This document specifies the test method for the determination of adhesive fracture energy of adhesively bonded plates of carbon fibre reinforced plastic (CFRP) and metal using a double cantilever beam (DCB) specimen. The test method is also applicable to bonded joints between metals and other composite materials, such as glass fibre reinforced plastics.

    • sale 15% off
    • Draft
      22 pages
      English language
    • sale 15% off
    • Standard
      22 pages
      English language
    • sale 15% off
    • Draft
      19 pages
      English language

This document specifies a method for the determination of the mass per unit area. It also specifies five
methods (Method A to Method E) for the determination of the fibre mass per unit area of moulding
compounds and prepregs. The five methods are as follows:
— Method A: Extraction by Soxhlet;
— Method B: Extraction by immersion in solvent in a beaker;
— Method C: Decomposition by loss ignition;
— Method D: Extraction by wet combustion;
— Method E: Method by calculation.
This document is ...
view more

    • sale 10% off
    • Standard
      23 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      19 pages
      English language
    • e-Library read for
      1 day

This document specifies accelerated moisture absorption properties and supersaturated conditioning by moisture for fibre-reinforced plastics) using sealed pressure vessel at higher temperature than 100 °C with saturated water vapour at used heating temperature. The purpose of this moisture absorbing procedure is to screen test specimens with moisture by mechanical or thermal properties. This document applies to carbon-fibre materials and their products with either thermoset or thermoplastic matr...view more

    • sale 15% off
    • Standard
      11 pages
      English language
    • sale 15% off
    • Draft
      13 pages
      English language

ISO 10350 identifies specific test procedures for the acquisition and presentation of comparable data
for certain basic properties of plastics. In general, each property is specified by a single experimental
value, although in certain cases properties are represented by two values obtained under different test
conditions or along different directions in the material. The properties included are those presented
conventionally in manufacturers' data sheets.
This document applies to reinforced...
view more

    • sale 10% off
    • Standard
      18 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      14 pages
      English language
    • e-Library read for
      1 day

This document specifies requirements for three types of textile-reinforced thermoplastics hoses and
hose assemblies of nominal size from 3,2 to 25. Each type is divided into two classes dependent on
electrical conductivity requirements.
They are suitable for use with:
— oil-based hydraulic fluids HH, HL, HM, HR and HV as defined in ISO 6743-4 at temperatures ranging
from −40 °C to +93 °C;
— water-based fluids HFC, HFAE, HFAS and HFB as defined in ISO 6743-4 at temperatures ranging
from 0 ...
view more

    • sale 10% off
    • Standard
      20 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      16 pages
      English language
    • e-Library read for
      1 day

This document specifies a method for the determination of the mass per unit area. It also specifies five methods (Method A to Method E) for the determination of the fibre mass per unit area of moulding compounds and prepregs. The five methods are as follows: — Method A: Extraction by Soxhlet; — Method B: Extraction by immersion in solvent in a beaker; — Method C: Decomposition by loss ignition; — Method D: Extraction by wet combustion; — Method E: Method by calculation. This document is applicab...view more

    • sale 15% off
    • Standard
      16 pages
      French language
    • sale 15% off
    • Standard
      15 pages
      English language
    • sale 15% off
    • Standard
      16 pages
      French language
    • sale 15% off
    • Draft
      15 pages
      English language

ISO 10350 identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value, although in certain cases properties are represented by two values obtained under different test conditions or along different directions in the material. The properties included are those presented conventionally in manufacturers' data sheets. This document applies to reinforced ther...view more

    • sale 15% off
    • Standard
      10 pages
      English language
    • sale 15% off
    • Standard
      10 pages
      French language
    • sale 15% off
    • Draft
      10 pages
      English language

This document provides general principles for the verification and assessment of the performance of concrete structures with the applications of different fibre-reinforced polymer (FRP) systems varying from internal FRP reinforcements/tendons, external FRP tendons, externally bonded FRP sheets/plates, to near-surface mounted FRP reinforcement. It can be used for the international harmonization of the design of un-reinforced, conventionally reinforced, and pre-stressed concrete structures with th...view more

    • sale 15% off
    • Standard
      7 pages
      English language

This document specifies a method using a shear test apparatus for measuring the in-plane shear stress/shear strain response, shear modulus and shear strength of continuous-fibre-reinforced plastic composite materials with fibre orientations of 0° and 0°/90°.
This method is applicable to thermoset and thermoplastic matrix laminates made from unidirectional layers/non-woven fabrics and/or fabrics including unidirectional fabrics, with the fibres oriented at 0° and 0°/90° to the specimen axis, whe...
view more

    • sale 10% off
    • Standard
      20 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      17 pages
      English language
    • e-Library read for
      1 day

This document specifies a method using a shear test apparatus for measuring the in-plane shear stress/shear strain response, shear modulus and shear strength of continuous-fibre-reinforced plastic composite materials with fibre orientations of 0° and 0°/90°.
This method is applicable to thermoset and thermoplastic matrix laminates made from unidirectional layers/non-woven fabrics and/or fabrics including unidirectional fabrics, with the fibres oriented at 0° and 0°/90° to the specimen axis, whe...
view more

