified Certificates Profile".
[3] Recommendation ITU-T X.680-X.699: "Information technology - Abstract Syntax Notation One
(ASN.1)".
[4] ISO 4217: "Codes for the representation of currencies and funds".
[5] IETF RFC 2818: "HTTP Over TLS".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI EN 319 412-1: "Electronic Signatures and Infrastructures (ESI); Certificate Profiles;
Part 1: Overview and common data structures".
[i.2] ETSI EN 319 412-2: "Electronic Signatures and Infrastructures (ESI); Certificate Profiles;
Part 2: Certificate Profile for certificates issued to natural persons".
[i.3] Directive 1999/93/EC of the European Parliament and of the Council of 13 December 1999 on a
Community framework for electronic signatures.
ETSI
---------------------- Page: 8 ----------------------
SIST EN 319 412-5 V2.2.1:2018
7 ETSI EN 319 412-5 V2.2.1 (2017-11)
[i.4] ETSI TS 101 862: "Qualified Certificate profile".
[i.5] ETSI EN 319 412-3: "Electronic Signatures and Infrastructures (ESI); Certificate Profiles;
Part 3: Certificate Profile for certificates issued to legal persons".
[i.6] ETSI EN 319 412-4: "Electronic Signatures and Infrastructures (ESI); Certificate Profiles;
Part 4: Certificate profile for web site certificates".
[i.7] Recommendation ITU-T X.509 | ISO/IEC 9594-8: "Information technology - Open systems
interconnection - The Directory: Public-key and attribute certificate frameworks".
[i.8] Regulation (EU) No 910/2014 of the European Parliament and of the Council on electronic
identification and trust services for electronic transactions in the internal market and repealing
Directive 1999/93/EC.
[i.9] IETF RFC 5280: "Internet X.509 Public Key Infrastructure Certificate and Certificate Revocation
List (CRL) Profile".
[i.10] ETSI EN 319 411-1: "Electronic Signatures and Infrastructures (ESI); Policy and security
requirements for Trust Service Providers issuing certificates; Part 1: General requirements".
[i.11] CA/Browser Forum: "Baseline Requirements for the Issuance and Management of Publicly-
Trusted Certificates".
[i.12] CA/Browser Forum: "Guidelines for The Issuance and Management of Extended Validation
Certificates".
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in ETSI EN 319 412-1 [i.1] and the following
apply:
EU qualified certificate: qualified certificate that is stated to be in accordance with Annex I, III or IV of the Regulation
(EU) No 910/2014 [i.8] or Annex I of the Directive 1999/93/EC [i.3] whichever is in force at the time of issuance
QCStatement: statement for inclusion in a qcStatements certificates extension as specified in IETF RFC 3739 [2]
qualified electronic signature/seal creation device: As specified in Regulation (EU) No 910/2014 [i.8].
secure signature creation device: As specified in Directive 1999/93 [i.3].
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
ASN.1 Abstract Syntax Notation One
CA Certification Authority
CRL Certificate Revocation List
EC European Commission
EU European Union
IETF Internet Engineering Task Force
ISO International Organization for Standardization
PDS PKI Disclosure Statements
PKI Public Key Infrastructure
QC Qualified Certificate
QSCD Qualified electronic Signature/Seal Creation Device
RFC Request For Comments
URL Uniform Resource Locator
ETSI
---------------------- Page: 9 ----------------------
SIST EN 319 412-5 V2.2.1:2018
8 ETSI EN 319 412-5 V2.2.1 (2017-11)
4 Qualified certificate statements
4.1 General requirements
The qcStatements extension shall be as specified in clause 3.2.6 of IETF RFC 3739 [2]. The qcStatements
extension shall not be marked as critical.
The following clauses define a number of individual QCStatements to be included in the qcStatements
extension.
The syntax of the defined statements shall comply with ASN.1 [3]. The complete ASN.1 module for all defined
statements shall be as provided in Annex B; it takes precedence over the ASN.1 definitions provided in the body of the
present document, in case of discrepancy.
NOTE: This extension is not processed as part of IETF RFC 5280 [i.9] path validation and there are no security
implications with accepting a certificate in a system that cannot parse this extension.
4.2 QCStatements claiming compliance with the EU
legislation
4.2.1 QCStatement claiming that the certificate is a EU qualified
certificate
This Qcstatement claims that the certificate is an EU qualified certificate that is issued according to Directive
1999/93/EC [i.3] or the Annex I, III or IV of the Regulation (EU) No 910/2014 [i.8] whichever is in force at the time of
issuance.
Syntax:
esi4-qcStatement-1 QC-STATEMENT ::= { IDENTIFIED BY id-etsi-qcs-QcCompliance }
id-etsi-qcs-QcCompliance OBJECT IDENTIFIER ::= { id-etsi-qcs 1 }
The precise meaning of this statement is enhanced by the QC type statement defined in clause 4.2.3 according to the
table 1.
Table 1: esi4-qcStatement-1 meaning
QC type statement Meaning of this statement (esi4-qcStatement-1)
(clause 4.2.3)
Absent The certificate is issued according to Directive 1999/93/EC [i.3] or Annex I of the Regulation
(EU) No 910/2014 [i.8] (for electronic signatures).
Present The certificate is issued according to Annex I, III or IV of Regulation (EU) No 910/2014 [i.8]
as of the types declared by the QC type statement in accordance with clause 4.2.3.
A certificate that includes this statement shall comply with all requirements defined in clause 5.
4.2.2 QCStatement claiming that the private key related to the certified
public key resides in a QSCD
This Qcstatement declares that the private key related to the certified public key resides in a Qualified
Signature/Seal Creation Device (QSCD) according to the Regulation (EU) No 910/2014 [i.8] or a secure signature
creation device as defined in the Directive 1999/93/EC [i.3].
Syntax:
esi4-qcStatement-4 QC-STATEMENT ::= { IDENTIFIED BY id-etsi-qcs-QcSSCD }
ETSI
---------------------- Page: 10 ----------------------
SIST EN 319 412-5 V2.2.1:2018
9 ETSI EN 319 412-5 V2.2.1 (2017-11)
id-etsi-qcs-QcSSCD OBJECT IDENTIFIER ::= { id-etsi-qcs 4 }
4.2.3 QCStatement claiming that the certificate is a EU qualified
certificate of a particular type
This QCStatement declares that a certificate is issued as one and only one of the purposes of electronic signature,
electronic seal or web site authentication.
This QCStatements states that an EU qualified certificate is issued as one specific types according to Annexes I, III or
IV of the Regulation (EU) No 910/2014 [i.8] when used in combination with the qcStatement as defined in clause 4.2.1.
When used on its own it indicates that it is used for the purposes of electronic signatures, seals or web sites for "non-
qualified certificates" within the context of Regulation (EU) No 910/2014 [i.8].
