SIST EN ISO 11126-8:2018

Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 8: Olivine (ISO 11126-8:2018)

This document specifies requirements for olivine abrasives, as supplied for blast-cleaning processes.
It specifies ranges of particle sizes and values for apparent density, Mohs hardness, moisture content,
conductivity of aqueous extract and water-soluble chlorides.
The requirements specified in this document apply to abrasives supplied in the "new" condition only.
They do not apply to abrasives either during or after use.
Test methods for non-metallic blast-cleaning abrasives are given in the various parts of ISO 11127.
NOTE Although this document has been developed specifically to meet requirements for preparation of
steelwork, the properties specified will generally be appropriate for use when preparing other material surfaces,
or components, using blast-cleaning techniques. These techniques are described in ISO 8504-2.

Vorbereitung von Stahloberflächen vor dem Auftragen von Beschichtungsstoffen - Anforderungen an nichtmetallische Strahlmittel - Teil 8: Olivinsand (ISO 11126-8:2018)

Préparation des subjectiles d'acier avant application de peintures et de produits assimilés - Spécifications pour abrasifs non métalliques destinés à la préparation par projection - Partie 8: Olivine (ISO 11126-8:2018)

Le présent document spécifie les exigences relatives aux abrasifs en olivine tels que commercialisés pour les processus de décapage à l'abrasif. Il spécifie les plages granulométriques et les valeurs de la masse volumique apparente, la dureté selon l'échelle de Mohs, la teneur en humidité, la conductivité de l'extrait aqueux et la teneur en chlorures solubles dans l'eau.
Les exigences spécifiées dans le présent document s'appliquent seulement aux abrasifs fournis à l'état « neuf ». Elles ne s'appliquent pas aux abrasifs pendant ou après utilisation.
Des méthodes d'essai des abrasifs non métalliques pour décapage par projection sont données dans les différentes parties de l'ISO 11127.
NOTE       Bien que le présent document ait été spécifiquement élaboré pour satisfaire aux exigences de préparation d'ouvrages en acier, les propriétés spécifiées conviennent de manière générale pour une utilisation dans la préparation d'autres surfaces de matériaux ou d'autres composants par des techniques de décapage à l'abrasif. Ces techniques sont décrites dans l'ISO 8504‑2.

Priprava jeklenih podlag pred nanašanjem barv in sorodnih premazov - Specifikacije za nekovinske granulate za peskanje - 8. del: Olivinski pesek (ISO 11126-8:2018)

Ta dokument določa zahteve za granulate v obliki olivinskega peska, dobavljene za peskanje. Določa razpon velikosti delcev in vrednosti za navidezno gostoto, Mohsovo trdoto, vsebnost vlage, prevodnost vodnega ekstrakta in vodotopnih kloridov.
Zahteve v tem dokumentu se uporabljajo samo za granulate, ki so dobavljeni »novi«.
Ne uporabljajo se za granulate med njihovo uporabo ali po njej.
Preskusne metode za nekovinske granulate za peskanje so podane v različnih delih standarda ISO 11127.
OPOMBA: Čeprav je bil ta dokument pripravljen posebej za izpolnjevanje zahtev za pripravo jekla, so opredeljene lastnosti na splošno ustrezne za uporabo pri obdelavi površin drugih materialov ali sestavnih delov s tehnikami peskanja. Te tehnike so opisane v standardu ISO 8504-2.

General Information

• Status: Published
• Public Enquiry End Date: 21-Dec-2017
• Publication Date: 06-Nov-2018
• ICS: 25.220.10 - Surface preparation
• ICS: 87.020 - Paint coating processes
• Technical Committee: IBLP - Paints and varnishes
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 10-Oct-2018
• Due Date: 15-Dec-2018
• Completion Date: 07-Nov-2018
• Ref Project: EN ISO 11126-8:2018 - Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 8: Olivine (ISO 11126-8:2018, Corrected version 2018-11)

