SIST EN 61169-14:2011

Radio-frequency connectors - Part 14: R.F. coaxial connectors with inner diameter of outer conductor 12 mm with screw coupling - Characteristic impedance 75 ohms (Type 3.5/12) (IEC 61169-14:2010)

This standard concerns RF coaxial connectors for use with RF cables both flexible and semirigid, where air dielectric interface and high mechanical stability is required for severe environmental exposure. The connectors provide low reflection in the microwave region up to 12 GHz and all patterns may provide sealing up to a pressure differential of 3 bar. For this type of connector, cables IEC 75-7-and 75-8 of IEC 61196-6: Coaxial communication cables – Part 6: Sectional specification for CATV drop cables, are recommended. This type is known commercially as the 3,5/12 connector.

Hochfrequenz-Steckverbinder - Teil 14: Koaxiale HF-Steckverbinder mit 12 mm Innendurchmesser des Außenleiters mit Schraubverbindung - Wellenwiderstand 75 Ohm (Typ 3,5/12) (IEC 61169-14:2010)

Connecteurs pour fréquences radioélectriques - Partie 14: Connecteurs coaxiaux pour fréquences de diamètre intérieur du conducteur extérieur de 12 mm à verrouillage à vis -- Impédance caractéristique 75 ohms (Type 3,5/12) (CEI 61169-14:2010)

La CEI 61169-14:2010 concerne les connecteurs coaxiaux pour fréquences radioélectriques pouvant être utilisés avec des câbles pour fréquences radioélectriques, soit souples, soit semi-rigides, avec interface à diélectrique air et où une haute stabilité mécanique est exigée pour des conditions d'environnement sévères. Les connecteurs ont un bas coefficient de réflexion dans le domaine des micro-ondes allant jusqu'à 12 GHz et tous les modèles peuvent être étanches jusqu'à une pression différentielle de 3 bar. La version française de cette norme n'a pas été soumise au vote.

Radiofrekvenčni konektorji - 14. del: Radiofrekvenčni (RF) koaksialni konektorji z notranjim premerom zunanjega vodnika 12 mm in navojnim spajanjem - Karakteristična impedanca 75 ohmov (tip 3.5/12) (IEC 61169-14:2010)

Ta standard obravnava RF koaksialne konektorje, tako prilagodljive kot poltrde, kjer se zahteva radijski izolacijski vmesnik in visoka mehanska stabilnost pri hudi izpostavljenosti okolju. Ti konektorji zagotavljajo nizek odboj na področju mikrovalov do 12 GHz, vsi vzorci pa lahko zagotavljajo tesnjenje do razlike v tlaku 3 barov. Za ta tip konektorja se priporočajo kabli IEC 75-7 in 75-8 iz IEC 61196-6: Koaksialni komunikacijski kabli – 6. del: Področna specifikacija za zaključne kable za kabelsko televizijo se priporoča. Ta tip je poznan na tržišču kot 3,5/12 konektor.

General Information

• Status: Published
• Publication Date: 16-Dec-2010
• ICS: 33.120.30 - RF connectors
• Technical Committee: iTEL - Communication cables
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 15-Dec-2010
• Due Date: 19-Feb-2011
• Completion Date: 17-Dec-2010
• Ref Project: EN 61169-14:2010 - Radio-frequency connectors - Part 14: R.F. coaxial connectors with inner diameter of outer conductor 12 mm with screw coupling - Characteristic impedance 75 ohms (Type 3,5/12)

