oSIST prEN 16361:2019
(Main)Power operated pedestrian doorsets - Product standard, performance characteristics - Pedestrian doorsets, other than swing type, initially designed for installation with power operation
Power operated pedestrian doorsets - Product standard, performance characteristics - Pedestrian doorsets, other than swing type, initially designed for installation with power operation
This document specifies requirements and test/assessment/calculation methods for power operated pedestrian doorsets, other than swing type, initially designed for installation with power operation.
Such doorset constructions can be operated electro-mechanically, electro-hydraulically or pneumatically.
These doorsets include power operated pedestrian sliding doorsets, revolving doorsets, balanced (sliding/swing) doorsets and folding doorsets with one or more horizontally moving leaves.
This document applies to power operated pedestrian doorsets with flush or panelled leaves, complete with:
— integral fanlights, if any;
NOTE 1 A fanlight is a panel over a door, which is part of the doorset.
— side panels that are contained within a single frame for inclusion in a single aperture, if any.
The intended uses of the products covered by this document are:
— doorsets with or without fire resistance and smoke control characteristics for external use in escape routes and other declared specific uses and/or uses subject to other specific requirements, in particular noise, energy and tightness in construction works;
— doorsets with or without fire resistance and smoke control characteristics for internal use in escape routes, communication and other declared specific uses and/or uses subject to other specific requirements, in particular noise in construction works;
— doorsets with or without fire resistance and smoke control characteristics for internal use in escape routes, communication and other declared specific uses and/or uses subject to other specific requirements, in particular noise and energy in construction works.
The products covered by this document are not assessed for structural applications of the building.
This document does not cover operation in environments where the electromagnetic disturbances are outside the range of those specified in EN 61000-6-2.
This document does not apply to:
— external pedestrian doorsets according to EN 14351-1;
— internal pedestrian doorsets according to EN 14351-2;
— lifts doorsets;
— vehicles doorsets;
— doorsets used in industrial processes;
— doorsets in partition walls;
— doorsets outside the reach of people (such as crane gantry fences);
— pedestrian entrance control equipment such as turnstiles, swing lanes and retractable lanes;
— platform doorsets.
This document does not cover special functions of doorsets (e.g. security).
Kraftbetätigte Türen - Produktnorm, Leistungseigenschaften - Türsysteme, mit Ausnahme von Drehflügeltüren, vorgesehen für den kraftbetätigten Betrieb
Dieses Dokument legt Anforderungen an sowie Verfahren zur Prüfung/Beurteilung/Berechnung von kraftbetätigten Türen, mit Ausnahme von Drehflügeltüren, vorgesehen für den kraftbetätigten Betrieb fest.
Derartige Türkonstruktionen können elektromechanisch, elektrohydraulisch oder pneumatisch betrieben werden.
Diese Türsysteme umfassen automatische Schiebe- und Karusselltüren, Drehschiebetüren, sowie Faltflügeltüren mit einem oder mehreren horizontal bewegten Flügeln.
Dieses Dokument gilt für kraftbetätigte Türen mit Sperr- oder Füllungstürblättern, ergänzt mit:
- integrierten Oberlichtern, sofern vorhanden;
ANMERKUNG Ein Oberlicht ist eine Ausfachung über einer Tür, die Teil des Türsystems ist.
- Seitenteilen, sofern vorhanden, in einem einzigen (gemeinsamen) Rahmen oder Zarge zum Einbau in eine gemeinsame Öffnung.
Die vorgesehenen Anwendungen der in diesem Dokument behandelten Produkte sind:
- Außentüren mit oder ohne Merkmale zur Feuerwiderstandsfähigkeit und zum Rauchschutz in Fluchtwegen und weitere angegebene besondere Verwendungen und/oder Verwendungen, die anderen spezifischen Anforderungen unterliegen, vor allem an Geräusche, Energie und Dichtheit in Bauwerken;
- Innentüren mit oder ohne Merkmale zu Feuerwiderstandsfähigkeit und zum Rauchschutz in Fluchtwegen, Verbindungen und weitere angegebene besondere Verwendungen und/oder Verwendungen, die anderen spezifischen Anforderungen unterliegen, vor allem an Geräusche in Bauwerken;
- Innentüren mit oder ohne Merkmale zu Feuerwiderstandsfähigkeit und zum Rauchschutz in Fluchtwegen, Verbindungen und weitere angegebene besondere Verwendungen und/oder Verwendungen, die anderen spezifischen Anforderungen unterliegen, vor allem an Geräusche und Energie in Bauwerken.
