SIST EN ISO 2811-1:2011
(Main)Paints and varnishes - Determination of density - Part 1: Pyknometer method (ISO 2811-1:2011)
Paints and varnishes - Determination of density - Part 1: Pyknometer method (ISO 2811-1:2011)
This part of ISO 2811 specifies a method for determining the density of paints, varnishes and related products using a metal or Gay-Lussac pyknometer. The method is limited to materials of low or medium viscosity at the temperature of test. The Hubbard pyknometer (see ISO 3507) can be used for highly viscous materials.
Beschichtungsstoffe - Bestimmung der Dichte - Teil 1: Pyknometer-Verfahren (ISO 2811-1:2011)
Dieser Teil von ISO 2811 legt ein Verfahren zum Bestimmen der Dichte von Beschichtungsstoffen und
ähnlichen Produkten mit einem Pyknometer fest.
Das Verfahren ist nur für Stoffe mit niedriger oder mittlerer Viskosität bei der Prüftemperatur anwendbar. Das
Pyknometer nach Hubbard kann für hochviskose Stoffe verwendet werden.
Peintures et vernis - Détermination de la masse volumique - Partie 1: Méthode pycnométrique (ISO 2811-1:2011)
L'ISO 2811-1:2011 spécifie une méthode de détermination de la masse volumique des peintures, vernis et produits assimilés au moyen d'un pycnomètre en métal ou d'un pycnomètre de Gay-Lussac.
La méthode est limitée aux produits de viscosité faible ou moyenne à la température d'essai. Le pycnomètre de Hubbard (voir l'ISO 3507) peut être utilisé pour les produits à forte viscosité.
Barve in laki - Ugotavljanje gostote - 1. del: Metoda s piknometrom (ISO 2811-1:2011)
Ta del ISO 2811 določa metodo za ugotavljanje gostote barv, lakov in sorodnih proizvodov z uporabo kovinskega ali Gay-Lussacovega piknometra. Metoda je omejena na materiale, ki imajo pri temperaturi preskušanja nizko ali srednjo viskoznost. Za visokoviskozne materiale se lahko uporablja Hubbardov piknometer (glej ISO 3507).
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 2811-1:2011
01-november-2011
1DGRPHãþD
SIST EN ISO 2811-1:2002
SIST EN ISO 2811-1:2002/AC:2006
Barve in laki - Ugotavljanje gostote - 1. del: Metoda s piknometrom (ISO 2811-
1:2011)
Paints and varnishes - Determination of density - Part 1: Pyknometer method (ISO 2811-
1:2011)
Beschichtungsstoffe - Bestimmung der Dichte - Teil 1: Pyknometer-Verfahren (ISO 2811-
1:2011)
Peintures et vernis - Détermination de la masse volumique - Partie 1: Méthode
pycnométrique (ISO 2811-1:2011)
Ta slovenski standard je istoveten z: EN ISO 2811-1:2011
ICS:
87.040 Barve in laki Paints and varnishes
SIST EN ISO 2811-1:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 2811-1:2011
---------------------- Page: 2 ----------------------
SIST EN ISO 2811-1:2011
EUROPEAN STANDARD
EN ISO 2811-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2011
ICS 87.040 Supersedes EN ISO 2811-1:2001
English Version
Paints and varnishes - Determination of density - Part 1:
Pyknometer method (ISO 2811-1:2011)
Peintures et vernis - Détermination de la masse volumique Beschichtungsstoffe - Bestimmung der Dichte - Teil 1:
- Partie 1: Méthode pycnométrique (ISO 2811-1:2011) Pyknometer-Verfahren (ISO 2811-1:2011)
This European Standard was approved by CEN on 19 February 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 2811-1:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 2811-1:2011
EN ISO 2811-1:2011 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 2811-1:2011
EN ISO 2811-1:2011 (E)
Foreword
This document (EN ISO 2811-1:2011) has been prepared by Technical Committee ISO/TC 35 "Paints and
varnishes" in collaboration with Technical Committee CEN/TC 139 “Paints and varnishes” the secretariat of
which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by September 2011, and conflicting national standards shall be
withdrawn at the latest by September 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 2811-1:2001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 2811-1:2011 has been approved by CEN as a EN ISO 2811-1:2011 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 2811-1:2011
---------------------- Page: 6 ----------------------
SIST EN ISO 2811-1:2011
INTERNATIONAL ISO
STANDARD 2811-1
Second edition
2011-03-01
Paints and varnishes — Determination of
density —
Part 1:
Pyknometer method
Peintures et vernis — Détermination de la masse volumique —
Partie 1: Méthode pycnométrique
Reference number
ISO 2811-1:2011(E)
©
ISO 2011
---------------------- Page: 7 ----------------------
SIST EN ISO 2811-1:2011
ISO 2811-1:2011(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 2811-1:2011
ISO 2811-1:2011(E)
Contents Page
Foreword .iv
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
4 Principle .1
5 Temperature.2
6 Apparatus.2
7 Sampling .2
8 Procedure.2
8.1 General .2
8.2 Determination .3
9 Calculation .4
10 Precision .4
10.1 Repeatability limit, r .4
10.2 Reproducibility limit, R.4
11 Test report.5
Annex A (informative) Example of a calibration method .6
Annex B (informative) Temperature variation.8
Bibliography.10
© ISO 2011 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 2811-1:2011
ISO 2811-1:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 2811-1 was prepared by Technical Committee ISO/TC 35, Paints and varnishes, Subcommittee SC 9,
General test methods for paints and varnishes.
This second edition cancels and replaces the first edition (ISO 2811-1:1997), which has been technically
revised.
The main changes are the following.
a) The unit for the density has been changed from grams per millilitre to grams per cubic centimetre,
because this is the more common SI unit.
b) The determination in duplicate has been changed to a single determination.
c) The information on calibration procedure has been changed to an example only and the status of
Annex B has been changed from normative to informative.
d) The Hubbard pyknometer has been deleted because it is not used for paints and varnishes and their raw
materials, but for bitumen and putty only (see ISO 3507).
e) The dust-proof container has been deleted because it is not used in practice.
f) The precision data has been updated by an interlaboratory test.
g) The normative references have been updated.
ISO 2811 consists of the following parts, under the general title Paints and varnishes — Determination of
density:
⎯ Part 1: Pyknometer method
⎯ Part 2: Immersed body (plummet) method
⎯ Part 3: Oscillation method
⎯ Part 4: Pressure cup method
iv © ISO 2011 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 2811-1:2011
INTERNATIONAL STANDARD ISO 2811-1:2011(E)
Paints and varnishes — Determination of density —
Part 1:
Pyknometer method
1 Scope
This part of ISO 2811 specifies a method for determining the density of paints, varnishes and related products
using a metal or Gay-Lussac pyknometer.
The method is limited to materials of low or medium viscosity at the temperature of test. The Hubbard
pyknometer (see ISO 3507) can be used for highly viscous materials.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 1513, Paints and varnishes — Examination and preparation of test samples
ISO 3696, Water for analytical
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.