NOTE: This statement, without the one defined in clause 4.2.1, can be potentially used in other regulatory
environments which use electronic signature, electronic seal or web site with the same meaning.
Syntax:
esi4-qcS
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Elektronski podpisi in infrastruktura (ESI) - Profili potrdil - 5. del: Izjave QCElectronic Signatures and Infrastructures (ESI) - Certificate Profiles - Part 5: QCStatements35.030Informacijska varnostIT Security03.080.99Druge storitveOther servicesICS:Ta slovenski standard je istoveten z:ETSI EN 319 412-5 V2.2.1 (2017-11)SIST EN 319 412-5 V2.2.1:2018en01-januar-2018SIST EN 319 412-5 V2.2.1:2018SLOVENSKI
STANDARD
SIST EN 319 412-5 V2.2.1:2018
ETSI EN 319 412-5 V2.2.1 (2017-11) Electronic Signatures and Infrastructures (ESI); Certificate Profiles; Part 5: QCStatements
EUROPEAN STANDARD SIST EN 319 412-5 V2.2.1:2018
ETSI ETSI EN 319 412-5 V2.2.1 (2017-11) 2
Reference REN/ESI-0019412-5v221 Keywords e-commerce, electronic signature, security, trust services ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2017. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are trademarks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSM® and the GSM logo are trademarks registered and owned by the GSM Association. SIST EN 319 412-5 V2.2.1:2018
ETSI ETSI EN 319 412-5 V2.2.1 (2017-11) 3 Contents Intellectual Property Rights . 4 Foreword . 4 Modal verbs terminology . 4 Introduction . 5 1 Scope . 6 2 References . 6 2.1 Normative references . 6 2.2 Informative references . 6 3 Definitions and abbreviations . 7 3.1 Definitions . 7 3.2 Abbreviations . 7 4 Qualified certificate statements . 8 4.1 General requirements . 8 4.2 QCStatements claiming compliance with the EU legislation . 8 4.2.1 QCStatement claiming that the certificate is a EU qualified certificate . 8 4.2.2 QCStatement claiming that the private key related to the certified public key resides in a QSCD . 8 4.2.3 QCStatement claiming that the certificate is a EU qualified certificate of a particular type . 9 4.3 Generic QCStatements . 9 4.3.1 Introduction. 9 4.3.2 QCStatement regarding limits on the value of transactions . 9 4.3.3 QCStatement indicating the duration of the retention period of material information . 10 4.3.4 QCStatement regarding location of PKI Disclosure Statements (PDS) . 10 5 Requirements on QCStatements in EU qualified certificates . 11 Annex A (informative): Relationship with the Regulation (EU) No 910/2014 . 12 A.1 EU qualified certificates for electronic signatures . 12 A.2 EU qualified certificates for electronic seals . 13 A.3 EU qualified certificates for website authentication . 14 Annex B (normative): ASN.1 declarations. 15 Annex C (informative): Change History . 17 History . 18
SIST EN 319 412-5 V2.2.1:2018
ETSI ETSI EN 319 412-5 V2.2.1 (2017-11) 4 Intellectual Property Rights Essential patents IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https://ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Trademarks The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks. Foreword This European Standard (EN) has been produced by ETSI Technical Committee Electronic Signatures and Infrastructures (ESI). The present document is part 5 of multi-part deliverable covering the Certificates Profiles. Full details of the entire series can be found in part 1 [i.1]. The present document was previously published as ETSI TS 101 862 [i.4].
National transposition dates Date of adoption of this EN: 21 November 2017 Date of latest announcement of this EN (doa): 28 February 2018 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
31 August 2018 Date of withdrawal of any conflicting National Standard (dow): 31 August 2018
Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation. SIST EN 319 412-5 V2.2.1:2018
ETSI ETSI EN 319 412-5 V2.2.1 (2017-11) 5 Introduction ITU and ISO issued standards for certification of public keys in Recommendation ITU-T X.509 | ISO/IEC 9594-8 [i.7] which are used for the security of communications and data for a wide range of electronic applications. The IETF qualified certificate profile, IETF RFC 3739 [2] defines an extension to X.509 certificates, the qcStatements extension, which can include statements relevant for qualified certificates. IETF RFC 3739 [2] defines qualified certificates in a general context as "a certificate whose primary purpose is to identify a person with a high level of assurance, where the certificate meets some qualification requirements defined by an applicable legal framework". The use of IETF RFC 3739 [2] qcStatements in the present document goes beyond the scope of the RFC which is directed at natural persons only. The qcStatements certificate extension can contain any statement by the certificate issuer that can be useful to the relying party in determining the applicability of the certificate for an intended usage. Such statement can be a declaration that the certificate fulfils specific legal requirements for qualified certificates according to a defined legal framework. The present document is aiming to meet the general requirements of the international community to provide trust and confidence in electronic transactions including, amongst others, applicable requirements from Regulation (EU) No 910/2014 [i.8] Annexes I, III and IV. SIST EN 319 412-5 V2.2.1:2018
ETSI ETSI EN 319 412-5 V2.2.1 (2017-11) 6 1 Scope The present document defines specific QCStatement for the qcStatements extension as defined in IETF RFC 3739 [2], clause 3.2.6, including requirements for their use in EU qualified certificates. Some of these QCStatements can be used for other forms of certificate. The QCStatements defined in the present document can be used in combination with any certificate profile, either defined in ETSI EN 319 412-2 [i.2], ETSI EN 319 412-3 [i.5] and ETSI EN 319 412-4 [i.6], or defined elsewhere. The QCStatements defined in clause 4.3 may be applied to regulatory environments outside the EU. Other requirements specified in clause 4 are specific to Regulation (EU) No 910/2014 [i.8] but may be adapted for other regulatory environments. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at https://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. [1] ISO 639-1:2002: "Codes for the representation of names of languages -- Part 1: Alpha-2 code". [2] IETF RFC 3739: "Internet X.509 Public Key Infrastructure: Qualified Certificates Profile". [3] Recommendation ITU-T X.680-X.699: "Information technology - Abstract Syntax Notation One (ASN.1)". [4] ISO 4217: "Codes for the representation of currencies and funds". [5] IETF RFC 2818: "HTTP Over TLS". 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] ETSI EN 319 412-1: "Electronic Signatures and Infrastructures (ESI); Certificate Profiles; Part 1: Overview and common data structures". [i.2] ETSI EN 319 412-2: "Electronic Signatures and Infrastructures (ESI); Certificate Profiles; Part 2: Certificate Profile for certificates issued to natural persons". [i.3] Directive 1999/93/EC of the European Parliament and of the Council of 13 December 1999 on a Community framework for electronic signatures. SIST EN 319 412-5 V2.2.1:2018