Relations

• Replaces: SIST EN ISO 11126-8:1997 - Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 8: Olivine sand (ISO 11126-8:1993)
• Effective Date: 01-Dec-2018
• Replaces: SIST EN ISO 11126-8:1997 - Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 8: Olivine sand (ISO 11126-8:1993)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 11126-8:2018
01-december-2018
1DGRPHãþD
SIST EN ISO 11126-8:1997
Priprava jeklenih podlag pred nanašanjem barv in sorodnih premazov -
Specifikacije za nekovinske granulate za peskanje - 8. del: Olivinski pesek (ISO
11126-8:2018)
Preparation of steel substrates before application of paints and related products -
Specifications for non-metallic blast-cleaning abrasives - Part 8: Olivine (ISO 11126-
8:2018)
Vorbereitung von Stahloberflächen vor dem Auftragen von Beschichtungsstoffen -
Anforderungen an nichtmetallische Strahlmittel - Teil 8: Olivinsand (ISO 11126-8:2018)
Préparation des subjectiles d'acier avant application de peintures et de produits
assimilés - Spécifications pour abrasifs non métalliques destinés à la préparation par
projection - Partie 8: Olivine (ISO 11126-8:2018)
Ta slovenski standard je istoveten z: EN ISO 11126-8:2018
ICS:
25.220.10 Priprava površine Surface preparation
87.020 Postopki za nanašanje Paint coating processes
barvnih premazov
SIST EN ISO 11126-8:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 11126-8:2018

---------------------- Page: 2 ----------------------

SIST EN ISO 11126-8:2018


EN ISO 11126-8
EUROPEAN STANDARD

NORME EUROPÉENNE

October 2018
EUROPÄISCHE NORM
ICS 25.220.10 Supersedes EN ISO 11126-8:1997
English Version

Preparation of steel substrates before application of paints
and related products - Specifications for non-metallic
blast-cleaning abrasives - Part 8: Olivine (ISO 11126-
8:2018)
Préparation des subjectiles d'acier avant application de Vorbereitung von Stahloberflächen vor dem Auftragen
peintures et de produits assimilés - Spécifications pour von Beschichtungsstoffen - Anforderungen an
abrasifs non métalliques destinés à la préparation par nichtmetallische Strahlmittel - Teil 8: Olivinsand (ISO
projection - Partie 8: Olivine (ISO 11126-8:2018) 11126-8:2018)
This European Standard was approved by CEN on 12 August 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11126-8:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 11126-8:2018
EN ISO 11126-8:2018 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 11126-8:2018
EN ISO 11126-8:2018 (E)
European foreword
This document (EN ISO 11126-8:2018) has been prepared by Technical Committee ISO/TC 35 "Paints
and varnishes" in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2019, and conflicting national standards shall be
withdrawn at the latest by April 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11126-8:1997.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11126-8:2018 has been approved by CEN as EN ISO 11126-8:2018 without any
modification.


3

---------------------- Page: 5 ----------------------

SIST EN ISO 11126-8:2018

---------------------- Page: 6 ----------------------

SIST EN ISO 11126-8:2018
INTERNATIONAL ISO
STANDARD 11126-8
Second edition
2018-08
Preparation of steel substrates before
application of paints and related
products — Specifications for non-
metallic blast-cleaning abrasives —
Part 8:
Olivine
Préparation des subjectiles d'acier avant application de peintures et
de produits assimilés — Spécifications pour abrasifs non métalliques
destinés à la préparation par projection —
Partie 8: Olivine
Reference number
ISO 11126-8:2018(E)
©
ISO 2018

---------------------- Page: 7 ----------------------

SIST EN ISO 11126-8:2018
ISO 11126-8:2018(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 11126-8:2018
ISO 11126-8:2018(E)

Contents Page
Foreword .iv
1 Scope . 1
2  Normative references . 1
3  Terms and definitions . 2
4  Designation of abrasives . 2
5  Sampling . 2
6 Requirements . 3
6.1 General requirements . 3
6.2 Particular requirements . 3
7  Identification and marking. 3
8  Information to be supplied by the manufacturer or supplier . 3
Bibliography . 4
© ISO 2018 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 11126-8:2018
ISO 11126-8:2018(E)

Foreword
ISO (the International Organization for Standardization) is a wo
...