iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN ISO 286-1:2010/AC:2014

(Corrigendum)

Geometrical product specifications (GPS) - ISO code system for tolerances on linear sizes - Part 1: Basis of tolerances, deviations and fits - Technical Corrigendum 1 (ISO 286-1:2010/Cor 1:2013)

Geometrical product specifications (GPS) - ISO code system for tolerances on linear sizes - Part 1: Basis of tolerances, deviations and fits - Technical Corrigendum 1 (ISO 286-1:2010/Cor 1:2013)

This part of ISO 286 establishes the ISO code system for tolerances to be used for linear sizes of features of the following types: a) cylinder; b) two parallel opposite surfaces. It defines the basic concepts and the related terminology for this code system. It provides a standardized selection of tolerance classes for general purposes from amongst the numerous possibilities. Additionally, it defines the basic terminology for fits between two features of size without constraints of orientation and location and explains the principles of “basic hole” and “basic shaft”.

Geometrische Produktspezifikation (GPS) - ISO-Toleranzsystem für Längenmaße - Teil 1: Grundlagen für Toleranzen, Abmaße und Passungen (ISO 286-1:2010/Cor 1:2013)

Spécification géométrique des produits (GPS) - Système de codification ISO pour les tolérances sur les tailles linéaires - Partie 1: Base des tolérances, écarts et ajustements - Rectificatif technique 1 (ISO 286-1:2010/Cor 1:2013)

Specifikacija geometrijskih veličin izdelka - Tolerančni sistem ISO za dolžinske mere - 1. del: Osnova za tolerance, odstopanja in ujeme (ISO 286-1:2010/Cor 1:2013)

Ta del ISO 286 vzpostavlja tolerančni sistem ISO za uporabo za dolžinske mere oblik naslednjih vrst: a) valj; b) dve vzporedni nasprotni površini. Določa osnovne koncepte in povezano terminologijo za ta kodni sistem. Zagotavlja standardiziran izbor tolerančnih razredov za splošne namene izmed vseh številnih možnosti. Poleg tega definira osnovno terminologijo za ujeme med dvema oblikama velikosti, brez omejitev glede usmerjenosti in lokacije, ter pojasnjuje načela »osnovne odprtine« in »osnovne palice«.

General Information

Status
Published
Publication Date
15-May-2014
ICS
17.040.10 - Limits and fits
17.040.40 - Geometrical Product Specification (GPS)
Technical Committee
ISEL - Mechanical elements
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
13-May-2014
Due Date
18-Jul-2014
Completion Date
16-May-2014
Ref Project
EN ISO 286-1:2010/AC:2013 - Geometrical product specifications (GPS) - ISO code system for tolerances on linear sizes - Part 1: Basis of tolerances, deviations and fits - Technical Corrigendum 1 (ISO 286-1:2010/Cor 1:2013)

Relations

Corrects
SIST EN ISO 286-1:2010 - Geometrical product specifications (GPS) - ISO code system for tolerances on linear sizes - Part 1: Basis of tolerances, deviations and fits (ISO 286-1:2010)
Effective Date
01-Jul-2014

Buy Standard

EN ISO 286-1:2010/AC:2014EN ISO 286-1:2010/AC:2014
PreviousNext
Corrigendum
EN ISO 286-1:2010/AC:2014
English language
7 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.&RUGeometrische Produktspezifikation (GPS) - ISO-Toleranzsystem für Längenmaße - Teil 1: Grundlagen für Toleranzen, Abmaße und Passungen
(ISO 286-1:2010/Cor 1:2013)Spécification géométrique des produits (GPS) - Système de codification ISO pour les tolérances sur les tailles linéaires - Partie 1: Base des tolérances, écarts et ajustements - Rectificatif technique 1 (ISO 286-1:2010/Cor 1:2013)Geometrical product specifications (GPS) - ISO code system for tolerances on linear sizes - Part 1: Basis of tolerances, deviations and fits - Technical Corrigendum 1 (ISO 286-1:2010/Cor 1:2013)17.040.40Geometrical Product Specification (GPS)17.040.10Tolerance in ujemiLimits and fitsICS:Ta slovenski standard je istoveten z:EN ISO 286-1:2010/AC:2013SIST EN ISO 286-1:2010/AC:2014en01-julij-2014SIST EN ISO 286-1:2010/AC:2014SLOVENSKI
STANDARD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN ISO 286-1:2010/AC
August 2013
Août 2013
August 2013 ICS 17.040.10 English version Version Française Deutsche Fassung
Geometrical product specifications (GPS) - ISO code system for tolerances on linear sizes - Part 1: Basis of tolerances, deviations and fits - Technical Corrigendum 1 (ISO 286-1:2010/Cor 1:2013)
Spécification géométrique des produits (GPS) - Système de codification ISO pour les tolérances sur les tailles linéaires - Partie 1: Base des tolérances, écarts et ajustements - Rectificatif technique 1 (ISO 286-1:2010/Cor 1:2013)
Geometrische Produktspezifikation (GPS) -ISO-Toleranzsystem für Längenmaße - Teil 1: Grundlagen für Toleranzen, Abmaße und Passungen
(ISO 286-1:2010/Cor 1:2013)This corrigendum becomes effective on 7 August 2013 for incorporation in the three official language versions of the EN.
Ce corrigendum prendra effet le 7 août 2013 pour incorporation dans les trois versions linguistiques officielles de la EN.
Die Berichtigung tritt am 7. August 2013 zur Einarbeitung in die drei offiziellen Sprachfassungen der EN in Kraft.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Tous droits d'exploitation sous quelque forme et de quelque manière que ce soit réservés dans le monde entier aux membres nationaux du CEN. Alle Rechte der Verwertung, gleich in welcher Form und in welchem Verfahren, sind weltweit den nationalen Mitgliedern von CEN vorbehalten. Ref. No.:EN ISO 286-1:2010/AC:2013 D/E/FSIST EN ISO 286-1:2010/AC:2014

