Short Range Devices - Transport and Traffic Telematics (TTT) - Short Range Radar equipment operating in the 77 GHz to 81 GHz band - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU

The present document specifies the technical requirements and methods of measurement for Short Range Devices (SRD)
working as broadband devices with at least 50 MHz occupied bandwidth in the 77 GHz to 81 GHz frequency range,
intended for Transport and Traffic Telematics (TTT) applications. Applications include but are not limited to e.g. Short
Range Radar (SRR) for obstacle detection, stop&go, blind spot detection, parking aid, backup aid and precrash.
The present document covers transmitters intended to operate in the frequency range as defined in the EC Decision
2004/545/EC [i.5] and the ECC Decision ECC/DEC/(04)03 [i.6].
The present document:
a) contains the technical characteristics and test methods for short range radar equipment fitted with integral
antennas operating in 77 GHz to 81 GHz range;
b) covers short range radar vehicle applications in the 77 GHz to 81 GHz range. It covers integrated transceivers
and separate transmit/receive modules;
c) integrated multi-mode transceivers defined in ETSI EG 203 367 [i.9], transmitters and receivers in the 76 GHz
to 77 GHz range which comply with ETSI EN 301 091-1 [i.8] and which use the 77 GHz to 81 GHz range for
one or several operation modes, within one EUT cycle or in different vehicle operation modes.
For such sensors, the 77 GHz to 81 GHz operation modes should be available for testing separately from the
76 GHz to 77 GHz operation modes.
The present document does not necessarily include all the characteristics which may be required by a user, nor does it
necessarily represent the optimum performance achievable.
In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present
document and ETSI EN 303 396 [1], the provisions of the present document take precedence.

Naprave kratkega dosega - Transportna in prometna telematika (TTT) - Radarska oprema kratkega dosega, ki deluje v pasu od 77 GHz do 81 GHz - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU

Ta dokument določa tehnične lastnosti in merilne metode za naprave kratkega dosega (SRD), ki delujejo kot širokopasovne naprave z zasedeno pasovno širino vsaj 50 MHz v frekvenčnem območju od 77 GHz do 81 GHz, namenjene za transportno in prometno telematiko (TTT). Med možne načine uporabe med drugim spada na primer radar kratkega dosega (SRR) za zaznavanje ovir, zagotavljanje funkcije »ustavi in spelji«, zaznavanje mrtvih točk, pomoč pri parkiranju, podporo in opozarjanje na nesreče.
Ta dokument zajema oddajnike, ki so namenjeni delovanju v frekvenčnem območju, kot je določeno v odločbi ES 2004/545/ES [i.5] in odločbi ECC ECC/DEC/(04)03 [i.6].
Ta dokument:
a) vsebuje tehnične lastnosti in preskusne metode za radarsko opremo kratkega dosega, opremljeno z vgrajenimi antenami, ki deluje v območju od 77 GHz do 81 GHz;
b) zajema avtomobilske radarje kratkega dosega v območju od 77 GHz do 81 GHz. Zajema vgrajene oddajno-sprejemne naprave ter ločene oddajne/sprejemne module;
c) zajema večnačinovne oddajno-sprejemne naprave, opredeljene v standardu ETSI EG 203 367 [i.9], oddajnike in sprejemnike v območju od 76 GHz do 77 GHz, ki so skladni s standardom ETSI EN 301 091-1 [i.8] in uporabljajo območje od 77 GHz do 81 GHZ za enega ali več načinov delovanja, v enem ciklu preskušane opreme ali v različnih načinih delovanja vozila.
Pri takšnih senzorjih morajo biti načini delovanja v območju od 77 GHz do 81 GHz na voljo za preskušanje ločeno do načinov delovanja v območju od 76 GHz do 77 GHz.
Ta dokument ne vključuje nujno vseh lastnosti, ki bi jih lahko potreboval uporabnik, in ne predstavlja nujno najboljšega mogočega delovanja.
Če se ta dokument in standard ETSI EN 303 396 [1] razlikujeta (na primer glede posebnih pogojev, opredelitev, kratic), imajo prednost določbe tega dokumenta.

