iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 60168:1997/A2:2002

(Amendment)

Tests on indoor and outdoor post insulators of ceramic material or glass for systems with nominal voltages greater than 1 kV

Tests on indoor and outdoor post insulators of ceramic material or glass for systems with nominal voltages greater than 1 kV

EN following parallel vote

Prüfungen an Innenraum- und Freiluft-Stützisolatoren aus keramischem Werkstoff oder Glas für Systeme mit Nennspannungen über 1 kV

Essais des supports isolants d'intérieur et d'extérieur, en matière céramique ou en verre, destinés à des installations de tension nominale supérieure à 1 kV

Tests on indoor and outdoor post insulators of ceramic material or glass for systems with nominal voltages greater than 1 kV - Amendment A2 (IEC 60168:1994/A2:2000)

General Information

Status
Published
Publication Date
30-Jun-2002
ICS
29.080.10 - Insulators
Technical Committee
IZL - Insulators
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Jul-2002
Due Date
01-Jul-2002
Completion Date
01-Jul-2002
Ref Project
EN 60168:1994/A2:2000 - Tests on indoor and outdoor post insulators of ceramic material or glass for systems with nominal voltages greater than 1 kV

Relations

Amends
SIST EN 60168:1997 - Tests on indoor and outdoor post insulators of ceramic material or glass for systems with nominal voltages greater than 1 kV
Effective Date
28-Jan-2023
Amends
SIST EN 60168:1997 - Tests on indoor and outdoor post insulators of ceramic material or glass for systems with nominal voltages greater than 1 kV
Effective Date
21-Sep-2010

Buy Standard

EN 60168:1997/A2:2002EN 60168:1997/A2:2002
PreviousNext
Amendment
EN 60168:1997/A2:2002
English language
4 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60168:1997/A2:2002
01-julij-2002
Tests on indoor and outdoor post insulators of ceramic material or glass for
systems with nominal voltages greater than 1 kV - Amendment A2 (IEC
60168:1994/A2:2000)
Tests on indoor and outdoor post insulators of ceramic material or glass for systems with
nominal voltages greater than 1 kV
Prüfungen an Innenraum- und Freiluft-Stützisolatoren aus keramischem Werkstoff oder
Glas für Systeme mit Nennspannungen über 1 kV
Essais des supports isolants d'intérieur et d'extérieur, en matière céramique ou en verre,
destinés à des installations de tension nominale supérieure à 1 kV
Ta slovenski standard je istoveten z: EN 60168:1994/A2:2000
ICS:
29.080.10 Izolatorji Insulators
SIST EN 60168:1997/A2:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60168:1997/A2:2002

---------------------- Page: 2 ----------------------

SIST EN 60168:1997/A2:2002
EUROPEAN STANDARD EN 60168/A2
NORME EUROPÉENNE
EUROPÄISCHE NORM December 2000

ICS 29.080.10


English version


Tests on indoor and outdoor post insulators of ceramic material or glass
for systems with nominal voltages greater than 1 kV
(IEC 60168:1994/A2:2000)


Essais des supports isolants d'intérieur Prüfungen an Innenraum- und
et d'extérieur, en matière céramique ou Freiluft-Stützisolatoren aus keramischem
en verre, destinés à des installations Werkstoff oder Glas für Systeme mit
de tension nominale supérieure à 1 kV Nennspannungen über 1 kV
(CEI 60168:1994/A2:2000) (IEC 60168:1994/A2:2000)






This amendment A2 modifies the European Standard EN 60168:1994; it was approved by CENELEC on
2000-11-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this amendment the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This amendment exists in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the
Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway,
Portugal, Spain, Sweden, Switzerland and United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2000 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.

  Ref. No. EN 60168:1994/A2:2000 E

---------------------- Page: 3 ----------------------

SIST EN 60168:1997/A2:2002
Page 2
EN 60168:1994/A2:2000
Foreword
The text of document 36C/121/FDIS, future amendment 2 to IEC 60168:1994, prepared by SC 36C,
Insulators for substatio
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN IEC 60305:2021(Main)
Insulators for overhead lines with a nominal voltage above 1000 V - Ceramic or glass insulator units for AC systems - Characteristics of insulator units of the cap and pin type (IEC 60305:2021)
EN IEC 60305:2021

