SIST EN 13677-1:2003
(Main)Reinforced thermoplastic moulding compounds - Specification for GMT - Part 1: Designation
Reinforced thermoplastic moulding compounds - Specification for GMT - Part 1: Designation
1.1 This part of prEN 13677 establishes a data block system for the designation of glass mat reinforced thermoplastic composite sheet (GMT).
1.2 The types of thermoplastic composite sheets are differentiated from each other by a classification system based on information about basic polymer parameters, fillers/reinforcement content and type, intended method of processing and/or manufacturing, specific characteristics and designatory properties.
1.3 This European Standard is applicable to glass fibre mat reinforced polypropylene sheet materials only.
It applies to materials ready for commercial use in the form of flat sheet or coil.
This European Standard does not apply to :
3 thermoplastic sheet moulding materials where the polymer is other than polypropylene or polypropylene alloy or a blend ;
3 the reinforcement is other than glass fibre.
1.4 It is not intended to imply that materials having the same designation give necessarily the same performance. This part of prEN 13677 does not provide engineering data, performance data or data on processing conditions which may be required to specify a material for a particular application and/or method of processing.
If such additional properties are required, when ever possible, they shall be determined in accordance with the test methods specified in Part 2 of this European Standard.
1.5 Whenever technical properties required in the Part 3 of this standard need to be indicated, this data block system is also the basis for it.
1.6 To ensure that the meanings of codes remain unambiguous and to avoid conflicts within the system, codes and abbreviations have been co-ordinated within the relevant ISO technical sub-committees.
Verstärkte Thermoplast-Formmassen - Spezifikation für GMT - Teil 1: Bezeichnung
Diese Europäische Norm legt ein Daten-Blocksystem zur Bezeichnung von Flacherzeugnissen aus glasmattenverstärkten, thermoplastischen Verbundwerkstoffen (GMT-Produkten) fest.
Die Arten der GMT Produkte werden voneinander mit Hilfe eines Klassifizierungssystems unterschieden, das auf Informationen über die Parameter der Basis Polymere, Anteil und Art des Füllstoffs bzw. der Verstärkung, das vorgesehene Verarbeitungs- und/oder Herstellungsverfahren, spezifische Merkmale und kennzeichnende Eigenschaften beruht.
Diese Europäische Norm gilt ausschließlich für glasmattenverstärkte Flacherzeugnisse aus Polypropylen.
Sie gilt für gebrauchsfertige Werkstoffe in Form flacher Tafeln oder Wickel.
Diese Europäische Norm gilt nicht für:
GMT Produkte, deren Polymer aus einem anderen Polymer als Polypropylen oder einem Poly-propylengemisch oder einer Mischung besteht;
andere Verstärkungen als Glasfaser.
Es soll nicht unterstellt werden, dass Werkstoffe mit gleicher Bezeichnung notwendigerweise gleiche Leistungsparameter aufweisen. In dieser Europäischen Norm werden keine Fertigungsunterlagen, Leistungsangaben oder Verarbeitungsbedingungen angegeben, die erforderlich sein können, um einen Werkstoff für eine bestimmte Anwendung und/oder eine bestimmte Verarbeitungsart festzulegen.
Wenn solche zusätzlichen Eigenschaften gefordert werden, müssen diese, soweit dies möglich ist, in Übereinstimmung mit den in Teil 2 dieser Europäischen Norm festgelegten Prüfverfahren bestimmt werden.
Wenn in Teil 3 der vorliegenden Norm geforderte technische Eigenschaften angegeben werden müssen, bildet dieses Daten-Blocksystem ebenfalls die Grundlage.
Um sicherzustellen, dass die Eindeutigkeit der Zeichen erhalten bleibt und um Widersprüche innerhalb des Systems zu vermeiden, müssen Zeichen und Kurzzeichen innerhalb der relevanten technischen Unterkomitees koordiniert werden.
Préimprégnés renforcés thermoplastiques - Spécifications des GMT - Partie 1: Désignation
1.1 La présente partie de la norme CEN....établit un systeme de blocs de donnéespor la désignation de feuille composite en polypropylene renforcé de mat de verre(GMT). 1.2 Les types de feuille composite en polypropylene se distinguent entre eux parun systeme de classification basé sur une information relative aux parametres dupolymere de base, a la teneur et au type de charge/renfort,a la méthode de traitement et/ou de fabrication prévue, aux caractéristiques spécifiques et aux caractéristiques de désignation.
