EN ISO 13680:2010
(Main)Petroleum and natural gas industries - Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock - Technical delivery conditions (ISO 13680:2010)
Petroleum and natural gas industries - Corrosion-resistant alloy seamless tubes for use as casing, tubing and coupling stock - Technical delivery conditions (ISO 13680:2010)
ISO 13680:2010 specifies the technical delivery conditions for corrosion-resistant alloy seamless tubulars for casing, tubing and coupling stock for two product specification levels: PSL-1, which is the basis of ISO 13680:2010; PSL-2, which provides additional requirements for a product that is intended to be both corrosion resistant and cracking resistant for the environments and qualification method specified in ISO 15156-3 and Annex G of ISO 13680:2010.
At the option of the manufacturer, PSL-2 products can be provided in lieu of PSL-1.
The corrosion-resistant alloys included in ISO 13680:2010 are special alloys in accordance with ISO 4948-1 and ISO 4948-2.
ISO 13680:2010 is applicable to the following four groups of product: group 1, which is composed of stainless alloys with a martensitic or martensitic/ferritic structure; group 2, which is composed of stainless alloys with a ferritic-austenitic structure, such as duplex and super-duplex stainless alloy; group 3, which is composed of stainless alloys with an austenitic structure (iron base); group 4, which is composed of nickel-based alloys with an austenitic structure (nickel base).
ISO 13680:2010 contains no provisions relating to the connection of individual lengths of pipe.
Erdöl- und Erdgasindustrie - Nahtlose Rohre aus korrosionsbeständigen Legierungen zur Verwendung als Futter- oder Steigrohre sowie Muffenvorrohre - Technische Lieferbedingungen (ISO 13680:2010)
Industries du pétrole et du gaz naturel - Tubes sans soudure en acier allié résistant à la corrosion utilisés comme tubes de cuvelage, tubes de production et tubes-ébauches pour manchons - Conditions techniques de livraison (ISO 13680:2010)
L'ISO 13680:2010 spécifie les conditions techniques de livraison des tubes sans soudure en acier allié résistant à la corrosion utilisés comme tubes de cuvelage, tubes de production et tubes-ébauches pour deux niveaux de spécification de produits (PSL): le niveau de spécification produit PSL-1 qui constitue la base de l'ISO 13680:2010 et le niveau de spécification produit PSL-2 qui spécifie des exigences supplémentaires applicables aux produits conçus pour être résistants à la corrosion et aux craquelures dans les environnements et avec la méthode de qualification spécifiée dans l'ISO 15156-3 et l'Annexe G de l'ISO 13680:2010.
Si le fabricant le décide, les produits de PSL-2 peuvent être fournis à la place des produits de PSL-1.
Les alliages résistants à la corrosion mentionnés dans l'ISO 13680:2010 sont des alliages spéciaux conformes à l'ISO 4948-1 et à l'ISO 4948-2.
L'ISO 13680:2010 s'applique aux quatre groupes de produits suivants: le groupe 1, composé d'alliages inoxydables d'une structure martensitique ou martensitique/ferritique, le groupe 2, constitué d'alliages inoxydables d'une structure ferritique-austénitique, tels que l'alliage d'acier inoxydable duplex et super duplex, le groupe 3, composé d'alliages inoxydables d'une structure austénitique (base ferreuse), et le groupe 4, constitué d'alliages à base de nickel d'une structure austénitique (base de nickel).
L'ISO 13680:2010 ne contient aucune disposition relative au raccordement de différentes longueurs de tube.