This International Standard applies to string insulator units of the cap and pin type with
insulating parts of ceramic material or glass, intended for AC overhead lines with a nominal
voltage greater than 1 000 V and a frequency not greater than 100 Hz. It also applies to
insulators of similar design used in substations.
This document applies to string insulator units of the cap and pin type either with ball and
socket couplings or with clevis and tongue couplings.
This document applies to string insulator units for use on overhead lines in clean areas and
polluted areas. For use in areas characterized by very heavy pollution levels and for other
particular or extreme environmental conditions, it may be necessary for certain dimensions to
be changed and insulator units having different creepage distances, spacing and forms may
be preferred (for example, flat profile, hemispherical etc.). Insulators for use on DC systems
may also need different dimensions. In any case, it is applicable that the standardized
mechanical characteristics of this document and coupling sizes are retained.
The object of this document is to prescribe specified values for the mechanical characteristics
and for the main dimensions of string insulator units of the cap and pin type.
The power frequency, lightning impulse and puncture withstand voltages of string insulator
units are not specified in this document. IEC 60383-1 gives the electrical characteristics which
define string insulator units; their values are agreed between purchaser and manufacturer.
Ball and socket couplings are covered by IEC 60120, clevis and tongue couplings by
IEC 60471.
NOTE For the definition of site pollution severity see IEC TS 60815-1.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60433:2021(Main)
Insulators for overhead lines with a nominal voltage above 1000 V - Ceramic insulators for AC systems - Characteristics of insulator units of the long rod type (IEC 60433:2021)
EN IEC 60433:2021

This International Standard is applicable to string insulator units of the long rod type with
insulating parts of ceramic material intended for use in AC overhead power lines with a
nominal voltage greater than 1 000 V and a frequency not greater than 100 Hz. It is also
applicable to insulators of similar design, used in substations.
This document is applicable to ceramic string insulator units of the long rod type, either with a
clevis end fitting at both ends for coupling with a tongue, or with a socket end fitting at both
ends for coupling with a pin ball.
The object of this document is to prescribe specified values for electrical and mechanical
characteristics, and for the principal dimensions of ceramic string insulator units of the long
rod type.
This document is applicable to string insulator units for use on overhead lines situated in
lightly polluted areas, and the creepage distances given in Table 1 have been established
accordingly, using the IEC TS 60815-2 recommendation of 27,8 mm/kV for SPS class.
However, shorter creepage distances are applicable for use in some non-polluted areas. If
specific operating conditions require or allow non-standard (longer or shorter) creepage
distances, the mechanical characteristics as well as the lengths L (see Clause 4) of this
document are intended to be used unless the need for exceptionally long creepage distances
requires values of L greater than those given in Table 1. In the case of special requirements,
e.g. very heavy polluted areas and for other particular or extreme environmental conditions, it
may be necessary for certain dimensions to be changed.
As far as reasonably applicable, this document is also applicable to be applied to similar
insulator units outside the scope of this standard, such as insulators for electric traction lines.
This document does not include tests on insulators and dimensions of end fittings.
Ball and socket couplings are covered by IEC 60120, clevis and tongue couplings by
IEC 60471.
NOTE 1 For the definition of site pollution severity, see applicable part of IEC TS 60815.
NOTE 2 The term "ceramic" is used in this document to refer to porcelain materials and, contrary to North
American practice, does not include glass.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60471:2020(Main)
Clevis and tongue couplings of string insulator units - Dimensions (IEC 60471:2020)
EN IEC 60471:2020

This international standard applies to string insulator units of the cap and pin type and also of
the long rod type as well as the fittings used with such insulators.
The object of this document is to define the dimensions of a series of clevis and tongue
couplings to permit the assembly of insulators or fittings supplied by different manufacturers.
NOTE 1 IEC 60305 gives the coordination between the standardized dimensions of Table 1 and the strength
classes of cap and pin insulator. IEC 60433 gives the coordination between the standardized dimensions of Table 2
and the strength classes of long rod insulators.
NOTE 2 If the dimensions given in Table 1 are not sufficient, higher strength classes are given in IEC 60305.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60372:2020(Main)
Locking devices for ball and socket couplings of string insulator units - Dimensions and tests (IEC 60372:2020)
EN IEC 60372:2020

This international standard is applicable to locking devices used with ball and socket
couplings of string insulator units and used with the corresponding metal fittings standardized
in IEC 60120, when they are supplied separately.
When these locking devices are supplied with an insulator or fitting, they are considered as an
integral part of it. In this case, the relevant test is to be included with those of insulators, as
specified in IEC 60383-1 and IEC 61325. On request, a certificate is to be delivered
confirming that the tests on locking devices as specified in this document have been carried
out. The locking devices are usually supplied with the insulator or corresponding metal fittings.
The object of this document is
• to define the shapes and some standard dimensions for locking devices,
• to define the test methods for locking devices,
• to state the acceptance conditions for supply,
• to give other dimensions for guidance of manufacturing only.
The object of this document does not include the specification of the nature of the material,
and the material covered by the scope of this document does not have a surface coating for
corrosion protection. However, the material which will give rise to significant contact
corrosion(chemical reaction) between the locking device and the ball and socket coupling
does not covered by this document.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60120:2020(Main)
Ball and socket couplings of string insulator units - Dimensions (IEC 60120:2020)
EN IEC 60120:2020