Die in diesem Dokument beschriebenen Produkte sind nicht für eine Anwendung als tragende Bauteile eines Gebäudes geeignet.
Dieses Dokument umfasst keinen Einsatz in Umgebungen, in denen elektromagnetische Störungen außerhalb des in EN 61000-6-2 festgelegten Bereiches liegen.
Dieses Dokument gilt nicht für:
- Außentüren nach EN 14351-1;
- Innentüren nach EN 14351-2;
- Aufzugtüren;
- Fahrzeugtüren;
- Türen für den Einsatz in industriellen Prozessen;
- Trennwände;
- Türen und Tore außerhalb der Reichweite von Personen (z. B. Schutzgitter für Portalkrane);
- Zugangskontrolleinrichtungen wie Drehkreuze, Schwenktüren und versenkbare Türen;
- Bahnsteigtüren.
Dieses Dokument behandelt keine spezifischen Funktionen von Türsystemen (wie z. B. Sicherheit).
Blocs-portes motorisés pour piétons - Norme de produit, caractéristiques de performance - Blocs-portes pour piétons, autres que de type battant, initialement conçus pour une installation avec un système de motorisation
Le présent document spécifie les exigences et les méthodes d’essai/d’évaluation/de calcul pour les blocs-portes motorisés pour piétons, autres que de type battant, initialement conçus pour une installation avec un système de motorisation.
Ces constructions de bloc-porte peuvent être actionnées de manière électromécanique, électrohydraulique ou pneumatique.
Ces blocs-portes comprennent les blocs-portes motorisés pour piétons coulissants, tournants, éclipsables (coulissant/pivotant) et pliants avec un ou plusieurs vantaux se déplaçant horizontalement.
Le présent document s’applique aux blocs-portes motorisés pour piétons à vantaux plans ou menuisés, complétés :
- d’impostes, le cas échéant ;
NOTE Une imposte est un panneau situé au-dessus de la porte qui fait partie du bloc-porte.
- de panneaux latéraux qui sont intégrés dans un châssis individuel afin d’être installés dans une seule ouverture, le cas échéant.
Les usages prévus des produits couverts par le présent document sont :
- les blocs-portes avec ou sans caractéristiques de résistance au feu et d’étanchéité aux fumées pour une utilisation extérieure en issues de secours et autres usages spécifiques déclarés et/ou usages soumis à d’autres exigences spécifiques, en particulier au bruit, à l’énergie et à l’étanchéité dans les ouvrages de construction ;
- les blocs-portes avec ou sans caractéristiques de résistance au feu et d’étanchéité aux fumées pour une utilisation intérieure en issues de secours, en communication et autres usages spécifiques déclarés et/ou usages soumis à d’autres exigences spécifiques, en particulier au bruit dans les ouvrages de construction ;
- les blocs-portes avec ou sans caractéristiques de résistance au feu et d’étanchéité aux fumées pour une utilisation intérieure en issues de secours, en communication et autres usages spécifiques déclarés et/ou usages soumis à d’autres exigences spécifiques, en particulier au bruit et à l’énergie dans les ouvrages de construction.
Les produits couverts par le présent document ne sont pas destinés à des applications structurelles.
Le présent document ne couvre pas l’exploitation dans des environnements où les perturbations électromagnétiques sont hors de la plage spécifiée dans l’EN 61000-6-2.
Le présent document ne s’applique pas aux :
- blocs-portes extérieurs pour piétons qui relèvent de l’EN 14351-1 ;
- blocs-portes intérieurs pour piétons qui relèvent de l’EN 14351-2 ;
- blocs-portes d’ascenseurs ;
- blocs-portes de véhicules ;
- blocs-portes utilisés dans des procédés industriels ;
- blocs-portes dans des cloisons ;
- blocs-portes hors d’atteinte des personnes (comme les barrières sur les portiques de grue) ;
- équipements de contrôle d’accès pour piétons tels que les tourniquets, les portillons battants et les portillons télescopiques ;
- blocs-portes paliers de quai.