General Information

Status
Published
Public Enquiry End Date
30-Sep-2016
Publication Date
28-May-2017
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
15-May-2017
Due Date
20-Jul-2017
Completion Date
29-May-2017

Buy Standard

Standard
SIST EN 302 264 V2.1.1:2017
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day
Standard
ETSI EN 302 264 V2.1.1 (2017-05) - Short Range Devices; Transport and Traffic Telematics (TTT); Short Range Radar equipment operating in the 77 GHz to 81 GHz band; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
English language
17 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI EN 302 264 V2.1.1 (2017-02) - Short Range Radar equipment operating in the 77 GHz to 81 GHz band; Short Range Radar equipment operating in the 77 GHz to 81 GHz band; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
English language
17 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ETSI EN 302 264 V2.1.0 (2016-07) - Short Range Devices; Transport and Traffic Telematics (TTT); Short Range Radar equipment operating in the 77 GHz to 81 GHz band; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
English language
19 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.UPRQL]LUDQL(8Short Range Devices - Transport and Traffic Telematics (TTT) - Short Range Radar equipment operating in the 77 GHz to 81 GHz band - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU35.240.60Uporabniške rešitve IT v prometuIT applications in transport33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:ETSI EN 302 264 V2.1.1 (2017-05)SIST EN 302 264 V2.1.1:2017en01-julij-2017SIST EN 302 264 V2.1.1:2017SLOVENSKI

STANDARD
SIST EN 302 264 V2.1.1:2017

ETSI EN 302 264 V2.1.1 (2017-05) Short Range Devices; Transport and Traffic Telematics (TTT); Short Range Radar equipment operating in the 77 GHz to 81 GHz band; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU

HARMONISED EUROPEAN STANDARD SIST EN 302 264 V2.1.1:2017
ETSI ETSI EN 302 264 V2.1.1 (2017-05) 2

Reference REN/ERM-TGSRR-76 Keywords harmonised standard, radar, radio, RTTT, SRD, testing, UWB ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88

Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2017. All rights reserved.

DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 302 264 V2.1.1:2017

ETSI ETSI EN 302 264 V2.1.1 (2017-05) 3 Contents Intellectual Property Rights ................................................................................................................................ 5 Foreword ............................................................................................................................................................. 5 Modal verbs terminology .................................................................................................................................... 5 Introduction ........................................................................................................................................................ 5 1 Scope ........................................................................................................................................................ 6 2 References ................................................................................................................................................ 6 2.1 Normative references ......................................................................................................................................... 6 2.2 Informative references ........................................................................................................................................ 7 3 Definitions, symbols and abbreviations ................................................................................................... 7 3.1 Definitions .......................................................................................................................................................... 7 3.2 Symbols .............................................................................................................................................................. 8 3.3 Abbreviations ..................................................................................................................................................... 8 4 Technical requirements specifications ..................................................................................................... 8 4.1 Environmental conditions ................................................................................................................................... 8 4.2 General ............................................................................................................................................................... 8 4.2.1 Background information ............................................................................................................................... 8 4.2.2 Wanted performance criteria......................................................................................................................... 8 4.2.3 Fixed and scanning antennas ........................................................................................................................ 8 4.3 Transmitter Conformance Requirements ............................................................................................................ 9 4.3.1 Operating Frequency Range ......................................................................................................................... 9 4.3.1.1 Applicability............................................................................................................................................ 9 4.3.1.2 Description .............................................................................................................................................. 9 4.3.1.3 Limits ...................................................................................................................................................... 9 4.3.1.4 Conformance ........................................................................................................................................... 9 4.3.2 Mean Power spectral density ........................................................................................................................ 9 4.3.2.1 Applicability............................................................................................................................................ 9 4.3.2.2 Description .............................................................................................................................................. 9 4.3.2.3 Limits ...................................................................................................................................................... 9 4.3.2.4 Conformance ........................................................................................................................................... 9 4.3.3 Peak Power ................................................................................................................................................. 10 4.3.3.1 Applicability.......................................................................................................................................... 10 4.3.3.2 Description ............................................................................................................................................ 10 4.3.3.3 Limits .................................................................................................................................................... 10 4.3.3.4 Conformance ......................................................................................................................................... 10 4.3.4 Unwanted emissions in the out-of-band domain ......................................................................................... 10 4.3.4.1 Applicability.......................................................................................................................................... 10 4.3.4.2 Description ............................................................................................................................................ 10 4.3.4.3 Limits .................................................................................................................................................... 10 4.3.4.4 Conformance ......................................................................................................................................... 10 4.3.5 Unwanted emissions in the spurious domain .............................................................................................. 11 4.3.5.1 Applicability.......................................................................................................................................... 11 4.3.5.2 Description ............................................................................................................................................ 11 4.3.5.3 Limits .................................................................................................................................................... 11 4.3.5.4 Conformance ......................................................................................................................................... 11 4.4 Receiver Conformance Requirements .............................................................................................................. 11 4.4.1 Introduction................................................................................................................................................. 11 4.4.2 Receiver spurious emissions ....................................................................................................................... 12 4.4.2.1 Applicability.......................................................................................................................................... 12 4.4.2.2 Description ............................................................................................................................................ 12 4.4.2.3 Limits .................................................................................................................................................... 12 4.4.2.4 Conformance ......................................................................................................................................... 12 4.4.3 Receiver in-band, out-of-band and remote-band signals handling.............................................................. 12 4.4.3.1 Applicability.......................................................................................................................................... 12 4.4.3.2 Description ............................................................................................................................................ 12 SIST EN 302 264 V2.1.1:2017