ETSI ETSI EN 319 412-5 V2.2.1 (2017-11) 7 [i.4] ETSI TS 101 862: "Qualified Certificate profile". [i.5] ETSI EN 319 412-3: "Electronic Signatures and Infrastructures (ESI); Certificate Profiles; Part 3: Certificate Profile for certificates issued to legal persons". [i.6] ETSI EN 319 412-4: "Electronic Signatures and Infrastructures (ESI); Certificate Profiles; Part 4: Certificate profile for web site certificates". [i.7] Recommendation ITU-T X.509 | ISO/IEC 9594-8: "Information technology - Open systems interconnection - The Directory: Public-key and attribute certificate frameworks". [i.8] Regulation (EU) No 910/2014 of the European Parliament and of the Council on electronic identification and trust services for electronic transactions in the internal market and repealing Directive 1999/93/EC. [i.9] IETF RFC 5280: "Internet X.509 Public Key Infrastructure Certificate and Certificate Revocation List (CRL) Profile". [i.10] ETSI EN 319 411-1: "Electronic Signatures and Infrastructures (ESI); Policy and security requirements for Trust Service Providers issuing certificates; Part 1: General requirements". [i.11] CA/Browser Forum: "Baseline Requirements for the Issuance and Management of Publicly-Trusted Certificates". [i.12] CA/Browser Forum: "Guidelines for The Issuance and Management of Extended Validation Certificates". 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ETSI EN 319 412-1 [i.1] and the following apply: EU qualified certificate: qualified certificate that is stated to be in accordance with Annex I, III or IV of the Regulation (EU) No 910/2014 [i.8] or Annex I of the Directive 1999/93/EC [i.3] whichever is in force at the time of issuance QCStatement: statement for inclusion in a qcStatements certificates extension as specified in IETF RFC 3739 [2] qualified electronic signature/seal creation device: As specified in Regulation (EU) No 910/2014 [i.8]. secure signature creation device: As specified in Directive 1999/93 [i.3]. 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: ASN.1 Abstract Syntax Notation One CA Certification Authority CRL Certificate Revocation List EC European Commission EU European Union IETF Internet Engineering Task Force ISO International Organization for Standardization PDS PKI Disclosure Statements PKI Public Key Infrastructure QC Qualified Certificate QSCD Qualified electronic Signature/Seal Creation Device RFC Request For Comments URL Uniform Resource Locator SIST EN 319 412-5 V2.2.1:2018
ETSI ETSI EN 319 412-5 V2.2.1 (2017-11) 8 4 Qualified certificate statements 4.1 General requirements The qcStatements extension shall be as specified in clause 3.2.6 of IETF RFC 3739 [2]. The qcStatements extension shall not be marked as critical. The following clauses define a number of individual QCStatements to be included in the qcStatements extension. The syntax of the defined statements shall comply with ASN.1 [3]. The complete ASN.1 module for all defined statements shall be as provided in Annex B; it takes precedence over the ASN.1 definitions provided in the body of the present document, in case of discrepancy. NOTE: This extension is not processed as part of IETF RFC 5280 [i.9] path validation and there are no security implications with accepting a certificate in a system that cannot parse this extension. 4.2 QCStatements claiming compliance with the EU legislation 4.2.1 QCStatement claiming that the certificate is a EU qualified certificate This Qcstatement claims that the certificate is an EU qualified certificate that is issued according to Directive 1999/93/EC [i.3] or the Annex I, III or IV of the Regulation (EU) No 910/2014 [i.8] whichever is in force at the time of issuance. Syntax:
esi4-qcStatement-1 QC-STATEMENT ::= { IDENTIFIED BY id-etsi-qcs-QcCompliance }
id-etsi-qcs-QcCompliance
OBJECT IDENTIFIER ::= { id-etsi-qcs 1 }
The precise meaning of this statement is enhanced by the QC type statement defined in clause 4.2.3 according to the table 1. Table 1: esi4-qcStatement-1 meaning QC type statement (clause 4.2.3) Meaning of this statement (esi4-qcStatement-1) Absent The certificate is issued according to Directive 1999/93/EC [i.3] or Annex I of the Regulation (EU) No 910/2014 [i.8] (for electronic signatures). Present The certificate is issued according to Annex I, III or IV of Regulation (EU) No 910/2014 [i.8] as of the types declared by the QC type statement in accordance with clause 4.2.3.
A certificate that includes this statement shall comply with all requirements defined in clause 5. 4.2.2 QCStatement claiming that the private key related to the certified public key resides in a QSCD This Qcstatement declares that the private key related to the certified public key resides in a Qualified Signature/Seal Creation Device (QSCD) according to the Regulation (EU) No 910/2014 [i.8] or a secure signature creation device as defined in the Directive 1999/93/EC [i.3]. Syntax:
esi4-qcStatement-4 QC-STATEMENT ::= { IDENTIFIED BY id-etsi-qcs-QcSSCD
}
SIST EN 319 412-5 V2.2.1:2018
ETSI ETSI EN 319 412-5 V2.2.1 (2017-11) 9
id-etsi-qcs-QcSSCD
OBJECT IDENTIFIER ::= { id-etsi-qcs 4 }
4.2.3 QCStatement claiming that the certificate is a EU qualified certificate of a particular type This QCStatement declares that a certificate is issued as one and only one of the purposes
of electronic signature, electronic seal or web site authentication.
This QCStatements states that an EU qualified certificate is issued as one specific types according to Annexes I, III or IV of the Regulation (EU) No 910/2014 [i.8] when used in combination with the qcStatement as defined in clause 4.2.1. When used on its own it indicates that it is used for the purposes of electronic signatures, seals or web sites for "non-qualified certificates" within the context of
...
ETSI EN 319 412-5 V2.2.1 (2017-11)
EUROPEAN STANDARD
Electronic Signatures and Infrastructures (ESI);
Certificate Profiles;
Part 5: QCStatements
---------------------- Page: 1 ----------------------
2 ETSI EN 319 412-5 V2.2.1 (2017-11)
Reference
REN/ESI-0019412-5v221
Keywords
e-commerce, electronic signature, security,
trust services
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2017.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
GSM® and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 319 412-5 V2.2.1 (2017-11)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 4
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions and abbreviations . 7
3.1 Definitions . 7
3.2 Abbreviations . 7
4 Qualified certificate statements . 8
4.1 General requirements . 8
4.2 QCStatements claiming compliance with the EU legislation . 8
4.2.1 QCStatement claiming that the certificate is a EU qualified certificate . 8
4.2.2 QCStatement claiming that the private key related to the certified public key resides in a QSCD . 8
4.2.3 QCStatement claiming that the certificate is a EU qualified certificate of a particular type . 9
4.3 Generic QCStatements . 9
4.3.1 Introduction. 9
4.3.2 QCStatement regarding limits on the value of transactions . 9
4.3.3 QCStatement indicating the duration of the retention period of material information . 10
4.3.4 QCStatement regarding location of PKI Disclosure Statements (PDS) . 10
5 Requirements on QCStatements in EU qualified certificates . 11
Annex A (informative): Relationship with the Regulation (EU) No 910/2014 . 12
A.1 EU qualified certificates for electronic signatures . 12
A.2 EU qualified certificates for electronic seals . 13
A.3 EU qualified certificates for website authentication . 14
Annex B (normative): ASN.1 declarations. 15
Annex C (informative): Change History . 17
History . 18
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 319 412-5 V2.2.1 (2017-11)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This European Standard (EN) has been produced by ETSI Technical Committee Electronic Signatures and
Infrastructures (ESI).
