SIST EN 6029:2017
(Main)Aerospace series - Rod-ends, adjustable, single fork with UNJ threaded shank min. engagement: 1,5 x thread diameter in corrosion resisting steel - Dimensions and loads - Inch series
Aerospace series - Rod-ends, adjustable, single fork with UNJ threaded shank min. engagement: 1,5 x thread diameter in corrosion resisting steel - Dimensions and loads - Inch series
This European Standard specifies the characteristics of adjustable rod ends in corrosion resisting steel,
inch series, consisting of:
a single fork ;
a UNJ threaded shank with ;
min. engagement 1,5 times thread diameter and
longitudinal groove for locking purposes.
These rod ends are intended for use with control rods or rods for aerospace structures.
They shall be used in the temperature range − 54 °C and 150 °C.
Luft- und Raumfahrt - Einstellbare Gabelköpfe, einfach, UNJ-Gewindeschaft, min. Einschraubtiefe 1,5 x Gewindedurchmesser, aus korrosionsbeständigem Stahl - Maße und Belastungen - Inch-Reihe
Série aérospatiale - Embouts réglables a chape simple a tige filetée UNJ, implantation min. : 1,5 x diamètre de filetage en acier résistant à la corrosion - Dimensions et charges - Série en inches
Aeronavtika - Končniki, nastavljivi, enostavni (enoročični), UNJ-navojne ročice z dolžino navoja min. 1,5 x premer navoja, iz korozijsko odpornega jekla - Mere in obremenitve - Colska izvedba
Ta evropski standard določa lastnosti nastavljivih končnikov iz korozijsko odpornega jekla,
colske izvedbe, sestavljenih iz:
ene ročice;
UNJ-navojne ročice z;
dolžino navoja min. 1,5-krat premer navoja in
vzdolžnim utorom za zaklepanje.
Končniki so namenjeni za uporabo s kontrolnimi ali drugimi ročicami v letalstvu.
Uporabljati jih je treba v temperaturnem razponu −54 °C in 150 °C.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 6029:2017
01-marec-2017
Aeronavtika - Končniki, nastavljivi, enostavni (enoročični), UNJ-navojne ročice z
dolžino navoja min. 1,5 x premer navoja, iz korozijsko odpornega jekla - Mere in
obremenitve - Colska izvedba
Aerospace series - Rod-ends, adjustable, single fork with UNJ threaded shank min.
engagement: 1,5 x thread diameter in corrosion resisting steel - Dimensions and loads -
Inch series
Luft- und Raumfahrt - Einstellbare Gabelköpfe, einfach, UNJ-Gewindeschaft, min.
Einschraubtiefe 1,5 x Gewindedurchmesser, aus korrosionsbeständigem Stahl - Maße
und Belastungen - Inch-Reihe
Série aérospatiale - Embouts réglables a chape simple a tige filetée UNJ, implantation
min. : 1,5 x diamètre de filetage en acier résistant à la corrosion - Dimensions et charges
- Série en inches
Ta slovenski standard je istoveten z: EN 6029:2017
ICS:
49.035 Sestavni deli za letalsko in Components for aerospace
vesoljsko gradnjo construction
SIST EN 6029:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 6029:2017
---------------------- Page: 2 ----------------------
SIST EN 6029:2017
EN 6029
EUROPEAN STANDARD
NORME EUROPÉENNE
January 2017
EUROPÄISCHE NORM
ICS 49.035
English Version
Aerospace series - Rod-ends, adjustable, single fork with
UNJ threaded shank min. engagement: 1,5 x thread
diameter in corrosion resisting steel - Dimensions and
loads - Inch series
Série aérospatiale - Embouts réglables a chape simple a Luft- und Raumfahrt - Einstellbare Gabelköpfe, einfach,
tige filetée UNJ, implantation min. : 1,5 x diamètre de UNJ-Gewindeschaft, min. Einschraubtiefe 1,5 x
filetage en acier résistant à la corrosion - Dimensions et Gewindedurchmesser, aus korrosionsbeständigem
charges - Série en inches Stahl - Maße und Belastungen - Inch-Reihe
This European Standard was approved by CEN on 20 August 2016.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATIO N
EUROPÄISCHES KOMITEE FÜR NORMUN G
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 6029:2017 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 6029:2017
EN 6029:2017 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Required characteristics . 4
4 Designation. 9
5 Marking . 9
6 Technical specification . 9
Annex A (informative) Standard evolution form . 10
2
---------------------- Page: 4 ----------------------
SIST EN 6029:2017
EN 6029:2017 (E)
European foreword
This document (EN 6029:2017) has been prepared by the Aerospace and Defence Industries
Association of Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
ASD, prior to its presentation to CEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by July 2017, and conflicting national standards shall be
withdrawn at the latest by July 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
3
---------------------- Page: 5 ----------------------
SIST EN 6029:2017
EN 6029:2017 (E)
1 Scope
This European Standard specifies the characteristics of adjustable rod ends in corrosion resisting steel,
inch series, consisting of:
a single fork ;
a UNJ threaded shank with ;
min. engagement 1,5 times thread diameter and
longitudinal groove for locking purposes.
These rod ends are intended for use with control rods or rods for aerospace structures.
They shall be used in the temperature range − 54 °C and 150 °C.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced docu
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.