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61169-14:2011
01-januar-2011
5DGLRIUHNYHQþQLNRQHNWRUMLGHO5DGLRIUHNYHQþQL5)NRDNVLDOQLNRQHNWRUML]
QRWUDQMLPSUHPHURP]XQDQMHJDYRGQLNDPPLQQDYRMQLPVSDMDQMHP
.DUDNWHULVWLþQDLPSHGDQFDRKPRYWLS,(&
Radio-frequency connectors - Part 14: R.F. coaxial connectors with inner diameter of
outer conductor 12 mm with screw coupling - Characteristic impedance 75 ohms (Type
3.5/12) (IEC 61169-14:2010)
Hochfrequenz-Steckverbinder - Teil 14: Koaxiale HF-Steckverbinder mit 12 mm
Innendurchmesser des Außenleiters mit Schraubverbindung - Wellenwiderstand 75 Ohm
(Typ 3,5/12) (IEC 61169-14:2010)
Connecteurs pour fréquences radioélectriques - Partie 14: Connecteurs coaxiaux pour
fréquences de diamètre intérieur du conducteur extérieur de 12 mm à verrouillage à vis -
- Impédance caractéristique 75 ohms (Type 3,5/12) (CEI 61169-14:2010)
Ta slovenski standard je istoveten z: EN 61169-14:2010
ICS:
33.120.30 5DGLRIUHNYHQþQLNRQHNWRUML R.F. connectors
5)
SIST EN 61169-14:2011 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61169-14:2011

---------------------- Page: 2 ----------------------

SIST EN 61169-14:2011

EUROPEAN STANDARD
EN 61169-14

NORME EUROPÉENNE
December 2010
EUROPÄISCHE NORM

ICS 33.120.30


English version


Radio-frequency connectors -
Part 14: R.F. coaxial connectors with inner diameter of outer conductor 12
mm with screw coupling -
Characteristic impedance 75 ohms (Type 3,5/12)
(IEC 61169-14:2010)


Connecteurs pour fréquences Hochfrequenz-Steckverbinder -
radioélectriques - Teil 14: Koaxiale HF-Steckverbinder mit
Partie 14: Connecteurs coaxiaux pour 12 mm Innendurchmesser des
fréquences de diamètre intérieur du Außenleiters mit Schraubverbindung -
conducteur extérieur de 12 mm à Wellenwiderstand 75 Ohm (Typ 3,5/12)
verrouillage à vis - (IEC 61169-14:2010)
Impédance caractéristique 75 ohms (Type
3,5/12)
(CEI 61169-14:2010)



This European Standard was approved by CENELEC on 2010-12-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61169-14:2010 E

---------------------- Page: 3 ----------------------

SIST EN 61169-14:2011
EN 61169-14:2010 - 2 -
Foreword
The text of document 46F/148/CDV, future edition 1 of IEC 61169-14, prepared by IEC/SC 46F, R.F. and
microwave passive components, of IEC TC 46, Cables, wires, waveguides, R.F. connectors, R.F. and
microwave passive components and accessories, was submitted to the IEC-CENELEC parallel vote and
was approved by CENELEC as EN 61169-14 on 2010-12-01.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2011-09-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2013-12-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61169-14:2010 was approved by CENELEC as a European
Standard without any modification.
__________

---------------------- Page: 4 ----------------------

SIST EN 61169-14:2011
- 3 - EN 61169-14:2010
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

IEC 61169-1 1992 Radio-frequency connectors - EN 61169-1 1994
+ A1 1996 Part 1: Generic specification - General + A1 1996
+ A2 1997 requirements and measuring methods + A2 1997

---------------------- Page: 5 ----------------------

SIST EN 61169-14:2011

---------------------- Page: 6 ----------------------

SIST EN 61169-14:2011

IEC 61169-14
®
Edition 1.0 2010-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside


Radio-frequency connectors –
Part 14: R.F. coaxial connectors with inner diameter of outer conductor 12 mm
with screw coupling – Characteristic impedance 75 ohms (Type 3,5/12)

Connecteurs pour fréquences radioélectriques –
Partie 14: Connecteurs coaxiaux pour fréquences de diamètre intérieur du
conducteur extérieur de 12 mm à verrouillage à vis – Impédance caractéristique
75 ohms (Type 3,5/12)

