iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

oSIST prEN ISO 5459:2024

(Main)

Geometrical product specifications (GPS) - Geometrical tolerancing - Datums and datum systems (ISO/FDIS 5459:2024)

Geometrical product specifications (GPS) - Geometrical tolerancing - Datums and datum systems (ISO/FDIS 5459:2024)

ISO 5459:2011 specifies terminology, rules and methodology for the indication and understanding of datums and datum systems in technical product documentation. It also provides explanations to assist the user in understanding the concepts involved.
ISO 5459:2011 defines the specification operator (see ISO 17450-2) used to establish a datum or datum system. The verification operator (see ISO 17450-2) can take different forms (physically or mathematically) and is not the subject of ISO 5459:2011.
The detailed rules for maximum and least material requirements for datums are given in ISO 2692.

Geometrische Produktspezifikation (GPS) - Geometrische Tolerierung - Bezüge und Bezugssysteme (ISO/FDIS 5459:2024)

Dieses Dokument legt die Terminologie, die Regeln und die Methodik zur Angabe und zum Verständnis von Bezügen und Bezugssystemen in technischen Produktdokumentationen fest. Darüber hinaus stellt dieses Dokument Erklärungen zur Verfügung, um den Anwender dabei zu unterstützen, die zugrunde liegenden Konzepte zu verstehen.
Dieses Dokument legt den Spezifikationsoperator (siehe ISO 17450 2) fest, der zur Bildung eines Bezugs oder Bezugssystems verwendet wird. Der Verifikationsoperator (siehe ISO 17450 2) kann unterschiedliche Formen (physikalisch oder mathematisch) annehmen und ist nicht Gegenstand dieses Dokuments.
ANMERKUNG   Die ausführlichen Regeln für Maximum  und Minimum Material Bedingungen für Bezüge sind in ISO 2692 angegeben.

Spécification géométrique des produits (GPS) - Tolérancement géométrique -— Références spécifiées et systèmes de références spécifiées (ISO/FDIS 5459:2024)

L'ISO 5459:2011 spécifie la terminologie, les règles et la méthodologie pour indiquer les références spécifiées et les systèmes de références spécifiées dans la documentation technique de produits. Elle fournit également des explications aidant l'utilisateur à la compréhension des concepts considérés.
L'ISO 5459:2011 définit l'opérateur de spécification utilisé pour établir une référence spécifiée ou un système de références spécifiées. L'opérateur de vérification qui peut prendre différentes formes (physique ou mathématique) ne fait pas l'objet de l'ISO 5459:2011.

Specifikacija geometrijskih veličin izdelka - Geometrijsko toleriranje - Reference in sistemi referenc (ISO/FDIS 5459:2024)

General Information

Status
Not Published
Public Enquiry End Date
24-Jun-2024
ICS
17.040.10 - Limits and fits
17.040.40 - Geometrical Product Specification (GPS)
Technical Committee
ISEL - Mechanical elements
Current Stage
4020 - Public enquire (PE) (Adopted Project)
Start Date
11-Apr-2024
Due Date
29-Aug-2024
Ref Project
prEN ISO 5459 - Geometrical product specifications (GPS) - Geometrical tolerancing - Datums and datum systems (ISO/DIS 5459:2024)

Relations

Revises
SIST EN ISO 5459:2011 - Geometrical product specifications (GPS) - Geometrical tolerancing - Datums and datum systems (ISO 5459:2011)
Effective Date
11-Oct-2023

Buy Standard

prEN ISO 5459:2024prEN ISO 5459:2024
PreviousNext
Draft
prEN ISO 5459:2024
English language
119 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN ISO 5459:2024
01-junij-2024
Specifikacija geometrijskih veličin izdelka - Geometrijsko toleriranje - Reference in
sistemi referenc (ISO/FDIS 5459:2024)
Geometrical product specifications (GPS) - Geometrical tolerancing - Datums and datum
systems (ISO/FDIS 5459:2024)
Geometrische Produktspezifikation (GPS) - Geometrische Tolerierung - Bezüge und
Bezugssysteme (ISO/FDIS 5459:2024)
Spécification géométrique des produits (GPS) - Tolérancement géométrique -
Références spécifiées et systèmes de références spécifiées (ISO/FDIS 5459:2024)
Ta slovenski standard je istoveten z: prEN ISO 5459
ICS:
17.040.10 Tolerance in ujemi Limits and fits
17.040.40 Specifikacija geometrijskih Geometrical Product
veličin izdelka (GPS) Specification (GPS)
oSIST prEN ISO 5459:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 5459:2024

