SIST EN ISO 13680:2012
(Main)Petroleum and natural gas industries - Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock - Technical delivery conditions (ISO 13680:2010)
Petroleum and natural gas industries - Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock - Technical delivery conditions (ISO 13680:2010)
ISO 13680:2010 specifies the technical delivery conditions for corrosion-resistant alloy seamless tubulars for casing, tubing and coupling stock for two product specification levels: PSL-1, which is the basis of ISO 13680:2010; PSL-2, which provides additional requirements for a product that is intended to be both corrosion resistant and cracking resistant for the environments and qualification method specified in ISO 15156-3 and Annex G of ISO 13680:2010.
At the option of the manufacturer, PSL-2 products can be provided in lieu of PSL-1.
The corrosion-resistant alloys included in ISO 13680:2010 are special alloys in accordance with ISO 4948-1 and ISO 4948-2.
ISO 13680:2010 is applicable to the following four groups of product: group 1, which is composed of stainless alloys with a martensitic or martensitic/ferritic structure; group 2, which is composed of stainless alloys with a ferritic-austenitic structure, such as duplex and super-duplex stainless alloy; group 3, which is composed of stainless alloys with an austenitic structure (iron base); group 4, which is composed of nickel-based alloys with an austenitic structure (nickel base).
ISO 13680:2010 contains no provisions relating to the connection of individual lengths of pipe.
Erdöl- und Erdgasindustrie - Nahtlose Rohre aus korrosionsbeständigen Legierungen zur Verwendung als Futter- oder Steigrohre sowie Muffenvorrohre - Technische Lieferbedingungen (ISO 13680:2010)
Industries du pétrole et du gaz naturel - Tubes sans soudure en acier allié résistant à la corrosion utilisés comme tubes de cuvelage, tubes de production et tubes-ébauches pour manchons - Conditions techniques de livraison (ISO 13680:2010)
L'ISO 13680:2010 spécifie les conditions techniques de livraison des tubes sans soudure en acier allié résistant à la corrosion utilisés comme tubes de cuvelage, tubes de production et tubes-ébauches pour deux niveaux de spécification de produits (PSL): le niveau de spécification produit PSL-1 qui constitue la base de l'ISO 13680:2010 et le niveau de spécification produit PSL-2 qui spécifie des exigences supplémentaires applicables aux produits conçus pour être résistants à la corrosion et aux craquelures dans les environnements et avec la méthode de qualification spécifiée dans l'ISO 15156-3 et l'Annexe G de l'ISO 13680:2010.
Si le fabricant le décide, les produits de PSL-2 peuvent être fournis à la place des produits de PSL-1.
Les alliages résistants à la corrosion mentionnés dans l'ISO 13680:2010 sont des alliages spéciaux conformes à l'ISO 4948-1 et à l'ISO 4948-2.
L'ISO 13680:2010 s'applique aux quatre groupes de produits suivants: le groupe 1, composé d'alliages inoxydables d'une structure martensitique ou martensitique/ferritique, le groupe 2, constitué d'alliages inoxydables d'une structure ferritique-austénitique, tels que l'alliage d'acier inoxydable duplex et super duplex, le groupe 3, composé d'alliages inoxydables d'une structure austénitique (base ferreuse), et le groupe 4, constitué d'alliages à base de nickel d'une structure austénitique (base de nickel).
L'ISO 13680:2010 ne contient aucune disposition relative au raccordement de différentes longueurs de tube.
