Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 1: Sampling (ISO 11127-1:2020)

This document specifies a method for the sampling of non-metallic blast-cleaning abrasives from
consignments and for the subdivision of the sample into quantities suitable for undertaking the
appropriate test methods specified in ISO 11127-2, ISO 11127-3, ISO 11127-4, ISO 11127-5, ISO 11127-6
and ISO 11127-7.
This document is a part of the ISO 11127 series dealing with the sampling and testing of non-metallic
abrasives for blast-cleaning.
The types of non-metallic abrasive and requirements for each are contained in the ISO 11126 series.
The ISO 11126 and ISO 11127 series have been drafted as a coherent set of International Standards on
non-metallic blast-cleaning abrasives. Information on all parts of both series is given in Annex B.

Vorbereitung von Stahloberflächen vor dem Auftragen von Beschichtungsstoffen - Prüfverfahren für nichtmetallische Strahlmittel - Teil 1: Probenahme (ISO 11127-1:2020)

Dieses Dokument legt ein Verfahren zur Probenahme nichtmetallischer Strahlmittel aus Lieferungen und die Unterteilung der Probe in geeignete Mengen zur Durchführung der in ISO 11127 2, ISO 11127 3, ISO 11127 4, ISO 11127 5, ISO 11127 6 und ISO 11127 7 beschriebenen Prüfungen fest.
Dieses Dokument ist ein Teil der Normenreihe ISO 11127, welche die Probenahme und die Prüfung von nichtmetallischen Strahlmitteln behandelt.
Die verschiedenen Arten nichtmetallischer Strahlmittel und Anforderungen an diese sind in der Normenreihe ISO 11126 enthalten.
Die Normenreihen ISO 11126 und ISO 11127 wurden als zusammengehöriger Satz von Internationalen Normen über nichtmetallische Strahlmittel erarbeitet. Angaben zu allen Teilen der beiden Normenreihen sind im Anhang B enthalten.

Préparation des subjectiles d'acier avant application de peintures et de produits assimilés - Méthodes d'essai pour abrasifs non métalliques destinés à la préparation par projection - Partie 1: Échantillonnage (ISO 11127-1:2020)

Le présent document spécifie une méthode d'échantillonnage de livraison d'abrasifs non métalliques destinés à la préparation par projection et de fractionnement de l'échantillon en quantités appropriées à la mise en œuvre des méthodes d'essai spécifiées dans l'ISO 11127‑2, l'ISO 11127‑3, l'ISO 11127‑4, l'ISO 11127‑5, l'ISO 11127‑6 et l'ISO 11127‑7.
Ce document fait partie de la série de normes ISO 11127, qui traite de l'échantillonnage et des essais des abrasifs non métalliques destinés à la préparation par projection.
Les différents types d'abrasifs non métalliques et leurs exigences respectives figurent dans la série de normes ISO 11126.
Les séries ISO 11126 et ISO 11127 ont été élaborées comme un ensemble cohérent de Normes internationales sur les abrasifs non métalliques destinés à la préparation par projection. Des informations sur toutes les parties des deux séries sont données dans l'Annexe B.

Priprava jeklenih podlag pred nanašanjem barv in sorodnih premazov - Preskusne metode za nekovinske granulate za peskanje - 1. del: Vzorčenje (ISO 11127-1:2021)

General Information

Status
Published
Public Enquiry End Date
03-Nov-2019
Publication Date
08-Mar-2021
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
04-Mar-2021
Due Date
09-May-2021
Completion Date
09-Mar-2021

Relations

Buy Standard

Standard
EN ISO 11127-1:2021
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Draft
prEN ISO 11127-1:2019
English language
9 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 11127-1:2021
01-april-2021
Nadomešča:
SIST EN ISO 11127-1:2012
Priprava jeklenih podlag pred nanašanjem barv in sorodnih premazov - Preskusne
metode za nekovinske granulate za peskanje - 1. del: Vzorčenje (ISO 11127-1:2021)
Preparation of steel substrates before application of paints and related products - Test
methods for non-metallic blast-cleaning abrasives - Part 1: Sampling (ISO 11127-1:2020)
Vorbereitung von Stahloberflächen vor dem Auftragen von Beschichtungsstoffen -
Prüfverfahren für nichtmetallische Strahlmittel - Teil 1: Probenahme (ISO 11127-1:2020)
Préparation des subjectiles d'acier avant application de peintures et de produits
assimilés - Méthodes d'essai pour abrasifs non métalliques destinés à la préparation par
projection - Partie 1: Échantillonnage (ISO 11127-1:2020)
Ta slovenski standard je istoveten z: EN ISO 11127-1:2021
ICS:
25.220.10 Priprava površine Surface preparation
SIST EN ISO 11127-1:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 11127-1:2021

---------------------- Page: 2 ----------------------
SIST EN ISO 11127-1:2021


EN ISO 11127-1
EUROPEAN STANDARD

NORME EUROPÉENNE

February 2021
EUROPÄISCHE NORM
ICS 25.220.10 Supersedes EN ISO 11127-1:2011
English Version

Preparation of steel substrates before application of paints
and related products - Test methods for non-metallic
blast-cleaning abrasives - Part 1: Sampling (ISO 11127-
1:2020)
Préparation des subjectiles d'acier avant application de Vorbereitung von Stahloberflächen vor dem Auftragen
peintures et de produits assimilés - Méthodes d'essai von Beschichtungsstoffen - Prüfverfahren für
pour abrasifs non métalliques destinés à la préparation nichtmetallische Strahlmittel - Teil 1: Probenahme (ISO
par projection - Partie 1: Échantillonnage (ISO 11127- 11127-1:2020)
1:2020)
This European Standard was approved by CEN on 9 October 2020.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11127-1:2021 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 11127-1:2021
EN ISO 11127-1:2021 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 11127-1:2021
EN ISO 11127-1:2021 (E)
European foreword
This document (EN ISO 11127-1:2021) has been prepared by Technical Committee ISO/TC 35 "Paints
and varnishes" in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2021, and conflicting national standards shall
be withdrawn at the latest by August 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11127-1:2011.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 11127-1:2020 has been approved by CEN as EN ISO 11127-1:2021 without any
modification.


