SIST ISO 13012-1:2009
Rolling bearings - Accessories for sleeve type linear ball bearings - Part 1: Boundary dimensions and tolerances for series 1 and 3
Rolling bearings - Accessories for sleeve type linear ball bearings - Part 1: Boundary dimensions and tolerances for series 1 and 3
This part of ISO 13012 specifies the boundary dimensions, other relevant dimensions and their tolerances of accessories for sleeve type linear ball bearings which are specified in ISO 10285.
This part of ISO 13012 applies to: housings — closed and adjustable flangeless housings for series 1 sleeve type linear ball bearings, closed and adjustable flanged housings for series 3 sleeve type linear ball bearings, open flanged housings for series 3 sleeve type linear ball bearings, closed and adjustable flangeless housings for series 3 sleeve type linear ball bearings, open and open adjustable flangeless housings for series 3 sleeve type linear ball bearings; shaft support rails — standard height shaft support rails for series 3 sleeve type linear ball bearings, low height shaft support rails for series 3 sleeve type linear ball bearings; shaft support blocks — flanged shaft support blocks for series 1 and 3 sleeve type linear ball bearings, flangeless shaft support blocks for series 1 and 3 sleeve type linear ball bearings; shafts — solid and tubular shafts for series 1 and 3 sleeve type linear ball bearings.
Wälzlager - Zubehör für Linearlager mit Kugelumlauf und Hülse - Teil 1: Grenzabmaße und Toleranzen für die Serien 1 und 3
Roulements - Accessoires pour douilles à billes linéaires - Partie 1: Dimensions d'encombrement et tolérances pour les séries 1 et 3
L'ISO 13012-1:2009 sp�cifie les dimensions d'encombrement et autres dimensions appropri�es, ainsi que leurs tol�rances, des accessoires pour les douilles � billes lin�aires sp�cifi�es dans l'ISO 10285.
L'ISO 13012-1:2009 s'applique aux accessoires suivants:
corps de palier —
� semelle, compacts, ferm�s et r�glables, pour les douilles � billes lin�aires de la s�rie 1,
� semelle, avec pattes de fixation, ferm�s et r�glables, pour les douilles � billes lin�aires de la s�rie 3,
� semelle, avec pattes de fixation, ouverts, pour les douilles � billes lin�aires de la s�rie 3,
� semelle, compacts, ferm�s et r�glables, pour les douilles � billes lin�aires de la s�rie 3,
� semelle, compacts, ouverts et ouverts et r�glables, pour les douilles � billes lin�aires de la s�rie 3;
rails supports d'arbre —
normalis�s, pour les douilles � billes lin�aires de la s�rie 3,
bas, pour les douilles � billes lin�aires de la s�rie 3;
paliers supports d'arbre —
� semelle, avec pattes de fixation, pour les douilles � billes lin�aires des s�ries 1 et 3,
� semelle, compacts, pour les douilles � billes lin�aires des s�ries 1 et 3;
arbres —
massifs et tubulaires, pour les douilles � billes lin�aires des s�ries 1 et 3.