Industrija za predelavo nafte in zemeljskega plina - Nevarjene cevi iz korozijsko odpornih zlitin, ki se uporabljajo kot zaščitne, proizvodne in priključne cevi - Tehnični dobavni pogoji (ISO 13680:2010)
Ta mednarodni standard določa tehnične dobavne pogoje za nevarjene cevi iz korozijsko odpornih zlitin za zaščitne, proizvodne in priključne cevi za dve ravni specifikacije proizvoda: - PSL-1, ki je osnova tega mednarodnega standarda; - PSL-2, ki podaja dodatne zahteve za proizvod, ki je odporen proti koroziji in nastanku razpok v okolju, in kvalifikacijsko metodo, določeno v ISO 15156-3 in dodatku G tega mednarodnega standarda. Po izbiri proizvajalca se namesto proizvodov PSL-2 lahko zagotovijo proizvodi PSL-2.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 13680:2012
01-januar-2012
1DGRPHãþD
SIST EN ISO 13680:2008
,QGXVWULMD]DSUHGHODYRQDIWHLQ]HPHOMVNHJDSOLQD1HYDUMHQHFHYLL]NRUR]LMVNR
RGSRUQLK]OLWLQNLVHXSRUDEOMDMRNRW]DãþLWQHSURL]YRGQHLQSULNOMXþQHFHYL
7HKQLþQLGREDYQLSRJRML ,62
Petroleum and natural gas industries - Corrosion-resistant alloy seamless tubes for use
as casing, tubing and coupling stock - Technical delivery conditions (ISO 13680:2010)
Erdöl- und Erdgasindustrie - Nahtlose Rohre aus korrosionsbeständigen Legierungen zur
Verwendung als Futter- oder Steigrohre sowie Muffenvorrohre - Technische
Lieferbedingungen (ISO 13680:2010)
Industries du pétrole et du gaz naturel - Tubes sans soudure en acier allié résistant à la
corrosion utilisés comme tubes de cuvelage, tubes de production et tubes-ébauches
pour manchons - Conditions techniques de livraison (ISO 13680:2010)
Ta slovenski standard je istoveten z: EN ISO 13680:2010
ICS:
75.180.10 Oprema za raziskovanje in Exploratory and extraction
odkopavanje equipment
77.140.75 Jeklene cevi in cevni profili Steel pipes and tubes for
za posebne namene specific use
SIST EN ISO 13680:2012 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 13680:2012
---------------------- Page: 2 ----------------------
SIST EN ISO 13680:2012
EUROPEAN STANDARD
EN ISO 13680
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2010
ICS 75.180.10; 77.140.75 Supersedes EN ISO 13680:2008
English Version
Petroleum and natural gas industries - Corrosion-resistant alloy
seamless tubes for use as casing, tubing and coupling stock -
Technical delivery conditions (ISO 13680:2010)
Industries du pétrole et du gaz naturel - Tubes sans Erdöl- und Erdgasindustrie - Nahtlose Rohre aus
soudure en acier allié résistant à la corrosion utilisés korrosionsbeständigen Legierungen zur Verwendung als
comme tubes de cuvelage, tubes de production et tubes- Futter- oder Steigrohre sowie Muffenvorrohre - Technische
ébauches pour manchons - Conditions techniques de Lieferbedingungen (ISO 13680:2010)
livraison (ISO 13680:2010)
This European Standard was approved by CEN on 30 August 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13680:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 13680:2012
EN ISO 13680:2010 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 13680:2012
EN ISO 13680:2010 (E)
Foreword
This document (EN ISO 13680:2010) has been prepared by Technical Committee ISO/TC 67 "Materials,
equipment and offshore structures for petroleum, petrochemical and natural gas industries" in collaboration
with Technical Committee CEN/TC 12 “Materials, equipment and offshore structures for petroleum,
petrochemical and natural gas industries” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by March 2011, and conflicting national standards shall be withdrawn at
the latest by March 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 13680:2008.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 13680:2010 has been approved by CEN as a EN ISO 13680:2010 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 13680:2012
---------------------- Page: 6 ----------------------
SIST EN ISO 13680:2012
INTERNATIONAL ISO
STANDARD 13680
Third edition
2010-09-01
Petroleum and natural gas industries —
Corrosion-resistant alloy seamless tubes
for use as casing, tubing and coupling
stock — Technical delivery conditions
Industries du pétrole et du gaz naturel — Tubes sans soudure en acier
allié résistant à la corrosion utilisés comme tubes de cuvelage, tubes de