3

---------------------- Page: 5 ----------------------
SIST EN ISO 11127-1:2021

---------------------- Page: 6 ----------------------
SIST EN ISO 11127-1:2021
INTERNATIONAL ISO
STANDARD 11127-1
Third edition
2020-10
Preparation of steel substrates before
application of paints and related
products — Test methods for non-
metallic blast-cleaning abrasives —
Part 1:
Sampling
Préparation des subjectiles d'acier avant application de peintures
et de produits assimilés — Méthodes d'essai pour abrasifs non
métalliques destinés à la préparation par projection —
Partie 1: Échantillonnage
Reference number
ISO 11127-1:2020(E)
©
ISO 2020

---------------------- Page: 7 ----------------------
SIST EN ISO 11127-1:2021
ISO 11127-1:2020(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved

---------------------- Page: 8 ----------------------
SIST EN ISO 11127-1:2021
ISO 11127-1:2020(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Apparatus . 2
5 Procedure. 2
5.1 Sampling of consignments . 2
5.2 Preparation of the mixed sample . 2
5.3 Reduction of sample size . 2
5.4 Test sample . 3
6 Sample identification . 3
Annex A (informative) Guidance on sampling from stockpiles or transportation units .5
Annex B (informative) International Standards for non-metallic blast-cleaning abrasives .6
Bibliography . 7
© ISO 2020 – All rights reserved iii

---------------------- Page: 9 ----------------------
SIST EN ISO 11127-1:2021
ISO 11127-1:2020(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 35, Pain
...

SLOVENSKI STANDARD
oSIST prEN ISO 11127-1:2019
01-oktober-2019
Priprava jeklenih podlag pred nanašanjem barv in sorodnih premazov - Preskusne
metode za nekovinske granulate za peskanje - 1. del: Vzorčenje (ISO/DIS
11127:2019)
Preparation of steel substrates before application of paints and related products - Test
methods for non-metallic blast-cleaning abrasives - Part 1: Sampling (ISO/DIS 11127-
1:2019)
Vorbereitung von Stahloberflächen vor dem Auftragen von Beschichtungsstoffen -
Prüfverfahren für nichtmetallische Strahlmittel - Teil 1: Probenahme (ISO 11127-1:2019)
Préparation des subjectiles d'acier avant application de peintures et de produits
assimilés - Méthodes d'essai pour abrasifs non métalliques destinés à la préparation par
projection - Partie 1: Échantillonnage (ISO/DIS 11127-1:2019)
Ta slovenski standard je istoveten z: prEN ISO 11127-1 rev
ICS:
25.220.10 Priprava površine Surface preparation
oSIST prEN ISO 11127-1:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 11127-1:2019

---------------------- Page: 2 ----------------------
oSIST prEN ISO 11127-1:2019
DRAFT INTERNATIONAL STANDARD
ISO/DIS 11127-1
ISO/TC 35/SC 12 Secretariat: BSI
Voting begins on: Voting terminates on:
2019-09-10 2019-12-03
Preparation of steel substrates before application of paints
and related products — Test methods for non-metallic
blast-cleaning abrasives —
Part 1:
Sampling
Préparation des subjectiles d'acier avant application de peintures et de produits assimilés — Méthodes
d'essai pour abrasifs non métalliques destinés à la préparation par projection —
Partie 1: Échantillonnage
ICS: 25.220.10
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 11127-1:2019(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2019

---------------------- Page: 3 ----------------------
oSIST prEN ISO 11127-1:2019
ISO/DIS 11127-1:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 11127-1:2019
ISO/DIS 11127-1:2019(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Apparatus . 2
5 Procedure. 2
5.1 Sampling of consignments . 2
5.2 Preparation of the mixed sample . 2
5.3 Reduction of sample size . 2
5.4 Test sample . 2
6 Sample identification . 3
Annex A (informative) Guidance on sampling from stockpiles or transportation units .4
Annex B (informative) International Standards for non-metallic blast-cleaning abrasives .5
© ISO 2019 – All rights reserved iii

---------------------- Page: 5 ----------------------
oSIST prEN ISO 11127-1:2019
ISO/DIS 11127-1:2019(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International
Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies
casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 11127-1 was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee
SC 12, Preparation of steel substrates before application of paints and related products.
This third edition cancels and replaces the second edition (ISO 11127-1:2011)
The main changes are as follows:
— Normative References section has been added and subsequent clauses renumbered
— Annex B has been technically and editorially revised
A list of all parts in the ISO 11127 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2019 – All rights reserved

---------------------- Page: 6 ----------------------
oSIST prEN ISO 11127-1:2019
DRAFT INTERNATIONAL STANDARD ISO/DIS 11127-1:2019(E)
Preparation of steel substrates before application of paints
and related products — Test methods for non-metallic
blast-cleaning abrasives —
Part 1:
Sampling
1 Scope
This is one of a number of parts of ISO 11127 dealing with the sampling and testing of non-metallic
abrasives for blast-cleaning.
The types of non-metallic abrasive and requirements on each are contained in ISO 11126.
The ISO 11126 and ISO 11127 series have been drafted as a coherent set of International Standards on
non-metallic blast-cleaning abrasives. Information on all parts of both series is given in Annex B.
This part of ISO 11127 specifies a method for the sampli
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.