SIST EN ISO 12821:2020
(Main)Glass packaging - 26 H 180 crown finish - Dimensions (ISO 12821:2019)
Glass packaging - 26 H 180 crown finish - Dimensions (ISO 12821:2019)
This technical standard specifies the dimensions of the 26 mm tall crown finish for glass bottles containing beverages. The tall crown finish is designed to use a metal crown cap (see e.g. EN 17177).
Verpackungen aus Glas - Kronenmundstück 26 H 180 - Maße (ISO 12821:2019)
Dieses Dokument legt die Maße des 26 mm hohen Kronenmundstückes für Getränkeflaschen aus Glas fest. Das hohe Kronenmundstück ist für die Verwendung eines Kronenverschlusses aus Metall ausgelegt (siehe z. B. EN 17177).
Emballage en verre - Bague couronne 26 H 180 - Dimensions (ISO 12821:2019)
Le présent document spécifie les dimensions des bagues couronnes hautes de 26 mm pour les bouteilles en verre destinées au conditionnement des boissons. La bague couronne haute est conçue pour être utilisée avec une capsule couronne métallique (voir par exemple la norme EN 17177).
Steklena embalaža - Kronsko grlo 26 H 180 - Mere (ISO 12821:2019)
Ta tehnični standard določa mere kronskega grla višine 26 mm za steklenice, ki vsebujejo pijače. Visoko kronsko grlo je zasnovano za uporabo s kovinskim kronskim pokrovčkom (glej npr. standard EN 17177).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 12821:2020
01-januar-2020
Nadomešča:
SIST EN ISO 12821:2015
Steklena embalaža - Kronsko grlo 26 H 180 - Mere (ISO 12821:2019)
Glass packaging - 26 H 180 crown finish - Dimensions (ISO 12821:2019)
Verpackungen aus Glas - Kronenmundstück 26 H 180 - Maße (ISO 12821:2019)
Emballage en verre - Bague couronne 26 H 180 - Dimensions (ISO 12821:2019)
Ta slovenski standard je istoveten z: EN ISO 12821:2019
ICS:
55.100 Steklenice. Lonci. Kozarci Bottles. Pots. Jars
SIST EN ISO 12821:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 12821:2020
---------------------- Page: 2 ----------------------
SIST EN ISO 12821:2020
EN ISO 12821
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2019
EUROPÄISCHE NORM
ICS 55.100 Supersedes EN ISO 12821:2015
English Version
Glass packaging - 26 H 180 crown finish - Dimensions (ISO
12821:2019)
Emballage en verre - Bague couronne 26 H 180 - Verpackungen aus Glas - Kronenmundstück 26 H 180 -
Dimensions (ISO 12821:2019) Maße (ISO 12821:2019)
This European Standard was approved by CEN on 20 July 2019.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 12821:2019 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 12821:2020
EN ISO 12821:2019 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 12821:2020
EN ISO 12821:2019 (E)
European foreword
This document (EN ISO 12821:2019) has been prepared by Technical Committee ISO/TC 63 "Glass
containers" in collaboration with Technical Committee CEN/TC 261 “Packaging” the secretariat of
which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2020, and conflicting national standards shall be
withdrawn at the latest by April 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 12821:2015.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 12821:2019 has been approved by CEN as EN ISO 12821:2019 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 12821:2020
---------------------- Page: 6 ----------------------
SIST EN ISO 12821:2020
INTERNATIONAL ISO
STANDARD 12821
Second edition
2019-10
Glass packaging — 26 H 180 crown
finish — Dimensions
Emballage en verre — Bague couronne 26 H 180 — Dimensions
Reference number
ISO 12821:2019(E)
©
ISO 2019
---------------------- Page: 7 ----------------------
SIST EN ISO 12821:2020
ISO 12821:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 12821:2020
ISO 12821:2019(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions . 1
Bibliography . 6
© ISO 2019 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 12821:2020
ISO 12821:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The wo
...
SLOVENSKI STANDARD
oSIST prEN ISO 12821:2018
01-julij-2018
Steklena embalaža - Kronsko grlo 26 H 180 - Mere (ISO/DIS 12821:2018)
Glass packaging - 26 H 180 crown finish - Dimensions (ISO/DIS 12821:2018)
Verpackungen aus Glas - Kronenmundstück 26 H 180 - Maße (ISO/DIS 12821:2018)
Emballage en verre - Bague couronne 26 H 180 - Dimensions (ISO/DIS 12821:2018)
Ta slovenski standard je istoveten z: prEN ISO 12821
ICS:
55.100 Steklenice. Lonci. Kozarci Bottles. Pots. Jars
oSIST prEN ISO 12821:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 12821:2018
---------------------- Page: 2 ----------------------
oSIST prEN ISO 12821:2018
DRAFT INTERNATIONAL STANDARD
ISO/DIS 12821
ISO/TC 63 Secretariat: BSI
Voting begins on: Voting terminates on:
2018-05-31 2018-08-23
Glass packaging — 26 H 180 crown finish — Dimensions
Emballage en verre — Bague couronne 26 H 180 — Dimensions
ICS: 55.100
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 12821:2018(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2018
---------------------- Page: 3 ----------------------
oSIST prEN ISO 12821:2018
ISO/DIS 12821:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 12821:2018
ISO/DIS 12821:2018(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Dimensions . 1
Bibliography . 6
© ISO 2018 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 12821:2018
ISO/DIS 12821:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying an
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.