The present document is part 5 of multi-part deliverable covering the Certificates Profiles. Full details of the entire
series can be found in part 1 [i.1].
The present document was previously published as ETSI TS 101 862 [i.4].
National transposition dates
Date of adoption of this EN: 21 November 2017
Date of latest announcement of this EN (doa): 28 February 2018
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 August 2018
Date of withdrawal of any conflicting National Standard (dow): 31 August 2018
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 319 412-5 V2.2.1 (2017-11)
Introduction
ITU and ISO issued standards for certification of public keys in Recommendation ITU-T X.509 | ISO/IEC 9594-8 [i.7]
which are used for the security of communications and data for a wide range of electronic applications.
The IETF qualified certificate profile, IETF RFC 3739 [2] defines an extension to X.509 certificates, the
qcStatements extension, which can include statements relevant for qualified certificates. IETF RFC 3739 [2]
defines qualified certificates in a general context as "a certificate whose primary purpose is to identify a person with a
high level of assurance, where the certificate meets some qualification requirements defined by an applicable legal
framework". The use of IETF RFC 3739 [2] qcStatements in the present document goes beyond the scope of the
RFC which is directed at natural persons only.
The qcStatements certificate extension can contain any statement by the certificate issuer that can be useful to the
relying party in determining the applicability of the certificate for an intended usage. Such statement can be a
declaration that the certificate fulfils specific legal requirements for qualified certificates according to a defined legal
framework.
The present document is aiming to meet the general requirements of the international community to provide trust and
confidence in electronic transactions including, amongst others, applicable requirements from Regulation (EU)
No 910/2014 [i.8] Annexes I, III and IV.
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 319 412-5 V2.2.1 (2017-11)
1 Scope
The present document defines specific QCStatement for the qcStatements extension as defined in IETF
RFC 3739 [2], clause 3.2.6, including requirements for their use in EU qualified certificates. Some of these
QCStatements can be used for other forms of certificate.
The QCStatements defined in the present document can be used in combination with any certificate profile, either
defined in ETSI EN 319 412-2 [i.2], ETSI EN 319 412-3 [i.5] and ETSI EN 319 412-4 [i.6], or defined elsewhere.
The QCStatements defined in clause 4.3 may be applied to regulatory environments outside the EU. Other
requirements specified in clause 4 are specific to Regulation (EU) No 910/2014 [i.8] but may be adapted for other
regulatory environments.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ISO 639-1:2002: "Codes for the representation of names of languages -- Part 1: Alpha-2 code".
[2] IETF RFC 3739: "Internet X.509 Public Key Infrastructure: Qualified Certificates Profile".
[3] Recommendation ITU-T X.680-X.699: "Information technology - Abstract Syntax Notation One
(ASN.1)".
[4] ISO 4217: "Codes for the representation of currencies and funds".
[5] IETF RFC 2818: "HTTP Over TLS".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI EN 319 412-1: "Electronic Signatures and Infrastructures (ESI); Certificate Profiles;
Part 1: Overview and common data structures".
[i.2] ETSI EN 319 412-2: "Electronic Signatures and Infrastructures (ESI); Certificate Profiles;
Part 2: Certificate Profile for certificates issued to natural persons".
[i.3] Directive 1999/93/EC of the European Parliament and of the Council of 13 December 1999 on a
Community framework for electronic signatures.
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 319 412-5 V2.2.1 (2017-11)
[i.4] ETSI TS 101 862: "Qualified Certificate profile".
[i.5] ETSI EN 319 412-3: "Electronic Signatures and Infrastructures (ESI); Certificate Profiles;
Part 3: Certificate Profile for certificates issued to legal persons".
[i.6] ETSI EN 319 412-4: "Electronic Signatures and Infrastructures (ESI); Certificate Profiles;
Part 4: Certificate profile for web site certificates".
[i.7] Recommendation ITU-T X.509 | ISO/IEC 9594-8: "Information technology - Open systems
interconnection - The Directory: Public-key and attribute certificate frameworks".
[i.8] Regulation (EU) No 910/2014 of the European Parliament and of the Council on electronic
identification and trust services for electronic transactions in the internal market and repealing
Directive 1999/93/EC.
[i.9] IETF RFC 5280: "Internet X.509 Public Key Infrastructure Certificate and Certificate Revocation
List (CRL) Profile".
[i.10] ETSI EN 319 411-1: "Electronic Signatures and Infrastructures (ESI); Policy and security
requirements for Trust Service Providers issuing certificates; Part 1: General requirements".
[i.11] CA/Browser Forum: "Baseline Requirements for the Issuance and Management of Publicly-
Trusted Certificates".
[i.12] CA/Browser Forum: "Guidelines for The Issuance and Management of Extended Validation
Certificates".
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in ETSI EN 319 412-1 [i.1] and the following
apply:
EU qualified certificate: qualified certificate that is stated to be in accordance with Annex I, III or IV of the Regulation
(EU) No 910/2014 [i.8] or Annex I of the Directive 1999/93/EC [i.3] whichever is in force at the time of issuance
QCStatement: statement for inclusion in a qcStatements certificates extension as specified in IETF RFC 3739 [2]
qualified electronic signature/seal creation device: As specified in Regulation (EU) No 910/2014 [i.8].
secure signature creation device: As specified in Directive 1999/93 [i.3].
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
ASN.1 Abstract Syntax Notation One
CA Certification Authority
CRL Certificate Revocation List
EC European Commission
EU European Union
IETF Internet Engineering Task Force
ISO International Organization for Standardization
PDS PKI Disclosure Statements
PKI Public Key Infrastructure
QC Qualified Certificate
QSCD Qualified electronic Signature/Seal Creation Device
RFC Request For Comments
URL Uniform Resource Locator
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 319 412-5 V2.2.1 (2017-11)
4 Qualified certificate statements
4.1 General requirements
The qcStatements extension shall be as specified in clause 3.2.6 of IETF RFC 3739 [2]. The qcStatements
extension shall not be marked as critical.
The following clauses define a number of individual QCStatements to be included in the qcStatements
extension.
The syntax of the defined statements shall comply with ASN.1 [3]. The complete ASN.1 module for all defined
statements shall be as provided in Annex B; it takes precedence over the ASN.1 definitions provided in the body of the
present document, in case of discrepancy.
