SIST EN 13379:2002/kFprA1:2012
(Amendment)Pasta processing plants - Spreader, stripping and cutting machine, stick return conveyor, stick magazine - Safety and hygiene requirements
Pasta processing plants - Spreader, stripping and cutting machine, stick return conveyor, stick magazine - Safety and hygiene requirements
This European Standard applies to spreader, stripping and cutting machine, as well as the stick return conveyor and the stick magazine (see clause 3), used in continuous pasta processing plants able to produce more than 100 kg/h.
This European Standard specifies the safety requirements for the design, manufacture and information for safe use of spreader, stripping and cutting machine, as well as the stick return conveyor and the stick magazine classified as stationary units which cannot be moved when in operation.
This draft European Standard does not apply to:
- household machines,
- semi-automatic machines, so called "batch machines" requiring manual loading.
The significant hazards covered by this standard are listed in clause 4.
These hazards and the measures for their reduction are described in the present European Standard.
Ancillary equipment, which is not an integral part of the machinery (e.g. hoppers), is not covered by this European Standard.
This European Standard is not applicable to machines in its scope which are manufactured before the date of its publication as EN.
Maschinen zur Teigwarenherstellung - Behänger, Abstreif- und Schneidmaschinen, Stabrücktransporte, Stabmagazine - Sicherheits- und Hygieneanforderungen
Machines pour pâtes alimentaires - Etendeuse, dégarnisseuse-découpeuse, convoyeur de retour des cannes et accumulateur de cannes - Prescriptions de sécurité et d'hygiène
Stroji za izdelavo testenin - Stroji za razvlačenje, valjanje in rezanje, transporter za vračanje palic, skladišče palic - Varnostne in higienske zahteve - Dopolnilo A1
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 13379:2002/kFprA1:2012
01-julij-2012
6WURML]DL]GHODYRWHVWHQLQ6WURML]DUD]YODþHQMHYDOMDQMHLQUH]DQMHSDOLþQR
SRYUDWQLWHNRþLWUDNVNODGLãþH9DUQRVWQHLQKLJLHQVNH]DKWHYH'RSROQLOR$
Pasta processing plants - Spreader, stripping and cutting machine, stick return conveyor,
stick magazine - Safety and hygiene requirements
Maschinen zur Teigwarenherstellung - Behänger, Abstreif- und Schneidmaschinen,
Stabrücktransporte, Stabmagazine - Sicherheits- und Hygieneanforderungen
Machines pour pâtes alimentaires - Etendeuse, dégarnisseuse-découpeuse, convoyeur
de retour des cannes et accumulateur de cannes - Prescriptions de sécurité et d'hygiène
Ta slovenski standard je istoveten z: EN 13379:2001/FprA1
ICS:
67.260 Tovarne in oprema za Plants and equipment for the
živilsko industrijo food industry
SIST EN 13379:2002/kFprA1:2012 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 13379:2002/kFprA1:2012
---------------------- Page: 2 ----------------------
SIST EN 13379:2002/kFprA1:2012
EUROPEAN STANDARD
FINAL DRAFT
EN 13379:2001
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
April 2012
ICS 67.260
English Version
Pasta processing plants - Spreader, stripping and cutting
machine, stick return conveyor, stick magazine - Safety and
hygiene requirements
Machines pour pâtes alimentaires - Etendeuse, Maschinen zur Teigwarenherstellung - Behänger, Abstreif-
dégarnisseuse-découpeuse, convoyeur de retour des
und Schneidmaschinen, Stabrücktransporte, Stabmagazine
cannes et accumulateur de cannes - Prescriptions de - Sicherheits- und Hygieneanforderungen
sécurité et d'hygiène
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 153.