Ojačani plastomerni materiali za oblikovanje - Specifikacije za s stekleno mato ojačane plastomere (GMT) – 1 del: Označevanje
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Verstärkte Thermoplast-Formmassen - Spezifikation für GMT - Teil 1: BezeichnungPréimprégnés renforcés thermoplastiques - Spécifications des GMT - Partie 1: DésignationReinforced thermoplastic moulding compounds - Specification for GMT - Part 1: Designation83.120Reinforced plasticsICS:Ta slovenski standard je istoveten z:EN 13677-1:2003SIST EN 13677-1:2003en01-julij-2003SIST EN 13677-1:2003SLOVENSKI
STANDARD
SIST EN 13677-1:2003
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13677-1February 2003ICS 83.120English versionReinforced thermoplastic moulding compounds - Specificationfor GMT - Part 1: DesignationPréimprégnés renforcés thermoplastiques - Spécificationsdes GMT - Partie 1: DésignationVerstärkte Thermoplast-Formmassen - Spezifikation fürGMT - Teil 1: BezeichnungThis European Standard was approved by CEN on 28 November 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and UnitedKingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13677-1:2003 ESIST EN 13677-1:2003
EN 13677-1:2003 (E)2ContentspageForeword.3Introduction.41Scope.52Normative references.53Designation system.63.1General.63.2Data block 1.73.3Data block 2.73.4Data block 3.83.5Data block 4.83.6Data block 5.114Examples for designations.12SIST EN 13677-1:2003
EN 13677-1:2003 (E)3ForewordThis document (EN 13677-1:2003) has been prepared by Technical Committee CEN/TC 249 "Plastics", thesecretariat of which is held by IBN.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by August 2003, and conflicting national standards shall be withdrawn at the latest byAugust 2003.EN 13677 consists of the following parts, under the general title, Reinforced thermoplastic moulding compounds –Specification for GMT.¾ Part 1: Designation¾ Part 2: Methods of test and general requirements¾ Part 3: Specific requirementsAccording to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal,Slovakia, Spain, Sweden, Switzerland and the United Kingdom.SIST EN 13677-1:2003
EN 13677-1:2003 (E)4IntroductionThis European Standard establishes a data-block system for the designation of glass mat reinforced thermoplasticsheet (GMT) using a format and coding system established by the International Standards Organisation (ISO)which is common to most fibre reinforced thermoset and thermoplastic moulding materials. The system is intendedto be applied only to materials ready for commercial use.The designation system is based on the premise that thermosets and long fibre reinforced thermo-plastics can bedivided into generic families using basic polymers, values of selected designatory properties and additionalqualitative information in order to describe a particular material as precisely as desired.The system is intended for the designation of a single material (or a small group of similar materials) within ageneric family.It is not intended to specify by this system the chemical composition or the volumetric recipe of the compound butto designate the material for identification purposes. It is the responsibility of the producer of the compound materialto provide the appropriate designation.The data-block system is also the basis for specification given in Parts 2 and 3 of this standard.SIST EN 13677-1:2003
EN 13677-1:2003 (E)51 ScopeThis European Standard establishes a data block system for the designation of glass mat reinforced thermoplasticcomposite sheet (GMT).The types of thermoplastic composite sheets are differentiated from each other by a classification system based oninformation about basic polymer parameters, fillers/reinforcement content and type, intended method of processingand/or manufacturing, specific characteristics and designatory properties.This European Standard is applicable to glass fibre mat reinforced polypropylene sheet materials only.It applies to materials ready for commercial use in the form of flat sheet or coil.This European Standard does not apply to:¾ thermoplastic sheet moulding materials where the polymer is other than polypropylene or polypropylene alloyor a blend ;¾ the reinforcement is other than glass fibre.It is not intended to imply that materials having the same designation give necessarily the same performance. ThisEuropean Standard does not provide engineering data, performance data or data on processing conditions whichmay be required to specify a material for a particular application and/or method of processing.If such additional properties are required, when ever possible, they shall be determined in accordance with the testmethods specified in Part 2 of this European Standard.Whenever technical properties required in the Part 3 of this standard need to be indicated, this data block system isalso the basis for it.To ensure that the meanings of codes remain unambiguous and to avoid conflicts within the system, codes andabbreviations have been co-ordinated within the relevant ISO technical sub-committees.2 Normative referencesThis European Standard incorporates by dated or undated reference, provisions from other publications. Thesenormative references are cited at the appropriate places in the text, and the publications are listed hereafter. Fordated references, subsequent amendments to or revisions of any of these publications apply to this EuropeanStandard only when incorporated in it by amendment or revision. For undated references the latest edition of thepublication referred to applies (including amendments).EN ISO 527-4, Plastics – Determination of tensile properties – Part 4 : Test conditions for isotropic and orthotopicfibre-reinforced plastic composites (ISO 527-4:1997).EN ISO 1043-1:2001, Plastics –Symbols and abbreviated terms – Part 1: Basic polymers and their specialcharacteristics (ISO 1043-1:2001).EN ISO 1043-2, Plastics – Symbols and abbreviated terms – Part2: Fillers and reinforcing materials (ISO 1043-2:2000).EN ISO 6603-2, Plastics – Determination of puncture impact behaviour of rigid plastics – Part 2: Instrumentedpuncture test (ISO 6603-2:2000).SIST EN 13677-1:2003
EN 13677-1:2003 (E)63 Designation system3.1 GeneralThis designation system for thermoplastic sheet moulding compound is based on the following standardisedpattern :DesignationDescription block(optional)Identity blockEuropeanStandardIndividual item blockNumberblockDatablock 1Datablock 2Datablock 3Datablock 4Datablock 5The designation consists of an optional description block, reading "GMT" and an identity block comprising theEuropean Standard number and an individual-item block. For unambiguous coding, the individual-item block issubdivided into 5 data blocks comprising the following information:¾ the first character of the individual item block shall be a hyphen. The data blocks shall be separated from eachother by commas;¾ if a data block is not used, this shall be indicated by "X" (=no indication) but only if another block follows;¾ for labelling purposes and if no other blocks follo
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.