Page Foreword .3
INTERNATIONAL STANDARD ISO 286-1:2010 TECHNICAL CORRIGENDUM 1 Published 2013-08-01 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION 
 ORGANISATION INTERNATIONALE DE NORMALISATION
Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes
— Part 1: Basis of tolerances, deviations and fits TECHNICAL CORRIGENDUM 1 Spécification géométrique des produits (GPS) — Système de codification ISO pour les tolérances sur les tailles linéaires — Partie 1: Base des tolér
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN ISO 5459:2024(Main)
Geometrical product specifications (GPS) - Geometrical tolerancing - Datums and datum systems (ISO 5459:2024)
EN ISO 5459:2024

ISO 5459:2011 specifies terminology, rules and methodology for the indication and understanding of datums and datum systems in technical product documentation. It also provides explanations to assist the user in understanding the concepts involved.
ISO 5459:2011 defines the specification operator (see ISO 17450-2) used to establish a datum or datum system. The verification operator (see ISO 17450-2) can take different forms (physically or mathematically) and is not the subject of ISO 5459:2011.
The detailed rules for maximum and least material requirements for datums are given in ISO 2692.

  • Standard
    125 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 14405-2:2019(Main)
Geometrical product specifications (GPS) - Dimensional tolerancing - Part 2: Dimensions other than linear or angular sizes (ISO 14405-2:2018)
EN ISO 14405-2:2019

This document illustrates the ambiguity caused by the use of dimensional specifications to control
properties other than linear or angular size and the benefit of using geometrical specifications instead.
Dimensional tolerancing can be indicated by ± tolerancing or geometrical specifications.
The ambiguity caused by using ± tolerances for dimensions other than linear or angular sizes (for
individual tolerances and general tolerances according to, e.g. ISO 2768-1 and ISO 8062-3) is explained
in Annex A.
NOTE 1 The figures, as shown in this document, merely illustrate the text and are not intended to reflect
actual usage. The figures are consequently simplified to indicate only the relevant principles.
NOTE 2 For indications of dimensional specifications, see the following:
— ISO 14405-1 for linear size;
— ISO 14405-3 for angular size;
— ISO 2538-1 and ISO 2538-2 for wedges;
— ISO 3040 for cones.
NOTE 3 The rules for geometrical specifications are given in ISO 1101.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 5458:2018(Main)
Geometrical product specifications (GPS) - Geometrical tolerancing - Pattern and combined geometrical specification (ISO 5458:2018)
EN ISO 5458:2018

This document establishes complementary rules to ISO 1101 to be applied to pattern specifications and
defines rules to combine individual specifications, for geometrical specifications e.g. using the symbols
POSITION, SYMMETRY, LINE PROFILE and SURFACE PROFILE, as well as STRAIGHTNESS (in the case
where the toleranced features are nominally coaxial) and FLATNESS (in the case where the toleranced
features are nominally coplanar) as listed in Annex C.
These rules apply when a set of tolerance zones are grouped together with location or orientation
constraints, through the use of the CZ, CZR or SIM modifiers.
This document does not cover the use of the pattern specifications when the least and maximum
material requirement is applied (see ISO 2692).
This document does not cover the establishment of common datum (see ISO 5459) based on pattern
features.

  • Standard
    52 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 1101:2017(Main)
Geometrical product specifications (GPS) - Geometrical tolerancing - Tolerances of form, orientation, location and run-out (ISO 1101:2017)
EN ISO 1101:2017

SIST EN ISO 1101 defines the symbol language for geometrical specification of workpieces and the rules for its interpretation. It provides the foundation for geometrical specification. The illustrations in this document are intended to illustrate how a specification can be fully indicated with visible annotation (including e.g. TEDs).