---------------------- Page: 2 ----------------------
oSIST prEN ISO 5459:2024
FINAL DRAFT
International
Standard
ISO/FDIS 5459
ISO/TC 213
Geometrical product specifications
Secretariat: BSI
(GPS) — Geometrical tolerancing —
Voting begins on:
Datums and datum systems
2024-04-03
Spécification géométrique des produits (GPS) — Tolérancement
Voting terminates on:
géométrique — Références spécifiées et systèmes de références
2024-06-26
spécifiées
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO­
ISO/CEN PARALLEL PROCESSING LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
Reference number
ISO/FDIS 5459:2024(en) © ISO 2024

---------------------- Page: 3 ----------------------
oSIST prEN ISO 5459:2024
FINAL DRAFT
ISO/FDIS 5459:2024(en)
International
Standard
ISO/FDIS 5459
ISO/TC 213
Geometrical product specifications
Secretariat: BSI
(GPS) — Geometrical tolerancing —
Voting begins on:
Datums and datum systems
Spécification géométrique des produits (GPS) — Tolérancement
Voting terminates on:
géométrique — Références spécifiées et systèmes de références
spécifiées
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT,
COPYRIGHT PROTECTED DOCUMENT
WITH THEIR COMMENTS, NOTIFICATION OF ANY
RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE
AND TO PROVIDE SUPPOR TING DOCUMENTATION.
© ISO 2024
IN ADDITION TO THEIR EVALUATION AS
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO­
ISO/CEN PARALLEL PROCESSING
LOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL
or ISO’s member body in the country of the requester.
TO BECOME STAN DARDS TO WHICH REFERENCE MAY BE
MADE IN NATIONAL REGULATIONS.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/FDIS 5459:2024(en) © ISO 2024

© ISO 2024 – All rights reserved
ii

---------------------- Page: 4 ----------------------
oSIST prEN ISO 5459:2024
ISO/FDIS 5459:2024(en)
Contents Page
Foreword .v
Introduction .vii
1 Scope . 1
2 Normative references . 1
3 Terms and definitions .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN ISO 14405-2:2019(Main)
Geometrical product specifications (GPS) - Dimensional tolerancing - Part 2: Dimensions other than linear or angular sizes (ISO 14405-2:2018)
EN ISO 14405-2:2019

This document illustrates the ambiguity caused by the use of dimensional specifications to control
properties other than linear or angular size and the benefit of using geometrical specifications instead.
Dimensional tolerancing can be indicated by ± tolerancing or geometrical specifications.
The ambiguity caused by using ± tolerances for dimensions other than linear or angular sizes (for
individual tolerances and general tolerances according to, e.g. ISO 2768-1 and ISO 8062-3) is explained
in Annex A.
NOTE 1 The figures, as shown in this document, merely illustrate the text and are not intended to reflect
actual usage. The figures are consequently simplified to indicate only the relevant principles.
NOTE 2 For indications of dimensional specifications, see the following:
— ISO 14405-1 for linear size;
— ISO 14405-3 for angular size;
— ISO 2538-1 and ISO 2538-2 for wedges;
— ISO 3040 for cones.
NOTE 3 The rules for geometrical specifications are given in ISO 1101.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 5458:2018(Main)
Geometrical product specifications (GPS) - Geometrical tolerancing - Pattern and combined geometrical specification (ISO 5458:2018)
EN ISO 5458:2018

This document establishes complementary rules to ISO 1101 to be applied to pattern specifications and
defines rules to combine individual specifications, for geometrical specifications e.g. using the symbols
POSITION, SYMMETRY, LINE PROFILE and SURFACE PROFILE, as well as STRAIGHTNESS (in the case
where the toleranced features are nominally coaxial) and FLATNESS (in the case where the toleranced
features are nominally coplanar) as listed in Annex C.
These rules apply when a set of tolerance zones are grouped together with location or orientation
constraints, through the use of the CZ, CZR or SIM modifiers.
This document does not cover the use of the pattern specifications when the least and maximum
material requirement is applied (see ISO 2692).
This document does not cover the establishment of common datum (see ISO 5459) based on pattern
features.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 1101:2017(Main)
Geometrical product specifications (GPS) - Geometrical tolerancing - Tolerances of form, orientation, location and run-out (ISO 1101:2017)
EN ISO 1101:2017

SIST EN ISO 1101 defines the symbol language for geometrical specification of workpieces and the rules for its interpretation. It provides the foundation for geometrical specification. The illustrations in this document are intended to illustrate how a specification can be fully indicated with visible annotation (including e.g. TEDs).

  • Standard
    156 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    153 pages
    German language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    162 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 1660:2017(Main)
Geometrical product specifications (GPS) - Geometrical tolerancing - Profile tolerancing (ISO 1660:2017)
EN ISO 1660:2017

This document gives the rules for geometrical specifications of integral and derived features, using the
line profile and surface profile characteristic symbols as defined in ISO 1101.