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
U
CODE PRIX
ICS 33.120.30 ISBN 978-2-88912-161-8
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 61169-14:2011
– 2 – 61169-14 © IEC:2010
CONTENTS
FOREWORD.4
1 Scope.6
2 Normative references .6
3 IEC type designation .6
4 Mating face for general purpose connector .7
4.1 Connector with pin centre contact.7
(see Figure 1).7
4.2 Connector with socket centre contact .8
(see Figure 2).8
5 Gauges and standard test connectors .9
5.1 Mechanical gauges.9
5.1.1 Socket connector.9
5.2 Standard test connectors (Grade 0).9
5.2.1 General .9
5.2.2 Standard test connectors with pin centre contact .9
5.2.3 Standard test connectors with socket centre contact.10
6 Survey of patterns .10
7 Outline dimensions.12
8 Quality assessment procedures.16
8.1 General .16
8.2 Ratings and characteristics .16
8.3 Test schedule and inspection requirements .18
8.3.1 Acceptance tests .18
8.3.2 Periodic tests .19
8.4 Procedures.20
8.4.1 Quality conformance inspection .20
8.4.2 Qualification approval and its maintenance.20
9 Instructions for preparation of detail specifications .21
9.1 General .21
9.2 Identification of the detail specification .22
9.3 Identification of the component.22
9.4 Performance.22
9.5 Marking, ordering information and related matters .22
9.6 Selection of tests, test conditions and severities.22
10 Blank detail specification pro-forma for type 3.5/12 connector .24

7
Figure 1 – Connector with pin centre contact (for dimensions, see Table 1) .
Figure 2 – Connector with socket centre contact (for dimensions, see Table 2).8
Figure 3 – Gauge pins for centre contact of socket connector .9
Figure 4 – Slotted centre contact .10

Table 1 – Dimensions for connector with pin centre contact .7
Table 2 – Dimensions for connector with socket centre contact.8
Table 3 – Dimensions for connector with pin centre contact Grade 0 .9

---------------------- Page: 8 ----------------------

SIST EN 61169-14:2011
61169-14 © IEC:2010 – 3 –
Table 4 – Dimensions for connector with socket centre contact Grade 0 .10
Table 5 – Survey of patterns .10
Table 6 – Outline dimensions.13
Table 7 – Rating and characteristic.16
Table 8 – Acceptance tests.18
Table 9 – Periodic tests .19

---------------------- Page: 9 ----------------------

SIST EN 61169-14:2011
– 4 – 61169-14 © IEC:2010
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

RADIO-FREQUENCY CONNECTORS –

Part 14: R.F. coaxial connectors with inner diameter
of outer conductor 12 mm with screw coupling –
Characteristic impedance 75 ohms (Type 3,5/12)


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61169-14 has been prepared by subcommittee 46F: RF and
microwave passive components, of IEC technical committee 46: Cables, wires, waveguides,
R.F. connectors, R.F. and microwave passive components and accessories.
This first edition cancels and replaces IEC 60169-14 published in 1977. This edition constitutes a
technical revision.
The text of this standard is based on the following documents:
FDIS Report on voting
46F/148/CDV 46F/169/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.

---------------------- Page: 10 ----------------------

SIST EN 61169-14:2011
61169-14 © IEC:2010 – 5 –
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of the IEC 61169 series, under the general title: Radio-frequency connectors,
can be found on the IEC website.
A bilingual version may be issued at a later date.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.

---------------------- Page: 11 ----------------------

SIST EN 61169-14:2011
– 6 – 61169-14 © IEC:2010
RADIO-FREQUENCY CONNECTORS –

Part 14: R.F. coaxial connectors with inner diameter
of outer conductor 12 mm with screw coupling –
Characteristic impedance 75 ohms (Type 3,5/12)