Industrija za predelavo nafte in zemeljskega plina - Nevarjene cevi iz korozijsko odpornih zlitin, ki se uporabljajo kot zaščitne, proizvodne in priključne cevi - Tehnični dobavni pogoji (ISO 13680:2010)
Ta mednarodni standard določa tehnične dobavne pogoje za nevarjene cevi iz korozijsko odpornih zlitin za zaščitne, proizvodne in priključne cevi za dve ravni specifikacije proizvoda: - PSL-1, ki je osnova tega mednarodnega standarda; - PSL-2, ki podaja dodatne zahteve za proizvod, ki je odporen proti koroziji in nastanku razpok v okolju, in kvalifikacijsko metodo, določeno v ISO 15156-3 in dodatku G tega mednarodnega standarda. Po izbiri proizvajalca se namesto proizvodov PSL-2 lahko zagotovijo proizvodi PSL-2.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2012
1DGRPHãþD
SIST EN ISO 13680:2008
,QGXVWULMD]DSUHGHODYRQDIWHLQ]HPHOMVNHJDSOLQD1HYDUMHQHFHYLL]NRUR]LMVNR
RGSRUQLK]OLWLQNLVHXSRUDEOMDMRNRW]DãþLWQHSURL]YRGQHLQSULNOMXþQHFHYL
7HKQLþQLGREDYQLSRJRML ,62
Petroleum and natural gas industries - Corrosion-resistant alloy seamless tubes for use
as casing, tubing and coupling stock - Technical delivery conditions (ISO 13680:2010)
Erdöl- und Erdgasindustrie - Nahtlose Rohre aus korrosionsbeständigen Legierungen zur
Verwendung als Futter- oder Steigrohre sowie Muffenvorrohre - Technische
Lieferbedingungen (ISO 13680:2010)
Industries du pétrole et du gaz naturel - Tubes sans soudure en acier allié résistant à la
corrosion utilisés comme tubes de cuvelage, tubes de production et tubes-ébauches
pour manchons - Conditions techniques de livraison (ISO 13680:2010)
Ta slovenski standard je istoveten z: EN ISO 13680:2010
ICS:
75.180.10 Oprema za raziskovanje in Exploratory and extraction
odkopavanje equipment
77.140.75 Jeklene cevi in cevni profili Steel pipes and tubes for
za posebne namene specific use
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 13680
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2010
ICS 75.180.10; 77.140.75 Supersedes EN ISO 13680:2008
English Version
Petroleum and natural gas industries - Corrosion-resistant alloy
seamless tubes for use as casing, tubing and coupling stock -
Technical delivery conditions (ISO 13680:2010)
Industries du pétrole et du gaz naturel - Tubes sans Erdöl- und Erdgasindustrie - Nahtlose Rohre aus
soudure en acier allié résistant à la corrosion utilisés korrosionsbeständigen Legierungen zur Verwendung als
comme tubes de cuvelage, tubes de production et tubes- Futter- oder Steigrohre sowie Muffenvorrohre - Technische
ébauches pour manchons - Conditions techniques de Lieferbedingungen (ISO 13680:2010)
livraison (ISO 13680:2010)
This European Standard was approved by CEN on 30 August 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13680:2010: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 13680:2010) has been prepared by Technical Committee ISO/TC 67 "Materials,
equipment and offshore structures for petroleum, petrochemical and natural gas industries" in collaboration
with Technical Committee CEN/TC 12 “Materials, equipment and offshore structures for petroleum,
petrochemical and natural gas industries” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by March 2011, and conflicting national standards shall be withdrawn at
the latest by March 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 13680:2008.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 13680:2010 has been approved by CEN as a EN ISO 13680:2010 without any modification.
INTERNATIONAL ISO
STANDARD 13680
Third edition
2010-09-01
Petroleum and natural gas industries —
Corrosion-resistant alloy seamless tubes
for use as casing, tubing and coupling
stock — Technical delivery conditions
Industries du pétrole et du gaz naturel — Tubes sans soudure en acier
allié résistant à la corrosion utilisés comme tubes de cuvelage, tubes de
production et tubes-ébauches pour manchons — Conditions techniques
de livraison
Reference number
ISO 13680:2010(E)
©
ISO 2010
ISO 13680:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
ISO 13680:2010(E)
Contents Page
Foreword .v
Introduction.vi
1 Scope.1
2 Conformance .2
2.1 Dual normative references .2
2.2 Units of measurement.2
3 Normative references.2
4 Terms, abbreviated terms, symbols and definitions .4
4.1 Terms and definitions .4
4.2 Symbols.7
4.3 Abbreviated terms.7
5 Information to be supplied by the purchaser .8
6 Manufacturing process.9
6.1 Manufacturing of corrosion-resistant alloys .9
6.2 Product manufacturing process .9
6.3 Pipe end sizing .10
6.4 Straightening .10
6.5 Process requiring validation .10
6.6 Traceability.10
7 Material requirements .11
7.1 Chemical composition .11
7.2 Tensile properties.11
7.3 Hardness properties.11
7.4 Charpy V-notch test properties — General requirements.11
7.5 Charpy V-notch — Absorbed energy requirements for coupling stock — All grades.12
7.6 Charpy V-notch — Absorbed energy requirements for pipe — All grades.13
7.7 Flattening requirements.14
7.8 Corrosion properties.15
7.9 Microstructure properties.15
7.10 Surface condition .15
7.11 Defects.15
7.12 Hydrostatic test .16
8 Dimensions, masses and tolerances .16
8.1 Outside diameter, wall thickness and mass.16
8.2 Length.17
8.3 Tolerances.17
8.4 Product ends.17
9 Inspection and testing .17
9.1 Test equipment.17
9.2 Type and frequency of tests.18
9.3 Testing of chemical composition .18
9.4 Testing of mechanical characteristics .19
9.5 Tensile test.19
9.6 Hardness test.20
9.7 Impact or flattening test.20
9.8 Microstructural examination .23
9.9 Dimensional testing .23
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.