SIST EN 12697-20:2012
(Main)Bituminous mixtures - Test methods for hot mix asphalt - Part 20: Indentation using cube or cylindrical specimens (CY)
Bituminous mixtures - Test methods for hot mix asphalt - Part 20: Indentation using cube or cylindrical specimens (CY)
This European Standard specifies a test method for determining the depth of indentation of mastic asphalt and other asphalt, when force is applied to them via a cylindrical indentor pin with a circular flat-ended base. This European Standard applies to aggregates of maximum nominal size less or equal to 16 mm.
Asphalt - Prüfverfahren für Heißasphalt - Teil 20: Eindringversuch an Würfeln oder zylindrischen Probekörpern
Diese Europäische Norm legt ein Prüfverfahren zur Bestimmung der Eindringtiefe von Gussasphalt und anderer Asphaltarten bei Beanspruchung mit einem zylindrischen Stempel mit kreisförmiger ebener Grundfläche fest. Diese Europäische Norm gilt für Gesteinskörnungen mit einer maximalen Nenngröße gleich oder kleiner als 16 mm.
Mélanges bitumineux - Méthodes d’essai pour mélange hydrocarboné à chaud - Partie 20: Essai de pénétration de cubes ou éprouvettes Marshall
La présente Norme européenne spécifie une méthode d’essai pour déterminer la profondeur d’indentation
d’un asphalte coulé et d’autres types d’enrobés sous l’effet d’une force exercée par l’intermédiaire d’un
poinçon cylindrique à embout plat circulaire. La présente Norme européenne s’applique à des granulats dont
la granulométrie nominale maximale est inférieure ou égale à 16 mm.
Bitumenske zmesi - Preskusne metode za vroče asfaltne zmesi - 20. del: Preskus z vtiskanjem na kocko ali valjaste preskušance (CY)
Ta evropski standard določa preskusno metodo za ugotavljanje globine vtisa v litem asfaltu ali drugem asfaltu, ko je podvržen sili prek valjastega vtisnega sornika z okroglo ploščato osnovo. Ta evropski standard se uporablja za agregate z največjo nominalno velikostjo, ki je manjša ali enaka 16 mm.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Asphalt - Prüfverfahren für Heißasphalt - Teil 20: Eindringversuch an Würfeln oder zylindrischen ProbekörpernMélanges bitumineux - Méthodes d’essai pour mélange hydrocarboné à chaud - Partie 20: Essai de pénétration de cubes ou éprouvettes MarshallBituminous mixtures - Test methods for hot mix asphalt - Part 20: Indentation using cube or cylindrical specimens (CY)93.080.20Materiali za gradnjo cestRoad construction materialsICS:Ta slovenski standard je istoveten z:EN 12697-20:2012SIST EN 12697-20:2012en,fr,de01-junij-2012SIST EN 12697-20:2012SLOVENSKI
STANDARDSIST EN 12697-20:20041DGRPHãþD
SIST EN 12697-20:2012
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12697-20
April 2012 ICS 93.080.20 Supersedes EN 12697-20:2003English Version
Bituminous mixtures - Test methods for hot mix asphalt - Part 20: Indentation using cube or cylindrical specimens (CY)
Mélanges bitumineux - Méthodes d'essai pour mélange hydrocarboné à chaud - Partie 20: Essai d'indentation sur cubes ou éprouvettes Marshall
Asphalt - Prüfverfahren für Heißasphalt - Teil 20: Eindringversuch an Würfeln oder zylindrischen Probekörpern This European Standard was approved by CEN on 26 February 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12697-20:2012: ESIST EN 12697-20:2012
EN 12697-20:2012 (E) 2 Contents Page Foreword .31Scope .72Normative references .73Apparatus .73.1Moulding of test cubes of mastic asphalt .73.2Indentation test apparatus .84Specimens . 144.1Specimen type . 144.2Number of specimens . 144.3Conditioning . 145Procedure . 145.1Checking . 145.2Test conditions . 145.3Cube specimen preparation . 155.4Cylindrical specimen preparation . 155.5Mounting and temperature conditioning of the specimens . 165.6Application of the force . 166Result . 167Precision . 168Test report . 17Bibliography . 18 SIST EN 12697-20:2012