1 Scope
This standard concerns RF coaxial connectors for use with RF cables both flexible and semi-
rigid, where air dielectric interface and high mechanical stability is required for severe
environmental exposure. The connectors provide low reflection in the microwave region up to
12 GHz and all patterns may provide sealing up to a pressure differential of 3 bar.
For this type of connector, cables IEC 75-7-and 75-8 of IEC 61196-6: Coaxial communication
cables – Part 6: Sectional specification for CATV drop cables, are recommended.
This type is known commercially as the 3,5/12 connector.
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 61169-1:1992, Radio-frequency connectors – Part 1: Generic specification – General
1
requirements and measuring methods
Amendment 1 (1996)
Amendment 2 (1997)
3 IEC type designation
Connectors conforming to this standard shall be designated by:
a) the reference to this standard: 61169-14 IEC;
b) number of the grade:
Grade 0 = standard test connector = G0
Grade 1 = high performance connector = G1
Grade 2 = general purpose connector
– if Grade 2 is required, no grade designation is necessary;
c) a serial number (see Clause 7);
d) a group of figures specifying the climatic category (see Clause 4).
Example
61169-14 IEC-Gl-1 (40/85/21) denotes a free pin Grade 1 high performance connector
(straight) for cable 96-2 IEC 75-7-1/2/8 with mating face as indicated in Clause 5 of this
standard with a reflection coefficient not greater than 0,06 at frequencies up to 6 GHz
belonging to climatic category 40/85/21.
___________
1
There exists a consolidated edition 1.2 (1998) that comprises IEC 61169-1:1992, its Amendment 1:1996 and its
Amendment 2:1997.

---------------------- Page: 12 ----------------------

SIST EN 61169-14:2011
61169-14 © IEC:2010 – 7 –
4 Mating face for general purpose connector
4.1 Connector with pin centre contact
(see Figure 1)
k
h
i
a b c d e
g
Note 4
f
IEC  1983/10

Figure 1 – Connector with pin centre contact
(for dimensions, see Table 1)
Table 1 – Dimensions for connector with pin centre contact
Ref. mm Note
Min. Max.

a 2
M 20 × 1
b 14,84 14,95
c 2,855 2,945
d 3,5 ref 1/3
e 1/3
12,0 ref
f 2,51 2,7 6
g 1,8 –
h 7 9
i 2,2 2,7
k 8 – 5
NOTE 1 The tolerance on this dimension is determined by the tolerance of characteristic
impedance. (For Grade 1 connector, the characteristic impedance should be 75 Ω ± 0,38 Ω).
NOTE 2 M 20 × 1 indicates metric ISO screw-thread with nominal diameter 20 mm and
pitch 1 mm.
NOTE 3 Reference dimensions.
NOTE 4 Mechanical and electrical reference plane.
NOTE 5 This dimension together with O-ring gasket to meet environmental requirements.
NOTE 6 For Grade 1 connectors: dimension f: 2,51 mm min.
                                          2,6 mm max.
NOTE 7 All undimensioned pictorial configurations are for reference purposes only.

---------------------- Page: 13 ----------------------

SIST EN 61169-14:2011
– 8 – 61169-14 © IEC:2010
4.2 Connector with socket centre contact
(see Figure 2)

s
u d n ma
p
q
Note 5
r
Note 4
t
IEC  1984/10

Figure 2 – Connector with socket centre contact
(for dimensions, see Table 2)
Table 2 – Dimensions for connector with socket centre contact
Ref. mm Note
Min. Max.
a 2
M 20 × 1
d 3,5 ref. 1/3

m 15,5 16,0
n 15,0 15,1
p 2,3 2,49 6
q 6,9 7,1
r 9,0 11
s 4,5 –

t 15,5 –
u 19,7 20,2
NOTE 1 The tolerance on this dimension is determined by the tolerance of characteristic
impedance. (For Grade 1 connector the characteristic impedance should be 75 Ω ±
0,38 Ω).
NOTE 2 M 20 × 1 indicates metric ISO screw-thread with nominal diameter 20 mm and
pitch 1 mm.
NOTE 3 Reference dimension.
NOTE 4 Mechanical and electrical reference plane.
NOTE 5 Bore diameter and slots to meet gauge requirements.
NOTE 6 For Grade 1 connectors:
dimension p: 2,4 mm min.
 2,49 mm max.
NOTE 7 All undimensioned pictorial configurations are for reference purposes only.