The object of this international standard is to define the dimensions of a series of standard
ball and socket couplings using the standard locking devices (see IEC 60372) in order to
permit the assembly of insulators or metal fittings supplied by different manufacturers.
This document applies to string insulator units of the cap and pin and long rod types and their
associated metal fittings.
For the pin ball and the socket, dimensions apply to the finished product after any surface
treatment.
Extreme positions of the pin ball in the socket are given in Annex A.
Typical examples of gauges for checking the dimensions of pin balls and sockets are given in
Annex B.
NOTE Only the dimensions necessary for assembly are dealt with in this standard. Properties of material and
working loads are not specified. The co-ordination of dimensions with strength classes is specified in IEC 60305
and IEC 60433.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61952-1:2019(Main)
Insulators for overhead lines - Composite line post insulators for AC systems with a nominal voltage greater than 1 000 V - Part 1: definitions, end fittings and designations (IEC 61952-1:2019)
EN IEC 61952-1:2019

This document is applicable to composite line post insulators for AC overhead lines with a nominal voltage greater than 1 000 V and a frequency not greater than 100 Hz. It also applies to line post insulators of similar design used in substations or on electric traction lines. This document applies to line post insulators of composite type, generally with metallic couplings, with and without a base plate. It also applies to such insulators when used in complex structures. It does not apply to hollow insulators adapted for use as line post insulators. The object of this document is to specify the main dimensions of the couplings to be used on the composite line post insulators in order to permit the assembly of insulators or fittings supplied by different manufacturers and to allow, whenever practical, interchangeability with existing installations. It also specifies a standard designation system for composite line post insulators.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60507:2014/AC:2018(Corrigendum)
Artificial pollution tests on high-voltage ceramic and glass insulators to be used on a.c. systems (IEC 60507:2013/COR1:2018)
EN 60507:2014/AC:2018-09

IEC - Corrected version

  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61466-2:2000/A2:2018(Amendment)
Composite string insulator units for overhead lines with a nominal voltage greater than 1 000 V - Part 2: Dimensional and electrical characteristics (IEC 61466-2:1998/A2:2018)
EN 61466-2:1998/A2:2018
  • Addendum – translation
    8 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 62772:2017(Main)
Composite Hollow Core Station Post Insulators for substations with a.c. voltage greater than 1000 V and d.c. voltage greater than 1500V- Definitions, test methods and acceptance criteria (IEC 62772:2016)
EN 62772:2016

This International Standard applies to composite hollow core station post insulators consisting
of a load-bearing insulating tube (core) made of resin impregnated fibres an insulating filler
material (e.g. solid, liquid, foam, gaseous – pressurized or unpressurized), a housing (outside
the insulating tube) made of polymeric material (for example silicone or ethylene-propylene)
and metal fixing devices at the ends of the insulating tube. Composite hollow core station post
insulators as defined in this standard are intended for general use in substations in both,
outdoor and indoor environments, operating with a rated AC voltage greater than 1 000 V and
a frequency not greater than 100 Hz or for use in direct current systems with a rated voltage
greater than 1 500 V.
The object of this standard is:
– to define the terms used;
– to prescribe test methods;
– to prescribe acceptance criteria.
All the tests in this standard, apart from the thermal-mechanical test, are performed at normal
ambient temperature. This standard does not prescribe tests that may be characteristic of the
apparatus of which the composite hollow core station post insulator ultimately may form a
part. Further technical input is required in this area.
NOTE 1 "Pressurized" means a permanent gas or liquid pressure greater than 0,05 MPa (0,5 bar) gauge. The gas
can be dry air or inert gases, for example sulphur hexafluoride, nitrogen, or a mixture of such gases.
NOTE 2 "Unpressurized" means a gas or liquid pressure smaller than or equal to 0,05 MPa (0,5 bar) gauge.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61466-1:2016(Main)
Composite string insulator units for overhead lines with a nominal voltage greater than 1000 V - Part 1: Standard strength classes and end fittings (IEC 61466-1:2016)
EN 61466-1:2016

Prescribes specified values for the mechanical characteristics of the composite string insulator units. Defines the main dimensions of the couplings to be used on the composite string insulator units in order to permit the assembly of insulators of fittings supplied by different manufacturers and to allow, whenever practical, interchangeability with existing installations. It also defines a standard designation system for composite string insulator units.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    27 pages
    French language
    sale 10% off
    e-Library read for
    1 day
  • Standard – translation
    25 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day