production et tubes-ébauches pour manchons — Conditions techniques
de livraison
Reference number
ISO 13680:2010(E)
©
ISO 2010
---------------------- Page: 7 ----------------------
SIST EN ISO 13680:2012
ISO 13680:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 13680:2012
ISO 13680:2010(E)
Contents Page
Foreword .v
Introduction.vi
1 Scope.1
2 Conformance .2
2.1 Dual normative references .2
2.2 Units of measurement.2
3 Normative references.2
4 Terms, abbreviated terms, symbols and definitions .4
4.1 Terms and definitions .4
4.2 Symbols.7
4.3 Abbreviated terms.7
5 Information to be supplied by the purchaser .8
6 Manufacturing process.9
6.1 Manufacturing of corrosion-resistant alloys .9
6.2 Product manufacturing process .9
6.3 Pipe end sizing .10
6.4 Straightening .10
6.5 Process requiring validation .10
6.6 Traceability.10
7 Material requirements .11
7.1 Chemical composition .11
7.2 Tensile properties.11
7.3 Hardness properties.11
7.4 Charpy V-notch test properties — General requirements.11
7.5 Charpy V-notch — Absorbed energy requirements for coupling stock — All grades.12
7.6 Charpy V-notch — Absorbed energy requirements for pipe — All grades.13
7.7 Flattening requirements.14
7.8 Corrosion properties.15
7.9 Microstructure properties.15
7.10 Surface condition .15
7.11 Defects.15
7.12 Hydrostatic test .16
8 Dimensions, masses and tolerances .16
8.1 Outside diameter, wall thickness and mass.16
8.2 Length.17
8.3 Tolerances.17
8.4 Product ends.17
9 Inspection and testing .17
9.1 Test equipment.17
9.2 Type and frequency of tests.18
9.3 Testing of chemical composition .18
9.4 Testing of mechanical characteristics .19
9.5 Tensile test.19
9.6 Hardness test.20
9.7 Impact or flattening test.20
9.8 Microstructural examination .23
9.9 Dimensional testing .23
© ISO 2010 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 13680:2012
ISO 13680:2010(E)
9.10 Drift test .24
9.11 Length .24
9.12 Straightness .24
9.13 Mass determination .24
9.14 Hydrostatic test.25
9.15 Visual inspection .25
9.16 Non-destructive examination .26
10 Surface treatment .31
10.1 Group 1 .31
10.2 Groups 2, 3 and 4.31
11 Marking .31
11.1 General.31
11.2 Marking on the product.32
11.3 Date of manufacture .33
12 Surface protection — Group 1.33
13 Documents .33
13.1 Electronic media .33
13.2 Retention of records.34
13.3 Test certificates.34
14 Handling, packaging and storage .35
14.1 General.35
14.2 Handling.35
14.3 Packaging .35
14.4 Storage.35
Annex A (normative) Tables in SI units .36
Annex B (normative) Figures in SI (USC) Units .56
Annex C (normative) Tables in USC units .61
Annex D (normative) Purchaser inspection .81
Annex E (normative) Cleanliness requirements .82
Annex F (informative) Use of the API Monogram by Licensees.84
Annex G (normative) Product specification level 2 (PSL-2) .87
Bibliography .89
iv © ISO 2010 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 13680:2012
ISO 13680:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 13680 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures
for petroleum, petrochemical and natural gas industries, Subcommittee SC 5, Casing, tubing and drill pipe.
This third edition cancels and replaces the second edition (ISO 13680:2008), of which is constitutes a minor
revision, with changes to 4.1.2; 4.1.14; 4.1.16; 4.1.19; 5.2 p) and 5.2 q); 6.1; 6.5; 6.6; 7.2; 7.7; 7.11.1 and
7.11.2; 9.3.3; 9.8.2; 9.8.3; 9.16.7; 9.16.13; 9.16.14; 11.2.4; 13.3; and Tables A.1, A.27, A.28, C.2, C.15, C.18,
C.27 and C.28.
It is the intent of ISO/TC 67 that the second and third edition of ISO 13680 both be applicable, at the option of
the purchaser, for a period of six months from the first day of the calendar quarter immediately following the
date of publication of this third edition, after which period the second edition will no longer be applicable.
© ISO 2010 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 13680:2012
ISO 13680:2010(E)
Introduction
It is necessary that users of this International Standard be aware that further or differing requirements can be
needed for individual applications. This International Standard is not intended to inhibit a vendor from offering,
or the purchaser from accepting, alternative equipment or engineering solutions for the individual application.