Le présent document ne couvre pas les fonctions spéciales des blocs-portes (par exemple la sécurité).
Avtomatska vrata za prehod ljudi - Standard za proizvod, zahtevane lastnosti - Sestavi vrat za prehod ljudi, razen nihajnih vrat, najprej zasnovani za montažo s pogonom
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN 16361:2019
01-maj-2019
Avtomatska vrata za prehod ljudi - Standard za proizvod, zahtevane lastnosti -
Sestavi vrat za prehod ljudi, razen nihajnih vrat, najprej zasnovani za montažo s
pogonom
Power operated pedestrian doorsets - Product standard, performance characteristics -
Pedestrian doorsets, other than swing type, initially designed for installation with power
operation
Kraftbetätigte Türen - Produktnorm, Leistungseigenschaften - Türsysteme, mit
Ausnahme von Drehflügeltüren, vorgesehen für den kraftbetätigten Betrieb
Blocs-portes motorisés pour piétons - Norme de produit, caractéristiques de performance
- Blocs-portes pour piétons, autres que de type battant, initialement conçus pour une
installation avec un système de motorisation
Ta slovenski standard je istoveten z: prEN 16361
ICS:
91.060.50 Vrata in okna Doors and windows
oSIST prEN 16361:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 16361:2019
---------------------- Page: 2 ----------------------
oSIST prEN 16361:2019
DRAFT
EUROPEAN STANDARD
prEN 16361
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2019
ICS 91.060.50 Will supersede EN 16361:2013+A1:2016
English Version
Power operated pedestrian doorsets - Product standard,
performance characteristics - Pedestrian doorsets, other
than swing type, initially designed for installation with
power operation
Blocs-portes motorisés pour piétons - Norme de Kraftbetätigte Türen - Produktnorm,
produit, caractéristiques de performance - Blocs- Leistungseigenschaften - Türsysteme, mit Ausnahme
portes pour piétons, autres que de type battant, von Drehflügeltüren, vorgesehen für den
initialement conçus pour une installation avec un kraftbetätigten Betrieb
système de motorisation
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 33.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 16361:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 16361:2019
prEN 16361:2019 (E)
Contents Page
European foreword . 5
1 Scope . 6
2 Normative references . 7
3 Terms and definitions . 9
4 Products characteristics . 9
4.1 General . 9
4.2 Impact resistance (only for glazed doors with injury risks) . 10
4.3 Direct airborne sound insulation index (only for uses where acoustic performance is
declared) . 10
4.4 Operating forces (safety in use) (only for automatic devices) . 10
4.5 Water tightness (only for external doors) . 10
4.6 Resistance to wind load (only for external doors) . 11
4.7 Thermal transmittance (only for external doors and for internal doors where the
thermal insulation is declared). 11
4.8 Air permeability (only for external doors and for internal doors where thermal
insulation is declared) . 12
4.9 Radiation properties . 14
4.10 Resistance to fire (for fire compartmentation uses) . 14
4.11 Smoke control (only for applications where limitation of smoke spread is required) . 14
4.12 Ability to release. 14
4.13 Self-closing (only for self-closing fire resistant and/or smoke control doorsets) . 15
4.14 Durability . 15
4.14.1 General . 15
4.14.2 Durability of operating forces (safety in use) (only for automatic devices) . 15
4.14.3 Durability of the ability to release . 16
4.14.4 Durability of self-closing against degradation (cycle testing) (only for self-closing
doorsets) . 16
4.15 Electromagnetic compatibility (EMC) . 16
4.16 Other requirements . 16
4.16.1 Glazing . 16
4.16.2 Unframed glass doorsets . 16
4.16.3 Emergency opening (only applicable to doorsets in escape routes and emergency
exits) . 17
4.16.4 Burglar resistance . 17
5 Testing, assessment and sampling methods . 17
5.1 General . 17
5.2 Impact resistance (only for glazed doors with injury risks) . 17
5.3 Direct airborne sound insulation index (only for uses where acoustic performance is
declared) . 17
5.4 Operating forces (safety in use) (only for automatic devices) . 17
5.5 Water tightness (only for external doors) . 17
5.6 Resistance to wind load (only for external doors) . 17
5.7 Thermal transmittance (only for external doors and for internal doors where
