SIST EN IEC 61754-4:2022
(Main)Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 4: Type SC connector family (IEC 61754-4:2022)
Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 4: Type SC connector family (IEC 61754-4:2022)
This part of IEC 61754 specifies the standard interface dimensions for type SC family of connectors.
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Steckgesichter von Lichtwellenleiter-Steckverbindern - Teil 4: Steckverbinderfamilie der Bauart SC (IEC 61754-4:2022)
Dispositifs dinterconnexion et composants passifs à fibres optiques Interfaces de connecteurs pour fibres optiques Partie 4: Famille de connecteurs du type SC (IEC 61754-4:2022)
IEC 61754-4:2022 est disponible sous forme de IEC 61754-4:2022 RLV qui contient la Norme internationale et sa version Redline, illustrant les modifications du contenu technique depuis l'édition précédente.
L'IEC 61754-4:2022 spécifie les dimensions d'interfaces normalisées pour la famille de connecteurs de type SC. La présente troisième édition annule et remplace la deuxième édition publiée en 2013, et constitue une révision technique. La présente édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:
- ajout de la méthode d'essai de l'IEC 61300-3-22 sur la force de compression de la férule;
- ajout de l'Annexe A (informative) avec les exigences relatives aux dimensions des découpes pour réaliser les essais de résistance des raccords montés.
Optični spojni elementi in pasivne komponente - Vmesniki za optične konektorje - 4. del: Konektorska družina vrste SC (IEC 61754-4:2022)
Ta del standarda IEC 61754 navaja standardne dimenzije vmesnikov za konektorsko družino vrste SC.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 61754-4:2022
01-junij-2022
Nadomešča:
SIST EN 61754-4:2014
SIST EN 61754-4:2014/AC:2015
Optični spojni elementi in pasivne komponente - Vmesniki za optične konektorje -
4. del: Konektorska družina vrste SC (IEC 61754-4:2022)
Fibre optic interconnecting devices and passive components - Fibre optic connector
interfaces - Part 4: Type SC connector family (IEC 61754-4:2022)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Steckgesichter von
Lichtwellenleiter-Steckverbindern - Teil 4: Steckverbinderfamilie der Bauart SC (IEC
61754-4:2022)
Dispositifs dinterconnexion et composants passifs à fibres optiques Interfaces de
connecteurs pour fibres optiques Partie 4: Famille de connecteurs du type SC (IEC
61754-4:2022)
Ta slovenski standard je istoveten z: EN IEC 61754-4:2022
ICS:
33.180.20 Povezovalne naprave za Fibre optic interconnecting
optična vlakna devices
SIST EN IEC 61754-4:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 61754-4:2022
---------------------- Page: 2 ----------------------
SIST EN IEC 61754-4:2022
EUROPEAN STANDARD EN IEC 61754-4
NORME EUROPÉENNE
EUROPÄISCHE NORM April 2022
ICS 33.180.20 Supersedes EN 61754-4:2013 and all of its amendments
and corrigenda (if any)
English Version
Fibre optic interconnecting devices and passive components -
Fibre optic connector interfaces - Part 4: Type SC connector
family
(IEC 61754-4:2022)
Dispositifs d'interconnexion et composants passifs Lichtwellenleiter - Verbindungselemente und passive
fibroniques - Interfaces de connecteurs fibroniques - Bauteile - Steckgesichter von Lichtwellenleiter-
Partie 4: Famille de connecteurs de type SC Steckverbindern - Teil 4: Steckverbinderfamilie der Bauart
(IEC 61754-4:2022) SC
(IEC 61754-4:2022)
This European Standard was approved by CENELEC on 2022-04-04. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61754-4:2022 E
---------------------- Page: 3 ----------------------
SIST EN IEC 61754-4:2022
EN IEC 61754-4:2022 (E)
European foreword
The text of document 86B/4563/FDIS, future edition 3 of IEC 61754-4, prepared by SC 86B "Fibre
optic interconnecting devices and passive components" of IEC/TC 86 "Fibre optics" was submitted to
the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 61754-4:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-01-04
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2023-04-04
document have to be withdrawn