This can be particularly applicable where there is innovative or developing technology. Where an alternative is
offered, it is the responsibility of the vendor to identify any variations from this International Standard and
provide details.
This International Standard includes provisions of various nature. These are identified by the use of certain
verbal forms:
SHALL is used to indicate that a provision is MANDATORY;
SHOULD is used to indicate that a provision is not mandatory, but RECOMMENDED as good practice;
MAY is used to indicate that a provision is OPTIONAL.
vi © ISO 2010 – All rights reserved
---------------------- Page: 12 ----------------------
SIST EN ISO 13680:2012
INTERNATIONAL STANDARD ISO 13680:2010(E)
Petroleum and natural gas industries — Corrosion-resistant
alloy seamless tubes for use as casing, tubing and coupling
stock — Technical delivery conditions
WARNING — It is the purchaser's responsibility to specify the product specification level (PSL),
corrosion-resistant alloy (CRA) group, category, grade, delivery conditions and any other
requirements in addition to those specified herewith to ensure that the product is adequate for the
intended service environment. ISO 15156 (all parts) or NACE MR0175/ISO 15156 should be considered
when making specific requirements for H S-containing environment; see Annex G.
2
1 Scope
This International Standard specifies the technical delivery conditions for corrosion-resistant alloy seamless
tubulars for casing, tubing and coupling stock for two product specification levels:
⎯ PSL-1, which is the basis of this International Standard;
⎯ PSL-2, which provides additional requirements for a product that is intended to be both corrosion resistant
and cracking resistant for the environments and qualification method specified in ISO 15156-3 and
Annex G of this International Standard.
At the option of the manufacturer, PSL-2 products can be provided in lieu of PSL-1.
NOTE 1 The corrosion-resistant alloys included in this International Standard are special alloys in accordance with
ISO 4948-1 and ISO 4948-2.
This International Standard is applicable to the following four groups of product:
a) group 1, which is composed of stainless alloys with a martensitic or martensitic/ferritic structure;
b) group 2, which is composed of stainless alloys with a ferritic-austenitic structure, such as duplex and
super-duplex stainless alloy;
c) group 3, which is composed of stainless alloys with an austenitic structure (iron base);
d) group 4, which is composed of nickel-based alloys with an austenitic structure (nickel base).
This International Standard contains no provisions relating to the connection of individual lengths of pipe.
NOTE 2 The connection or joining method can influence the corrosion performance of the materials specified in this
International Standard.
NOTE 3 It is necessary to recognize that not all PSL-1 categories and grades can be made cracking resistant in
accordance with ISO 15156-3 and are, therefore, not included in PSL-2.
© ISO 2010 – All rights reserved 1
---------------------- Page: 13 ----------------------
SIST EN ISO 13680:2012
ISO 13680:2010(E)
2 Conformance
2.1 Dual normative references
In the interests of worldwide application of this International Standard, ISO/TC 67 has decided, after detailed
technical analysis, that certain of the normative documents listed in Clause 3 and prepared by ISO/TC 67 or
another ISO Technical Committee are interchangeable in the context of the relevant requirement with the
relevant document prepared by the American Petroleum Institute (API), the American Society for Testing and
Materials (ASTM) or the American National Standards Institute (ANSI). These latter documents are cited in
the running text following the ISO reference and preceded by “or”, for example “ISO XXXX or API YYYY”.
Application of an alternative normative document cited in this manner can lead to technical results that differ
from the use of the preceding ISO reference. However, both results are acceptable and these documents are,
thus, considered interchangeable in practice.
2.2 Units of measurement
In this International Standard, data are expressed in both the International System (SI) of units and the United
States Customary (USC) or other system of units. For a specific order item, it is intended that only one system
of units be used, without combining data expressed in the other system.
Products manufactured to specifications expressed in either of these unit systems shall be considered
equivalent and totally interchangeable. Consequently, compliance with the requirements of this International
Standard as expressed in one system provides compliance with requirements expressed in the other system.
For data expressed in SI units, a comma is used as the decimal separator and a space as the thousands
separator.
