SIST EN 13034:2005
(Main)Protective clothing against liquid chemicals - Performance requirements for chemical protective clothing offering limited protective performance against liquid chemicals (Type 6 and Type PB [6] equipment)
Protective clothing against liquid chemicals - Performance requirements for chemical protective clothing offering limited protective performance against liquid chemicals (Type 6 and Type PB [6] equipment)
This document specifies the minimum requirements for limited use and re-useable limited performance chemical protective clothing. Limited performance chemical protective clothing is intended for use in cases of a potential exposure to a light spray, liquid aerosols or low pressure, low volume splashes, against which a complete liquid permeation barrier (at the molecular level) is not required.
This document covers both chemical protective suits (Type 6) and partial body protection (Type PB [6]).
Chemical protective suits (Type 6) cover and protect at least the trunk and the limbs, e.g. one-piece coveralls or two piece suits, with or without hood, boot-socks or boot-covers. This document specifies minimum requirements for the connections between different parts of Type 6 suits by the use of a reduced whole suit spray test using a variant of EN 468:1994, as described in 5.2.
Partial body protection of similar limited performance (Type PB [6]) covers and protects only specific parts of the body, e.g. coats, aprons, sleeves etc. They should not be tested to the whole suit test (5.2).
Schutzkleidung gegen flüssige Chemikalien - Leistungsanforderungen an Chemikalienschutzkleidung mit eingeschränkter Schutzleistung gegen flüssige Chemikalien (Ausrüstung Typ 6 und Typ PB [6])
Dieses Dokument legt die Mindestanforderungen an Chemikalienschutzkleidung mit eingeschränkter
Schutzwirkung einschließlich wiederverwendbarer Schutzkleidung fest. Chemikalienschutzkleidung mit
eingeschränkter Schutzwirkung ist für die Verwendung in Fällen einer möglichen Exposition gegenüber
leichter Chemikalienversprühung, flüssigen Aerosolen oder mit niedrigem Druck auftreffenden Spritzern
geeignet, gegen die eine vollständige Barriere gegen Flüssigkeitspermeation (auf molekularer Ebene) nicht
erforderlich ist.
Dieses Dokument gilt für beide, die Chemikalienschutzbekleidungen (Typ 6) und den Teilkörperschutz (Typ
PB [6]).
Chemikalienschutzanzüge (Typ 6) bedecken und schützen mindestens den Rumpf und die Lenden, z. B.
einteilige Overalls und zweiteilige Anzüge mit oder ohne Haube, mit oder ohne Füßlinge oder Überschuhe.
Dieses Dokument legt auch die Mindestanforderungen für die Verbindungen zwischen den verschiedenen
Teilen von Typ-6-Anzügen durch Anwendung eines abgeschwächten Spray-Tests für den ganzen Anzug
mittels einer Variante von EN 468 fest, wie in 5.2 beschrieben.
Teilweiser Körperschutz mit ähnlicher eingeschränkter Schutzwirkung (Typ PB [6]) bedeckt und schützt nur
einen Teil des Körpers, wie z. B. Kittel oder Schürzen, Ärmel usw. Sie sollten jedoch nicht mit dem Test für
den ganzen Anzug (5.2) geprüft werden.
Vetements de protection contre les produits chimiques liquides - Exigences relatives aux vetements de protection chimique offrant une protection limitée contre les produits chimiques liquides (équipement de type 6 et Type PB (6))
La présente Norme européenne spécifie les exigences minimales relatives aux vetements de protection chimique a usage limité ou réutilisables offrant une protection limitée. Les vetements de protection chimique a usage limité sont conçus pour etre utilisés en cas d'exposition probable a de légeres pulvérisations, aux aérosols liquides ou a basse pression, de légeres éclaboussures, contre lesquels une barriere totale contre la perméation des liquides (au niveau moléculaire) n'est pas nécessaire.
La présente norme européenne couvre a la fois les combinaisons de protection chimique (Type 6) et les articles ne couvrant qu'une partie du corps (Type PB [6]).
Les combinaisons de protection (Type 6) couvrent et protegent au moins le tronc et les membres, comme par exemple les combinaisons une piece ou deux-pieces, avec ou sans capuche, bottes ou sur-bottes. La présente Norme européenne spécifie les exigences minimales pour les jonctions entre les différentes parties des combinaisons de Type 6 par la réalisation d'un essai au brouillard réduit sur la combinaison complete utilisant une variante de l'EN 468, comme décrit en 5.2.