This document supersedes EN 61754-4:2013 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61754-4:2022 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 61300-2-55 NOTE Harmonized as EN 61300-2-55
IEC 61755-3-1 NOTE Harmonized as EN 61755-3-1
IEC 61755-3-2 NOTE Harmonized as EN 61755-3-2
2
---------------------- Page: 4 ----------------------
SIST EN IEC 61754-4:2022
EN IEC 61754-4:2022 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 61300-3-22 - Fibre optic interconnecting devices and EN 61300-3-22 -
passive components - Basic test and
measurement procedures - Part 3-22:
Examinations and measurements - Ferrule
compression force
IEC 61754-1 - Fibre optic interconnecting devices and EN 61754-1 -
passive components - Fibre optic
connector interfaces - Part 1: General and
guidance
3
---------------------- Page: 5 ----------------------
SIST EN IEC 61754-4:2022
---------------------- Page: 6 ----------------------
SIST EN IEC 61754-4:2022
IEC 61754-4
®
Edition 3.0 2022-02
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fibre optic interconnecting devices and passive components – Fibre optic
connector interfaces –
Part 4: Type SC connector family
Dispositifs d’interconnexion et composants passifs fibroniques – Interfaces de
connecteurs fibroniques –
Partie 4: Famille de connecteurs de type SC
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.20 ISBN 978-2-8322-1077-6
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN IEC 61754-4:2022
– 2 – IEC 61754-4:2022 © IEC 2022
CONTENTS
FOREWORD . 4
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Description . 6
5 Interfaces . 7
Annex A (informative) Panel dimensions . 35
A.1 General . 35
A.2 Simplex adaptor . 35
A.3 Duplex adaptor . 35
Bibliography . 37
Figure 1 – Simplex PC plug connector interface . 8
Figure 2 – Simplex adaptor connector interface . 11
Figure 3 – Pin gauge for adaptor . 12
Figure 4 – Duplex PC plug connector interface . 13
Figure 5 – Duplex adaptor connector interface . 16
Figure 6 – Simplex angled PC plug connector interface . 18
Figure 7 – Duplex angled PC plug connector interface . 20
Figure 8 – Simplex active device receptacle interface for angled PC connector plug . 23
Figure 9 – Simplex active device receptacle interface for PC connector plug . 26
Figure 10 – Duplex active device receptacle interface for angled PC connector plug. 29
Figure 11 – Duplex active device receptacle interface for PC connector plug . 32
Figure A.1 – Panel cut out . 35
Figure A.2 – Fixture cut out . 35
Table 1 – Interfaces . 7
Table 2 – Intermateability of interfaces . 7
Table 3 – Dimensions of the simplex PC plug connector interface . 9
Table 4 – Grade characteristics for simplex PC plug connector . 10
Table 5 – Dimensions of the simplex adaptor connector interface . 11
Table 6 – Grade characteristics for simplex adaptor connector . 12
Table 7 – Pin gauge dimensions . 12
Table 8 – Dimensions of the duplex PC plug connector interface . 14
Table 9 – Grade characteristics for duplex PC plug connector . 15
Table 10 – Dimensions of the duplex adaptor connector interface . 17
Table 11 – Grade of the duplex adaptor connector . 17
Table 12 – Dimensions of the simplex angled PC plug connector interfaces . 19
Table 13 – Dimensions of the duplex angled PC plug connector interfaces . 21
Table 14 – Dimensions of the simplex active device receptacle interface for angled PC
connector plug . 24
---------------------- Page: 8 ----------------------
SIST EN IEC 61754-4:2022
IEC 61754-4:2022 © IEC 2022 – 3 –
Table 15 – Alignment feature grade of the simplex active device receptacle interface
for angled PC connector plug . 25
Table 16 – Mechanical stop feature grade of the simplex active device receptacle
interface for angled PC connector plug . 25
Table 17 – Dimensions of the simplex active device receptacle interface for PC
connector plug . 27
Table 18 – Alignment feature grade of the simplex active device receptacle interface
for PC connector plug . 28
Table 19 – Mechanical stop feature grade of the simplex active device receptacle
interface for PC connector plug . 28
Table 20 – Dimensions of the duplex active device receptacle interface for angled PC
connector plug . 30
Table 21 – Alignment feature grade of the duplex active device receptacle interface for