For data expressed in USC units, a dot (on the line) is used as the decimal separator and a space as the
thousands separator.
In the text, data in SI units are followed by data in USC or other units in parentheses.
Separate tables for data expressed in SI units and USC units are given in Annex A and Annex C, respectively.
Figures are contained in Annex B and express data in both SI and USC units.
3 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 377, Steel and steel products — Location and preparation of samples and test pieces for mechanical
testing
ISO 404, Steel and steel products — General technical delivery requirements
ISO 525, Bonded abrasive products — General requirements
ISO 783, Metallic materials — Tensile testing at elevated temperature
ISO 4885, Ferrous products — Heat treatments — Vocabulary
ISO 4948-1, Steels — Classification — Part 1: Classification of steels into unalloyed and alloy steels based on
chemical composition
2 © ISO 2010 – All rights reserved
---------------------- Page: 14 ----------------------
SIST EN ISO 13680:2012
ISO 13680:2010(E)
ISO 4948-2, Steels — Classification — Part 2: Classification of unalloyed and alloy steels according to main
quality classes and main property or application characteristics
ISO 6508-1, Metallic materials — Rockwell hardness test — Part 1: Test method (scales A, B, C, D, E, F, G,
H, K, N, T)
ISO 6892-1, Metallic materials — Tensile testing — Part 1: Method of test at room temperature
ISO 6929, Steel products — Definitions and classification
ISO 8501-1:2007, Preparation of steel substrates before application of paints and related products — Visual
assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel
substrates and of steel substrates after overall removal of previous coatings
ISO 9303, Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes — Full
peripheral ultrasonic testing for the detection of longitudinal imperfections
ISO 9304, Seamless and welded (except submerged
...
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Industries du pétrole et du gaz naturel - Tubes sans soudure en acier allié résistant à la corrosion utilisés comme tubes de cuvelage, tubes de production et tubes-ébauches pour manchons - Conditions techniques de livraison (ISO/FDIS 13680:2010)Petroleum and natural gas industries - Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock - Technical delivery conditions (ISO/FDIS 13680:2010)77.140.75Jeklene cevi in cevni profili za posebne nameneSteel pipes and tubes for specific use75.180.10Oprema za raziskovanje in odkopavanjeExploratory and extraction equipmentICS:Ta slovenski standard je istoveten z:FprEN ISO 13680kSIST FprEN ISO 13680:2010en01-junij-2010kSIST FprEN ISO 13680:2010SLOVENSKI
STANDARD
kSIST FprEN ISO 13680:2010
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
FINAL DRAFT
FprEN ISO 13680
April 2010 ICS 77.140.75; 75.180.10 Will supersede EN ISO 13680:2008English Version
Petroleum and natural gas industries - Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock - Technical delivery conditions (ISO/FDIS 13680:2010)
Industries du pétrole et du gaz naturel - Tubes sans soudure en acier allié résistant à la corrosion utilisés comme tubes de cuvelage, tubes de production et tubes-ébauches pour manchons - Conditions techniques de livraison (ISO/FDIS 13680:2010)
This draft European Standard is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee CEN/TC 12.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. FprEN ISO 13680:2010: EkSIST FprEN ISO 13680:2010
FprEN ISO 13680:2010 (E) 2 Contents Page Foreword .3 kSIST FprEN ISO 13680:2010
FprEN ISO 13680:2010 (E) 3 Foreword This document (FprEN ISO 13680:2010) has been prepared by Technical Committee ISO/TC 67 "Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries" in collaboration with Technical Committee CEN/TC 12 “Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries” the secretariat of which is held by AFNOR. This document is currently submitted to the Unique Acceptance Procedure. This document will supersede EN ISO 13680:2008. Endorsement notice The text of ISO/FDIS 13680:2010 has been approved by CEN as a FprEN ISO 13680:2010 without any modification.