  • Standard
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 14405-3:2017(Main)
Geometrical product specifications (GPS) - Dimensional tolerancing - Part 3: Angular sizes (ISO 14405-3:2016)
EN ISO 14405-3:2017

This part of ISO 14405 establishes the default specification operator for angular size and defines a number of special specification operators for features of size with angular size (e.g. wedges or cones).
This part of ISO 14405 also defines the specification modifiers and the drawing indications for these angular sizes.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    29 pages
    German language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 14405-1:2016(Main)
Geometrical product specifications (GPS) - Dimensional tolerancing - Part 1: Linear sizes (ISO 14405-1:2016)
EN ISO 14405-1:2016

This part of ISO 14405 establishes the default specification operator (see ISO 17450‑2) for linear size
and defines a number of special specification operators for linear size for features of size, e.g. “cylinder”,
“sphere”, “torus,”1), “circle”, “two parallel opposite planes”, or “two parallel opposite straight lines”.
It also defines the specification modifiers and the drawing indications for these linear sizes.
This part of ISO 14405 covers the following linear sizes:
a) local size:
— two-point size;
— spherical size;
— section size;
— portion size;
b) global size:
— direct global linear size:
— least-squares size;
— maximum inscribed size;
— minimum circumscribed size;
— minimax size;
— indirect global linear size;
c) calculated size:
— circumference diameter;
— area diameter;
— volume diameter;
1) A torus is a feature of size when its directrix diameter is fixed.
d) rank-order size:
— maximum size;
— minimum size;
— average size;
— median size;
— mid-range size;
— range of sizes;
— standard deviation of sizes.
This part of ISO 14405 defines tolerances of linear sizes for the following:
— a + and/or − limit deviation (e.g. 0/−0,019) (see Figure 11);
— an upper limit of size (ULS) and/or lower limit of size (LLS) (e.g. 15,2 max., 12 min., or 30,2/30,181)
(see Figure 13);
— an ISO tolerance class code in accordance with ISO 286‑1 (e.g. 10 h6) (see Figure 12);
with or without modifiers (see Tables 1 and 2).
This part of ISO 14405 provides a set of tools to express several types of size characteristic. It does not
present any information on the relationship between a function or a use and a size characteristic.

  • Standard
    64 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    64 pages
    German language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 3040:2016(Main)
Geometrical product specifications (GPS) - Dimensioning and tolerancing - Cones (ISO 3040:2016)
EN ISO 3040:2016

This International Standard specifies graphical indication applicable to a cone (right-angle circular
cones) to define its dimensioning or to specify its tolerancing.
For the purposes of this International Standard, the term “cone” relates to right-angle circular cones
only (any intersection by a plane perpendicular to the axis of the nominal cone is a circle).
NOTE 1 For simplicity, only truncated cones have been represented in this International Standard. However,
this International Standard can be applied to any type of cone within its scope.
NOTE 2 This International Standard is not intended to prevent the use of other methods of dimensioning and
tolerancing.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 286-1:2010/AC:2014(Corrigendum)
Geometrical product specifications (GPS) - ISO code system for tolerances on linear sizes - Part 1: Basis of tolerances, deviations and fits - Technical Corrigendum 1 (ISO 286-1:2010/Cor 1:2013)
EN ISO 286-1:2010/AC:2013

This part of ISO 286 establishes the ISO code system for tolerances to be used for linear sizes of features of the following types: a) cylinder; b) two parallel opposite surfaces. It defines the basic concepts and the related terminology for this code system. It provides a standardized selection of tolerance classes for general purposes from amongst the numerous possibilities. Additionally, it defines the basic terminology for fits between two features of size without constraints of orientation and location and explains the principles of “basic hole” and “basic shaft”.

  • Corrigendum
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 286-2:2010/AC:2014(Corrigendum)
Geometrical product specifications (GPS) - ISO code system for tolerances on linear sizes - Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts - Technical Corrigendum 1 (ISO 286-2:2010/Cor 1:2013)
EN ISO 286-2:2010/AC:2013

This part of ISO 286 gives values of the limit deviations for commonly used tolerance classes for holes and shafts calculated from the tables given in ISO 286-1. This part of ISO 286 covers values for the upper limit deviations ES (for holes) and es (for shafts), and the lower limit deviations EI (for holes) and ei (for shafts) (see Figures 1 and 2).

  • Corrigendum
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 5459:2011(Main)
Geometrical product specifications (GPS) - Geometrical tolerancing - Datums and datum systems (ISO 5459:2011)
EN ISO 5459:2011

This International Standard specifies terminology, rules and methodology for the indication and understanding of datums and datum systems in technical product documentation. This International Standard also provides explanations to assist the user in understanding the concepts involved. This International Standard defines the specification operator (see ISO 17450-2) used to establish a datum or datum system. The verification operator (see ISO 17450-2) can take different forms (physically or mathematically) and is not the subject of this International Standard.

  • Standard
    89 pages
    English language
    sale 10% off
    e-Library read for
    1 day