SIST EN 1360:2013
(Main)Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification
Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification
This European Standard specifies minimum requirements for three types of hoses in two categories and two classes of hose assemblies used for measured fuel dispensing, including oxygenated fuels (up to a maximum of 15 % oxygenated compounds). The assemblies are intended for use at ambient temperatures between -30 °C and +55 °C for normal temperature class and -40 °C and +55 °C for low temperature class at a working pressure ≤ 16 bar. As part of the certification of a new dispenser, testing of fuel samples in accordance with EN 228 and EN 590 should be carried out at least eight weeks after the first use of the equipment to avoid unrepresentative sulphur content results.
Zapfstellenschläuche und -schlauchleitungen aus Gummi und Kunststoff - Anforderungen
Diese Europäische Norm legt die Mindestanforderungen für drei Typen von Zapfstellenschläuchen für Kraft-stoffe fest, die in zwei Kategorien und zwei Klassen unterteilt werden, wobei mit sauerstoffhaltigen Verbin-dungen angereicherte Kraftstoffe (bis zu einem maximalen Anteil von 15 % sauerstoffhaltigen Verbindungen) einbezogen sind. Die Anwendung von Schlauchleitungen der Normaltemperaturklasse ist bei Umgebungstemperaturen von −30 °C bis +55 °C und von Schlauchleitungen der Tieftemperaturklasse zwischen −40 °C und +55 °C bei einem Arbeitsdruck von ≤ 16 bar1) vorgesehen. ANMERKUNG Als Teil der Zertifizierung einer neuen Zapfsäule sollten Kraftstoffproben nach EN 228 und EN 590 mindestens 8 Wochen nach der ersten Verwendung der Ausrüstung geprüft werden, um unrepräsentative Ergebnisse in Zusammenhang mit dem Schwefelgehalt zu vermeiden.
Tuyaux et flexibles en caoutchouc pour distribution mesurée de carburant - Spécifications
La présente Norme européenne spécifie les exigences minimales pour trois types de tuyaux dans deux
catégories et deux classes d’assemblages flexibles utilisés pour la distribution mesurée des carburants, y
compris les carburants oxygénés (comprenant jusqu’à 15 % maximum de composés oxygénés).
Les assemblages sont destinés à être utilisés à des températures ambiantes comprises entre 30 °C et
55 °C pour une classe de température normale et entre 40 °C et 55 °C pour la classe basse température
à une pression de service 16 bar1).
NOTE Il convient qu’un essai de nouveau distributeur d’échantillons de carburant selon l’EN 228 et l’EN 590 soit
réalisé au moins 8 semaines après la première utilisation de l'équipement afin d'éviter des résultats en teneur en soufre
peu représentatifs, en tant qu’élément de la certification.
Gumene in polimerne cevi ter cevni priključki za sisteme za merjeno točenje goriv - Specifikacija
Ta evropski standard določa minimalne zahteve za tri vrste cevi v dveh kategorijah in dva razreda cevnih priključkov za sisteme za merjeno točenje goriva, vključno z oksigeniranimi gorivi (do največ 15 % kisikovih spojin). Priključki so namenjeni uporabi pri temperaturi okolice med -30 °C in +55 °C za običajni temperaturni razred ter -40 °C in +55 °C za nizki temperaturni razred pri delovnem tlaku ≤ 16 barov. Kot del postopka certificiranja nove naprave za točenje goriva je treba v skladu z EN 228 in EN 590 vsaj osem mesecev po prvi uporabi opreme preskusiti vzorce goriva, da se prepreči nereprezentativne rezultate vsebnosti žvepla.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Zapfstellenschläuche und -schlauchleitungen aus Gummi und Kunststoff - AnforderungenTuyaux et flexibles en caoutchouc pour distribution mesurée de carburant - SpécificationsRubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification83.140.40Gumene ceviHoses75.200Petroleum products and natural gas handling equipmentICS:Ta slovenski standard je istoveten z:EN 1360:2013SIST EN 1360:2013en,fr,de01-september-2013SIST EN 1360:2013SLOVENSKI
STANDARDSIST EN 1360:20051DGRPHãþD
SIST EN 1360:2013
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1360
June 2013 ICS 23.040.70; 75.200 Supersedes EN 1360:2005English Version
Rubber and plastic hoses and hose assemblies for measured fuel dispensing systems - Specification
Tuyaux et flexibles en caoutchouc et en plastique pour distribution mesurée de carburant - Spécifications
Zapfstellenschläuche und -schlauchleitungen aus Gummi und Kunststoff - Anforderungen This European Standard was approved by CEN on 25 April 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1360:2013: ESIST EN 1360:2013
EN 1360:2013 (E) 2 Contents Page Foreword .4 1 Scope .5 2 Normative references .5 3 Terms and definitions .5 4 Classification .6 5 Materials and construction .6 6 Pressure requirements .6 7 Dimensions and tolerances .6 7.1 Internal diameters and bend radii .6 7.2 Minimum thickness of lining and cover .7 7.3 Concentricity .7 7.4 Tolerance on cut lengths .7 8 Physical properties .7 8.1 Compounds .7 8.2 Finished hose .9 8.3 Hose assembly . 10 9 End fittings . 10 10 Type tests . 11 11 Frequency of testing . 11 12 Marking . 11 12.1 Hoses . 11 12.2 End fittings . 11 12.3 Hose assemblies . 12 Annex A (normative)