Les vetements de protection couvrant partiellement le corps et offrant une performance limitée semblable (Type PB [6]), couvrent et protegent des parties spécifiques du corps, comme par exemple vestes, tabliers, manches, etc. Ils ne doivent pas etre soumis a l'essai de la combinaison complete (5.2).
Varovalna obleka pred učinki tekočih kemikalij - Zahteve za izdelavo oblačil za zaščito pred kemikalijami, ki nudijo omejeno zaščito pred tekočimi kemikalijami (oprema tipa 6 in tipa PB [6])
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Protective clothing against liquid chemicals - Performance requirements for chemical protective clothing offering limited protective performance against liquid chemicals (Type 6 and Type PB [6] equipment)Vetements de protection contre les produits chimiques liquides - Exigences relatives aux vetements de protection chimique offrant une protection limitée contre les produits chimiques liquides (équipement de type 6 et Type PB (6))Schutzkleidung gegen flüssige Chemikalien - Leistungsanforderungen an Chemikalienschutzkleidung mit eingeschränkter Schutzleistung gegen flüssige Chemikalien (Ausrüstung Typ 6 und Typ PB [6])13.340.10Varovalna oblekaProtective clothingICS:SIST EN 13034:2005enTa slovenski standard je istoveten z:EN 13034:200501-julij-2005SIST EN 13034:2005SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13034March 2005ICS 13.340.10English versionProtective clothing against liquid chemicals - Performancerequirements for chemical protective clothing offering limitedprotective performance against liquid chemicals (Type 6 andType PB [6] equipment)Vêtements de protection contre les produits chimiquesliquides - Exigences relatives aux vêtements de protectionchimique offrant une protection limitée contre les produitschimiques liquides (équipement de type 6 et Type PB (6))Schutzkleidung gegen flüssige Chemikalien -Leistungsanforderungen an Chemikalienschutzkleidung miteingeschränkter Schutzleistung gegen flüssige Chemikalien(Ausrüstung Typ 6 und Typ PB [6])This European Standard was approved by CEN on 14 February 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2005 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13034:2005: E
EN 13034:2005 (E) 2 Contents Page Foreword.3 Introduction.4 1 Scope.5 2 Normative references.5 3 Terms and definitions.5 4 Performance requirements for materials, seams joins and assemblages.6 4.1 Materials.6 4.2 Seams, joins and assemblages.7 5 Performance requirements for a whole suit.8 5.1 General.8 5.2 Resistance to penetration by liquids in the form of a light spray (mist test).8 6 Marking.9 7 Information supplied by the manufacturer.10 Annex ZA (informative)
Relationship between this European Standard and the Essential Requirements of EU Directive 89/686/EEC Personal Protective Equipment.12 Bibliography.13
EN 13034:2005 (E) 3 Foreword This document (EN 13034:2005) has been prepared by Technical Committee CEN/TC 162 “Protective clothing including hand and arm protection and lifejackets”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2005, and conflicting national standards shall be withdrawn at the latest by September 2005. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive 89/686/EEC. For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EN 13034:2005 (E) 4 Introduction Protection should be proportional to the risk to avoid excessive discomfort due to overprotection. The categorisation into types of chemical protective clothing is an attempt to discriminate between different general levels of risk. The determination of the actual risk level should follow from a risk assessment, which takes all relevant parameters into account, e.g. the nature of the chemical, temperature, pressure, quantity, parts of the body likely to be exposed, climatic conditions, intensity of work etc. This risk assessment will give important indications about suitable types of materials, clothing design and composition of the most effective solution, e.g. combination with other types of PPE or other items of chemical protective clothing. Type 6 and PB [6] are intended to be used in cases where risk has been assessed as low and a full liquid permeation barrier is not necessary, i.e. when wearers are able to take timely adequate action when their clothing is contaminated. Type 6 and PB [6] protective clothing form the lowest level of chemical protection and are intended to protect from a potential exposure to small quantities of spray or accidental low volume splashes. A technical report to give guidance on questions pertaining to selection, use, care and maintenance is currently under development.
