SIST EN ISO 19069-2:2016
(Main)Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 19069-2:2016)
Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 19069-2:2016)
This part of ISO 19069 specifies the methods of preparation of test specimens and the test methods
to be used in determining the properties of polypropylene (PP) moulding and extrusion materials.
Requirements for handling test material and for conditioning both the test material before moulding
and the specimens before testing are given.
Procedures and conditions for the preparation of test specimens and procedures for measuring properties
of the materials from which these specimens are made are also given. Properties and test methods which
are suitable and necessary to characterize PP moulding and extrusion materials are listed.
The properties have been selected from the general test methods in ISO 10350-1. Other test methods in
wide use for, or of particular significance to, these moulding and extrusion materials are also included
in this part of ISO 19069, as are the designatory properties specified in ISO 19069-1.
In order to obtain reproducible and comparable test results, it is necessary to use the methods of
preparation and conditioning, the specimen dimensions and the test procedures specified herein.
Values determined will not necessarily be identical to those obtained using specimens of different
dimensions or prepared using different procedures.
Kunststoffe - Polypropylen (PP)-Formmassen - Teil 2: Herstellung von Probekörpern und Bestimmung von Eigenschaften (ISO 19069-2:2016)
Dieser Teil von ISO 19069 legt die Verfahren zur Herstellung von Probekörpern und die Prüfverfahren zur Bestimmung der Eigenschaften von Polypropylen (PP)-Formmassen fest. Anforderungen an die Behandlung des Probematerials und an das Konditionieren des Probematerials sowohl vor dem Formen der Probekörper als auch der Probekörper vor der Prüfung sind enthalten.
Verfahren und Bedingungen für die Herstellung der Probekörper und Verfahren für die Bestimmung der Eigenschaften der Formmasse, aus denen die Probekörper hergestellt werden, sind auch angegeben. Eigenschaften und Prüfverfahren, die anwendbar und notwendig sind, um Polypropylen (PP)-Formmassen zu charakterisieren, sind aufgelistet.
Die Eigenschaften wurden aus den allgemeinen Prüfverfahren in ISO 10350-1 entnommen. Andere weithin gebräuchliche Prüfverfahren oder solche von besonderer Bedeutung für diese Formmassen sind ebenfalls in diesem Teil von ISO 19069 aufgenommen, wie auch die kennzeichnenden Eigenschaften aus ISO 19069-1.
Um reproduzierbare und vergleichbare Prüfergebnisse zu erhalten, ist es notwendig, die Probekörper-herstellung und -konditionierung, die Probekörperabmessungen sowie die Prüfverfahren wie hier festgelegt anzuwenden. Die gemessenen Werte werden nicht notwendigerweise mit denen identisch sein, die bei Anwendung von Probekörpern anderer Abmessungen oder solchen, die mit einem anderen Verfahren hergestellt wurden, erhalten wurden.
Plastiques - Polypropylène (PP) pour moulage et extrusion - Partie 2: Préparation des éprouvettes et détermination des propriétés (ISO 19069-2:2016)
ISO 19069-2:2016 spécifie les méthodes de préparation des éprouvettes et les méthodes d'essai à appliquer pour déterminer les propriétés des polypropylènes (PP) pour moulage et extrusion. Elle indique les exigences requises lors de la manipulation du matériau pour essai, ainsi que lors de conditionnement dudit matériau avant moulage et des éprouvettes avant l'essai.
Elle précise les modes opératoires et les conditions nécessaires à la préparation des éprouvettes, ainsi que les modes opératoires de mesurage des propriétés des matériaux à partir desquels ces éprouvettes sont fabriquées. Elle fournit également une liste des propriétés et des méthodes d'essai appropriées et nécessaires à la caractérisation des polypropylènes pour moulage et extrusion.
