65.040.10 - Livestock buildings, installations and equipment
ICS 65.040.10 Details
Livestock buildings, installations and equipment
Gebaude, Anlagen und Gerate fur Tierhaltung
Bâtiments, installations et équipements pour le bétail
Poslopja, naprave in oprema za živino
General Information
e-Library Subscription
Create subscription and get permanent access to documents within 65.040.10 - Livestock buildings, installations and equipment
Currently subscription includes documents marked with .We are working on making all documents available within the subscription.
1.1 This document specifies requirements for design, performance, safety and hygiene of refrigerated bulk milk coolers and the related methods of test.
NOTE The informative Annex J gives some elements regarding the estimation and calculation of energy consumption.
This document deals with all significant hazards, hazardous situations and events relevant to bulk milk coolers on farm, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4).
It applies to refrigerated bulk milk tanks with air-cooled condensing units and automatic control intended for installation on farms or at milk collection points. It applies to tanks for two milkings (24 h), four milkings (48 h) and six milkings (72 h), in which the cooling takes place totally (non-pre-cooled milk) or partially (in case of pre-cooled milk) within the tank. It also applies to tanks in combination with a continuous system of milking (e.g. milking with robot).
1.2 This document does not cover:
- mobile tanks;
- tanks intended to be tilted for drainage;
- equipment for delivering the milk to the tank;
- equipment for pre-cooling of the milk;
- the hazards due to the use of other energy than electrical energy;
- pressure aspect of vacuum tanks (i.e. tanks where the inner part of the vessel is designed to operate at a pressure below atmospheric pressure).
1.3 Noise is not considered to be a significant hazard, but relevant for bulk milk coolers. This document therefore includes information in 7.1 and in Annex A concerning the manufacturer's declaration of the noise emission level of the cooler.
1.4 This document does not cover the calibration requirements for the tank to be used as a system for payment purpose.
1.5 This document is not applicable to bulk milk coolers on farm which are manufactured before the date of its publication as EN.
- Standard98 pagesEnglish languagesale 10% offe-Library read for1 day
1.1 This document specifies requirements for design, performance, safety and hygiene of refrigerated bulk milk coolers and the related methods of test.
NOTE The informative Annex K gives some elements regarding the estimation and calculation of energy consumption.
This document deals with all significant hazards, hazardous situations and events relevant to bulk milk coolers on farm, when they are installed, used and maintained as intended by the manufacturer (see informative Annex A).
It applies to refrigerated bulk milk tanks with air-cooled condensing units and automatic control intended for installation on farms or at milk collection points. It applies to tanks for two milkings (24 h), four milkings (48 h) and six milkings (72 h), in which the cooling takes place totally (non-pre-cooled milk) or partially (in case of pre-cooled milk) within the tank. It also applies to tanks in combination with a continuous system of milking (e.g. milking with robot).
1.2 This document does not cover:
- mobile tanks;
- tanks intended to be tilted for drainage;
- equipment for delivering the milk to the tank;
- equipment for pre-cooling of the milk;
- the hazards due to the use of other energy than electrical energy;
- pressure aspect of vacuum tanks (tank of which the inner vessel is designed to operate at a pressure below atmospheric pressure);
- calibration requirements for the measurement of the milk volume.
1.3 This document is not applicable to bulk milk coolers on farms which are manufactured before the date of its publication as EN.
- Standard98 pagesEnglish languagesale 10% offe-Library read for1 day
1.1 General
This document specifies the standardization of side curtain ventilation systems as defined in 3.1. This document specifies the safety aspects and performance. Included are machines that operate using the potential energy stored by the earlier application of human or animal force, such as stretched springs.
This document addresses the following significant hazards associated with side curtain systems:
- crushing;
- cutting or severing;
- drawing-in or trapping;
- entanglement;
- shearing;
- suffocation;
- electrocution and shock;
- incorrect design, location or identification of control devices.
1.2 Exclusions
This document does not apply to the following, which are intended for a different use:
- doors and side curtains when used as doors which are specified in EN 13241:2003+A2:2016;
- systems inflated by air;
- screens supplied for the control of fire or smoke;
- screens that move instantaneously upon the application of human force;
- side curtains when used to control ventilation conditions in a toxic or explosive environment.
This document is not applicable to side curtain ventilation systems manufactured before the date of its publication.
- Standard64 pagesEnglish languagesale 10% offe-Library read for1 day
This clause of Part 1 is replaced by the following.