This draft amendment A1, if approved, will modify the European Standard EN 13379:2001. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13379:2001/FprA1:2012: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 13379:2002/kFprA1:2012
EN 13379:2001/FprA1:2012 (E)
Contents Page
Foreword .4
1 Modification to the Foreword .5
2 Modification to the Introduction .5
3 Correction of the numbering of clauses and sub-clauses .5
4 Modification to Clause 1, Scope .6
5 Modification to Clause 2, Normative references .6
6 Modification to 3 Definitions, terminology and description .8
7 Modification to Clause 5, Safety requirements and/or measures .8
8 Modification to 5.1 Mechanical hazards .8
9 Modification to 5.1.1.1 .8
10 Modification to 5.1.1.3 .8
11 Modification to 5.1.1.5 .9
12 Modification to 5.1.1.6 .9
13 Modification to 5.1.2.1 .9
14 Modification to 5.1.2.7 .9
15 Modification to 5.1.3.3 .9
16 Modification to 5.1.4 Fluid ejection .9
17 Modification to 5.1.5 Unexpected start or failure of emergency device.9
18 Modification to 5.1.5.1 Supply disconnecting device .9
19 Modification to 5.1.5.2 Emergency stop device . 10
20 Modification to 5.1.5.3 Control circuits and control functions of stop device . 10
21 Modification to 5.1.5.4 Safety-related parts of control system . 10
22 Modification to 5.1.5.5 Automatic start warning . 10
23 Modification to 5.1.5.6 Safety limit device . 10
24 Modification to 5.1.5.7 Interlocking system of guards . 10
25 Modification to 5.1.5.8 Other requirements . 10
26 Modification to 5.1.5.9 Controls for maintenance operations . 11
27 Modification to 5.2 Electrical hazards . 11
28 Modification to 5.2.1.1 Direct contact . 11
29 Modification to 5.2.1.2 Indirect contact . 11
30 Modification to 5.2.2 Degrees of protection (see 12.3 of EN 60204-1:1997) . 11
31 Modification to 5.2.3 Cable section and colours . 11
32 Modification to 5.2.4 Electromagnetic compatibility . 11
33 Modification to 5.4 Noise reduction . 12
34 Modification to 5.5 Protective measures against slip, trip and fall . 12
2
---------------------- Page: 4 ----------------------
SIST EN 13379:2002/kFprA1:2012
EN 13379:2001/FprA1:2012 (E)
35 Modification to 5.6 Protective measures against hazards due to neglecting of hygienic
principles . 12
36 Modification to Clause 6, Verification . 12
37 Modification to Clause 7, Information for use (see Clause 5 of EN ISO 292-2:1991) . 13
38 Modification to 7.1 Technical information . 13
39 Modification to 7.2.1 General. 14
40 Modification to 7.2.2 Warning signs for residual hazard . 14
41 Modification to 7.3 Marking . 14
42 Modification to A.2.1.2 Materials for splash area . 14
43 Modification to A.2.1.3 Materials for non-food area . 15
44 Modification to A.2.2 Surface conditions . 15
45 Modification to A.3.1 Connections of internal surfaces . 15
46 Modification to A.3.3.1 Fasteners for food area . 15
47 Modification to B.1 Terms and definitions . 15
48 Modification to B.2 Installation and mounting conditions . 15
49 Modification to B.5 Emission sound pressure level determination . 15
50 Modification to B.6 Sound power level determination . 15
51 Modification to B.7 Measurement uncertainties . 16
52 Modification to B.10 Declaration and verification of noise emission value . 16
53 Modification to Annex ZA . 16
54 Modification to Bibliography . 17
3
---------------------- Page: 5 ----------------------
SIST EN 13379:2002/kFprA1:2012
EN 13379:2001/FprA1:2012 (E)
Foreword
This document (EN 13379:2001/FprA1:2012) has been prepared by Technical Committee CEN/TC 153
“Machinery intended for use with foodstuffs and feed”, the secretariat of which is held by DIN.
This document is currently submitted to the Unique Acceptance Procedure.
The first reason for amending the published standard EN 13379:2001 is the revision of the EU-Machinery
Directive 98/37/EC into 2006/42/EC, requiring the adaptation of published European Standards cited in the
Official Journal of the European Union under that Directive.
Additionally, at this occasion the normative references have been updated, while also some other limited
improvements and corrections have been made.
4
---------------------- Page: 6 ----------------------
SIST EN 13379:2002/kFprA1:2012
EN 13379:2001/FprA1:2012 (E)
1 Modification to the Foreword
Delete the 5th sentence and replace it with the following:
“For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.”
2 Modification to the Introduction
Delete the existing introduction and replace it with the following:
“This European Standard is a type C standard as stated in EN ISO 12100.
The machinery concerned and the extent to which hazards, hazardous situations and hazardous events are
covered are indicated in the scope of this document.
When provisions of this type C standard are different from those which are stated in type A or B standards, the
provisions of this type C standard take precedence over the provisions of the other standards, for machines
that have been designed and built according to the provisions of this type C standard.
Complementary to the hygiene requirements common to all food processing machines, specific requirements
for cleanability and sanitation of the machines in the scope are formulated.”
3 Correction of the numbering of clauses and sub-clauses
According to CEN rules it is not admissible any more to have in an EN standard a clause that is followed by a
text passage which in turn is then followed by one or several sub-clauses to the aforementioned clause.
In other words:
If there is a "head clause" with several sub-clauses, e.g. a clause 5.1 with sub-clauses 5.1.1, 5.1.2 etc., there
should be no standard text directly below 5.1, but rather in 5.1.1 and 5.1.2 etc.
Therefore the following editorial modifications to EN 13379 are needed:
- Insert a new clause "4.1 General" as a subheading under "4 List of hazards".
- Insert a new clause "4.1.1 General" as a subheading under "4.1 Mechanical hazards".
- Insert a new clause "5.1 General" as a subheading under "5 Safety requirements and/or measures".
- Insert a new clause "5.1.1 General" as a subheading under "5.1 Mechanical hazards".