---------------------- Page: 14 ----------------------

SIST EN 61169-14:2011
61169-14 © IEC:2010 – 9 –
5 Gauges and standard test connectors
5.1 Mechanical gauges
5.1.1 Socket connector
5.1.1.1 Centre contact

∼50°
a
3,5
2
IEC  1985/10

Figure 3 – Gauge pins for centre contact of socket connector
5.1.1.2 Test sequence
a) A steel test pin (Figure 3) with a diameter a of 3,1 mm ± 0,005 mm shall be inserted once
into the centre contact a minimum distance of 2 mm.
b) A second steel test pin (Figure 3) with a diameter a of 2,855 mm ± 0,005 mm and a 0,4 μm
finish shall then be inserted. The contact shall then exert a retention force of 4 N
minimum/9 N maximum after insertion into the centre contact.
It is recommended that the mass of this gauge should be 400 g.
5.2 Standard test connectors (Grade 0)
5.2.1 General
In order to carry out the reflection coefficient measurement according to Subclause 14.1 of
IEC 61169-1, the measuring equipment should be provided with standard test connectors
(Grade 0). The standard test connectors with tolerances specified in 5.2.2 and 5.2.3
guarantee an accuracy of characteristic impedance of 75 Ω ± 0,1 Ω.
5.2.2 Standard test connectors with pin centre contact
The dimensions of the standard test connectors with pin centre contact shall be as specified
in Subclause 5.1 but with the following tolerances (see Table 3).

Table 3 – Dimensions for connector with pin centre contact Grade 0
mm
Dimension
Min. Max.
c 2,898 2,902
d 3,482 3,485
e 12,165 12,185
f 2,51 2,53

---------------------- Page: 15 ----------------------

SIST EN 61169-14:2011
– 10 – 61169-14 © IEC:2010
5.2.3 Standard test connectors with socket centre contact
The dimensions of the standard test connectors with socket centre contact shall be as
specified in 5.2 and with the following tolerances (see Table 4).
Table 4 – Dimensions for connector with socket centre contact Grade 0
mm
Dimension
Min. Max.
d 3,482 3,485
e 12,165 12,185
p 2,47 2,49

Additionally, dimensions of the slotted centre contact (see Figure 4) shall be as follows:
Key
y = ∅ 3,483 mm min.
∅ 3,485 mm max.

with pin gauge ∅ 2,898 mm min.
 ∅ 2,902 mm max.
w v
y
inserted 2 mm deep
x
w = to fulfil the requirements of dimension y and
IEC  1986/10

gauge retention
x = six slots spaced 60° apart

0,3 mm wide
4,5 mm min. length
4,7 mm) max. length
y = radius of chamfer r = 0,1 mm
Figure 4 – Slotted centre contact
A pair of standard test connectors shall not introduce a reflection coefficient greater than 0,01
at 6 GHz.
6 Survey of patterns
Table 5 is a survey of existing patterns.
Table 5 – Survey of patterns
Test Type
Description Contact Pattern
1
class designation
1 Free connector (straight) Pin 61169-14 IEC-1

See Note
IEC  1987/10

---------------------- Page: 16 ----------------------

SIST EN 61169-14:2011
61169-14 © IEC:2010 – 11 –
Test Type
Description Contact Pattern 1
class designation
1 Free connector (right angle) Pin 61169-14 IEC-2

See Note
IEC  1987/10

1 Free connector (straight) Socket 61169-14 IEC-3

See Note
IEC  1988/10

1 Fixed connector (straight Socket 61169-14 IEC-4

4-hole panel mounting with See Note
entry for r.f. cable)
IEC  1989/10

1 Fixed connector (right Socket 61169-14 IEC-5

angle), 4-hole panel See Note
mounting with entry for r.f.
cable)
IEC  1990/10

3 Fixed connector Socket 61169-14 IEC-6

(4-hole panel mounting with
solder bucket)
IEC  1991/10

3 Fixed connector (panel and Socket 61169-14 IEC-7

barrier sealed, single hole
panel mounting with solder
bucket)
IEC  1992/10

2 Free adaptor (right angle) Pin- 61169-14 IEC-8

socket
IEC  1993/10

2 Fixed adaptor Socket- 61169-14 IEC-9

(panel and barrier sealed, socket
single hole panel mounting)
IEC  1994/10

2 Fixed adaptor Socket- 61169-14 IEC-10

(4-hole panel mounting) socket
IEC  1995/10

2 Fixed connector Socket 61169-14 IEC-11

(4-hole panel mounting for
rigid lines)
IEC  1996/10

---------------------- Page: 17 ----------------------

SIST EN 61169-14:2011
– 12 – 61169-14 © IEC:2010
Test Type
Description Contact Pattern 1
class designation
2 Free adaptor Socket- 61169-14 IEC-12