angled PC connector plug . 31
Table 22 – Mechanical stop feature grade of the duplex active device receptacle
interface for angled PC connector plug . 31
Table 23 – Dimensions of the duplex active device receptacle interface for PC
connector plug . 33
Table 24 – Alignment feature grade of the duplex active device receptacle interface for
PC connector plug . 34
Table 25 – Mechanical stop feature grade of the duplex active device receptacle
interface for PC connector plug . 34
Table A.1 – Dimensions for simplex adaptor . 35
Table A.2 – Dimensions for duplex adaptor . 36
---------------------- Page: 9 ----------------------
SIST EN IEC 61754-4:2022
– 4 – IEC 61754-4:2022 © IEC 2022
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIBRE OPTIC INTERCONNECTING
DEVICES AND PASSIVE COMPONENTS –
FIBRE OPTIC CONNECTOR INTERFACES –
Part 4: Type SC connector family
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
IEC 61754-4 has been prepared by subcommittee 86B: Fibre optic interconnecting devices and
passive components, of IEC technical committee 86: Fibre optics. It is an International Standard.
This third edition cancels and replaces the second edition published in 2013 and constitutes a
technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) the test method IEC 61300-3-22 for the compression force of the ferrule was added;
b) Annex A (informative) with cut out dimension requirements for testing the strength of
mounted adaptors was added.
---------------------- Page: 10 ----------------------
SIST EN IEC 61754-4:2022
IEC 61754-4:2022 © IEC 2022 – 5 –
The text of this International Standard is based on the following documents:
Draft Report on voting
86B/4563/FDIS 86B/4584/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available
at www.iec.ch/members_experts/refdocs. The main document types developed by IEC are
described in greater detail at www.iec.ch/standardsdev/publications.
A list of all parts of the IEC 61754 series, under the general title Fibre optic interconnecting
devices and passive components – Fibre optic connector interfaces, can be found on the IEC
website.
Future standards in this series will carry the new general title as cited above. Titles of existing
standards in this series will be updated at the time of the next edition.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 11 ----------------------
SIST EN IEC 61754-4:2022
– 6 – IEC 61754-4:2022 © IEC 2022
FIBRE OPTIC INTERCONNECTING
DEVICES AND PASSIVE COMPONENTS –
FIBRE OPTIC CONNECTOR INTERFACES –
Part 4: Type SC connector family
1 Scope
This part of IEC 61754 specifies the standard interface dimensions for type SC family of
connectors.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies.
For undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 61300-3-22, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 3-22: Examinations and measurements – Ferrule compression
force
IEC 61754-1, Fibre optic interconnecting devices and passive components – Fibre optic
connector interfaces – Part 1: General and guidance
3 Terms and definitions
For the purposes of this document, the terms and definitions given in IEC 61754-1 apply.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
4 Description
The parent connector for the type SC connector family is a single position plug connector
characterized by a 2,5 mm nominal ferrule diameter. It includes a push-pull coupling mechanism
which is spring loaded relative to the ferrule in the direction of the optical axis. The plug has a
single male key which may be used to orient and limit the relative position between the
connector and the component to which it is mated. The optical alignment mechanism of the
connector is of a sleeve style.
This document defines the standard interface dimensions of active device receptacles for the
type SC connectors. The receptacles are used to retain the connector plug and mechanically
maintain the optical datum target of the plugs at a defined position within the receptacle
housings.
---------------------- Page: 12 ----------------------
SIST EN IEC 61754-4:2022
IEC 61754-4:2022 © IEC 2022 – 7 –
5 Interfaces
This document contains the standard interfaces showed in Table 1.