This part of IEC 60335 deals with the safety of electric fence energizers, the rated voltage
of which is not more than 250 V and by means of which fence wires in agricultural, domestic
or feral animal control fences and security fences may be electrified or monitored.
NOTE 101 Examples of electric fence energizers coming within the scope of this standard are:
– mains-operated energizers;
– battery-operated electric fence energizers suitable for connection to the mains, as shown in Figure 101
and Figure 102;
– electric fence energizers operated by non-rechargeable batteries either incorporated or separate.
This standard does not in general take into account
– the use of appliances by young children or infirm persons without supervision;
– the playing with appliances by young children.
NOTE 102 Attention is drawn to the fact that
– for appliances intended to be used on board ships or aircraft, additional requirements can be necessary;
– in many countries, additional requirements are specified by the national health authorities, the national
authorities responsible for the protection of labour, the national water supply authorities and similar authorities.
NOTE 103 This standard does not apply to
– electromagnetically coupled animal trainer collars;
– appliances intended to be used in locations where special conditions prevail, such as the presence of a
corrosive or explosive atmosphere (dust, vapour or gas);
– separate battery chargers (IEC 60335-2-29);
– electric fishing machines (IEC 60335-2-86);
– electric animal-stunning equipment (IEC 60335-2-87);
– appliances for medical purposes (IEC 60601
- Standard63 pagesEnglish languagesale 10% offe-Library read for1 day
Applicable to the safety of electric fence energizers, the rated voltage of which is not more than 250 V.
- Amendment12 pagesEnglish languagesale 10% offe-Library read for1 day
This European standard specifies the standardisation of side curtain ventilation systems supplied for environmental control, installed on farm buildings, that use a barrier made from a flexible foil or fabric which move via a rolling or folding action, or rigid panels that slide; as far as safety aspects, performance and sustainebility issues are concerned. Included are machines that operate using the potential energy stored by the earlier application of human or animal force, such as stretched springs.
- Standard64 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies minimum performance and information requirements for monitoring devices of bulk milk cooling tanks as part of milking and milk cooling machinery installations in agricultural operations. It also specifies the minimum requirements for materials, design and installation. The purpose of this document is to contribute to a high-quality milk production by monitoring, collecting data and providing alarms with respect to defined parameters of the milk cooling, storage and cleaning processes.
- Standard6 pagesEnglish languagesale 15% off
- Standard6 pagesEnglish languagesale 15% off
- Standard6 pagesFrench languagesale 15% off
- Standard6 pagesFrench languagesale 15% off
TC 61 advise on 2016-02-01: Common modifications needed but experts on these products not yet detected and not declared their availability to prepare a suitable proposal
- Amendment7 pagesEnglish languagesale 10% offe-Library read for1 day
This document specifies the requirements for reinforced and prestressed precast concrete floor slats used in slatted floors for the housing of livestock and provides for the evaluation of conformity of these products. This document does not cover slats for loadings other than stock and stockmen.
- Standard32 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the requirements for reinforced and prestressed precast concrete floor slats used in slatted floors for the housing of livestock and provides for the evaluation of conformity of these products. This standard does not cover slats for loadings other than stock and stockmen.
- Standard32 pagesEnglish languagesale 10% offe-Library read for1 day
Amandma A1:2007 je dodatek k standardu SIST EN 60335-2-70:2003
Deals with the safety of milking machines, to be used in stalls and in the open, that are designed for milking farm animals, such as cows, the rated voltage of the milking machines being not more than 250 V for single-phase operation and 480 V for other operations.
- Amendment7 pagesEnglish languagesale 10% offe-Library read for1 day
ISO 5707:2007 specifies the minimum performance and information requirements and certain dimensional requirements for satisfactory functioning of milking machines, for milking and cleaning. It also specifies minimum requirements for materials, design, manufacture and installation. ISO 5707:2007 is applicable to milking machines for milking cows, water buffaloes, sheep and goats where animals are milked with pulsation created by vacuum, and where milk is, at least partly, transported with the help of air flow. Some clauses are not applicable to all types of milking machines. The qualitative requirements also apply to installations for milking other mammals used for milk production.
- Standard50 pagesEnglish languagesale 15% off
- Standard53 pagesFrench languagesale 15% off
ISO 20966:2007 specifies requirements for the construction of automatic milking installations (AMI), including specific safety and hygiene aspects and minimum performance requirements and testing, in addition to those described in ISO 5707 and ISO 6690. It does not contain requirements for the design of the building in which the milking installation is installed.