  • Standard
    156 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    153 pages
    German language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 1660:2017(Main)
Geometrical product specifications (GPS) - Geometrical tolerancing - Profile tolerancing (ISO 1660:2017)
EN ISO 1660:2017

This document gives the rules for geometrical specifications of integral and derived features, using the
line profile and surface profile characteristic symbols as defined in ISO 1101.

  • Standard
    55 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 14405-3:2017(Main)
Geometrical product specifications (GPS) - Dimensional tolerancing - Part 3: Angular sizes (ISO 14405-3:2016)
EN ISO 14405-3:2017

This part of ISO 14405 establishes the default specification operator for angular size and defines a number of special specification operators for features of size with angular size (e.g. wedges or cones).
This part of ISO 14405 also defines the specification modifiers and the drawing indications for these angular sizes.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    29 pages
    German language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 14405-1:2016(Main)
Geometrical product specifications (GPS) - Dimensional tolerancing - Part 1: Linear sizes (ISO 14405-1:2016)
EN ISO 14405-1:2016

This part of ISO 14405 establishes the default specification operator (see ISO 17450‑2) for linear size
and defines a number of special specification operators for linear size for features of size, e.g. “cylinder”,
“sphere”, “torus,”1), “circle”, “two parallel opposite planes”, or “two parallel opposite straight lines”.
It also defines the specification modifiers and the drawing indications for these linear sizes.
This part of ISO 14405 covers the following linear sizes:
a) local size:
— two-point size;
— spherical size;
— section size;
— portion size;
b) global size:
— direct global linear size:
— least-squares size;
— maximum inscribed size;
— minimum circumscribed size;
— minimax size;
— indirect global linear size;
c) calculated size:
— circumference diameter;
— area diameter;
— volume diameter;
1) A torus is a feature of size when its directrix diameter is fixed.
d) rank-order size:
— maximum size;
— minimum size;
— average size;
— median size;
— mid-range size;
— range of sizes;
— standard deviation of sizes.
This part of ISO 14405 defines tolerances of linear sizes for the following:
— a + and/or − limit deviation (e.g. 0/−0,019) (see Figure 11);
— an upper limit of size (ULS) and/or lower limit of size (LLS) (e.g. 15,2 max., 12 min., or 30,2/30,181)
(see Figure 13);
— an ISO tolerance class code in accordance with ISO 286‑1 (e.g. 10 h6) (see Figure 12);
with or without modifiers (see Tables 1 and 2).
This part of ISO 14405 provides a set of tools to express several types of size characteristic. It does not
present any information on the relationship between a function or a use and a size characteristic.

  • Standard
    64 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    64 pages
    German language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 3040:2016(Main)
Geometrical product specifications (GPS) - Dimensioning and tolerancing - Cones (ISO 3040:2016)
EN ISO 3040:2016

This International Standard specifies graphical indication applicable to a cone (right-angle circular
cones) to define its dimensioning or to specify its tolerancing.
For the purposes of this International Standard, the term “cone” relates to right-angle circular cones
only (any intersection by a plane perpendicular to the axis of the nominal cone is a circle).
NOTE 1 For simplicity, only truncated cones have been represented in this International Standard. However,
this International Standard can be applied to any type of cone within its scope.
NOTE 2 This International Standard is not intended to prevent the use of other methods of dimensioning and
tolerancing.

  • Standard
    32 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 286-2:2010/AC:2014(Corrigendum)
Geometrical product specifications (GPS) - ISO code system for tolerances on linear sizes - Part 2: Tables of standard tolerance classes and limit deviations for holes and shafts - Technical Corrigendum 1 (ISO 286-2:2010/Cor 1:2013)
EN ISO 286-2:2010/AC:2013

This part of ISO 286 gives values of the limit deviations for commonly used tolerance classes for holes and shafts calculated from the tables given in ISO 286-1. This part of ISO 286 covers values for the upper limit deviations ES (for holes) and es (for shafts), and the lower limit deviations EI (for holes) and ei (for shafts) (see Figures 1 and 2).

  • Corrigendum
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 286-1:2010(Main)
Geometrical product specifications (GPS) - ISO code system for tolerances on linear sizes - Part 1: Basis of tolerances, deviations and fits (ISO 286-1:2010)
EN ISO 286-1:2010

This part of ISO 286 establishes the ISO code system for tolerances to be used for linear sizes of features of the following types: a) cylinder; b) two parallel opposite surfaces. It defines the basic concepts and the related terminology for this code system. It provides a standardized selection of tolerance classes for general purposes from amongst the numerous possibilities. Additionally, it defines the basic terminology for fits between two features of size without constraints of orientation and location and explains the principles of “basic hole” and “basic shaft”.

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day