kSIST FprEN ISO 13680:2010
kSIST FprEN ISO 13680:2010
Please see the administrative notes on page iii
RECIPIENTS OF THIS DRAFT ARE INVITED TOSUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICHTHEY ARE AWARE AND TO PROVIDE SUPPORT-ING DOCUMENTATION. IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-LOGICAL, COMMERCIAL AND USER PURPOSES,DRAFT INTERNATIONAL STANDARDS MAY ONOCCASION HAVE TO BE CONSIDERED IN THELIGHT OF THEIR POTENTIAL TO BECOME STAN-DARDS TO WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
Reference numberISO/FDIS 13680:2010(E)© ISO 2010 FINAL DRAFT ISO/TC 67/SC 5 Secretariat: JISC Voting begins on: 2010-04-29 Voting terminates on: 2010-06-29
INTERNATIONAL STANDARD ISO/FDIS13680Petroleum and natural gas industries — Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock — Technical delivery conditions Industries du pétrole et du gaz naturel — Tubes sans soudure en acier allié résistant à la corrosion utilisés comme tubes de cuvelage, tubes de production et tubes-ébauches pour manchons — Conditions techniques de livraison
kSIST FprEN ISO 13680:2010
ISO/FDIS 13680:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
Copyright notice This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted under the applicable laws of the user's country, neither this ISO draft nor any extract from it may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission being secured. Requests for permission to reproduce should be addressed to either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Reproduction may be subject to royalty payments or a licensing agreement. Violators may be prosecuted.
ii © ISO 2010 – All rights reserved
kSIST FprEN ISO 13680:2010
ISO/FDIS 13680:2010(E) © ISO 2010 – All rights reserved iii ISO/CEN PARALLEL PROCESSING This Minor Revision has been developed within the International Organization for Standardization (ISO), and processed under the ISO-lead mode of collaboration as defined in the Vienna Agreement. This final draft is hereby submitted to a parallel two-month approval vote in ISO and three-month UAP vote in CEN. Positive votes shall not be accompanied by comments. Negative votes shall be accompanied by the relevant technical reasons.
In accordance with the provisions of Council Resolution 15/1993, this document is circulated in the English language only.
kSIST FprEN ISO 13680:2010
ISO/FDIS 13680:2010(E) iv © ISO 2010 – All rights reserved Contents Page Foreword.vi Introduction.vii 1 Scope.1 2 Conformance.2 2.1 Dual normative references.2 2.2 Units of measurement.2 3 Normative references.2 4 Terms, abbreviated terms, symbols and definitions.4 4.1 Terms and definitions.4 4.2 Symbols.6 4.3 Abbreviated terms.7 5 Information to be supplied by the purchaser.8 6 Manufacturing process.9 6.1 Manufacturing of corrosion-resistant alloys.9 6.2 Product manufacturing process.9 6.3 Pipe end sizing.9 6.4 Straightening.10 6.5 Process requiring validation.10 6.6 Traceability.10 7 Material requirements.10 7.1 Chemical composition.10 7.2 Tensile properties.11 7.3 Hardness properties.11 7.4 Charpy V-notch test properties — General requirements.11 7.5 Charpy V-notch — Absorbed energy requirements for coupling stock — All grades.12 7.6 Charpy V-notch — Absorbed energy requirements for pipe — All grades.13 7.7 Flattening requirements.14 7.8 Corrosion properties.15 7.9 Microstructure properties.15 7.10 Surface condition.15 7.11 Defects.15 7.12 Hydrostatic test.16 8 Dimensions, masses and tolerances.16 8.1 Outside diameter, wall thickness and mass.16 8.2 Length.17 8.3 Tolerances.17 8.4 Product ends.17 9 Inspection and testing.17 9.1 Test equipment.17 9.2 Type and frequency of tests.18 9.3 Testing of chemical composition.18 9.4 Testing of mechanical characteristics.19 9.5 Tensile test.19 9.6 Hardness test.20 9.7 Impact or flattening test.20 9.8 Microstructural examination.23 9.9 Dimensional testing.23 kSIST FprEN ISO 13680:2010
ISO/FDIS 13680:2010(E) © ISO 2010 – All rights reserved v 9.10 Drift test.24 9.11 Length.24 9.12 Straightness.24 9.13 Mass determination.24 9.14 Hydrostatic test.25 9.15 Visual inspection.25 9.16 Non-destructive examination.26 10 Surface treatment.31 10.1 Group 1.31 10.2 Groups 2, 3 and 4.31 11 Marking.31 11.1 General.31 11.2 Marking on the product.32 11.3 Date of manufacture.33 12 Surface protection — Group 1.33 13 Documents.33 13.1 Electronic media.33 13.2 Retention of records.34 13.3 Test certificates.34 14 Handling, packaging and storage.35 14.1 General.35 14.2 Handling.35 14.3 Packaging.35 14.4 Storage.35 Annex A (normative)
Tables in SI units.36 Annex B (normative)