Les propriétés ont été choisies parmi les méthodes d'essai générales données dans l'ISO 10350‑1. D'autres méthodes d'essai, présentant une importance particulière ou largement utilisées dans le cas de ces matériaux pour moulage et extrusion, sont également incluses dans la présente partie de l'ISO 19069, comme le sont les propriétés de désignation figurant dans l'ISO 19069‑1.
Pour obtenir des résultats d'essai reproductibles et comparables, il est nécessaire d'utiliser les méthodes de préparation et de conditionnement, ainsi que les dimensions d'éprouvettes et les modes opératoires d'essai prescrits ci-après. Les valeurs ainsi déterminées ne seront pas nécessairement identiques à celles obtenues en utilisant des éprouvettes de dimensions différentes ou préparées selon des modes opératoires différents.
Polimerni materiali - Polipropilenski (PP) materiali za oblikovanje in ekstrudiranje - 2. del: Priprava preskušancev in ugotavljanje lastnosti (ISO 19069-2:2016)
Ta del standarda ISO 19069 določa metode za pripravo preskušancev in preskusnih metod, ki se uporabljajo za ugotavljanje lastnosti polipropilenskih (PP) materialov za oblikovanje in ekstrudiranje.
Podane so zahteve za ravnanje s preskusnim materialom ter za obdelavo preskusnega materiala pred oblikovanjem in obdelavo preskušancev pred preskusom.
Podani so tudi postopki in pogoji za pripravo preskušancev ter postopki za merjenje lastnosti materialov, iz katerih so preskušanci izdelani. Navedene so lastnosti in preskusne metode, ki so primerne in nujne za opredelitev polipropilenskih materialov za oblikovanje in ekstrudiranje.
Lastnosti so bile izbrane na podlagi splošnih preskusnih metod iz standarda ISO 10350-1. Druge preskusne metode, ki so v splošni uporabi ali so posebej pomembne za te materiale za oblikovanje in ekstrudiranje, so prav tako vključene v ta del standarda ISO 19069. Vključene so tudi označevalne lastnosti, ki so določene v standardu ISO 19069-1.
Da se zagotovijo primerljivi in ponovljivi rezultati preskusa, je treba uporabljati metode priprave in obdelave, mere preskušanca ter preskusne postopke, ki so navedeni v tem delu. Pri tem ni nujno, da bodo ugotovljene vrednosti enake tistim, ki so pridobljene z uporabo preskušancev, ki imajo drugačne mere ali so pripravljeni z uporabo drugih postopkov.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 19069-2:2016
01-maj-2016
1DGRPHãþD
SIST EN ISO 1873-2:2007
Polimerni materiali - Polipropilenski (PP) materiali za oblikovanje in ekstrudiranje -
2. del: Priprava preskušancev in ugotavljanje lastnosti (ISO 19069-2:2016)
Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of
test specimens and determination of properties (ISO 19069-2:2016)
Kunststoffe - Polypropylen (PP)-Formmassen - Teil 2: Herstellung von Probekörpern und
Bestimmung von Eigenschaften (ISO 19069-2:2016)
Plastiques - Polypropylène (PP) pour moulage et extrusion - Partie 2: Préparation des
éprouvettes et détermination des propriétés (ISO 19069-2:2016)
Ta slovenski standard je istoveten z: EN ISO 19069-2:2016
ICS:
83.080.20 Plastomeri Thermoplastic materials
SIST EN ISO 19069-2:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 19069-2:2016
---------------------- Page: 2 ----------------------
SIST EN ISO 19069-2:2016
EN ISO 19069-2
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2016
EUROPÄISCHE NORM
ICS 83.080.20 Supersedes EN ISO 1873-2:2007
English Version
Plastics - Polypropylene (PP) moulding and extrusion
materials - Part 2: Preparation of test specimens and
determination of properties (ISO 19069-2:2016)
Plastiques - Polypropylène (PP) pour moulage et Kunststoffe - Polypropylen (PP)-Werkstoffe - Teil 2:
extrusion - Partie 2: Préparation des éprouvettes et Herstellung von Probekörpern und Bestimmung von
détermination des propriétés (ISO 19069-2:2016) Eigenschaften (ISO 19069-2:2016)
This European Standard was approved by CEN on 23 January 2016.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19069-2:2016 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 19069-2:2016
EN ISO 19069-2:2016 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 19069-2:2016
EN ISO 19069-2:2016 (E)
European foreword
This document (EN ISO 19069-2:2016) has been prepared by Technical Committee ISO/TC 61 "Plastics"