- Insert a new clause "5.1.5.1 General" as a subheading under "5.1.5 Unexpected start or failure of
emergency device".
- Insert a new clause "5.2.1 General" as a subheading under "5.2 Electrical hazards".
- Insert a new clause "5.6.1 General" as a subheading under "5.6 Protective measures against hazards due
to neglecting of hygienic principles".
- Insert a new clause "6.1 General" as a subheading under "6 Verification".
- Insert a new clause "A.1.1 General" as a subheading under "A.1 Terms and definitions".
- Insert a new clause "A.3.1.1 General" as a subheading under "A.3.1 Connections of internal surfaces".
5
---------------------- Page: 7 ----------------------
SIST EN 13379:2002/kFprA1:2012
EN 13379:2001/FprA1:2012 (E)
- Insert a new clause "B.1.1 General" as a subheading under "B.1 Terms and definitions".
The text passages directly following the main headings of each of the above-listed items are to be placed
under the respective new subheadings. The subsequent clauses and sub-clauses, are to be re-numbered
accordingly.
NOTE All of the following modification instructions in this document still refer, however, to the "old" (current) numbering
of EN 13379:2001.
4 Modification to Clause 1, Scope
Delete the last paragraph and replace it with the following:
"This European Standard is not applicable to machines in its scope which are manufactured before the date of
its publication as EN."
5 Modification to Clause 2, Normative references
st
Replace the 1 paragraph with the following:
“The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.”
Replace the normative references with the following:
"
EN 953:1997+A1:2009, Safety of machinery – Guards – General requirements for the design and construction
of fixed and movable guards
EN 982:1996+A1:2008, Safety of machinery – Safety requirements for fluid power systems and their
components – Hydraulics
EN 1088:1995+A2:2008, Safety of machinery – Interlocking devices associated with guards – Principles for
design and selection
EN 1672-2:2005+A1:2009, Food processing machinery – Basic concepts – Part 2: Hygiene requirements
EN 60204-1:2006, Safety of machinery – Electrical equipment of machines – Part 1: General requirements
(IEC 60204-1:2005, modified)
EN 60332-1-1:2004, Tests on electric and optical fibre cables under fire conditions – Part 1-1: Test for vertical
flame propagation for a single insulated wire or cable – Apparatus (IEC 60332-1-1:2004)
EN 60332-1-2:2004, Tests on electric and optical fibre cables under fire conditions – Part 1-2: Test for vertical
flame propagation for a single insulated wire or cable – Procedure for 1 kW pre-mixed flame (IEC 60332-1-
2:2004)
EN 60332-1-3:2004, Tests on electric and optical fibre cables under fire conditions – Part 1-3: Test for vertical
flame propagation for a single insulated wire or cable – Procedure for determination of flaming
droplets/particles (IEC 60332-1-3:2004)
EN 60529:1991, Degrees of protection provided by enclosures (IP code) (IEC 60529:1989)
6
---------------------- Page: 8 ----------------------
SIST EN 13379:2002/kFprA1:2012
EN 13379:2001/FprA1:2012 (E)
EN 61496:2004, Safety of machinery – Electro-sensitive protective equipment – Part 1: General requirements
and tests, (IEC 61496-1:2004, modified)
EN ISO 3744:2010, Acoustics – Determination of sound power levels and sound energy levels of noise
sources using sound pressure – Engineering methods for an essentially free field over a reflecting plane (ISO
3744:2010)
EN ISO 3746:2010, Acoustics – Determination of sound power levels and sound energy levels of noise
sources using sound pressure – Survey method using an enveloping measurement surface over a reflecting
plane (ISO 3746:2010)
EN ISO 4414:2010, Pneumatic fluid power – General rules and safety requirements for systems and their
components (ISO 4414:2010)
EN ISO 4871:2009, Acoustics – Declaration and verification of noise emission values of machinery and
equipment (ISO 4871:1996)
EN ISO 7731:2008, Ergonomics – Danger signals for public and work areas – Auditory danger signals
(ISO 7731:2003)
EN ISO 9614-1:2009, Acoustics – Determination of sound power levels of noise sources using sound intensity
– Part 1: Measurement at discrete points (ISO 9614-1:1993)
EN ISO 9614-2:1996, Acoustics – Determination of sound power levels of noise sources using sound intensity
– Part 2: Measurement by scanning (ISO 9614-2:1996)
EN ISO 11204:2010, Acoustics – Noise emitted by machinery and equipment – Determination of emission
sound pressure levels at a work station and at other specified positions applying accurate environmental
corrections (ISO 11204:2010)
EN ISO 11688-1:2009, Acoustics – Recommended practice for the design of low-noise machinery and
equipment – Part 1: Planning (ISO/TR 11688-1:1995)
EN ISO 12100:2010, Safety of machinery – General principles for design – Risk assessment and risk
reduction (ISO 12100:2010)
EN IS
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.