Optical fibres - Part 1-32: Measurement methods and test procedures - Coating strippability (IEC 60793-1-32:2010)

This part of IEC 60793 is intended primarily for testing either fibres as produced by a fibre manufacturer or subsequently overcoated (tight buffered) using various polymers. The test can be performed either on fibres as produced or after exposure to various environments. This test applies to A1, A2, A3, B and C fibres. The object of this standard is to establish uniform requirements for the mechanical characteristic - coating strippability. This test quantifies the force required to mechanically remove the protective coating from optical fibres along their longitudinal axis. This test is not intended as a means to maximize fibre strength after the coating is removed nor is it intended to specify the best conditions for field stripping of optical fibres. This test is designed for optical fibres having polymeric coatings with nominal outer diameters in the range of 240 μm to 900 μm. Application of this method to fibres with outer coating diameters outside the range of 230 μm to 930 μm is not recommended. Warning - Fibres can fracture while being stripped and pierce skin and eyes. Use of protective eyewear is recommended.

Lichtwellenleiter - Teil 1-32: Messmethoden und Prüfverfahren - Absetzbarkeit der Beschichtung (IEC 60793-1-32:2010)

Fibres optiques - Partie 1-32 - Méthodes de mesure et procédures d'essai - dénudabilité du revêtement (CEI 60793-1-32:2010)

La CEI 60793-1-32:2010 est destinée principalement aux essais des fibres, dès leur production par un fabricant de fibres, ou après revêtement ultérieur (revêtement protecteur serré) au moyen de divers polymères. L'essai peut être effectué soit sur des fibres issues de production, soit après exposition à divers environnements. Le présent essai s'applique aux fibres de type A1, A2, A3, B et C. Cette édition a été modifiée pour inclure les pratiques utilisées actuellement sur le marché.
Cette publication contient des couleurs qui sont considérés comme étant utile pour une bonne compréhension de son contenu.

Optična vlakna - 1-32. del: Metode merjenja in preskusni postopki - Lupljivost prevleke (IEC 60793-1-32:2010)

Ta del IEC 60793 je namenjen predvsem preskušanju bodisi vlaken, kot jih proizvaja proizvajalec vlaken ali naknadno prevlečenih (močno puferiranih) z uporabo različnih polimerov. Preskus se lahko izvede bodisi na vlaknih, kot so proizvedena, bodisi po njihovi izpostavljenosti različnim okoljem. Preskus velja za vlakna tipov A1, A2, A3, B in C. Cilj tega standarda je vzpostaviti enotne zahteve za mehansko značilnost – lupljivost prevleke. Ta preskus količino določa s silo, potrebno za mehansko odstranitev varovalne prevleke iz optičnih vlaken po njihovi vzdolžni osi. Ta preskus ni namenjen za sredstvo maksimiranja moči vlakna po tem, ko je prevleka odstranjena niti ni namenjen temu, da opredeljuje najboljše pogoje za zaščito optičnih vlaken na terenu. Ta preskus je zasnovan za optična vlakna, ki imajo polimerne prevleke z nazivnimi zunanjimi premeri v razponu od 240 μm do 900 μm. Uporaba te metode za vlakna, ki imajo zunanji premer prevleke zunaj razpona med 230 μm do 930 μm se ne priporoča. Opozorilo – vlakna se med zaščito lahko lomijo in predrejo kožo ali oči. Priporoča se uporaba zaščitnih očal.

General Information

Status
Withdrawn
Publication Date
13-Oct-2010
Withdrawal Date
16-Jan-2022
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
13-Jan-2022
Due Date
05-Feb-2022
Completion Date
17-Jan-2022

Relations

Buy Standard

Standard
EN 60793-1-32:2010 - BARVE
English language
13 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60793-1-32:2010
01-november-2010
1DGRPHãþD
SIST EN 60793-1-32:2004
2SWLþQDYODNQDGHO0HWRGHPHUMHQMDLQSUHVNXVQLSRVWRSNL/XSOMLYRVW
SUHYOHNH ,(&
Optical fibres - Part 1-32: Measurement methods and test procedures - Coating
strippability (IEC 60793-1-32:2010)
Lichtwellenleiter - Teil 1-32: Messmethoden und Prüfverfahren - Absetzbarkeit der
Beschichtung (IEC 60793-1-32:2010)
Fibres optiques - Partie 1-32 - Méthodes de mesure et procédures d'essai - dénudabilité
du revêtement (CEI 60793-1-32:2010)
Ta slovenski standard je istoveten z: EN 60793-1-32:2010
ICS:
33.180.10 2SWLþQD YODNQDLQNDEOL Fibres and cables
SIST EN 60793-1-32:2010 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60793-1-32:2010