thermal insulation is declared). 17
5.8 Air permeability (only for external doors and for internal doors where thermal
insulation is declared) . 18
5.9 Radiation properties . 18
2
---------------------- Page: 4 ----------------------
oSIST prEN 16361:2019
prEN 16361:2019 (E)
5.10 Resistance to fire (for fire compartmentation uses) . 18
5.11 Smoke control (only for applications where limitation of smoke spread is required) . 18
5.12 Ability to release . 18
5.13 Self-closing . 18
5.14 Durability . 19
5.14.1 General . 19
5.14.2 Durability of operating forces (safety in use) (only for automatic devices). 19
5.14.3 Durability of the ability to release and of self-closing (only for self-closing doorsets)
against degradation (cycle testing) . 19
5.15 Electromagnetic compatibility (EMC) . 19
5.15.1 Verification . 19
5.15.2 Test for electromagnetic emissions . 19
5.15.3 Tests for immunity to disturbances . 19
5.16 Other requirements . 20
5.16.1 Glazing . 20
5.16.2 Unframed glass doorsets. 20
5.16.3 Emergency opening . 20
5.16.4 Burglar resistance . 20
6 Assessment and verification of constancy of performance – AVCP . 20
6.1 General . 20
6.2 Type testing . 20
6.2.1 General . 20
6.2.2 Test samples, testing and compliance criteria . 21
6.2.3 Test reports . 22
6.2.4 Shared other party results . 23
6.2.5 Cascading determination of the product type results . 23
6.3 Factory production control (FPC) . 24
6.3.1 General . 24
6.3.2 Requirements . 25
6.3.3 Product specific requirements . 28
6.3.4 Initial inspection of factory and of FPC . 28
6.3.5 Continuous surveillance of FPC for products covered by AVCP system 1 . 29
6.3.6 Procedure for modifications . 29
6.3.7 One-off products, pre-production products (e.g. prototypes) and products produced
in very low quantity . 29
Annex A (normative) Standards on glass . 31
Annex B (informative) Summary of the characteristics . 32
B.1 Summary of the characteristics of power operated pedestrian doorsets, other than
swing type, initially designed for installation with power operation . 32
Annex C (informative) Handling, installation, maintenance and care . 34
Annex D (informative) Summary of classification of characteristics . 35
Annex E (informative) Example of air permeability calculation . 42
Annex F (normative) Pre-test conditioning . 44
F.1 General . 44
F.2 Before the resistance to fire test . 44
F.2.1 General . 44
F.2.2 Shakedown conditioning . 44
Annex ZA (informative) Relationship of this European Standard with Regulation (EU)
No. 305/2011 . 45
3
---------------------- Page: 5 ----------------------
oSIST prEN 16361:2019
prEN 16361:2019 (E)
Annex ZB (informative) Relationship between this European standard and the essential
requirements of Directive 2014/30/EU [2014 OJ L96] aimed to be covered . 52
Bibliography . 53
4
---------------------- Page: 6 ----------------------
oSIST prEN 16361:2019
prEN 16361:2019 (E)
European foreword
This document (prEN 16361:2019) has been prepared by Technical Committee CEN/TC 33 “Doors,
windows, shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 16361:2013+A1:2016.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive 2014/30/EU
and Regulation (EU) 305/2011.
For relationship with EU Directive 2014/30/EU and Regulation (EU) 305/2011, see informative
Annexes ZA and ZB, which are an integral part of this document.
Compared with EN 16361:2013+A1:2016, the following changes have been made:
— relevant requirements and definitions from EN 16034 relevant to fire and smoke characteristics
have been incorporated in this document and subclauses number has been consequently updated;
— title of Clause 4 has been changed to comply with the model standard;
— subclause 4.4 “Height” has been deleted;
— subclause 4.4 has been modified to align with Mandate M/101;
— subclause 4.16.3 (previous 4.14.3) Emergency opening (only applicable to doorsets in escape
routes and emergency exits) has been updated;
— Clause 6 has been updated to CPR requirements;
— Annex ZA has been updated to CPR requirements;
— editorial changes in the text.
5
---------------------- Page: 7 ----------------------
oSIST prEN 16361:2019
prEN 16361:2019 (E)
1 Scope
This document specifies requirements and test/assessment/calculation methods for power operated
pedestrian doorsets, other than swing type, initially designed for installation with power operation.
