SIST EN 3201:2008
(Main)Aerospace series - Holes for metric threaded fasteners - Design standard
Aerospace series - Holes for metric threaded fasteners - Design standard
This standard provides particulars of hole sizes, chamfer dimensions and positional tolerances to suit metric threaded fasteners with nominal diameters of 3 mm to 20 mm.
Luft- und Raumfahrt - Durchgangslöcher für metrische Schrauben - Konstruktionsnorm
Diese Norm enthält Einzelheiten von Lochgrößen, Fasenmaßen und Lagetoleranzen, die für Verbindungs-elemente mit metrischem Gewinde mit einem Nenndurchmesser von 3 mm bis 20 mm geeignet sind.
Série aérospatiale - Trous pour éléments de fixation filetés mériques - Norme de conception
Aeronavtika - Luknje za vijake z metrskim navojem - Standard za projektiranje
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aerospace series - Holes for metric threaded fasteners - Design standardAeronavtika - Luknje za vijake z metrskim navojem - Standard za projektiranjeSérie aérospatiale - Trous pour éléments de fixation filetés mériques - Norme de conceptionLuft- und Raumfahrt - Durchgangslöcher für metrische Schrauben - Konstruktionsnorm49.030.01Vezni elementi na splošnoFasteners in generalICS:SIST EN 3201:2008enTa slovenski standard je istoveten z:EN 3201:200801-julij-2008SIST EN 3201:2008SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 3201April 2008ICS 49.030.01 English VersionAerospace series - Holes for metric threaded fasteners - DesignstandardSérie aérospatiale - Trous pour éléments de fixation filetésmériques - Norme de conceptionLuft- und Raumfahrt - Durchgangslöcher für metrischeSchrauben - KonstruktionsnormThis European Standard was approved by CEN on 3 November 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 3201:2008: E
EN 3201:2008 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Hole characteristics.4 3 Holes for clearance applications.4 4 Positional tolerance's for clearance applications.6 5 Holes for close clearance applications.6 6 Positional tolerance for close clearance applications.7 7 Holes for fitted applications.8 8 Positional tolerance for fitted applications.9 9 Examples of positional tolerance to be used in clearance applications.10
EN 3201:2008 (E) 3 Foreword This document (EN 3201:2008) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2008, and conflicting national standards shall be withdrawn at the latest by October 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.