Table 1 – Interfaces
Interface IEC 61754-4-1 Simplex plug connector interface – push/pull, physical contact (PC)
Interface IEC 61754-4-2 Simplex adaptor connector interface – push/pull
Interface IEC 61754-4-3 Duplex plug connector interface – push/pull, PC
Interface IEC 61754-4-4 Duplex adaptor connector interface – push/pull
Interface IEC 61754-4-5 Simplex plug connector interface – push/pull, angled PC (APC) 8°
Interface IEC 61754-4-6 Duplex plug connector interface – push/pull, APC 8°
Interface IEC 61754-4-X1 Simplex active device receptacle interface – for APC 8°connector plug
Interface IEC 61754-4-X2 Simplex active device receptacle interface – for PC connector plug
Interface IEC 61754-4-X3 Duplex active device receptacle interface – for APC 8°connector plug
Interface IEC 61754-4-X4 Duplex active device receptacle interface – for PC connector plug
Table 2 shows the intermateability of interfaces.
Table 2 – Intermateability of interfaces
Adaptors/active device receptacles
Plugs
61754-4-2 61754-4-4 61754-4-X1 61754-4-X2 61754-4-X3 61754-4-X4
61754-4-1 Mate Mate Not mate Mate Not mate Mate
61754-4-3 Not mate Mate Not mate Not mate Not mate Mate
61754-4-5 Mate Mate Mate Not mate Mate Not mate
61754-4-6 Not mate Mate Not mate Not mate Mate Not mate
Figure 1 is an example of a simplex PC plug connector interface. Table 3 gives dimensions of
the simplex PC plug connector interface and Table 4 gives the grade characteristics for simplex
PC plug connector interface.
A chamfer or radius is allowed to a maximum depth of 1,8 mm from the ferrule endface.
---------------------- Page: 13 ----------------------
SIST EN IEC 61754-4:2022
– 8 – IEC 61754-4:2022 © IEC 2022
Figure 1 – Simplex PC plug connector interface
---------------------- Page: 14 ----------------------
SIST EN IEC 61754-4:2022
IEC 61754-4:2022 © IEC 2022 – 9 –
Table 3 – Dimensions of the simplex PC plug connector interface
Reference Dimensions Remarks
Minimum Maximum
A See Table 4
B 4,8 mm 4,9 mm
C 6,8 mm 7,4 mm
D 4,9 mm 5,3 mm
E 6,7 mm 6,8 mm
F 19° 23° Angle, unit in degrees
G Angle, unit in degrees
25° 35°
a
H 7,15 mm 7,5 mm
I 0,8 mm 1,2 mm
J 5,3 mm 5,5 mm
K – 0,05 mm
b
L 2,11 mm –
b c
M 2,0 mm 2,8 mm
N 6,6 mm 6,8 mm
O 1,6 mm 1,8 mm
P 8,89 mm 8,99 mm
Q 0,8 mm 1,0 mm
R 7,29 mm 7,39 mm
S 0,8 mm 0,90 mm Radius
T 4,05 mm 4,15 mm
U 5,4 mm 5,6 mm
b
V 0 mm 0,5 mm
BC 0 mm 0,5 mm Chamfer or round
d
BF See IEC 61755-3-1
Radius
BG See IEC 61755-3-1 Diameter
BI Angle, unit in degrees
25° 35°
a
Dimension H is given for plug endface when not mated. The ferrule is movable by a certain axial compression
force, with direct contacting endfaces, and therefore dimension H is variable. Ferrule compression force shall
be 7,8 N to 11,8 N when dimension H is 7,0 mm ± 0,1 mm. The compression force shall be measured according
to IEC 61300-3-22.
b
The delatch housing shall be movable to the right or left. Dimensions L, M and V are given when the delatch
housing is at the furthest right. Dimension M shall be negative, when the delatch housing is at the furthest left.
c
The right end of M shall be at the left of the mechanical datum target when the delatch housing is at the furthest
left.
d
Dome eccentricity of the spherical polished endface shall be less than 50 μm.
---------------------- Page: 15 ----------------------
SIST EN IEC 61754-4:2022
– 10 – IEC 61754-4:2022 © IEC 2022
Table 4 – Grade characteristics for simplex PC plug connector
Dimensions
mm
Grade Remarks
A
Minimum Maximum
a
A See IEC 61755-3-1
a
B See IEC 61755-3-1
a
C See IEC 61755-3-1
a
D See IEC 61755-3-1
a b
A Grade not specified at this time
m
a b
B 2,497 2,500
m
a b
C 2,494 2,500
m
a
Add the grade number to the interface reference number.
b 1
Refer to future IEC 61755-6-1 for guidance .