Such doorset constructions can be operated electro-mechanically, electro-hydraulically or
pneumatically.
These doorsets include power operated pedestrian sliding doorsets, revolving doorsets, balanced
(sliding/swing) doorsets and folding doorsets with one or more horizontally moving leaves.
This document applies to power operated pedestrian doorsets with flush or panelled leaves, complete
with:
— integral fanlights, if any;
NOTE A fanlight is a panel over a door, which is part of the doorset.
— side panels that are contained within a single frame for inclusion in a single aperture, if any.
The intended uses of the products covered by this document are:
— doorsets with or without fire resistance and smoke control characteristics for external use in
escape routes and other declared specific uses and/or uses subject to other specific requirements,
in particular noise, energy and tightness in construction works;
— doorsets with or without fire resistance and smoke control characteristics for internal use in escape
routes, communication and other declared specific uses and/or uses subject to other specific
requirements, in particular noise in construction works;
— doorsets with or without fire resistance and smoke control characteristics for internal use in escape
routes, communication and other declared specific uses and/or uses subject to other specific
requirements, in particular noise and energy in construction works.
The products covered by this document are not assessed for structural applications of the building.
This document does not cover operation in environments where the electromagnetic disturbances are
outside the range of those specified in EN 61000-6-2.
This document does not apply to:
— external pedestrian doorsets according to EN 14351-1;
— internal pedestrian doorsets according to EN 14351-2;
— lifts doorsets;
— vehicles doorsets;
— doorsets used in industrial processes;
— doorsets in partition walls;
— doorsets outside the reach of people (such as crane gantry fences);
— pedestrian entrance control equipment such as turnstiles, swing lanes and retractable lanes;
— platform doorsets.
This document does not cover special functions of doorsets (e.g. security).
6
---------------------- Page: 8 ----------------------
oSIST prEN 16361:2019
prEN 16361:2019 (E)
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 572-9, Glass in building — Basic soda lime silicate glass products — Part 9: Evaluation of
conformity/Product standard
EN 1026:2016, Windows and doors — Air permeability — Test method
EN 1027:2016, Windows and doors — Water tightness — Test method
EN 1096-4, Glass in building — Coated glass — Part 4: Product standard
EN 1279-5, Glass in building — Insulating glass units — Part 5: Product standard
EN 1627, Pedestrian doorsets, windows, curtain walling, grilles and shutters — Burglar resistance —
Requirements and classification
EN 1634-1:2014+A1:2018, Fire resistance and smoke control tests for door and shutter assemblies,
openable windows and elements of building hardware — Part 1: Fire resistance test for door and shutter
assemblies and openable windows
EN 1634-3:2004, Fire resistance and smoke control tests for door and shutter assemblies, openable
windows and elements of building hardware — Part 3: Smoke control test for door and shutter assemblies
EN 1748-1-2, Glass in building — Special basic products — Borosilicate glasses — Part 1-2: Evaluation of
conformity/Product standard
EN 1748-2-2, Glass in building — Special basic products — Glass ceramics — Part 2-2: Evaluation of
conformity/Product standard
EN 1863-2, Glass in building — Heat strengthened soda lime silicate glass — Part 2: Evaluation of
conformity/Product standard
EN 12150-2, Glass in building — Thermally toughened soda lime silicate safety glass — Part 2: Evaluation
of conformity/Product standard
EN 12207:2016, Windows and doors — Air permeability — Classification
EN 12208:1999, Windows and doors — Watertightness — Classification
EN 12210:2016, Windows and doors — Resistance to wind load — Classification
EN 12211:2016, Windows and doors — Resistance to wind load — Test method
EN 12337-2, Glass in building — Chemically strengthened soda lime silicate glass — Part 2: Evaluation of
conformity/Product standard
EN 12519:2018, Windows and pedestrian doors — Terminology
EN 13024-2, Glass in building — Thermally toughened borosilicate safety glass — Part 2: Evaluation of
conformity/Product standard
EN 13049, Windows — Soft and heavy body impact — Test method, safety requirements and classification
7
---------------------- Page: 9 ----------------------
oSIST prEN 16361:2019
prEN 16361:2019 (E)