NOTE: This extension is not processed as part of IETF RFC 5280 [i.9] path validation and there are no security
implications with accepting a certificate in a system that cannot parse this extension.
4.2 QCStatements claiming compliance with the EU
legislation
4.2.1 QCStatement claiming that the certificate is a EU qualified
certificate
This Qcstatement claims that the certificate is an EU qualified certificate that is issued according to Directive
1999/93/EC [i.3] or the Annex I, III or IV of the Regulation (EU) No 910/2014 [i.8] whichever is in force at the time of
issuance.
Syntax:
esi4-qcStatement-1 QC-STATEMENT ::= { IDENTIFIED BY id-etsi-qcs-QcCompliance }
id-etsi-qcs-QcCompliance OBJECT IDENTIFIER ::= { id-etsi-qcs 1 }
The precise meaning of this statement is enhanced by the QC type statement defined in clause 4.2.3 according to the
table 1.
Table 1: esi4-qcStatement-1 meaning
QC type statement Meaning of this statement (esi4-qcStatement-1)
(clause 4.2.3)
Absent The certificate is issued according to Directive 1999/93/EC [i.3] or Annex I of the Regulation
(EU) No 910/2014 [i.8] (for electronic signatures).
Present The certificate is issued according to Annex I, III or IV of Regulation (EU) No 910/2014 [i.8]
as of the types declared by the QC type statement in accordance with clause 4.2.3.
A certificate that includes this statement shall comply with all requirements defined in clause 5.
4.2.2 QCStatement claiming that the private key related to the certified
public key resides in a QSCD
This Qcstatement declares that the private key related to the certified public key resides in a Qualified
Signature/Seal Creation Device (QSCD) according to the Regulation (EU) No 910/2014 [i.8] or a secure signature
creation device as defined in the Directive 1999/93/EC [i.3].
Syntax:
esi4-qcStatement-4 QC-STATEMENT ::= { IDENTIFIED BY id-etsi-qcs-QcSSCD }
ETSI
---------------------- Page: 8 ----------------------
9 ETSI EN 319 412-5 V2.2.1 (2017-11)
id-etsi-qcs-QcSSCD OBJECT IDENTIFIER ::= { id-etsi-qcs 4 }
4.2.3 QCStatement claiming that the certificate is a EU qualified
certificate of a particular type
This QCStatement declares that a certificate is issued as one and only one of the purposes of electronic signature,
electronic seal or web site authentication.
This QCStatements states that an EU qualified certificate is issued as one specific types according to Annexes I, III or
IV of the Regulation (EU) No 910/2014 [i.8] when used in combination with the qcStatement as defined in clause 4.2.1.
When used on its own it indicates that it is used for the purposes of electronic signatures, seals or web sites for "non-
qualified certificates" within the context of Regulation (EU) No 910/2014 [i.8].
NOTE: This statement, without the one defined in clause 4.2.1, can be potentially used in other regulatory
environments which use electronic signature, electronic seal or web site with the same meaning.
Syntax:
esi4-qcStatement-6 QC-STATEMENT ::= { SYNTAX QcType IDENTIFIED
BY id-etsi-qcs-QcType }
Id-etsi-qcs-QcType OBJECT IDENTIFIER ::= { id-etsi-qcs 6 }
QcType::= SEQUENCE OF OBJECT IDENTIFIER (id-etsi-qct-esign | id-etsi-qct-eseal |
id-etsi-qct-web, .)
-- QC type identifiers
id-etsi-qct-esign OBJECT IDENTIFIER ::= { id-etsi-
...
Draft ETSI EN 319 412-5 V2.2.0 (2017-08)
EUROPEAN STANDARD
Electronic Signatures and Infrastructures (ESI);
Certificate Profiles;
Part 5: QCStatements
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 319 412-5 V2.2.0 (2017-08)
Reference
REN/ESI-0019412-5v221
Keywords
e-commerce, electronic signature, security, trust
services
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2017.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
GSM® and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 319 412-5 V2.2.0 (2017-08)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 4
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions and abbreviations . 7
3.1 Definitions . 7
3.2 Abbreviations . 7
4 Qualified certificate statements . 8
4.1 General requirements . 8
4.2 QCStatements claiming compliance with the EU legislation . 8
4.2.1 QCStatement claiming that the certificate is a EU qualified certificate . 8
4.2.2 QCStatement claiming that the private key related to the certified public key resides in a QSCD . 8
4.2.3 QCStatement claiming that the certificate is a EU qualified certificate of a particular type . 9
4.3 Generic QCStatements . 9
4.3.1 Introduction. 9
4.3.2 QCStatement regarding limits on the value of transactions . 9
4.3.3 QCStatement indicating the duration of the retention period of material information . 10
4.3.4 QCStatement regarding location of PKI Disclosure Statements (PDS) . 10
5 Requirements on QCStatements in EU qualified certificates . 11
Annex A (informative): Relationship with the Regulation (EU) No 910/2014 . 12
A.1 EU qualified certificates for electronic signatures . 12
A.2 EU qualified certificates for electronic seals . 13
A.3 EU qualified certificates for website authentication . 14
Annex B (normative): ASN.1 declarations. 15
Annex C (informative): Change History . 17
History . 18
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 319 412-5 V2.2.0 (2017-08)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft European Standard (EN) has been produced by ETSI Technical Committee Electronic Signatures and
Infrastructures (ESI), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI standards EN
Approval Procedure.
The present document is part 5 of multi-part deliverable covering the Certificates Profiles. Full details of the entire
series can be found in part 1 [i.1].
The present document was previously published as ETSI TS 101 862 [i.4].
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 6 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 319 412-5 V2.2.0 (2017-08)
Introduction
ITU and ISO issued standards for certification of public keys in Recommendation ITU-T X.509 | ISO/IEC 9594-8 [i.7]
which are used for the security of communications and data for a wide range of electronic applications.
The IETF qualified certificate profile, IETF RFC 3739 [2] defines an extension to X.509 certificates, the
qcStatements extension, which can include statements relevant for qualified certificates. IETF RFC 3739 [2]
defines qualified certificates in a general context as "a certificate whose primary purpose is to identify a person with a
high level of assurance, where the certificate meets some qualification requirements defined by an applicable legal
framework". The use of IETF RFC 3739 [2] qcStatements in the present document goes beyond the scope of the
RFC which is directed at natural persons only.
The qcStatements certificate extension can contain any statement by the certificate issuer that can be useful to the
relying party in determining the applicability of the certificate for an intended usage. Such statement can be a
declaration that the certificate fulfils specific legal requirements for qualified certificates according to a defined legal
framework.
The present document is aiming to meet the general requirements of the international community to provide trust and
confidence in electronic transactions including, amongst others, applicable requirements from Regulation (EU)
No 910/2014 [i.8] Annexes I, III and IV.