ETSI ETSI EN 302 264 V2.1.1 (2017-05) 4 4.4.3.3 Limits .................................................................................................................................................... 13 4.4.3.4 Conformance ......................................................................................................................................... 13 4.4.4 Receiver sensitivity ..................................................................................................................................... 13 4.5 Other requirements and mitigation techniques ................................................................................................. 13 4.5.1 Installation requirements ............................................................................................................................. 13 4.5.1.1 Applicability.......................................................................................................................................... 13 4.5.1.2 Description ............................................................................................................................................ 13 4.5.1.3 Limits .................................................................................................................................................... 13 4.5.1.4 Conformance ......................................................................................................................................... 14 5 General considerations for performing the tests ..................................................................................... 14 6 Test setup and procedures ...................................................................................................................... 14 7 Conformance methods of measurement for transmitter and receiver ..................................................... 14 Annex A (informative): Relationship between the present document and the essential requirements of Directive 2014/53/EU ......................................................... 15 Annex B (informative): Change history ............................................................................................... 16 History .............................................................................................................................................................. 17

SIST EN 302 264 V2.1.1:2017

ETSI ETSI EN 302 264 V2.1.1 (2017-05) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https://ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.7] to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC [i.2]. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive and associated EFTA regulations. The present document covers short range radar equipment operating in the 77 GHz to 81 GHz range. The present document covers the essential requirements of article 3.2 of the Directive 2014/53/EU [i.2].

National transposition dates Date of adoption of this EN: 11 April 2017 Date of latest announcement of this EN (doa): 31 July 2017 Date of latest publication of new National Standard or endorsement of this EN (dop/e):

31 January 2018 Date of withdrawal of any conflicting National Standard (dow): 31 January 2019

Modal verbs terminology In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). "must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation. Introduction The present document, together with ETSI EN 303 396 [1], covers the assessment of certain types of equipment as defined herein.

SIST EN 302 264 V2.1.1:2017

ETSI ETSI EN 302 264 V2.1.1 (2017-05) 6 1 Scope The present document specifies the technical requirements and methods of measurement for Short Range Devices (SRD) working as broadband devices with at least 50 MHz occupied bandwidth in the 77 GHz to 81 GHz frequency range, intended for Transport and Traffic Telematics (TTT) applications. Applications include but are not limited to e.g. Short Range Radar (SRR) for obstacle detection, stop&go, blind spot detection, parking aid, backup aid and precrash.

The present document covers transmitters intended to operate in the frequency range as defined in the EC Decision 2004/545/EC [i.5] and the ECC Decision ECC/DEC/(04)03 [i.6]. The present document: a) contains the technical characteristics and test methods for short range radar equipment fitted with integral antennas operating in 77 GHz to 81 GHz range; b) covers short range radar vehicle applications in the 77 GHz to 81 GHz range. It covers integrated transceivers and separate transmit/receive modules; c) integrated multi-mode transceivers defined in ETSI EG 203 367 [i.9], transmitters and receivers in the 76 GHz to 77 GHz range which comply with ETSI EN 301 091-1 [i.8] and which use the 77 GHz to 81 GHz range for one or several operation modes, within one EUT cycle or in different vehicle operation modes. For such sensors, the 77 GHz to 81 GHz operation modes should be available for testing separately from the 76 GHz to 77 GHz operation modes. The present document does not necessarily include all the characteristics which may be required by a user, nor does it necessarily represent the optimum performance achievable. In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present document and ETSI EN 303 396 [1], the provisions of the present document take precedence. These radio equipment types are capable of operating in all or part of the frequency bands given in table 1. Table 1: Permitted ranges of operation Permitted ranges of operation Transmit 77 GHz to 81 GHz Receive 77 GHz to 81 GHz