EN 14178-2, Glass in building — Basic alkaline earth silicate glass products — Part 2: Evaluation of
conformity/Product standard
EN 14179-2, Glass in building — Heat soaked thermally toughened soda lime silicate safety glass — Part
2: Evaluation of conformity/Product standard
EN 14321-2, Glass in building — Thermally toughened alkaline earth silicate safety glass — Part 2:
Evaluation of conformity/Product standard
EN 14351-1:2006+A2:2016, Windows and doors — Product standard, performance characteristics —
Part 1: Windows and external pedestrian doorsets
EN 16005:2012, Power operated pedestrian doorsets — Safety in use — Requirements and test methods
EN 61000-6-2, Electromagnetic compatibility (EMC) — Part 6-2: Generic standards — Immunity for
industrial environments (IEC 61000-6-2)
EN 61000-6-3, Electromagnetic compatibility (EMC) — Part 6-3: Generic standards — Emission standard
for residential, commercial and light-industrial environments (IEC 61000-6-3)
EN ISO 717-1, Acoustics — Rating of sound insulation in buildings and of building elements — Part 1:
Airborne sound insulation (ISO 717-1)
EN ISO 10077-1:2017, Thermal performance of windows, doors and shutters — Calculation of thermal
transmittance — Part 1: General (ISO 10077-1:2017)
EN ISO 10077-2, Thermal performance of windows, doors and shutters — Calculation of thermal
transmittance — Part 2: Numerical method for frames (ISO 10077-2)
EN ISO 10140-2, Acoustics — Laboratory measurement of sound insulation of building elements — Part 2:
Measurement of airborne sound insulation (ISO 10140-2)
EN ISO 12543-2, Glass in building — Laminated glass and laminated safety glass — Part 2: Laminated
safety glass (ISO 12543-2)
EN ISO 12567-1, Thermal performance of windows and doors — Determination of thermal transmittance
by the hot-box method — Part 1: Complete windows and doors (ISO 12567-1)
EN ISO 13849-1, Safety of machinery - Safety-related parts of control systems - Part 1: General principles
for design (ISO 13849-1)
8
---------------------- Page: 10 ----------------------
oSIST prEN 16361:2019
prEN 16361:2019 (E)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in EN 16005:2012, EN 12519:2018,
EN 14351-1:2006+A2:2016 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1
power operated pedestrian doorset
doorset for pedestrian passage only with one or more leaves that is moved, at least in one direction, by
an external energy supply (e.g. electrically) instead of manual or stored mechanical energy; including
drive, leaves, side panel(s), vision panel(s), flush over panel(s), transom panel(s) and/or glazing,
building hardware, seals, protective devices and any components needed for its safe operation
[SOURCE: EN 16005 modified]
3.2
night shield
additional element to close the entrance of a revolving doorset
3.3
self-closing
ability of an open doorset to fully close, without human intervention, into its frame and engage any
fitted latching device
3.4
ability to release
release of the hold-open device of a doorset to ensure reliable closing of the doorset
3.5
friable material
material which could crumble, slump, drop or shake down during the normal life of a doorset
EXAMPLES Loose infill mineral fibre, loose materials filled in or blown in the door leaf and gypsum boards.
Note 1 to entry: Gypsum plasterboards, mineral fibre boards with adhesive binder and silicate fibre boards are
not considered to be friable.
4 Products characteristics
4.1 General
The performance characteristics for power operated pedestrian doorsets, other than swing type,
initially designed for installation with power operation shall be determined and expressed in
accordance with 4.2 to 4.16.
NOTE 1 The order in which the performance characteristics are identified does not imply an order of priority
or a test sequence.
The performance characteristics of 4.2, 4.4, 4.6 to 4.9 and the burglar resistance of 4.16.4 shall be
determined with closed and locked doorsets; for revolving doorsets with night shield this shall be
closed.
9
---------------------- Page: 11 ----------------------
oSIST prEN 16361:2019
prEN 16361:2019 (E)
NOTE 2 Without night shield most of the following requirements are not applicable to revolving doorsets due
to requirements of safety in use (e.g. safety distances).
For revolving doorsets the external side is the part of the doorset which is exposed to the weather.
4.2 Impact resistance (only for glazed doors with injury risks)
Impact resistance is the ability of a doorset to keep in place the glazing without creating hazards in case
of impact with a body.
Th
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.