SIST EN ISO 24343-1:2012
(Main)Resilient and laminate floor coverings - Determination of indentation and residual indentation - Part 1: Residual indentation (ISO 24343-1:2007)
Resilient and laminate floor coverings - Determination of indentation and residual indentation - Part 1: Residual indentation (ISO 24343-1:2007)
This International Standard describes a method for determining the residual indentation produced in a resilient or laminate floor covering after the application and removal of a constant load.
Elastische und Laminat-Bodenbeläge - Bestimmung des Eindrucks und des Resteindrucks - Teil 1: Resteindruck (ISO 24343-1:2007)
Der vorliegende Teil der ISO 24343 beschreibt ein Verfahren zur Bestimmung des Resteindruckes in einem elastischen oder Laminat Bodenbelag nach dem Be und Entlasten mit einer konstanten Last.
Revêtements de sol résilients et stratifiés - Détermination du poinçonnement et du poinçonnement rémanent - Partie 1: Poinçonnement rémanent (ISO 24343-1:2007)
Netekstilne in laminatne talne obloge - Ugotavljanje vtiska in preostalega vtiska - 1. del: Preostali vtisk (ISO 24343-1:2007)
Ta del standarda ISO 24343 opisuje metodo za ugotavljanje preostalega vtiska, ki nastane na netekstilnih in laminatnih talnih oblogah po namestitvi in odstranitvi stalnega bremena.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 24343-1:2012
01-marec-2012
1DGRPHãþD
SIST EN 433:1999
Netekstilne in laminatne talne obloge - Ugotavljanje vtiska in preostalega vtiska -
1. del: Preostali vtisk (ISO 24343-1:2007)
Resilient and laminate floor coverings - Determination of indentation and residual
indentation - Part 1: Residual indentation (ISO 24343-1:2007)
Elastische und Laminat-Bodenbeläge - Bestimmung des Eindrucks und des
Resteindrucks - Teil 1: Resteindruck (ISO 24343-1:2007)
Revêtements de sol résilients et stratifiés - Détermination du poinçonnement et du
poinçonnement rémanent - Partie 1: Poinçonnement rémanent (ISO 24343-1:2007)
Ta slovenski standard je istoveten z: EN ISO 24343-1:2012
ICS:
97.150 Netekstilne talne obloge Non-textile floor coverings
SIST EN ISO 24343-1:2012 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 24343-1:2012
---------------------- Page: 2 ----------------------
SIST EN ISO 24343-1:2012
EUROPEAN STANDARD
EN ISO 24343-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2012
ICS 97.150 Supersedes EN 433:1994
English Version
Resilient and laminate floor coverings - Determination of
indentation and residual indentation - Part 1: Residual
indentation (ISO 24343-1:2007)
Revêtements de sol résilients et stratifiés - Détermination Elastische und Laminat-Bodenbeläge - Bestimmung des
du poinçonnement et du poinçonnement rémanent - Partie Eindrucks und des Resteindrucks - Teil 1: Resteindruck
1: Poinçonnement rémanent (ISO 24343-1:2007) (ISO 24343-1:2007)
This European Standard was approved by CEN on 17 December 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 24343-1:2012: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 24343-1:2012
EN ISO 24343-1:2012 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 24343-1:2012
EN ISO 24343-1:2012 (E)
Foreword
The text of ISO 24343-1:2007 has been prepared by Technical Committee ISO/TC 219 “Floor coverings” of
the International Organization for Standardization (ISO) and has been taken over as EN ISO 24343-1:2012 by
Technical Committee CEN/TC 134 “Resilient, textile and laminate floor coverings” the secretariat of which is
held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by July 2012, and conflicting national standards shall be withdrawn at the
latest by July 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 433:1994.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 24343-1:2007 has been approved by CEN as a EN ISO 24343-1:2012 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 24343-1:2012
---------------------- Page: 6 ----------------------
SIST EN ISO 24343-1:2012
INTERNATIONAL ISO
STANDARD 24343-1
First edition
2007-06-15
Resilient and laminate floor coverings —
Determination of indentation and residual
indentation —
Part 1:
Residual indentation
Revêtements de sol résilients et stratifiés — Détermination du
poinçonnement et du poinçonnement rémanent —
Partie 1: Poinçonnement rémanent
Reference number
ISO 24343-1:2007(E)
©
ISO 2007
---------------------- Page: 7 ----------------------
SIST EN ISO 24343-1:2012
ISO 24343-1:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2007
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2007 – All rights reserved
---------------------- Page: 8 ---------------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.