The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU [i.2] under the conditions identified in annex A. 2 References 2.1 Normative references References are specific, identified by date of publication and/or edition number or version number. Only the cited version applies. Referenced documents which are not found to be publicl

...

ETSI EN 302 264 V2.1.1 (2017-05)
HARMONISED EUROPEAN STANDARD
Short Range Devices;
Transport and Traffic Telematics (TTT);
Short Range Radar equipment operating
in the 77 GHz to 81 GHz band;
Harmonised Standard covering the essential requirements
of article 3.2 of Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 ETSI EN 302 264 V2.1.1 (2017-05)
Reference
REN/ERM-TGSRR-76
Keywords
harmonised standard, radar, radio, RTTT, SRD,
testing, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the

print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2017.
All rights reserved.
TM TM TM

DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.

3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members

GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.

ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 302 264 V2.1.1 (2017-05)
Contents

Intellectual Property Rights ................................................................................................................................ 5

Foreword ............................................................................................................................................................. 5

Modal verbs terminology .................................................................................................................................... 5

Introduction ........................................................................................................................................................ 5

1 Scope ........................................................................................................................................................ 6

2 References ................................................................................................................................................ 6

2.1 Normative references ......................................................................................................................................... 6

2.2 Informative references ........................................................................................................................................ 7

3 Definitions, symbols and abbreviations ................................................................................................... 7

3.1 Definitions .......................................................................................................................................................... 7

3.2 Symbols .............................................................................................................................................................. 8

3.3 Abbreviations ..................................................................................................................................................... 8

4 Technical requirements specifications ..................................................................................................... 8

4.1 Environmental conditions ................................................................................................................................... 8

4.2 General ............................................................................................................................................................... 8

4.2.1 Background information ............................................................................................................................... 8

4.2.2 Wanted performance criteria......................................................................................................................... 8

4.2.3 Fixed and scanning antennas ........................................................................................................................ 8

4.3 Transmitter Conformance Requirements ............................................................................................................ 9

4.3.1 Operating Frequency Range ......................................................................................................................... 9

4.3.1.1 Applicability............................................................................................................................................ 9

4.3.1.2 Description .............................................................................................................................................. 9

4.3.1.3 Limits ...................................................................................................................................................... 9

4.3.1.4 Conformance ........................................................................................................................................... 9

4.3.2 Mean Power spectral density ........................................................................................................................ 9

4.3.2.1 Applicability............................................................................................................................................ 9

4.3.2.2 Description .............................................................................................................................................. 9

4.3.2.3 Limits ...................................................................................................................................................... 9

4.3.2.4 Conformance ........................................................................................................................................... 9

4.3.3 Peak Power ................................................................................................................................................. 10

4.3.3.1 Applicability.......................................................................................................................................... 10

4.3.3.2 Description ............................................................................................................................................ 10

4.3.3.3 Limits .................................................................................................................................................... 10

4.3.3.4 Conformance ......................................................................................................................................... 10

4.3.4 Unwanted emissions in the out-of-band domain ......................................................................................... 10

4.3.4.1 Applicability.......................................................................................................................................... 10

4.3.4.2 Description ............................................................................................................................................ 10

4.3.4.3 Limits .................................................................................................................................................... 10

4.3.4.4 Conformance ......................................................................................................................................... 10

4.3.5 Unwanted emissions in the spurious domain .............................................................................................. 11

4.3.5.1 Applicability.......................................................................................................................................... 11

4.3.5.2 Description ............................................................................................................................................ 11

4.3.5.3 Limits .................................................................................................................................................... 11

4.3.5.4 Conformance ......................................................................................................................................... 11

4.4 Receiver Conformance Requirements .............................................................................................................. 11

4.4.1 Introduction................................................................................................................................................. 11

4.4.2 Receiver spurious emissions ....................................................................................................................... 12

4.4.2.1 Applicability.......................................................................................................................................... 12