Figures in SI (USC) Units.56 Annex C (normative)
Tables in USC units.61 Annex D (normative)
Purchaser inspection.81 Annex E (normative)
Cleanliness requirements.82 Annex F (informative)
Marking instructions for API licensees — API monogram.84 Annex G (normative)
Product specification level 2 (PSL-2).85 Bibliography.87
kSIST FprEN ISO 13680:2010
ISO/FDIS 13680:2010(E) vi © ISO 2010 – All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 13680 was prepared by Technical Committee ISO/TC 67, Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries, Subcommittee SC 5, Casing, tubing and drill pipe. This third edition cancels and replaces the second edition (ISO 13680:2008), of which is constitutes a minor revision, with changes to 4.1.2; 4.1.14; 4.1.16; 4.1.19; 5.2 p) and 5.2 q); 6.1; 6.5; 6.6; 7.2; 7.7; 7.11.1 and 7.11.2; 9.3.3; 9.8.2; 9.8.3; 9.16.7; 9.16.13; 9.16.14; 11.2.4; 13.3; and Tables A.1, C.2, C.15 and C.18. It is the intent of ISO/TC 67 that the second and third edition of ISO 13680 both be applicable, at the option of the purchaser, for a period of six months from the first day of the calendar quarter immediately following the date of publication of this third edition, after which period the second edition will no longer be applicable. kSIST FprEN ISO 13680:2010
ISO/FDIS 13680:2010(E) © ISO 2010 – All rights reserved vii Introduction It is necessary that users of this International Standard be aware that further or differing requirements can be needed for individual applications. This International Standard is not intended to inhibit a vendor from offering, or the purchaser from accepting, alternative equipment or engineering solutions for the individual application. This can be particularly applicable where there is innovative or developing technology. Where an alternative is offered, it is the responsibility of the vendor to identify any variations from this International Standard and provide details. This International Standard includes provisions of various nature. These are identified by the use of certain verbal forms: SHALL is used to indicate that a provision is MANDATORY; SHOULD is used to indicate that a provision is not mandatory, but RECOMMENDED as good practice; MAY is used to indicate that a provision is OPTIONAL.
kSIST FprEN ISO 13680:2010
kSIST FprEN ISO 13680:2010
FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 13680:2010(E) © ISO 2010 – All rights reserved 1 Petroleum and natural gas industries — Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock — Technical delivery conditions WARNING — It is the purchaser's responsibility to specify the product specification level (PSL), corrosion-resistant alloy (CRA) group, category, grade, delivery conditions and any other requirements in addition to those specified herewith to ensure that the product is adequate for the intended service environment. ISO 15156 (all parts) or NACE MR0175/ISO 15156 should be considered when making specific requirements for H2S-containing environment; see Annex G. 1 Scope This International Standard specifies the technical delivery conditions for corrosion-resistant alloy seamless tubulars for casing, tubing and coupling stock for two product specification levels: ⎯ PSL-1, which is the basis of this International Standard; ⎯ PSL-2, which provides additional requirements for a product that is intended to be both corrosion resistant and cracking resistant for the environments and qualification method specified in ISO 15156-3 and Annex G of this International Standard. At the option of the manufacturer, PSL-2 products can be provided in lieu of PSL-1. NOTE 1 The corrosion-resistant alloys included in this International Standard are special alloys in accordance with ISO 4948-1 and ISO 4948-2. This International Standard is applicable to the following four groups of product: a) group 1, which is composed of stainless alloys with a martensitic or martensitic/ferritic structure; b) group 2, which is composed of stainless alloys with a ferritic-austenitic structure, such as duplex and super-duplex stainless alloy; c) group 3, which is composed of stainless alloys with an austenitic structure (iron base); d) group 4, which is composed of nickel-based alloys with an austenitic structure (nickel base). This International Standard contains no provisions relating to the connection of individual lengths of pipe. NOTE 2 The connection or joining method can influence the corrosion performance of the materials specified in this International Standard. NOTE 3 It is necessary to recognize that not all PSL-1 categories and grades can be made cracking resistant in accordance with ISO 15156-3 and are, therefore, not included in PSL-2. kSIST FprEN ISO 13680:2010