in collaboration with Technical Committee CEN/TC 249 “Plastics” the secretariat of which is held by
NBN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2016, and conflicting national standards
shall be withdrawn at the latest by September 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 1873-2:2007.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 19069-2:2016 has been approved by CEN as EN ISO 19069-2:2016 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 19069-2:2016
---------------------- Page: 6 ----------------------
SIST EN ISO 19069-2:2016
INTERNATIONAL ISO
STANDARD 19069-2
First edition
2016-02-15
Plastics — Polypropylene (PP)
moulding and extrusion materials —
Part 2:
Preparation of test specimens and
determination of properties
Plastiques — Polypropylène (PP) pour moulage et extrusion —
Partie 2: Préparation des éprouvettes et détermination des propriétés
Reference number
ISO 19069-2:2016(E)
©
ISO 2016
---------------------- Page: 7 ----------------------
SIST EN ISO 19069-2:2016
ISO 19069-2:2016(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 19069-2:2016
ISO 19069-2:2016(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Preparation of test specimens . 3
3.1 General . 3
3.2 Treatment of the material before moulding . 3
3.3 Injection moulding . 3
3.4 Compression moulding . 3
4 Conditioning of test specimens . 4
5 Determination of properties . 4
Bibliography . 8
© ISO 2016 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 19069-2:2016
ISO 19069-2:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT), see the following URL: Foreword — Supplementary information.
The committee responsible for this document is ISO/TC 61, Plastics, Subcommittee SC 9,
Thermoplastic materials.
This first edition of ISO 19069-2 cancels and replaces the third edition of ISO 1873-2:2007, which has
been technically revised.
ISO 19069 consists of the following parts, under the general title Plastics — Polypropylene (PP) moulding
and extrusion materials:
— Part 1: Designation system and basis for specifications
— Part 2: Preparation of test specimens and determination of properties
iv © ISO 2016 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 19069-2:2016
INTERNATIONAL STANDARD ISO 19069-2:2016(E)
Plastics — Polypropylene (PP) moulding and extrusion
materials —
Part 2:
Preparation of test specimens and determination of
properties
1 Scope
This part of ISO 19069 specifies the methods of preparation of test specimens and the test methods
to be used in determining the properties of polypropylene (PP) moulding and extrusion materials.
Requirements for handling test material and for conditioning both the test material before moulding
and the specimens before testing are given.
Procedures and conditions for the preparation of test specimens and procedures for measuring properties
of the materials from which these specimens are made are also given. Properties and test methods which
are suitable and necessary to characterize PP moulding and extrusion materials are listed.
The properties have been selected from the general test methods in ISO 10350-1. Other test methods in
wide use for, or of particular significance to, these moulding and extrusion materials are also included
in this part of ISO 19069, as are the designatory properties specified in ISO 19069-1.
In order to obtain reproducible and comparable test results, it is necessary to use the methods of
preparation and conditioning, the specimen dimensions and the test procedures specified herein.
Values determined will not necessarily be identical to those obtained using specimens of different
dimensions or prepared using different procedures.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
ISO 62, Plastics — Determination of water absorption
ISO 75-2, Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 178, Plastics — Determination of flexural properties
ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test
ISO 179-2, Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact tes
ISO 293, Plastics — Compression moulding of test specimens of thermoplastic materials
ISO 294-1, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General
principles, and moulding of multipurpose and bar test specimens
ISO 294-3, Plastics — Injection moulding of test specimens of t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.