Kotalni ležaji - Dodatki za linearne kroglične ležaje s kroženjem kroglic - 1. del: Zunanje mere in tolerance za seriji 1 in 3
General Information
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
SIST ISO 13012-1:2009
01-maj-2009
.RWDOQLOHåDML'RGDWNL]DOLQHDUQHNURJOLþQHOHåDMHVNURåHQMHPNURJOLFGHO
=XQDQMHPHUHLQWROHUDQFH]DVHULMLLQ
Rolling bearings - Accessories for sleeve type linear ball bearings - Part 1: Boundary
dimensions and tolerances for series 1 and 3
Wälzlager - Zubehör für Linearlager mit Kugelumlauf und Hülse - Teil 1: Grenzabmaße
und Toleranzen für die Serien 1 und 3
Roulements - Accessoires pour douilles à billes linéaires - Partie 1: Dimensions
d'encombrement et tolérances pour les séries 1 et 3
Ta slovenski standard je istoveten z: ISO 13012-1:2009
ICS:
21.100.20 Kotalni ležaji Rolling bearings
SIST ISO 13012-1:2009 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ISO 13012-1:2009
---------------------- Page: 2 ----------------------
SIST ISO 13012-1:2009
INTERNATIONAL ISO
STANDARD 13012-1
First edition
2009-02-01
Rolling bearings — Accessories for
sleeve type linear ball bearings —
Part 1:
Boundary dimensions and tolerances for
series 1 and 3
Roulements — Accessoires pour douilles à billes linéaires —
Partie 1: Dimensions d'encombrement et tolérances pour les séries 1
et 3
Reference number
ISO 13012-1:2009(E)
©
ISO 2009
---------------------- Page: 3 ----------------------
SIST ISO 13012-1:2009
ISO 13012-1:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2009 – All rights reserved
---------------------- Page: 4 ----------------------
SIST ISO 13012-1:2009
ISO 13012-1:2009(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope .1
2 Normative references .1
3 Terms and definitions .2
4 Symbols .3
4.1 Closed and adjustable flangeless housings for series 1 sleeve type linear ball bearings.3
4.2 Closed and adjustable flanged housings for series 3 sleeve type linear ball bearings.3
4.3 Open flanged housings for series 3 sleeve type linear ball bearings.4
4.4 Closed and adjustable flangeless housings for series 3 sleeve type linear ball bearings.4
4.5 Open and open adjustable flangeless housings for series 3 sleeve type linear ball
bearings .4
4.6 Standard height shaft support rails for series 3 sleeve type linear ball bearings .5
4.7 Low height shaft support rails for series 3 sleeve type linear ball bearings .5
4.8 Flanged shaft support blocks fo
...
INTERNATIONAL ISO
STANDARD 13012-1
First edition
2009-02-01
Rolling bearings — Accessories for
sleeve type linear ball bearings —
Part 1:
Boundary dimensions and tolerances for
series 1 and 3
Roulements — Accessoires pour douilles à billes linéaires —
Partie 1: Dimensions d'encombrement et tolérances pour les séries 1
et 3
Reference number
ISO 13012-1:2009(E)
©
ISO 2009
---------------------- Page: 1 ----------------------
ISO 13012-1:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2009 – All rights reserved
---------------------- Page: 2 ----------------------
ISO 13012-1:2009(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope .1
2 Normative references .1
3 Terms and definitions .2
4 Symbols .3
4.1 Closed and adjustable flangeless housings for series 1 sleeve type linear ball bearings.3
4.2 Closed and adjustable flanged housings for series 3 sleeve type linear ball bearings.3
4.3 Open flanged housings for series 3 sleeve type linear ball bearings.4
4.4 Closed and adjustable flangeless housings for series 3 sleeve type linear ball bearings.4
4.5 Open and open adjustable flangeless housings for series 3 sleeve type linear ball
bearings .4
4.6 Standard height shaft support rails for series 3 sleeve type linear ball bearings .5
4.7 Low height shaft support rails for series 3 sleeve type linear ball bearings .5
4.8 Flanged shaft support blocks for series 1 and 3 sleeve type linear ball bearings .6
4.9 Flangeless shaft support blocks for series 1 and 3 sleeve type linear ball bearings .6
4.10 Solid and tubular shafts for series 1 and 3 sleeve type linear ball bearings .6
5 Housings.7
5.1 General.7
5.2 Housings for series 1 sleeve type linear ball bearings.7
5.3 Housings for series 3 sleeve type linear ball bearings.7
6 Shaft support rails .
...
NORME ISO
INTERNATIONALE 13012-1
Première édition
2009-02-01
Roulements — Accessoires pour douilles
à billes linéaires —
Partie 1:
Dimensions d'encombrement et
tolérances pour les séries 1 et 3
Rolling bearings — Accessories for sleeve type linear ball bearings —
Part 1: Boundary dimensions and tolerances for series 1 and 3
Numéro de référence
ISO 13012-1:2009(F)
©
ISO 2009
---------------------- Page: 1 ----------------------
ISO 13012-1:2009(F)
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier
peut être imprimé ou visualisé, mais ne doit pas être modifié à moins que l'ordinateur employé à cet effet ne bénéficie d'une licence
autorisant l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées
acceptent de fait la responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute
responsabilité en la matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la création du présent fichier PDF sont disponibles dans la rubrique General Info
du fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir
l'exploitation de ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation,
veuillez en informer le Secrétariat central à l'adresse donnée ci-dessous.