socket
IEC  1997/10

3 T-adaptor Pin- 61169-14 IEC-13

socket-
socket
IEC  1998/10

1
 If no details are given, Grade 2 is referred to. Grade 1 has to be indicated.
NOTE To be used with r.f: cables 61196-6 IEC 75-7 or 8.
In Table 5, the test classes applicable to the various connector patterns are indicated.
A test class comprises all connectors to which the same tests are applicable although in some
cases the test requirements may differ in part.
Test Class 1: Connectors attached to cables.
Test Class 2: Adaptors with mating faces at both ends.
Test Class 3: Connectors to which the reflection coefficient measurements do not apply.
7 Outline dimensions
The appearance of the connectors shown in the following Table 6 drawings is typical. Only the
main dimensions given are mandatory (dimensions in millimetres).
Other constructions or the use of other cables are permissible if the dimensions according to
Clause 5 are met, together with the gauging requirements of Clause 6 and applicable test
conditions of Clause 9.
The type designation refers to Grade 2 (for Grade 1 and 0, see Clause 2).

---------------------- Page: 18 ----------------------

SIST EN 61169-14:2011
61169-14 © IEC:2010 – 13 –
Table 6 – Outline dimensions
Test
Style Type
Class
designation
61169-14
Free connector 1
Width across
Space for
IEC1-
(straight) with pin
flats 22
marking
contact
66 max.
IEC  1999/10

Free connector 1 61169-14
28 max.
(right angle) with IEC-2
pin contact
Space for
marking
IEC  2000/10

Free connector 1 61169-14
Space for
(straight) with
IEC-3
marking
socket con
65 max.
IEC  2001/10

Fixed connector 1 61169-14

(straight, 4-hole Space for IEC-4
M3
panel mounting
marking
with entry for r.f.
cable) with
socket contact
2,5
15,5 19
25,4
65 max.
IEC  2002/10

Fixed connector 36 max. 1 61169-14
25,4
(right angle, 4- IEC-5
15,5
19
hole panel 2,5
mounting with
entry for r.f.
cable) with
socket contact
Space for
marking
IEC  2003/10

39 max.
∅25 max.
∅25 max.
∅20
∅20
25,4
19
39 max.
∅20
M3
19
25,4

---------------------- Page: 19 ----------------------

SIST EN 61169-14:2011
– 14 – 61169-14 © IEC:2010
Test
Style Type
Class
designation
Fixed connector 3 61169-14

Space for
M3
(4-hole panel
IEC-6
marking
mounting with
solder bucket)
with socket
contact
19
15,5
25,4
20 max.
IEC  2004/10

Fixed connector 3 61169-14

Space for
(panel and IEC-7
marking
barrier sealed,
single hole panel
mounting
with solder
bucket) with
socket contact
0
16
17
Internal
–2
22 max.
construction
20
not shown
27
IEC  2005/10

Free adaptor 2 61169-14

(right angle) with IEC-8
28 max.
Space for
pin-socket
marking
contact
∅20
IEC  2006/10

Fixed adaptor 2 61169-14
Internal
Width across
(panel and IEC-9
construction
flats 27
barrier sealed,
not shown
single hole panel
mounting)
with socket-
Space for
socket contacts
marking
0
17
Optional
2,5
–2
15,5
20
40 max.
31
IEC  2007/10

∅20
∅25 max.
31
34 max.
19
25,4

---------------------- Page: 20 ----------------------

SIST EN 61169-14:2011
61169-14 © IEC:2010 – 15 –
Test
Style Type
Class
designation
Fixed adaptor (4- 2 61169-14

hole panel IEC-10
mounting) Space for
35 optional
with socket- marking
socket contacts
 5
15,5
35
45 m
...