Figure 2 is an example of a simplex adaptor connector interface. Table 5 gives dimensions of
the simplex adaptor connector interface and Table 6 gives the grade of the simplex adaptor
connector interface.
___________
1
Under preparation. Stage at the time of publication: IEC/CDM 61755-6-1:2021.
---------------------- Page: 16 ----------------------
SIST EN IEC 61754-4:2022
IEC 61754-4:2022 © IEC 2022 – 11 –
Figure 2 – Simplex adaptor connector interface
Table 5 – Dimensions of the simplex adaptor connector interface
Dimensions
Reference Remarks
Minimum Maximum
A See Table 6
B 4,39 mm 4,79 mm
D 4,9 mm 5,5 mm
H 6,9 mm 7,1 mm
I 0,4 mm 0,8 mm
J 5,51 mm 5,90 mm
K 0,06 mm 1,00 mm
L 1,9 mm 2,1 mm
O 2,0 mm 2,2 mm
P 9,0 mm 9,1 mm
R 7,4 mm 7,5 mm
S 1,0 mm 1,1 mm Radius
T 3,80 mm 4,04 mm
U 5,0 mm 5,3 mm
V 0,6 mm 1,6 mm
AA Angle, unit in degrees
27° 33°
AB 0,8 mm 1,0 mm
AC 0,4 mm 0,6 mm Radius
---------------------- Page: 17 ----------------------
SIST EN IEC 61754-4:2022
– 12 – IEC 61754-4:2022 © IEC 2022
Dimensions
Reference Remarks
Minimum Maximum
AD 0,7 mm 0,8 mm
AE 0,4 mm 0,6 mm
AI 2,7 mm 2,8 mm
a
BA 5,4 mm 5,6 mm
a
BB 10,8 mm 11,2 mm
a
The dotted line structure in Figure 2 is a groove-shape preventing interference when the latch is deformed. It
is optional.
Table 6 – Grade characteristics for simplex adaptor connector
Dimensions
mm
Grade Remarks
A
Minimum Maximum
a a b
Resilient sleeve
a
Add the grade number to the interface reference number.
b
The connector alignment feature is a resilient sleeve. The feature shall accept a pin
gauge shown in Figure 3 to the centre of the adaptor with a force of 2 N to 5,9 N under
the condition that another pin gauge is inserted into the feature from the other side.
The centre of the adaptor is defined by the right side position of dimension H.
Figure 3 is an example of a pin gauge for adaptor. Table 7 gives pin gauge dimensions.
Figure 3 – Pin gauge for adaptor
Table 7 – Pin gauge dimensions
Dimensions
Reference mm Remarks
Minimum Maximum
CK 2,498 5 2,499 5 Surface roughness:
grade N4 (0,2 μm radius)
CL 2,8 4,8
CN 7
Figure 4 is an example of a duplex PC plug connector interface. Table 8 gives dimensions of
the duplex PC plug connector interface and Table 9 gives the grade of the duplex PC plug
connector interface.
A chamfer or radius is allowed to a maximum depth of 1,8 mm from the ferrule endface.
---------------------- Page: 18 ----------------------
SIST EN IEC 61754-4:2022
IEC 61754-4:2022 © IEC 2022 – 13 –
Figure 4 – Duplex PC plug connector interface
---------------------- Page: 19 ----------------------
SIST EN IEC 61754-4:2022
– 14 – IEC 61754-4:2022 © IEC 2022
Table 8 – Dimensions of the duplex PC plug connector interface
Dimensions
Reference Remarks
Minimum Maximum
A See Table 9
B 4,8 mm 4,9 mm
C 6,8 mm 7,4 mm
D 4,9 mm 5,3 mm
E 6,7 mm 6,8 mm
F Angle, unit in degrees
19° 23°
G Angle, unit in degrees
25° 35°
a
H 7,15 mm 7,5 mm
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.