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 319 412-5 V2.2.0 (2017-08)
1 Scope
The present document defines specific QCStatement for the qcStatements extension as defined in IETF
RFC 3739 [2], clause 3.2.6, including requirements for their use in EU qualified certificates. Some of these
QCStatements can be used for other forms of certificate.
The QCStatements defined in the present document can be used in combination with any certificate profile, either
defined in ETSI EN 319 412-2 [i.2], ETSI EN 319 412-3 [i.5] and ETSI EN 319 412-4 [i.6], or defined elsewhere.
The QCStatements defined in clause 4.3 may be applied to regulatory environments outside the EU. Other
requirements specified in clause 4 are specific to Regulation (EU) No 910/2014 [i.8] but may be adapted for other
regulatory environments.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ISO 639-1:2002: "Codes for the representation of names of languages -- Part 1: Alpha-2 code".
[2] IETF RFC 3739: "Internet X.509 Public Key Infrastructure: Qualified Certificates Profile".
[3] Recommendation ITU-T X.680-X.699: "Information technology - Abstract Syntax Notation One
(ASN.1)".
[4] ISO 4217: "Codes for the representation of currencies and funds".
[5] IETF RFC 2818: "HTTP Over TLS".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI EN 319 412-1: "Electronic Signatures and Infrastructures (ESI); Certificate Profiles;
Part 1: Overview and common data structures".
[i.2] ETSI EN 319 412-2: "Electronic Signatures and Infrastructures (ESI); Certificate Profiles;
Part 2: Certificate Profile for certificates issued to natural persons".
[i.3] Directive 1999/93/EC of the European Parliament and of the Council of 13 December 1999 on a
Community framework for electronic signatures.
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 319 412-5 V2.2.0 (2017-08)
[i.4] ETSI TS 101 862: "Qualified Certificate profile".
[i.5] ETSI EN 319 412-3: "Electronic Signatures and Infrastructures (ESI); Certificate Profiles;
Part 3: Certificate Profile for certificates issued to legal persons".
[i.6] ETSI EN 319 412-4: "Electronic Signatures and Infrastructures (ESI); Certificate Profiles;
Part 4: Certificate profile for web site certificates".
[i.7] Recommendation ITU-T X.509 | ISO/IEC 9594-8: "Information technology - Open systems
interconnection - The Directory: Public-key and attribute certificate frameworks".
[i.8] Regulation (EU) No 910/2014 of the European Parliament and of the Council on electronic
identification and trust services for electronic transactions in the internal market and repealing
Directive 1999/93/EC.
[i.9] IETF RFC 5280: "Internet X.509 Public Key Infrastructure Certificate and Certificate Revocation
List (CRL) Profile".
[i.10] ETSI EN 319 411-1: "Electronic Signatures and Infrastructures (ESI); Policy and security
requirements for Trust Service Providers issuing certificates; Part 1: General requirements".
[i.11] CA/Browser Forum: "Baseline Requirements for the Issuance and Management of Publicly-
Trusted Certificates".
[i.12] CA/Browser Forum: "Guidelines for The Issuance and Management of Extended Validation
Certificates".
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in ETSI EN 319 412-1 [i.1] and the following
apply:
EU qualified certificate: qualified certificate that is stated to be in accordance with Annex I, III or IV of the Regulation
(EU) No 910/2014 [i.8] or Annex I of the Directive 1999/93/EC [i.3] whichever is in force at the time of issuance
QCStatement: statement for inclusion in a qcStatements certificates extension as specified in IETF RFC 3739 [2]
qualified electronic signature/seal creation device: As specified in Regulation (EU) No 910/2014 [i.8].
secure signature creation device: As specified in Directive 1999/93 [i.3].
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
ASN.1 Abstract Syntax Notation One
CA Certification Authority
CRL Certificate Revocation List
EC European Commission
EU European Union
IETF Internet Engineering Task Force
ISO International Organization for Standardization
PDS PKI Disclosure Statements
PKI Public Key Infrastructure
QC Qualified Certificate
QSCD Qualified electronic Signature/Seal Creation Device
RFC Request For Comments
URL Uniform Resource Locator
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 319 412-5 V2.2.0 (2017-08)
4 Qualified certificate statements
4.1 General requirements
The qcStatements extension shall be as specified in clause 3.2.6 of IETF RFC 3739 [2]. The qcStatements
extension shall not be marked as critical.
The following clauses define a number of individual QCStatements to be included in the qcStatements
extension.
The syntax of the defined statements shall comply with ASN.1 [3]. The complete ASN.1 module for all defined
statements shall be as provided in Annex B; it takes precedence over the ASN.1 definitions provided in the body of the
present document, in case of discrepancy.
NOTE: This extension is not processed as part of IETF RFC 5280 [i.9] path validation and there are no security
implications with accepting a certificate in a system that cannot parse this extension.
4.2 QCStatements claiming compliance with the EU
legislation
4.2.1 QCStatement claiming that the certificate is a EU qualified
certificate
This Qcstatement claims that the certificate is an EU qualified certificate that is issued according to Directive
1999/93/EC [i.3] or the Annex I, III or IV of the Regulation (EU) No 910/2014 [i.8] whichever is in force at the time of
issuance.
Syntax:
esi4-qcStatement-1 QC-STATEMENT ::= { IDENTIFIED BY id-etsi-qcs-QcCompliance }
id-etsi-qcs-QcCompliance OBJECT IDENTIFIER ::= { id-etsi-qcs 1 }
The precise meaning of this statement is enhanced by the QC type statement defined in clause 4.2.3 according to the
table 1.
Table 1: esi4-qcStatement-1 meaning
QC type statement Meaning of this statement (esi4-qcStatement-1)
(clause 4.2.3)
Absent The certificate is issued according to Directive 1999/93/EC [i.3] or Annex I of the Regulation
(EU) No 910/2014 [i.8] (for electronic signatures).
Present The certificate is issued according to Annex I, III or IV of Regulation (EU) No 910/2014 [i.8]
as of the types declared by the QC type statement in accordance with clause 4.2.3.
A certificate that includes this statement shall comply with all requirements defined in clause 5.
4.2.2 QCStatement claiming that the private key related to the certified
public key resides in a QSCD
This Qcstatement declares that the private key related to the certified public key resides in a Qualified
Signature/Seal Creation Device (QSCD) according to the Regulation (EU) No 910/2014 [i.8] or a secure signature
creation device as defined in the Directive 1999/93/EC [i.3].
Syntax:
esi4-qcStatement-4 QC-STATEMENT ::= { IDENTIFIED BY id-etsi-qcs-QcSSCD }
ETSI
---------------------- Page: 8 ----------------------
9 Draft ETSI EN 319 412-5 V2.2.0 (2017-08)
id-etsi-qcs-QcSSCD OBJECT IDENTIFIER ::= { id-etsi-qcs 4 }
4.2.3 QCStatement claiming that the certificate is a EU qualified
certificate of a particular type
This QCStatement declares that a certificate is issued as one and only one of the purposes of electronic signature,
electronic seal or web site authentication.