4.4.2.2 Description ............................................................................................................................................ 12

4.4.2.3 Limits .................................................................................................................................................... 12

4.4.2.4 Conformance ......................................................................................................................................... 12

4.4.3 Receiver in-band, out-of-band and remote-band signals handling.............................................................. 12

4.4.3.1 Applicability.......................................................................................................................................... 12

4.4.3.2 Description ............................................................................................................................................ 12

ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 302 264 V2.1.1 (2017-05)

4.4.3.3 Limits .................................................................................................................................................... 13

4.4.3.4 Conformance ......................................................................................................................................... 13

4.4.4 Receiver sensitivity ..................................................................................................................................... 13

4.5 Other requirements and mitigation techniques ................................................................................................. 13

4.5.1 Installation requirements ............................................................................................................................. 13

4.5.1.1 Applicability.......................................................................................................................................... 13

4.5.1.2 Description ............................................................................................................................................ 13

4.5.1.3 Limits .................................................................................................................................................... 13

4.5.1.4 Conformance ......................................................................................................................................... 14

5 General considerations for performing the tests ..................................................................................... 14

6 Test setup and procedures ...................................................................................................................... 14

7 Conformance methods of measurement for transmitter and receiver ..................................................... 14

Annex A (informative): Relationship between the present document and the essential

requirements of Directive 2014/53/EU ......................................................... 15

Annex B (informative): Change history ............................................................................................... 16

History .............................................................................................................................................................. 17

ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 302 264 V2.1.1 (2017-05)
Intellectual Property Rights

IPRs essential or potentially essential to the present document may have been declared to ETSI. The information

pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found

in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in

respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web

server (https://ipr.etsi.org/).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee

can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

server) which are, or may be, or may become, essential to the present document.
Foreword

This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic

compatibility and Radio spectrum Matters (ERM).

The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.7] to

provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation

of the laws of the Member States relating to the making available on the market of radio equipment and repealing

Directive 1999/5/EC [i.2].

Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with

the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present

document, a presumption of conformity with the corresponding essential requirements of that Directive and associated

EFTA regulations.

The present document covers short range radar equipment operating in the 77 GHz to 81 GHz range.

The present document covers the essential requirements of article 3.2 of the Directive 2014/53/EU [i.2].

National transposition dates
Date of adoption of this EN: 11 April 2017
Date of latest announcement of this EN (doa): 31 July 2017
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 January 2018
Date of withdrawal of any conflicting National Standard (dow): 31 January 2019
Modal verbs terminology

In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and

"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of

provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

Introduction

The present document, together with ETSI EN 303 396 [1], covers the assessment of certain types of equipment as

defined herein.
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 302 264 V2.1.1 (2017-05)
1 Scope

The present document specifies the technical requirements and methods of measurement for Short Range Devices (SRD)

working as broadband devices with at least 50 MHz occupied bandwidth in the 77 GHz to 81 GHz frequency range,

intended for Transport and Traffic Telematics (TTT) applications. Applications include but are not limited to e.g. Short

Range Radar (SRR) for obstacle detection, stop&go, blind spot detection, parking aid, backup aid and precrash.

The present document covers transmitters intended to operate in the frequency range as defined in the EC Decision

2004/545/EC [i.5] and the ECC Decision ECC/DEC/(04)03 [i.6].
The present document:

a) contains the technical characteristics and test methods for short range radar equipment fitted with integral

antennas operating in 77 GHz to 81 GHz range;

b) covers short range radar vehicle applications in the 77 GHz to 81 GHz range. It covers integrated transceivers

and separate transmit/receive modules;

c) integrated multi-mode transceivers defined in ETSI EG 203 367 [i.9], transmitters and receivers in the 76 GHz

to 77 GHz range which comply with ETSI EN 301 091-1 [i.8] and which use the 77 GHz to 81 GHz range for

one or several operation modes, within one EUT cycle or in different vehicle operation modes.

For such sensors, the 77 GHz to 81 GHz operation modes should be available for testing separately from the

76 GHz to 77 GHz operation modes.

The present document does not necessarily include all the characteristics which may be required by a user, nor does it

necessarily represent the optimum performance achievable.

In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present

document and ETSI EN 303 396 [1], the provisions of the present document take precedence.

These radio equipment types are capable of operating in all or part of the frequency bands given in table 1.