EN 12697-20:2012 (E) 3 Foreword This document (EN 12697-20:2012) has been prepared by Technical Committee CEN/TC 227 “Road materials”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2012, and conflicting national standards shall be withdrawn at the latest by October 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12697-20:2003. The following is a list of significant technical changes since the previous edition: Marshall specimens (MS) changed to cylindrical specimens (CY) in the title and elsewhere; the scope changed to covering mastic asphalt and other asphalt rather than mastic asphalt and rolled asphalt to avoid confusion with hot rolled asphalt; parting agent corrected to release agent; the description of the indentation test apparatus is broken down into separate components; accuracy requirement given for the water bath; the requirement that cylindrical specimens should not be removed from the compaction mould has been removed; requirement on the storage of samples prior to testing has been added; the requirements for the preparation of both cube and cylindrical samples have been redrafted; precision statement edited. EN 12697-1, Bituminous mixtures — Test methods for hot mix asphalt — Part 1: Soluble binder content EN 12697-2, Bituminous mixtures — Test methods for hot mix asphalt — Part 2: Determination of particle size distribution EN 12697-3, Bituminous mixtures — Test methods for hot mix asphalt — Part 3: Bitumen recovery: Rotary evaporator EN 12697-4, Bituminous mixtures — Test methods for hot mix asphalt — Part 4: Bitumen recovery: Fractionating column EN 12697-5, Bituminous mixtures — Test methods for hot mix asphalt — Part 5: Determination of the maximum density EN 12697-6, Bituminous mixtures — Test methods for hot mix asphalt — Part 6: Determination of bulk density of bituminous specimens SIST EN 12697-20:2012
EN 12697-20:2012 (E) 4 EN 12697-7, Bituminous mixtures — Test methods for hot mix asphalt — Part 7: Determination of bulk density of bituminous specimens by gamma rays EN 12697-8, Bituminous mixtures — Test methods for hot mix asphalt — Part 8: Determination of void characteristics of bituminous specimens EN 12697-10, Bituminous mixtures — Test methods for hot mix asphalt — Part 10: Compactibility EN 12697-11, Bituminous mixtures — Test methods for hot mix asphalt — Part 11: Determination of the affinity between aggregate and bitumen EN 12697-12, Bituminous mixtures — Test methods for hot mix asphalt — Part 12: Determination of the water sensitivity of bituminous specimens EN 12697-13, Bituminous mixtures — Test methods for hot mix asphalt — Part 13: Temperature measurement EN 12697-14, Bituminous mixtures — Test methods for hot mix asphalt — Part 14: Water content EN 12697-15, Bituminous mixtures — Test methods for hot mix asphalt — Part 15: Determination of the segregation sensitivity EN 12697-16, Bituminous mixtures — Test methods for hot mix asphalt — Part 16: Abrasion by studded tyres EN 12697-17, Bituminous mixtures — Test methods for hot mix asphalt — Part 17: Partial loss of porous asphalt specimen EN 12697-18, Bituminous mixtures — Test methods for hot mix asphalt — Part 18: Binder drainage EN 12697-19, Bituminous mixtures — Test methods for hot mix asphalt — Part 19: Permeability of specimen EN 12697-20, Bituminous mixtures — Test methods for hot mix asphalt — Part 20: Indentation using cube or cylindrical specimens EN 12697-21, Bituminous mixtures — Test methods for hot mix asphalt — Part 21: Indentation using plate specimens EN 12697-22, Bituminous mixtures — Test methods for hot mix asphalt — Part 22: Wheel tracking EN 12697-23, Bituminous mixtures — Test methods for hot mix asphalt — Part 23: Determination of the indirect tensile strength of bituminous specimens EN 12697-24, Bituminous mixtures — Test methods for hot mix asphalt — Part 24: Resistance to fatigue EN 12697-25, Bituminous mixtures — Test methods for hot mix asphalt — Part 25: Cyclic compression test EN 12697-26, Bituminous mixtures — Test methods for hot mix asphalt — Part 26: Stiffness EN 12697-27, Bituminous mixtures — Test methods for hot mix asphalt — Part 27: Sampling EN 12697-28, Bituminous mixtures — Test methods for hot mix asphalt — Part 28: Preparation of samples for determining binder content, water content and grading EN 12697-29, Bituminous mixtures — Test methods for hot mix asphalt — Part 29: Determination of the dimensions of a bituminous specimen EN 12697-30, Bituminous mixtures — Test methods for hot mix asphalt — Part 30: Specimen preparation by impact compactor SIST EN 12697-20:2012
