Aerospace series - Headless threaded plugs - Installation holes

This European Standard specifies the dimensions of the installation holes for headless plugs to EN 3706 for
sealing drilled fluid systems. The maximum operating temperature is 200 °C.

Luft- und Raumfahrt - Verschlussschraube ohne Kopf - Einbaulöcher

Diese Europäische Norm legt die Maße der Einbaulöcher für Verschlussschrauben ohne Kopf nach EN 3706 zur Abdichtung angebohrter Fluidanlagen fest. Die höchste Betriebstemperatur liegt bei 200 °C.

Série aérospatiale - Bouchons filetés, sans tête - Trous d’implantation

La présente Norme Européenne spécifie les dimensions des trous d’implantation des bouchons filetés, sans tête, selon l’EN 3706 pour l’étanchéité des systèmes de fluides forés. La température maximale de fonctionnement est de 200 °C.

Aeronavtika - Brezglava navojna zapirala - Luknje za pritrjevanje

Ta evropski standard določa mere lukenj za pritrjevanje brezglavih zapiral v zvezi s standardom EN 3706 za tesnjenje sistemov vrtalne tekočine. Največja dovoljena obratovalna temperatura je 200 °C.

General Information

Publication Date
Withdrawal Date
Technical Committee
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date

Buy Standard

EN 3707:2012
English language
8 pages
sale 10% off
sale 10% off
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aeronavtika - Brezglava navojna zapirala - Luknje za pritrjevanjeLuft- und Raumfahrt - Verschlussschraube ohne Kopf - EinbaulöcherSérie aérospatiale - Bouchons filetés, sans tête - Trous d’implantationAerospace series - Headless threaded plugs - Installation holes49.030.20Sorniki, vijaki, stebelni vijakiBolts, screws, studsICS:Ta slovenski standard je istoveten z:EN 3707:2012SIST EN 3707:2012en,de01-september-2012SIST EN 3707:2012SLOVENSKI

SIST EN 3707:2012

EN 3707
March 2012 ICS 49.030.20 English Version
Aerospace series - Headless threaded plugs - Installation holes Série aérospatiale - Bouchons filetés, sans tête - Trous d'implantation
Luft- und Raumfahrt - Verschlussschraube ohne Kopf - Einbaulöcher This European Standard was approved by CEN on 23 December 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3707:2012: ESIST EN 3707:2012

EN 3707:2012 (E) 2 Contents Page Foreword .31 Scope .42 Normative references .43 Required characteristics .43.1 Configuration — Dimensions — Tolerances .43.2 Profile trimming .44 Installation .54.1 Hole dimension .54.2 Special location conditions .65 Designation .76 Indications on drawings — Examples .8 SIST EN 3707:2012

EN 3707:2012 (E) 3 Foreword This document (EN 3707:2012) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Septembre 2012, and conflicting national standards shall be withdrawn at the latest by September 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countrie

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.