Test method for determination of low temperature resistance at –30 °C (for normal temperature class) and –40 °C (for low temperature class) . 13 A.1 Test piece . 13 A.2 Apparatus . 13 A.3 Test method . 13 Annex B (normative)
Method for the determination of adhesion between components . 14 B.1 Dry adhesion . 14 B.2 Adhesion after contact with fuel . 14 Annex C (normative)
Test method for the determination of low temperature flexibility . 15 C.1 Test piece . 15 C.2 Apparatus . 15 C.3 Test method . 15 Annex D (normative)
Test method for the determination of fuel permeation . 17 D.1 Test piece . 17 D.2 Apparatus . 17 D.3 Test method . 17 Annex E (normative)
Test method for flammability . 18 E.1 Test pieces . 18 E.2 Apparatus . 18 E.3 Test method . 18 Annex F (normative)
End-fitting pull-off test . 20 SIST EN 1360:2013
EN 1360:2013 (E) 3 F.1 Test piece . 20 F.2 Apparatus . 20 F.3 Test method . 20 Annex G (normative)
Test method for the determination of leakage (leak test) . 21 Annex H (normative)
Test method for fatigue strength under reversed bending stress (flex test) . 22 H.1 Apparatus and test pieces . 22 H.2 Test method . 22 H.3 Test observations and report . 23 Annex I (normative)
Test frequency for type tests and routine tests . 24 Annex J (informative)
Test frequency for production acceptance tests . 26 Bibliography . 28
SIST EN 1360:2013
EN 1360:2013 (E) 4 Foreword This document (EN 1360:2013) has been prepared by Technical Committee CEN/TC 218 “Rubber and plastics hoses and hose assemblies”, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2013, and conflicting national standards shall be withdrawn at the latest by December 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1360:2005. Compared with EN 1360:2005, the following fundamental changes were made: a) In Table 1 hoses with nominal bores of 35 and 50 have been included; b) The normative references have been updated. WARNING – Persons using this European Standard should be familiar with normal laboratory practice. This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure compliance with any national regulatory conditions. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
SIST EN 1360:2013
EN 1360:2013 (E) 5 1 Scope This European Standard specifies minimum requirements and test methods for verification for three types of hoses in two grades and two classes of hose assemblies used for measured fuel dispensing, including oxygenated fuels (up to a maximum of 15 % oxygenated compounds). The assemblies are intended for use at ambient temperatures between –30 °C and +55 °C for normal temperature class and –40 °C and +55 °C for low temperature class at a working pressure ≤ 16 bar1). As part of the certification of a new dispenser, testing of fuel samples in accordance with EN 228 and EN 590 should be carried out at least eight weeks after the first use of the equipment to avoid unrepresentative sulphur content results. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 26801, Rubber or plastics hoses — Determination of volumetric expansion (ISO 6801) EN ISO 1307, Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters and tolerances on cut-to-length hoses (ISO 1307) EN ISO 1402, Rubber and plastics hoses and hose assemblies — Hydrostatic testing (ISO 1402) EN ISO 4671, Rubber and plastics hoses and hose assemblies — Methods of measurement of the dimensions of hoses and the lengths of hose assemblies (ISO 4671) EN ISO 7326, Rubber and plastics hoses — Assessment of ozone resistance under static conditions (ISO 7326) EN ISO 8031:2009, Rubber and plastics hoses and hose assemblies — Determination of electrical resistance and conductivity (ISO 8031:2009) EN ISO 8033, Rubber and plastics hose — Determination of adhesion between components (ISO 8033) EN ISO 8330:2008, Rubber and plastics hoses and hose assemblies — Vocabulary (ISO 8330:2007) EN ISO 10619-1, Rubber or plastics hoses and tubing — Measurement of flexibility and stiffness — Part 1: Bending tests at ambient temperature (ISO 10619-1) ISO 37, Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties ISO 188, Rubber, vulcanized or thermoplastic — Accelerated ageing and heat-resistance tests ISO 554, Standard atmospheres for conditioning and/or testing — Specifications ISO 1817, Rubber, vulcanized or thermoplastic — Determination of the effect of liquids ISO 4649:2010, Rubber, vulcanized or thermoplastic — Determination of abrasion resistance using a rotating cylindrical drum device 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 8330:2008 apply.