Table 1: Permitted ranges of operation
Permitted ranges of operation
Transmit 77 GHz to 81 GHz
Receive 77 GHz to 81 GHz

The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU [i.2] under the

conditions identified in annex A.
2 References
2.1 Normative references

References are specific, identified by date of publication and/or edition number or version number. Only the cited

version applies.

Referenced documents which are not found to be publicly available in the expected location might be found at

https://docbox.etsi.org/Reference/.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are necessary for the application of the present document.

[1] ETSI EN 303 396 (V1.1.1) (12-2016): "Short Range Devices; Measurement Techniques for

automotive and surveillance radar equipment".
ETSI
---------------------- Page: 6 ----------------------
7 ETS
...

Final draft ETSI EN 302 264 V2.1.1 (2017-02)
HARMONISED EUROPEAN STANDARD
Short Range Devices;
Transport and Traffic Telematics (TTT);
Short Range Radar equipment operating
in the 77 GHz to 81 GHz band;
Harmonised Standard covering the essential requirements
of article 3.2 of Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 302 264 V2.1.1 (2017-02)
Reference
REN/ERM-TGSRR-76
Keywords
harmonised standard, radar, radio, RTTT, SRD,
testing, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the

print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2017.
All rights reserved.
TM TM TM

DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.

3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.

GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.

ETSI
---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 302 264 V2.1.1 (2017-02)
Contents

Intellectual Property Rights ................................................................................................................................ 5

Foreword ............................................................................................................................................................. 5

Modal verbs terminology .................................................................................................................................... 5

Introduction ........................................................................................................................................................ 5

1 Scope ........................................................................................................................................................ 6

2 References ................................................................................................................................................ 6

2.1 Normative references ......................................................................................................................................... 6

2.2 Informative references ........................................................................................................................................ 7

3 Definitions, symbols and abbreviations ................................................................................................... 8

3.1 Definitions .......................................................................................................................................................... 8

3.2 Symbols .............................................................................................................................................................. 8

3.3 Abbreviations ..................................................................................................................................................... 8

4 Technical requirements specifications ..................................................................................................... 8

4.1 Environmental conditions ................................................................................................................................... 8

4.2 General ............................................................................................................................................................... 8

4.2.1 Background information ............................................................................................................................... 8

4.2.2 Wanted performance criteria......................................................................................................................... 9

4.2.3 Fixed and scanning antennas ........................................................................................................................ 9

4.3 Transmitter Conformance Requirements ............................................................................................................ 9

4.3.1 Operating Frequency Range ......................................................................................................................... 9

4.3.1.1 Applicability............................................................................................................................................ 9

4.3.1.2 Description .............................................................................................................................................. 9

4.3.1.3 Limits ...................................................................................................................................................... 9

4.3.1.4 Conformance ........................................................................................................................................... 9

4.3.2 Mean Power spectral density ........................................................................................................................ 9

4.3.2.1 Applicability............................................................................................................................................ 9

4.3.2.2 Description .............................................................................................................................................. 9

4.3.2.3 Limits .................................................................................................................................................... 10

4.3.2.4 Conformance ......................................................................................................................................... 10

4.3.3 Peak Power ................................................................................................................................................. 10

4.3.3.1 Applicability.......................................................................................................................................... 10

4.3.3.2 Description ............................................................................................................................................ 10

4.3.3.3 Limits .................................................................................................................................................... 10

4.3.3.4 Conformance ......................................................................................................................................... 10

4.3.4 Unwanted emissions in the out-of-band domain ......................................................................................... 10

4.3.4.1 Applicability.......................................................................................................................................... 10

4.3.4.2 Description ............................................................................................................................................ 10

4.3.4.3 Limits .................................................................................................................................................... 10

4.3.4.4 Conformance ......................................................................................................................................... 11

4.3.5 Unwanted emissions in the spurious domain .............................................................................................. 11

4.3.5.1 Applicability.......................................................................................................................................... 11

4.3.5.2 Description ............................................................................................................................................ 11

4.3.5.3 Limits .................................................................................................................................................... 11

4.3.5.4 Conformance ......................................................................................................................................... 11

4.4 Receiver Conformance Requirements .............................................................................................................. 12

4.4.1 Introduction................................................................................................................................................. 12

4.4.2 Receiver spurious emissions ....................................................................................................................... 12