- Standard14 pagesEnglish languagesale 15% off
- Standard15 pagesFrench languagesale 15% off
ISO 6690:2007 specifies mechanical tests for milking machine installations in order to verify compliance of an installation or component with the requirements of ISO 5707. It also stipulates the accuracy requirements for the measuring instruments. ISO 6690:2007 is applicable for testing new installations and for periodic checking of installations for efficiency of operation. Alternative test methods may be applicable if they can be shown to achieve comparable results. The test procedures described are primarily for testing in the laboratory. An example of a field test procedure which can reduce the time and effort involved in testing is given together with the corresponding test report.
- Standard38 pagesEnglish languagesale 15% off
- Standard40 pagesFrench languagesale 15% off
ISO 3918:2007 defines terms to be used in research work, official regulations, design, manufacture, installation and use of milking machines for cows, water buffaloes, sheep, goats or other mammals used for milk production.
- Standard35 pagesEnglish languagesale 15% off
Deals with milking machines for milking farm animals, for use in stalls or in the open. Examples are bucket and direct-to-can milking machines, milking pipeline machines, recorder milking machines. The rated voltage is less than 250 V for single-phase operation and 480 V for other operations.
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
Specifies certain requirements for design, construction and performance of refrigerated tanks and the related of test. It does not deal with electrical safety regulations. Applies to refrigerated tanks with automatic control intended for fixed or mobile installation in farms or at milk collecting points. It only applies to tanks for two milkings (24 h) and four milkings (48 h).
- Standard19 pagesEnglish languagesale 15% off
- Standard20 pagesFrench languagesale 15% off
- Standard20 pagesFrench languagesale 15% off
Specifies requirements for the characteristics, dimensions, methods of installation and safety of closed- circuit conveyors. Applies to evacuation devices fitted with scrapers, moving continuously in a closed circuit, inteded to remove solid and liquid manure collected in non- grid covered channels in enclosed stalls. It applies to elevators only in so far as these from part of the circuit.
- Standard2 pagesEnglish languagesale 15% off
- Standard2 pagesFrench languagesale 15% off
- Standard2 pagesFrench languagesale 15% off
- Draft10 pagesEnglish languagesale 10% offe-Library read for1 day
D142/C058: NWI approved * Enquiries for prAE (PR=23101), prAF (PR=24113) and prAG (PR=24114) to be circulated together with same limit dates for comments
- Draft4 pagesEnglish languagesale 10% offe-Library read for1 day
D142/C058: NWI approved * Enquiries for prAE (PR=23101), prAF (PR=24113) and prAG (PR=24114) to be circulated together with same limit dates for comments
- Draft3 pagesEnglish languagesale 10% offe-Library read for1 day
D137/C170: NWI approved with target date for vote: 2011-06-30
- Draft5 pagesEnglish languagesale 10% offe-Library read for1 day
- Corrigendum3 pagesEnglish languagesale 10% offe-Library read for1 day
This part of IEC 60335 deals with the safety of electric fence energizers, the rated voltage
of which is not more than 250 V and by means of which fence wires in agricultural, domestic
or feral animal control fences and security fences may be electrified or monitored.
- Standard63 pagesEnglish languagesale 10% offe-Library read for1 day
1.1 This European Standard specifies requirements for design, performance, safety and hygiene of refrigerated bulk milk coolers and the related methods of test.
This standard deals with all significant hazards, hazardous situations and events relevant to bulk milk coolers on farms, when they are used as intended and under the conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4).
It applies to refrigerated bulk milk tanks with air cooled condensing units and automatic control intended for installation on farms or at milk collecting points. It applies to tanks for two milkings (24 h), four milkings (48 h) and six milkings (72 h), in which the cooling takes place totally (non-pre-cooled milk) or partially (in case of pre-cooled milk) within the tank.
Performance requirements in 5.5.1.2.1 and 5.5.1.2.2 do not apply to tanks in combination with instant cooling or in association with a continuous system of milking (e.g. milking with robot).
1.2 This European Standard does not cover:
- mobile tanks;
- tanks intended to be tilted for drainage;
- equipment for delivering the milk to the tank;
- equipment for pre-cooling or instant cooling of the milk;
- the hazards due to the use of other energy than electrical energy;
- pression aspect of vacuum tanks.
1.3 Noise is not considered to be a significant hazard, but a relevant one for bulk milk coolers. This standard therefore includes information in 7.1 and in Annex A concerning the manufacturer's declaration of the noise emission level of the cooler.