EN 12697-20:2012 (E) 5 EN 12697-31, Bituminous mixtures — Test methods for hot mix asphalt — Part 31: Specimen preparation by gyratory compactor EN 12697-32, Bituminous mixtures — Test methods for hot mix asphalt — Part 32: Laboratory compaction of bituminous mixtures by vibratory compactor EN 12697-33, Bituminous mixtures — Test methods for hot mix asphalt — Part 33: Specimen prepared by roller compactor EN 12697-34, Bituminous mixtures — Test methods for hot mix asphalt — Part 34: Marshall test EN 12697-35, Bituminous mixtures — Test methods for hot mix asphalt — Part 35: Laboratory mixing EN 12697-36, Bituminous mixtures — Test methods for hot mix asphalt — Part 36: Determination of the thickness of a bituminous pavement EN 12697-37, Bituminous mixtures — Test methods for hot mix asphalt — Part 37: Hot sand test for the adhesivity of binder on precoated chippings for HRA EN 12697-38, Bituminous mixtures — Test methods for hot mix asphalt — Part 38: Common equipment and calibration EN 12697-39, Bituminous mixtures — Test methods for hot mix asphalt — Part 39: Binder content by ignition EN 12697-40, Bituminous mixtures — Test methods for hot mix asphalt — Part 40: In situ drainability EN 12697-41, Bituminous mixtures — Test methods for hot mix asphalt — Part 41: Resistance to de-icing fluids EN 12697-42, Bituminous mixtures — Test methods for hot mix asphalt — Part 42: Amount of coarse foreign matters in reclaimed asphalt EN 12697-43, Bituminous mixtures — Test methods for hot mix asphalt — Part 43: Resistance to fuel EN 12697-44, Bituminous mixtures — Test methods for hot mix asphalt — Part 44: Crack propagation by semi-circular bending test prEN 12697-45, Bituminous mixtures — Test methods for hot mix asphalt — Part 45: Saturation ageing tensile stiffness (SATS) conditioning test prEN 12697-46, Bituminous mixtures — Test methods for hot mix asphalt — Part 46: Low temperature cracking and properties by uniaxial tension tests. EN 12697-47, Bituminous mixtures — Test methods for hot mix asphalt — Part 47: Determination of the ash content of natural asphalt prEN 12697-48, Bituminous mixtures — Test methods for hot mix asphalt — Part 48: Inter-layer bond strength1) prEN 12697-49, Bituminous mixtures — Test methods for hot mix asphalt — Part 49: Determination of friction after polishing.1) prEN 12697-50, Bituminous mixtures — Test methods for hot mix asphalt — Part 50: Scuffing resistance of surface course1)
1) In preparation SIST EN 12697-20:2012
EN 12697-20:2012 (E) 6 According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 12697-20:2012
EN 12697-20:2012 (E) 7 1 Scope This European Standard specifies a test method for determining the depth of indentation of mastic asphalt and other asphalt, when force is applied to them via a cylindrical indentor pin with a circular flat-ended base. This European Standard applies to aggregates of maximum nominal size less or equal to 16 mm. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 12697-27, Bituminous mixtures — Test methods for hot mix asphalt — Part 27: Sampling EN 12697-30, Bituminous mixtures — Test methods for hot mix asphalt — Part 30: Specimen preparation by impact compactor EN 12697-35, Bituminous mixtures — Test methods for hot mix asphalt — Part 35: Laboratory mixing EN 12970, Mastic asphalt for waterproofing — Definitions, requirements and test methods EN 13108-1, Bituminous
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.