4.4.2.1 Applicability.......................................................................................................................................... 12

4.4.2.2 Description ............................................................................................................................................ 12

4.4.2.3 Limits .................................................................................................................................................... 12

4.4.2.4 Conformance ......................................................................................................................................... 12

4.4.3 Receiver in-band, out-of-band and remote-band signals handling.............................................................. 13

4.4.3.1 Applicability.......................................................................................................................................... 13

4.4.3.2 Description ............................................................................................................................................ 13

ETSI
---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 302 264 V2.1.1 (2017-02)

4.4.3.3 Limits .................................................................................................................................................... 13

4.4.3.4 Conformance ......................................................................................................................................... 13

4.4.4 Receiver sensitivity ..................................................................................................................................... 13

4.5 Other requirements and mitigation techniques ................................................................................................. 13

4.5.1 Installation requirements ............................................................................................................................. 13

4.5.1.1 Applicability.......................................................................................................................................... 13

4.5.1.2 Description ............................................................................................................................................ 14

4.5.1.3 Limits .................................................................................................................................................... 14

4.5.1.4 Conformance ......................................................................................................................................... 14

5 General considerations for performing the tests ..................................................................................... 14

6 Test setup and procedures ...................................................................................................................... 14

7 Conformance methods of measurement for transmitter and receiver ..................................................... 14

Annex A (informative): Relationship between the present document and the essential

requirements of Directive 2014/53/EU ......................................................... 15

Annex B (informative): Change History .............................................................................................. 16

History .............................................................................................................................................................. 17

ETSI
---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 302 264 V2.1.1 (2017-02)
Intellectual Property Rights

IPRs essential or potentially essential to the present document may have been declared to ETSI. The information

pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found

in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in

respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web

server (https://ipr.etsi.org/).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee

can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

server) which are, or may be, or may become, essential to the present document.
Foreword

This final draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee

Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the

ETSI standards EN Approval Procedure.

The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.7] to

provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation

of the laws of the Member States relating to the making available on the market of radio equipment and repealing

Directive 1999/5/EC [i.2].

Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with

the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present

document, a presumption of conformity with the corresponding essential requirements of that Directive and associated

EFTA regulations.

The present document covers short range radar equipment operating in the 77 GHz to 81 GHz range.

The present document covers the essential requirements of article 3.2 of the Directive 2014/53/EU [i.2].

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa

Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Modal verbs terminology

In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and

"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of

provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

Introduction

The present document, together with ETSI EN 303 396 [1], covers the assessment of certain types of equipment as

defined herein.
ETSI
---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 302 264 V2.1.1 (2017-02)
1 Scope

The present document specifies the technical requirements and methods of measurement for Short Range Devices (SRD)

working as broadband devices with at least 50 MHz occupied bandwidth in the 77 GHz to 81 GHz frequency range,

intended for Transport and Traffic Telematics (TTT) applications. Applications include but are not limited to e.g. Short

Range Radar (SRR) for obstacle detection, stop&go, blind spot detection, parking aid, backup aid and precrash.

The present document covers transmitters intended to operate in the frequency range as defined in the EC Decision

2004/545/EC [i.5] and the ECC Decision ECC/DEC/(04)03 [i.6].
The present document:

a) contains the technical characteristics and test methods for short range radar equipment fitted with integral

antennas operating in 77 GHz to 81 GHz range;

b) covers short range radar vehicle applications in the 77 GHz to 81 GHz range. It covers integrated transceivers

and separate transmit/receive modules;

c) integrated multi-mode transceivers [i.9], transmitters and receivers in the 76 GHz to 77 GHz range which

comply with ETSI EN 301 091-1 [i.8] and which use the 77 GHz to 81 GHz range for one or several operation

modes, within one EUT cycle or in different vehicle operation modes.

For such sensors, the 77 GHz to 81 GHz operation modes should be available for testing separately from the

76 GHz to 77 GHz operation modes.

The present document does not necessarily include all the characteristics which may be required by a user, nor does it

necessarily represent the optimum performance achievable.

In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present

document and ETSI EN 303 396 [1], the provisions of the present document take precedence.

These radio equipment types are capable of operating in all or part of the frequency bands given in table 1.