1.4 This standard does not cover the calibration requirements for the tank to be used as a system for payment purpose.
1.5 This standard is not applicable to bulk milk coolers on farms which are manufactured before the date of its publication as an EN.
- Standard72 pagesEnglish languagesale 10% offe-Library read for1 day
2015-03-11: PR=24832 covering CMs to EN 60335-2-76:2005/FprA2:2013 merged in A2:2015 * FprAE (23101) also merged with 23990
- Amendment14 pagesEnglish languagesale 10% offe-Library read for1 day
This International Standard deals with the safety of electric fence energizers, the rated voltage of which is not more than 250 V and by means of which fence wires in agricultural, domestic or feral animal control fences and security fences may be electrified or monitored.
- Amendment6 pagesEnglish languagesale 10% offe-Library read for1 day
To be implemented in all countries with exception of CH * See D129/130 (new implementation dates) and D129/131 (not to be published before 2008-01-01)
- Amendment3 pagesEnglish languagesale 10% offe-Library read for1 day
Incorporates EN 60335-2-76:2005/prAA (pr=16650)
- Amendment6 pagesEnglish languagesale 10% offe-Library read for1 day
Applicable to the safety of electric fence energizers, the rated voltage of which is not more than 250 V.
- Standard48 pagesEnglish languagesale 10% offe-Library read for1 day
1.1 This European Standard specifies requirements for design, construction, performance, suitability for use, safety and hygiene of refrigerated bulk bovine milk coolers and the related methods of test.
It applies to refrigerated bulk milk tanks with air cooled condensing units and automatic control intended for installation on farms or at milk collecting points. It applies to tanks for two milkings (24 h), four milkings (48 h) and six milkings (72 h), in which the cooling takes place totally or partially within the tank.
Performance requirements in 5.4.1.2.1 and 5.4.1.2.2 do not apply to tanks where cooling does not take place totally within the tank nor where the tank is associated with a continuous system of milking (e.g. milking with robot).
1.2 This European Standard does not cover:
- mobile tanks;
- tanks intended to be tilted for drainage;
- equipment for delivering the milk to the tank;
- equipment for pre-cooling or instant cooling of the milk.
1.3 This standard covers significant hazards at machines falling within this scope when used as intended by the manufacturer and as identified by risk assessment (see EN 1050:1997).
Noise is not considered to be a significant hazard for bulk milk coolers. This standard includes information in 7.1 and in annex A concerning the manufacturer's declaration of the noise emission level of the cooler.
1.4 This standard does not cover the calibration requirements for the tank to be used as a system for payment purpose.
1.5 This standard applies primarily to the machines which are manufactured after its date of issue.
- Standard63 pagesEnglish languagesale 10% offe-Library read for1 day
1.1 This European Standard specifies requirements for design, construction, performance, suitability for use, safety and hygiene of refrigerated bulk bovine milk coolers and the related methods of test.
It applies to refrigerated bulk milk tanks with air cooled condensing units and automatic control intended for installation on farms or at milk collecting points. It applies to tanks for two milkings (24 h), four milkings (48 h) and six milkings (72 h), in which the cooling takes place totally or partially within the tank.
Performance requirements in 5.4.1.2.1 and 5.4.1.2.2 do not apply to tanks where cooling does not take place totally within the tank nor where the tank is associated with a continuous system of milking (e.g. milking with robot).
1.2 This European Standard does not cover:
- mobile tanks;
- tanks intended to be tilted for drainage;
- equipment for delivering the milk to the tank;
- equipment for pre-cooling or instant cooling of the milk.
1.3 This standard covers significant hazards at machines falling within this scope when used as intended by the manufacturer and as identified by risk assessment (see EN 1050:1997).
Noise is not considered to be a significant hazard for bulk milk coolers. This standard includes information in 7.1 and in annex A concerning the manufacturer's declaration of the noise emission level of the cooler.
1.4 This standard does not cover the calibration requirements for the tank to be used as a system for payment purpose.
1.5 This standard applies primarily to the machines which are manufactured after its date of issue.
- Standard63 pagesEnglish languagesale 10% offe-Library read for1 day
Size of the manholes refered to 5.5.2.3 and 5.9.1
- Amendment3 pagesEnglish languagesale 10% offe-Library read for1 day
1.1 This European Standard specifies requirements for design, construction, performance, suitability for use, safety and hygiene of refrigerated bulk bovine milk coolers and the related methods of test.
It applies to refrigerated bulk milk tanks with air cooled condensing units and automatic control intended for installation on farms or at milk collecting points. It applies to tanks for two milkings (24 h), four milkings (48 h) and six milkings (72 h), in which the cooling takes place totally or partially within the tank.
