SIST EN 3707:2012

Aerospace series - Headless threaded plugs - Installation holes

This European Standard specifies the dimensions of the installation holes for headless plugs to EN 3706 for sealing drilled fluid systems. The maximum operating temperature is 200 °C.

Luft- und Raumfahrt - Verschlussschraube ohne Kopf - Einbaulöcher

Diese Europäische Norm legt die Maße der Einbaulöcher für Verschlussschrauben ohne Kopf nach EN 3706 zur Abdichtung angebohrter Fluidanlagen fest. Die höchste Betriebstemperatur liegt bei 200 °C.

Série aérospatiale - Bouchons filetés, sans tête - Trous d’implantation

La présente Norme Européenne spécifie les dimensions des trous d’implantation des bouchons filetés, sans tête, selon l’EN 3706 pour l’étanchéité des systèmes de fluides forés. La température maximale de fonctionnement est de 200 °C.

Aeronavtika - Brezglava navojna zapirala - Luknje za pritrjevanje

Ta evropski standard določa mere lukenj za pritrjevanje brezglavih zapiral v zvezi s standardom EN 3706 za tesnjenje sistemov vrtalne tekočine. Največja dovoljena obratovalna temperatura je 200 °C.

General Information

• Status: Published
• Publication Date: 05-Jul-2012
• ICS: 49.030.20 - Bolts, screws, studs
• Technical Committee: I13 - Imaginarni 13
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 18-Jun-2012
• Due Date: 23-Aug-2012
• Completion Date: 06-Jul-2012
• Ref Project: EN 3707:2012 - Aerospace series - Headless threaded plugs - Installation holes

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aeronavtika - Brezglava navojna zapirala - Luknje za pritrjevanjeLuft- und Raumfahrt - Verschlussschraube ohne Kopf - EinbaulöcherSérie aérospatiale - Bouchons filetés, sans tête - Trous d’implantationAerospace series - Headless threaded plugs - Installation holes49.030.20Sorniki, vijaki, stebelni vijakiBolts, screws, studsICS:Ta slovenski standard je istoveten z:EN 3707:2012SIST EN 3707:2012en,de01-september-2012SIST EN 3707:2012SLOVENSKI
STANDARD



SIST EN 3707:2012



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 3707
March 2012 ICS 49.030.20 English Version
Aerospace series - Headless threaded plugs - Installation holes Série aérospatiale - Bouchons filetés, sans tête - Trous d'implantation
Luft- und Raumfahrt - Verschlussschraube ohne Kopf - Einbaulöcher This European Standard was approved by CEN on 23 December 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3707:2012: ESIST EN 3707:2012



EN 3707:2012 (E) 2 Contents Page Foreword .31 Scope .42 Normative references .43 Required characteristics .43.1 Configuration — Dimensions — Tolerances .43.2 Profile trimming .44 Installation .54.1 Hole dimension .54.2 Special location conditions .65 Designation .76 Indications on drawings — Examples .8 SIST EN 3707:2012



EN 3707:2012 (E) 3 Foreword This document (EN 3707:2012) has been prepared by the Aerospace and Defence Industries Association of Eur
...