ISO/FDIS 13680:2010(E) 2 © ISO 2010 – All rights reserved 2 Conformance 2.1 Dual normative references In the interests of worldwide application of this International Standard, ISO/TC 67 has decided, after detailed technical analysis, that certain of the normative documents listed in Clause 3 and prepared by ISO/TC 67 or another ISO Technical Committee are interchangeable in the context of the relevant requirement with the relevant document prepared by the American Petroleum Institute (API), the American Society for Testing and Materials (ASTM) or the American National Standards Institute (ANSI). These latter documents are cited in the running text following the ISO reference and preceded by “or”, for example “ISO XXXX or API YYYY”. Application of an alternative normative document cited in this manner can lead to technical results that differ from the use of the preceding ISO reference. However, both results are acceptable and these documents are, thus, considered interchangeable in practice. 2.2 Units of measurement In this International Standard, data are expressed in both the International System (SI) of units and the United States Customary (USC) or other system of units. For a specific order item, it is intended that only one system of units be used, without combining data expressed in the other system. Products manufactured to specifications expressed in either of these unit systems shall be considered equivalent and totally interchangeable. Consequently, compliance with the requirements of this International Standard as expressed in one system provides compliance with requirements expressed in the other system. For data expressed in SI units, a comma is used as the decimal separator and a space as the thousands separator. For data expressed in USC units, a dot (on the line) is used as the decimal separator and a space as the thousands separator. In the text, data in SI units are followed by data in USC or other units in parentheses. Separate tables for data expressed in SI units and USC units are given in Annex A and Annex C, respectively. Figures are contained in Annex B and express data in both SI and USC units. 3 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 377, Steel and steel products — Location and preparation of samples and test pieces for mechanical testing ISO 404, Steel and steel products — General technical delivery requirements ISO 525, Bonded abrasive products — General requirements ISO 783, Metallic materials — Tensile testing at elevated temperature ISO 4885, Ferrous products — Heat treatments — Vocabulary ISO 4948-1, Steels — Classification — Part 1: Classification of steels into unalloyed and alloy steels based on chemical composition kSIST FprEN ISO 13680:2010
ISO/FDIS 13680:2010(E) © ISO 2010 – All rights reserved 3 ISO 4948-2, Steels — Classification — Part 2: Classification of unalloyed and alloy steels according to main quality classes and main property or application characteristics ISO 6508-1, Metallic materials — Rockwell hardness test — Part 1: Test method (scales A, B, C, D, E, F, G, H, K, N, T) ISO 6892-1, Metallic materials — Tensile testing — Part 1: Method of test at room temperature ISO 6929, Steel products — Definitions and classification ISO 8501-1:2007, Preparation of steel substrates before application of paints and related products — Visual assessment of surface cleanliness — Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings ISO 9303, Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes — Full peripheral ultrasonic testing for the detection of longitudinal imperfections ISO 9304, Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes — Eddy current testing for the detection of imperfections ISO 9305, Seamless steel tubes for pressure purposes — Full peripheral ultrasonic testing for the detection of transverse imperfections ISO 9402, Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes — Full peripheral magnetic transducer/flux leakage testing of ferromagnetic steel tubes for the detection of longitudinal imperfections ISO 9598, Seamless steel tubes for pressure purposes — Full peripheral magnetic transducer/flux leakage testing of ferromagnetic steel tubes for the detection of transverse imperfections ISO 10124, Seamless and welded (except submerged arc-welded) steel tubes for pressure purposes — Ultrasonic testing for the detection of laminar imperfections ISO 1047
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.