    • sale 10% off
    • Standard
      20 pages
      English language
    • e-Library read for
      1 day
    • sale 10% off
    • Draft
      17 pages
      English language
    • e-Library read for
      1 day

This document specifies test methods applicable to unidirectional carbon fibre-reinforced polymer (CFRP) strips as external-bonded reinforcements on the concrete substrate. This document is applicable for the CFRP strips that: — consist of carbon fibre and thermoset resin; — are manufactured by pultrusion method; — have a higher carbon fibre fraction such as over 60 %; and — have a thickness within 3 mm. Also, the test pieces for determining tensile properties are cut down from CFRP strips along...view more

    • sale 15% off
    • Standard
      11 pages
      English language

This document specifies the test method for obtaining bending moment-curvature curves of fibre-reinforced cementitious composites (FRCCs) through four-point bending test of prism specimens. It is applicable to FRCCs that show separated multiple cracks under pure bending before maximum load.

    • sale 15% off
    • Standard
      11 pages
      English language

1.1 This document specifies a procedure for the initial qualification of composite materials in order to allow quality control, material selection and preliminary design to be undertaken. It provides a single procedure allowing quicker and lower cost qualification compared to multiple bi-lateral qualification against different bespoke user needs. This document focuses on developing B-basis design allowables. 1.2 The procedure comprises a standard qualification plan (SQP) that includes the minimu...view more

    • sale 15% off
    • Standard
      27 pages
      English language

This document specifies the apparatus, the reagents and the procedure to be used in conducting the neutral salt spray (NSS), acetic acid salt spray (AASS) and copper-accelerated acetic acid salt spray (CASS) tests for assessment of the galvanic corrosion resistance of joints and bonded structures between carbon fibre reinforced plastics (CFRPs) and metallic materials, with or without permanent or temporary insulation for the galvanic current.

    • sale 15% off
    • Standard
      19 pages
      English language

This European Standard specifies a method for determining the tensile properties of pultruded, unidirectional rods made from continuous fibre-reinforced plastic composites, in parallel to fibre direction.
It is applicable to pultruded rods which diameters are preferably ranging from 3 mm to 20 mm.
This method is suitable for use with continuous-fibre-reinforced plastic composites made from carbon fibres and glass fibres.
This method is suitable for use with all polymer matrix systems reinforc...
view more

    • sale 10% off
    • Standard
      22 pages
      English language
    • e-Library read for
      1 day

This document specifies a test method for evaluating flexural performance of fibre-reinforced cementitious composites (FRCCs) using derived parameters. These parameters are derived from the load-deflection curve obtained by testing a circular specimen supported on a concentric ring and loaded by another ring with a smaller diameter. The performance of FRCCs tested by this method is characterized for biaxial properties. This test method provides for the determination of first-cracking load and th...view more

    • sale 15% off
    • Standard
      13 pages
      English language

This document specifies a method for determining the tensile properties of pultruded, unidirectional rods made from continuous fibre-reinforced plastic composites, in parallel to fibre direction.
It is applicable to pultruded rods which diameters are preferably ranging from 3 mm to 20 mm.
This method is suitable for use with continuous-fibre-reinforced plastic composites made from carbon fibres and glass fibres.
This method is suitable for use with all polymer matrix systems reinforced with u...
view more

    • sale 10% off
    • Standard
      22 pages
      English language
    • e-Library read for
      1 day

This document specifies a method using a shear test apparatus for measuring the in-plane shear stress/shear strain response, shear modulus and shear strength of continuous-fibre-reinforced plastic composite materials with fibre orientations of 0° and 0°/90°. This method is applicable to thermoset and thermoplastic matrix laminates made from unidirectional layers/non-woven fabrics and/or fabrics including unidirectional fabrics, with the fibres oriented at 0° and 0°/90° to the specimen axis, wher...view more

    • sale 15% off
    • Standard
      14 pages
      French language
    • sale 15% off
    • Standard
      12 pages
      English language

This document specifies a flexural test method for determining the through-thickness (out-of-plane) tensile properties of laminated carbon fibre-reinforced plastic (CFRP) composites, including strength, fracture strain, and modulus. This document is applicable to unidirectional CFRP (UD-CFRP) laminates. In addition, the calculation of effective volume is also described due to size effects of the through-thickness tensile strength.

    • sale 15% off
    • Standard
      13 pages
      English language

This document specifies a procedure for determining the interlaminar strength, and modulus, by double beam shear (DBS) tests of fibre-reinforced plastic composites. The method is suitable for use with glass or carbon fibre-reinforced plastic composites with thermoset matrices, providing an acceptable interlaminar failure is obtained. This document only applies to laminate with a symmetrical and balanced lay‐up as it avoids bending/twisting or bending/extension coupling deformations (see 6.2). Th...view more

    • sale 15% off
    • Standard
      21 pages
      English language