EN 13034:2005 (E) 5 1 Scope This document specifies the minimum requirements for limited use and re-useable limited performance chemical protective clothing. Limited performance chemical protective clothing is intended for use in cases of a potential exposure to a light spray, liquid aerosols or low pressure, low volume splashes, against which a complete liquid permeation barrier (at the molecular level) is not required. This document covers both chemical protective suits (Type 6) and partial body protection (Type PB [6]). Chemical protective suits (Type 6) cover and protect at least the trunk and the limbs, e.g. one-piece coveralls or two piece suits, with or without hood, boot-socks or boot-covers. This document specifies minimum requirements for the connections between different parts of Type 6 suits by the use of a reduced whole suit spray test using a variant of EN 468, as described in 5.2. Partial body protection of similar limited performance (Type PB [6]) covers and protects only specific parts of the body, e.g. coats, aprons, sleeves etc. They should not be tested to the whole suit test (5.2). 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 340:2003, Protective clothing — General requirements EN 468, Protective clothing — Protection against liquid chemicals — Test method: Determination of resistance to penetration by spray (Spray Test) EN 14325:2004, Protective clothing against chemicals — Test methods and performance classification of chemical protective clothing materials, seams, joins and assemblages EN 23758, Textiles - Care labelling code using symbols (ISO 3758:1991) EN ISO 13935-2, Textiles — Seam tensile properties of fabrics and made-up textile articles — Part 2: Determination of maximum force to seam rupture using the grab method (ISO 13935-2:1999) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 aerosol suspension of solid, liquid or solid and liquid particles in a gaseous medium having negligible falling velocity (generally considered to be less than 0,25 m/s) 3.2 chemical protective clothing material any material or combination of materials used in an item of protective clothing for the purpose of isolating parts of the body from direct contact with a chemical 3.3 join non-permanent fastening between two different garments, or between chemical protective clothing and accessories
EN 13034:2005 (E) 6 3.4 seam permanent fastening between two or more pieces of chemical protective clothing material 3.5 assemblage permanent fastening between two or more different garments, or between chemical protective clothing and accessories, obtained e.g. by sewing, welding, vulcanising or gluing 3.6 closure device, e.g. a zipper, a touch-and-close fastener etc., to close openings for the donning of protective clothing 3.7 chemical protective suit (or whole suit) clothing worn to protect against chemicals, that covers at least trunk, arms and legs and where various types of additional protection e.g. hood or helmet, boots and gloves may be joined with. Several garments may be combined to provide the desired level of protection 3.8 partial body protection protective clothing item worn to protect one or more parts of the body, which are particularly exposed to the risk. Partial body protection may be used separately or in combination with other garments to increase the protection level of specific parts of the body. Examples of partial body protection are sleeves, aprons and laboratory coats 3.9 limited use protective clothing clothing intended for limited wear life usage (single use or limited re-use according to the manufacturer's instructions), i.e. to be worn until hygienic cleaning becomes necessary or until disposal is required after chemical contamination 3.10 re-usable chemical protective clothing clothing intended to be re-used after the necessary reprocessing steps, such as e.g. hygienic cleaning, decontamination, or reapplication of repellent treatments, whilst still providing adequate protection 3.11 penetration process by which chemicals and/or micro-organisms move through porous materials, seams, pinholes and other imperfections of a material on a non-molecular level 4 Performance requirements for materials, seams joins and assemblages 4.1 Materials Chemical protective clothing materials shall be tested and classified in accordance with Table 1 (see also EN 14325:2004, Clause 4). If not otherwise specified in the test methods, at least five specimens shall be tested for each property. The lowest individual value shall be calculated and used to describe the performance level. Pre-conditioning and conditioning shall be carried out in accordance with EN 14325:2004, 4.2 and 4.3, as required. Manufacturer's instructions with regard to number of cleaning cycles, cleaning procedures and possible reapplication of treatments shall be observed.
EN 13034:2005 (E) 7 For all requirements, except for liquid penetration and repellency, at least performance level 1 shall be obtained. For liquid repellency a performance level 3 shall be obtained for at least one of the chemicals referred to in EN 14325:2004, Clause 4. For resistance to penetration by liquids a performance level of at least 2 shall be obtained for at least one of the chemicals referred to in EN 14325:2004, Clause 4. Table 1 — Test requirements Clause in
EN 14325:2004 Performance requirement 4.4 Abrasion resistance 4.7 Tear resistance (trapezoidal test specimen) 4.9 Tensile strength 4.10 Puncture resistance 4.12 Liquid repellency 4.13 Resistance to penetration by liquids 4.14 Resistance to ignition
If a material does not provide a clearly measurable test result for any of the requirements in Table 1, "not applicable" shall be marked in both the test report and in the manufacturer's information. The reason why the test could not be applied or completed, shall be indicated, e.g. that the elasticity of the specimen prevents to determine an end-point in the puncture resistance test. Materials shall be known not to cause skin irritation or have any adverse effect to healt
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.