---------------------- Page: 2 ----------------------

SIST EN 60793-1-32:2010

EUROPEAN STANDARD
EN 60793-1-32

NORME EUROPÉENNE
October 2010
EUROPÄISCHE NORM

ICS 33.180.10 Supersedes EN 60793-1-32:2003


English version


Optical fibres -
Part 1-32: Measurement methods and test procedures -
Coating strippability
(IEC 60793-1-32:2010)


Fibres optiques -  Lichtwellenleiter -
Partie 1-32 - Méthodes de mesure Teil 1-32: Messmethoden
et procédures d'essai - und Prüfverfahren -
dénudabilité du revêtement Absetzbarkeit der Beschichtung
(CEI 60793-1-32:2010) (IEC 60793-1-32:2010)




This European Standard was approved by CENELEC on 2010-09-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2010 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60793-1-32:2010 E

---------------------- Page: 3 ----------------------

SIST EN 60793-1-32:2010
EN 60793-1-32:2010 - 2 -
Foreword
The text of document 86A/1273/FDIS, future edition 2 of IEC 60793-1-32, prepared by SC 86A, Fibres
and cables, of IEC TC 86, Fibre optics, was submitted to the IEC-CENELEC parallel vote and was
approved by CENELEC as EN 60793-1-32 on 2010-09-01.
This European Standard supersedes EN 60793-1-32:2003.
This edition has been modified to include current practices in the market place.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2011-06-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2013-09-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60793-1-32:2010 was approved by CENELEC as a European
Standard without any modification.
__________

---------------------- Page: 4 ----------------------

SIST EN 60793-1-32:2010
- 3 - EN 60793-1-32:2010
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

IEC 60793-1 Series Optical fibres - EN 60793-1 Series
Measurement methods and test procedures

---------------------- Page: 5 ----------------------

SIST EN 60793-1-32:2010

---------------------- Page: 6 ----------------------

SIST EN 60793-1-32:2010

IEC 60793-1-32
®
Edition 2.0 2010-05
INTERNATIONAL
STANDARD

colour
inside

Optical fibres –
Part 1-32: Measurement methods and test procedures – Coating strippability


INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
K
ICS 33.180.10 ISBN 978-2-88910-917-3
® Registered trademark of the International Electrotechnical Commission

---------------------- Page: 7 ----------------------

SIST EN 60793-1-32:2010
– 2 – 60793-1-32 © IEC:2010(E)
CONTENTS
FOREWORD.3
1 Scope.5
2 Normative references .5
3 Apparatus.5
3.1 Tensile equipment .5
3.2 Load cell .6
3.3 Transducer amplifier.6
3.4 Stripping tool.6
3.5 Fibre guide.6
4 Specimen preparation.7
4.1 Representative sample.7
4.2 Strip length.7
5 Procedure .7
5.1 Introduction .7
5.2 Stripping rate .7
5.3 Preconditioning .8
5.4 Calibrating the transducer amplifier .8
5.5 Loading the test specimen.8
5.6 Stripping the coating .8
6 Calculations .8
6.1 Calculation of the reported value for a specimen .8
6.2 Calculation for the value of a piece.8
6.3 Approach 1 – Average strip force .8
6.4 Approach 2 – Peak strip force .9
7 Documentation .9
8 Specification information .10

Figure 1 – Length of fibre to be stripped .7
Figure 2 – Example of test arrangement .9

---------------------- Page: 8 ----------------------

SIST EN 60793-1-32:2010
60793-1-32 © IEC:2010(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

OPTICAL FIBRES –

Part 1-32: Measurement methods and test procedures –
Coating strippability


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60793-1-32 has been prepared by subcommittee 86A: Fibres and
cables, of IEC technical committee 86: Fibre optics.
This second edition cancels and replaces the first edition published in 2001 and constitutes a
technical revision.
This edition has been modified to include current practices in the market place.

---------------------- Page: 9 ----------------------

SIST EN 60793-1-32:2010
– 4 – 60793-1-32 © IEC:2010(E)
The text of this standard is based on the following documents:
CDV Report on voting
86A/1273/CDV 86A/1310/RVC

Full informat
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.