Performance requirements in 5.4.1.2.1 and 5.4.1.2.2 do not apply to tanks where cooling does not take place totally within the tank nor where the tank is associated with a continuous system of milking (e.g. milking with robot).
- Standard61 pagesEnglish languagesale 10% offe-Library read for1 day
Size of the manholes refered to 5.5.2.3 and 5.9.1
- Amendment3 pagesEnglish languagesale 10% offe-Library read for1 day
1.1 This European Standard specifies requirements for design, construction, performance, suitability for use, safety and hygiene of refrigerated bulk bovine milk coolers and the related methods of test.
It applies to refrigerated bulk milk tanks with air cooled condensing units and automatic control intended for installation on farms or at milk collecting points. It applies to tanks for two milkings (24 h), four milkings (48 h) and six milkings (72 h), in which the cooling takes place totally or partially within the tank.
Performance requirements in 5.4.1.2.1 and 5.4.1.2.2 do not apply to tanks where cooling does not take place totally within the tank nor where the tank is associated with a continuous system of milking (e.g. milking with robot).
- Standard61 pagesEnglish languagesale 10% offe-Library read for1 day
This clause of Part 1 is applicable except as follows: 1.1 Replacement. This standard applies to automatically-controlled refrigerated bulk-milk tanks intended for fixed or mobile installation on farms or at milk collecting points having a rated volume not exceeding 25 000 litres. It also applies to immersion coolers and to equipment delivered as a number of units for assembly into a single appliance. NOTE 1 : Bulk-milk coolers can be combined with heat-recovery units. NOTE 2: This standard does not apply to: - milk coolers incorporated in heating systems; - milk coolers having a pre-cooling system; - instantaneous milk coolers; - refrigerators and food freezers (EN 60335-2-44). NOTE 3: For bulk-milk coolers intended to be used in vehicles or on board ships, additional requirements may be necessary. NOTE 4: Attention is drawn to the fact that in many countries additional requirements are specified by the national health authorities, the national authorities responsible for the protection of labour, the national water supply authorities and similar authorities.
- Standard14 pagesEnglish languagesale 10% offe-Library read for1 day
EN following parallel vote * Superseded by EN 60335-2-76:1999
- Amendment32 pagesEnglish languagesale 10% offe-Library read for1 day
Superseded by EN 60335-2-76:2005
- Amendment3 pagesEnglish languagesale 10% offe-Library read for1 day
- Amendment11 pagesEnglish languagesale 10% offe-Library read for1 day
EN following parallel vote * Superseded by EN 60335-2-76:1999
- Amendment4 pagesEnglish languagesale 10% offe-Library read for1 day
Corrigendum to EN issued April 1993 * Superseded by EN 60335-2-76:1999
- Standard21 pagesEnglish languagesale 10% offe-Library read for1 day
Certification period up to 2004-01-01 * Superseded by EN 60335-2-76:1999
- Amendment2 pagesEnglish languagesale 10% offe-Library read for1 day
EN following parallel vote * Superseded by EN 60335-2-76:1999
- Amendment5 pagesEnglish languagesale 10% offe-Library read for1 day
Corrigendum to EN issued April 1993 * Supersedes HD 92 S1 * Superseded by EN 60335-2-76:1999
- Standard107 pagesEnglish languagesale 10% offe-Library read for1 day
Corrigendum to EN issued April 1993 * Superseded by EN 60335-2-76:1999
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
Deals with the safety of electric fence energizers for agricultural, feral animal control and security fences. This includes mains-operated and battery-operated energizers.
- Standard36 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the requirements for reinforced and prestressed precast concrete floor slats used in slatted floors for the housing of livestock and provides for the evaluation of conformity of these products. This standard does not cover slats for loadings other than stock and stockmen.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
This European Standard specifies the requirements for reinforced and prestressed precast concrete floor slats used in slatted floors for the housing of livestock and provides for the evaluation of conformity of these products. This standard does not cover slats for loadings other than stock and stockmen.
- Standard18 pagesEnglish languagesale 10% offe-Library read for1 day
Work incorporated into PR=16649
- Amendment3 pagesEnglish languagesale 10% offe-Library read for1 day
Deals with the safety of milking machines to be used in stalls and in the open, which are designed for milking farm animals such as cows. The rated voltage of the milking machines is not more than 250 V for single-phase operation and 480 V for other operations.
- Standard19 pagesEnglish languagesale 10% offe-Library read for1 day