This QCStatements states that an EU qualified certificate is issued as one specific types according to Annexes I, III or
IV of the Regulation (EU) No 910/2014 [i.8] when used in combination with the qcStatement as defined in clause 4.2.1.
When used on its own it indicates that it is used for the purposes of electronic signatures, seals or web sites for "non-
qualified certificates" within the context of Regulation (EU) No 910/2014 [i.8].
NOTE: This statement, without the one defined in clause 4.2.1, can be potentially used in other regulatory
environments which use electronic signature, electronic seal or web site with the same meaning.
Syntax:
esi4-qcStatement-6 QC-STATEMENT ::= { SYNTAX QcType IDENTIFIED
BY id-etsi-qcs-QcType }
Id-etsi-qcs-QcType OBJECT IDENTIFIER ::= { id-etsi-qcs 6 }
QcType::= SEQUENCE OF OBJECT IDENTIFIER (id-etsi-qct-esign | id-etsi-qct-eseal |
id-etsi-qct-web
...
SLOVENSKI STANDARD
oSIST prEN 319 412-5 V2.2.0:2017
01-november-2017
Elektronski podpisi in infrastruktura (ESI) - Profili potrdil - 5. del: Izjave QC
Electronic Signatures and Infrastructures (ESI) - Certificate Profiles - Part 5:
QCStatements
Ta slovenski standard je istoveten z: ETSI EN 319 412-5 V2.2.0 (2017-08)
ICS:
03.080.99 Druge storitve Other services
35.030 Informacijska varnost IT Security
oSIST prEN 319 412-5 V2.2.0:2017 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 319 412-5 V2.2.0:2017
---------------------- Page: 2 ----------------------
oSIST prEN 319 412-5 V2.2.0:2017
Draft ETSI EN 319 412-5 V2.2.0 (2017-08)
EUROPEAN STANDARD
Electronic Signatures and Infrastructures (ESI);
Certificate Profiles;
Part 5: QCStatements
---------------------- Page: 3 ----------------------
oSIST prEN 319 412-5 V2.2.0:2017
2 Draft ETSI EN 319 412-5 V2.2.0 (2017-08)
Reference
REN/ESI-0019412-5v221
Keywords
e-commerce, electronic signature, security, trust
services
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2017.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
GSM® and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 319 412-5 V2.2.0:2017
3 Draft ETSI EN 319 412-5 V2.2.0 (2017-08)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 4
Introduction . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions and abbreviations . 7
3.1 Definitions . 7
3.2 Abbreviations . 7
4 Qualified certificate statements . 8
4.1 General requirements . 8
4.2 QCStatements claiming compliance with the EU legislation . 8
4.2.1 QCStatement claiming that the certificate is a EU qualified certificate . 8
4.2.2 QCStatement claiming that the private key related to the certified public key resides in a QSCD . 8
4.2.3 QCStatement claiming that the certificate is a EU qualified certificate of a particular type . 9
4.3 Generic QCStatements . 9
4.3.1 Introduction. 9
4.3.2 QCStatement regarding limits on the value of transactions . 9
4.3.3 QCStatement indicating the duration of the retention period of material information . 10
4.3.4 QCStatement regarding location of PKI Disclosure Statements (PDS) . 10
5 Requirements on QCStatements in EU qualified certificates . 11
Annex A (informative): Relationship with the Regulation (EU) No 910/2014 . 12
A.1 EU qualified certificates for electronic signatures . 12
A.2 EU qualified certificates for electronic seals . 13
A.3 EU qualified certificates for website authentication . 14
Annex B (normative): ASN.1 declarations. 15
Annex C (informative): Change History . 17
History . 18
ETSI
---------------------- Page: 5 ----------------------
oSIST prEN 319 412-5 V2.2.0:2017
4 Draft ETSI EN 319 412-5 V2.2.0 (2017-08)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft European Standard (EN) has been produced by ETSI Technical Committee Electronic Signatures and
Infrastructures (ESI), and is now submitted for the combined Public Enquiry and Vote phase of the ETSI standards EN
Approval Procedure.
The present document is part 5 of multi-part deliverable covering the Certificates Profiles. Full details of the entire
series can be found in part 1 [i.1].
The present document was previously published as ETSI TS 101 862 [i.4].
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 6 months after doa
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 6 ----------------------
oSIST prEN 319 412-5 V2.2.0:2017
5 Draft ETSI EN 319 412-5 V2.2.0 (2017-08)
Introduction
ITU and ISO issued standards for certification of public keys in Recommendation ITU-T X.509 | ISO/IEC 9594-8 [i.7]
which are used for the security of communications and data for a wide range of electronic applications.
The IETF qualified certificate profile, IETF RFC 3739 [2] defines an extension to X.509 certificates, the
qcStatements extension, which can include statements relevant for qualified certificates. IETF RFC 3739 [2]
defines qualified certificates in a general context as "a certificate whose primary purpose is to identify a person with a
high level of assurance, where the certificate meets some qualification requirements defined by an applicable legal
framework". The use of IETF RFC 3739 [2] qcStatements in the present document goes beyond the scope of the
RFC which is directed at natural persons only.
The qcStatements certificate extension can contain any statement by the certificate issuer that can be useful to the
relying party in determining the applicability of the certificate for an intended usage. Such statement can be a
declaration that the certificate fulfils specific legal requirements for qualified certificates according to a defined legal
framework.
The present document is aiming to meet the general requirements of the international community to provide trust and
confidence in electronic transactions including, amongst others, applicable requirements from Regulation (EU)
No 910/2014 [i.8] Annexes I, III and IV.
ETSI
---------------------- Page: 7 ----------------------
oSIST prEN 319 412-5 V2.2.0:2017
6 Draft ETSI EN 319 412-5 V2.2.0 (2017-08)
1 Scope
The present document defines specific QCStatement for the qcStatements extension as defined in IETF
RFC 3739 [2], clause 3.2.6, including requirements for their use in EU qualified certificates. Some of these
QCStatements can be used for other forms of certificate.
The QCStatements defined in the present document can be used in combination with any certificate profile, either
defined in ETSI EN 319 412-2 [i.2], ETSI EN 319 412-3 [i.5] and ETSI EN 319 412-4 [i.6], or defined elsewhere.
The QCStatements defined in clause 4.3 may be applied to regulatory environments outside the EU. Other
requirements specified in clause 4 are specific to Regulation (EU) No 910/2014 [i.8] but may be adapted for other
regulatory environments.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ISO 639-1:2002: "Codes for the representation of names of languages -- Part 1: Alpha-2 code".
[2] IETF RFC 3739: "Internet X.509 Public Key Infrastructure: Qualified Certificates Profile".
[3] Recommendation ITU-T X.680-X.699: "Information technology - Abstract Syntax Notation One
(ASN.1)".