1) 1 bar = 0,1 MPa SIST EN 1360:2013
EN 1360:2013 (E) 6 4 Classification Hoses for this application shall be divided into three types: Type 1: textile reinforced; Type 2: textile and helical wire reinforced;
Type 3: fine wire reinforced. Each type of hose shall be divided into two grades: Grade M: electrically bonded; Grade Ω: electrically conductive. Each type of hose shall be divided into two temperature classes: Normal temperature class with an ambient working temperature of −30 °C to +55 °C; Low temperature class (LT) with an ambient working temperature of −40 °C to +55 °C. 5 Materials and construction The hose shall consist of the following: a) a smooth, fuel resistant lining of rubber or thermoplastic elastomer (TPE); b) a reinforcement; related to type; c) a non-corrugated, fuel and weather-resistant rubber or TPE cover. Hose assemblies shall be capable of conducting an electrical charge from coupling to coupling. When this capability is provided by means of metallic bonding wires, not less than two (metallic) bonding wires shall be embedded in the hose and the metal used shall have a high resistance to fatigue and corrosion. Hoses with metallic wires for electrical conductivity shall be designated 'M' and those using conductive compounds shall be designated 'Ω', the relevant mark being branded on the hose (see Clause 12). 6 Pressure requirements For all types of hoses the following shall apply: a) maximum working pressure: 16 bar; b) proof pressure: 24 bar; c) minimum bursting pressure: 48 bar. 7 Dimensions and tolerances 7.1 Internal diameters and bend radii When measured in accordance with EN ISO 4671, the internal diameter of the hose shall comply with the values given in Table 1. SIST EN 1360:2013
EN 1360:2013 (E) 7 When measured in accordance with EN ISO 10619-1, the minimum bend radii for each diameter of hose shall be in accordance with Table 1. Table 1 — Nominal bore, internal diameter, tolerance and bend radii Nominal bore Internal diameter mm Tolerance mm Bend radius mm 12 16 19 12,5 16,0 19,0 ± 0,8 60 80 100 21 25 32 35 38 40 50 21,0 25,0 32,0 35,0 38,0 40,0 50,0 ± 1,25 130 150 175 200 225 225 275
7.2 Minimum thickness of lining and cover When measured in accordance with EN ISO 4671, the thickness of the lining shall not be less than 1,6 mm. The thickness of the cover shall not be less than 1,0 mm. 7.3 Concentricity When determined in accordance with EN ISO 4671, the concentricity, based on a total indicator reading between the internal diameter and the outside surface of the cover, shall not exceed 1,0 mm.
7.4 Tolerance on cut lengths For cut lengths, the tolerances on length shall be in accordance with EN ISO 1307. The length of a hose assembly shall be measured from sealing face to sealing face of the end fittings with a tolerance from the nominal length of ± 1%. 8 Physical properties 8.1 Compounds When tested in accordance with the methods specified in Table 2, the physical properties of the compounds used for the lining and cover shall comply with the values specified in Table 2. Tests shall be performed either on samples taken from the hose or from moulded vulcanised sheets at a thickness of 2 mm or moulded test pieces, vulcanised to the same cured state as the production hoses. SIST EN 1360:2013
EN 1360:2013 (E) 8
Table 2 — Physical properties of compounds Property Unit Requirement Test piecea
Test method Rubber TPE Tensile strength
Lining and cover,
min.
MPa
9
12
Test piece cut from hose or from test sheet
ISO 37 Elongation at break
Lining and cover,
min. %
250
350 Accelerated ageing - Tensile strength change max.
Lining and cover,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.