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2009
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous
quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit
de l'ISO à l'adresse ci-après ou du comité membre de l'ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Publié en Suisse
ii © ISO 2009 – Tous droits réservés
---------------------- Page: 2 ----------------------
ISO 13012-1:2009(F)
Sommaire Page
Avant-propos. iv
Introduction . v
1 Domaine d'application.1
2 Références normatives .1
3 Termes et définitions.2
4 Symboles .3
4.1 Corps de palier à semelle, compacts, fermés et réglables pour les douilles à billes
linéaires de la série 1.3
4.2 Corps de palier à semelle, avec pattes de fixation, fermés et réglables pour les douilles à
billes linéaires de la série 3 .3
4.3 Corps de palier à semelle, avec pattes de fixation, ouverts pour les douilles à billes
linéaires de la série 3.4
4.4 Corps de palier à semelle, compacts, fermés et réglables pour les douilles à billes
linéaires de la série 3.4
4.5 Corps de palier à semelle, compacts, ouverts et ouverts et réglable pour les douilles à
billes linéaires de la série 3 .4
4.6 Rails supports d'arbre normalisés pour les douilles à billes linéaires de la série 3 .5
4.7 Rails supports d'arbre bas pour les douilles à billes linéaires de la série 3 .5
4.8 Paliers supports d'arbre à semelle, avec pattes de fixation, pour les douilles à billes
linéaires des séries 1 et 3 .6
4.9 Paliers suppor
...
SLOVENSKI STANDARD
oSIST ISO/DIS 13012-1:2008
01-julij-2008
.RWDOQLOHåDML'RGDWNL]DOLQHDUQHNURJOLþQHOHåDMHVNURåHQMHPNURJOLFGHO
=XQDQMHPHUHLQWROHUDQFH]DVHULMLLQ
Rolling bearings - Accessories for sleeve type linear ball bearings - Part 1: Boundary
dimensions and tolerances for series 1 and 3
Wälzlager - Zubehör für Linearlager mit Kugelumlauf und Hülse - Teil 1: Grenzabmaße
und Toleranzen für die Serien 1 und 3
Roulements - Accessoires pour douilles à billes linéaires - Partie 1: Dimensions
d'encombrement et tolérances pour les séries 1 et 3
Ta slovenski standard je istoveten z: ISO/FDIS 13012-1
ICS:
21.100.20 Kotalni ležaji Rolling bearings
oSIST ISO/DIS 13012-1:2008 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
DRAFT INTERNATIONAL STANDARD ISO/DIS 13012-1
ISO/TC 4/SC 11 Secretariat: ANSI
Voting begins on: Voting terminates on:
2007-01-23 2007-06-23
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Rolling bearings — Accessories for sleeve type recirculating
linear motion ball bearings —
Part 1:
Boundary dimensions and tolerances for series 1 and 3
Roulements — Accessoires pour roulements à mouvement linéaire à recirculation de billes, type manchon —
Partie 1: Dimensions d'encombrement et tolérances pour les séries 1 et 3
(Revision of ISO 13012:1998)
ICS 21.100.20
To expedite distribution, this document is circulated as received from the committee secretariat.
ISO Central Secretariat work of editing and text composition will be undertaken at publication
stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
© International Organization for Standardization, 2007
---------------------- Page: 2 ----------------------
ISO/DIS 13012-1
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall
not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the
unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user's country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying,
recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO's
member body in the country of the requester.
ISO copyright office
Case postale 56 CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
©
ii ISO 2007 – All rights reserved
---------------------- Page: 3 ----------------------
ISO/DIS 13012-1
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.