[4] ISO 4217: "Codes for the representation of currencies and funds".
[5] IETF RFC 2818: "HTTP Over TLS".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI EN 319 412-1: "Electronic Signatures and Infrastructures (ESI); Certificate Profiles;
Part 1: Overview and common data structures".
[i.2] ETSI EN 319 412-2: "Electronic Signatures and Infrastructures (ESI); Certificate Profiles;
Part 2: Certificate Profile for certificates issued to natural persons".
[i.3] Directive 1999/93/EC of the European Parliament and of the Council of 13 December 1999 on a
Community framework for electronic signatures.
ETSI
---------------------- Page: 8 ----------------------
oSIST prEN 319 412-5 V2.2.0:2017
7 Draft ETSI EN 319 412-5 V2.2.0 (2017-08)
[i.4] ETSI TS 101 862: "Qualified Certificate profile".
[i.5] ETSI EN 319 412-3: "Electronic Signatures and Infrastructures (ESI); Certificate Profiles;
Part 3: Certificate Profile for certificates issued to legal persons".
[i.6] ETSI EN 319 412-4: "Electronic Signatures and Infrastructures (ESI); Certificate Profiles;
Part 4: Certificate profile for web site certificates".
[i.7] Recommendation ITU-T X.509 | ISO/IEC 9594-8: "Information technology - Open systems
interconnection - The Directory: Public-key and attribute certificate frameworks".
[i.8] Regulation (EU) No 910/2014 of the European Parliament and of the Council on electronic
identification and trust services for electronic transactions in the internal market and repealing
Directive 1999/93/EC.
[i.9] IETF RFC 5280: "Internet X.509 Public Key Infrastructure Certificate and Certificate Revocation
List (CRL) Profile".
[i.10] ETSI EN 319 411-1: "Electronic Signatures and Infrastructures (ESI); Policy and security
requirements for Trust Service Providers issuing certificates; Part 1: General requirements".
[i.11] CA/Browser Forum: "Baseline Requirements for the Issuance and Management of Publicly-
Trusted Certificates".
[i.12] CA/Browser Forum: "Guidelines for The Issuance and Management of Extended Validation
Certificates".
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in ETSI EN 319 412-1 [i.1] and the following
apply:
EU qualified certificate: qualified certificate that is stated to be in accordance with Annex I, III or IV of the Regulation
(EU) No 910/2014 [i.8] or Annex I of the Directive 1999/93/EC [i.3] whichever is in force at the time of issuance
QCStatement: statement for inclusion in a qcStatements certificates extension as specified in IETF RFC 3739 [2]
qualified electronic signature/seal creation device: As specified in Regulation (EU) No 910/2014 [i.8].
secure signature creation device: As specified in Directive 1999/93 [i.3].
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
ASN.1 Abstract Syntax Notation One
CA Certification Authority
CRL Certificate Revocation List
EC European Commission
EU European Union
IETF Internet Engineering Task Force
ISO International Organization for Standardization
PDS PKI Disclosure Statements
PKI Public Key Infrastructure
QC Qualified Certificate
QSCD Qualified electronic Signature/Seal Creation Device
RFC Request For Comments
URL Uniform Resource Locator
ETSI
---------------------- Page: 9 ----------------------
oSIST prEN 319 412-5 V2.2.0:2017
8 Draft ETSI EN 319 412-5 V2.2.0 (2017-08)
4 Qualified certificate statements
4.1 General requirements
The qcStatements extension shall be as specified in clause 3.2.6 of IETF RFC 3739 [2]. The qcStatements
extension shall not be marked as critical.
The following clauses define a number of individual QCStatements to be included in the qcStatements
extension.
The syntax of the defined statements shall comply with ASN.1 [3]. The complete ASN.1 module for all defined
statements shall be as provided in Annex B; it takes precedence over the ASN.1 definitions provided in the body of the
present document, in case of discrepancy.
NOTE: This extension is not processed as part of IETF RFC 5280 [i.9] path validation and there are no security
implications with accepting a certificate in a system that cannot parse this extension.
4.2 QCStatements claiming compliance with the EU
legislation
4.2.1 QCStatement claiming that the certificate is a EU qualified
certificate
This Qcstatement claims that the certificate is an EU qualified certificate that is issued according to Directive
1999/93/EC [i.3] or the Annex I, III or IV of the Regulation (EU) No 910/2014 [i.8] whichever is in force at the time of
issuance.
Syntax:
esi4-qcStatement-1 QC-STATEMENT ::= { IDENTIFIED BY id-etsi-qcs-QcCompliance }
id-etsi-qcs-QcCompliance OBJECT IDENTIFIER ::= { id-etsi-qcs 1 }
The precise meaning of this statement is enhanced by the QC type statement defined in clause 4.2.3 according to the
table 1.
Table 1: esi4-qcStatement-1 meaning
QC type statement Meaning of this statement (esi4-qcStatement-1)
(clause 4.2.3)
Absent The certificate is issued according to Directive 1999/93/EC [i.3] or Annex I of the Regulation
(EU) No 910/2014 [i.8] (for electronic signatures).
Present The certificate is issued according to Annex I, III or IV of Regulation (EU) No 910/2014 [i.8]
as of the types declared by the QC type statement in accordance with clause 4.2.3.
A certificate that includes this statement shall comply with all requirements defined in clause 5.
4.2.2 QCStatement claiming that the private key related to the certified
public key resides in a QSCD
This Qcstatement declares that the private key related to the certified public key resides in a Qualified
Signature/Seal Creation Device (QSCD) according to the Regulation (EU) No 910/2014 [i.8] or a secure signature
creation device as defined in the Directive 1999/93/EC [i.3].
Syntax:
esi4-qcStatement-4 QC-STATEMENT ::= { IDENTIFIED BY id-etsi-qcs-QcSSCD }
ETSI
---------------------- Page: 10 ----------------------
oSIST prEN 319 412-5 V2.2.0:2017
9 Draft ETSI EN 319 412-5 V2.2.0 (2017-08)
id-etsi-qcs-QcSSCD OBJECT IDENTIFIER ::= { id-etsi-qcs 4 }
4.2.3 QCStatement claiming that the certificate is a EU qualified
certificate of a particular type
This QCStatement declares that a certificate is issued as one and only one of the purposes of electronic signature,
electronic seal or web site authentication.
This QCStatements states that an EU qualified certificate is issued as one specific types according to Annexes I, III or
IV of the Regulation (EU) No 910/2014 [i.8] when used in combination with the qcStatement as defined in clause 4.2.1.
When used on its own it indicates that it is used for the purposes of electronic signatures, seals or web sites for "non-
qualified certificates" within the context of Regulation (EU) No 910/2014 [i.8].
NOTE: This statement, without the one defined in clause 4.2.1, can be potentially used in other regulatory
environments which use electronic sig
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.