Table 1: Permitted ranges of operation
Permitted ranges of operation
Transmit 77 GHz to 81 GHz
Receive 77 GHz to 81 GHz

The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU [i.2] under the

conditions identified in annex A.
2 References
2.1 Normative references

References are specific, identified by date of publication and/or edition number or version number. Only the cited

version applies.

Referenced documents which are not found to be publicly available in the expected location might be found at

https://docbox.etsi.org/Reference/.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are necessary for the application of the present document.

[1] ETSI EN 303 396 (V1.1.1) (12-2016): "Short Range Devices; Measurement Techniques for

automotive and surveillance radar equipment".
ETSI
---------------------- Page: 6 ---------------------
...

Draft ETSI EN 302 264 V2.1.0 (2016-07)
HARMONISED EUROPEAN STANDARD
Short Range Devices;
Transport and Traffic Telematics (TTT);
Short Range Radar equipment operating in
the 77 GHz to 81 GHz band;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 302 264 V2.1.0 (2016-07)
Reference
REN/ERM-TGSRR-76
Keywords
radar, radio, RTTT, SRD, testing, UWB
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search

The present document may be made available in electronic versions and/or in print. The content of any electronic and/or

print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any

existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the

print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.

Users of the present document should be aware that the document may be subject to revision or change of status.

Information on the current status of this and other ETSI documents is available at

https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx

If you find errors in the present document, please send your comment to one of the following services:

https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification

No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying

and microfilm except as authorized by written permission of ETSI.

The content of the PDF version shall not be modified without the written authorization of ETSI.

The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM

DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.

3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and

of the 3GPP Organizational Partners.

GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.

ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 302 264 V2.1.0 (2016-07)
Contents

Intellectual Property Rights ................................................................................................................................ 5

Foreword ............................................................................................................................................................. 5

Modal verbs terminology .................................................................................................................................... 5

Introduction ........................................................................................................................................................ 6

1 Scope ........................................................................................................................................................ 7

2 References ................................................................................................................................................ 7

2.1 Normative references ......................................................................................................................................... 7

2.2 Informative references ........................................................................................................................................ 8

3 Definitions, symbols and abbreviations ................................................................................................... 8

3.1 Definitions .......................................................................................................................................................... 8

3.2 Symbols .............................................................................................................................................................. 8

3.3 Abbreviations ..................................................................................................................................................... 9

4 Technical requirements specifications ..................................................................................................... 9

4.1 Environmental conditions ................................................................................................................................... 9

4.2 General ............................................................................................................................................................... 9

4.2.1 Background information ............................................................................................................................... 9

4.2.2 Wanted performance criteria......................................................................................................................... 9

4.2.3 Fixed and scanning antennas ...................................................................................................................... 10

4.3 Transmitter Conformance Requirements .......................................................................................................... 10

4.3.1 Operating Frequency Range ....................................................................................................................... 10

4.3.1.1 Applicability.......................................................................................................................................... 10

4.3.1.2 Description ............................................................................................................................................ 10

4.3.1.3 Limits .................................................................................................................................................... 10

4.3.1.4 Conformance ......................................................................................................................................... 10

4.3.2 Mean Power spectral density ...................................................................................................................... 10

4.3.2.1 Applicability.......................................................................................................................................... 10

4.3.2.2 Description ............................................................................................................................................ 10

4.3.2.3 Limits .................................................................................................................................................... 10

4.3.2.4 Conformance ......................................................................................................................................... 11

4.3.3 Peak Power ................................................................................................................................................. 11

4.3.3.1 Applicability.......................................................................................................................................... 11

4.3.3.2 Description ............................................................................................................................................ 11

4.3.3.3 Limits .................................................................................................................................................... 11

4.3.3.4 Conformance ......................................................................................................................................... 11

4.3.4 Unwanted emissions in the out-of-band domain ......................................................................................... 11

4.3.4.1 Applicability.......................................................................................................................................... 11

4.3.4.2 Description ............................................................................................................................................ 11

4.3.4.3 Limits .................................................................................................................................................... 11

4.3.4.4 Conformance ......................................................................................................................................... 12

4.3.5 Unwanted emissions in the spurious domain .............................................................................................. 12

4.3.5.1 Applicability.......................................................................................................................................... 12

4.3.5.2 Description ............................................................................................................................................ 12

4.3.5.3 Limits .................................................................................................................................................... 12

4.3.5.4 Conformance ......................................................................................................................................... 12

4.4 Receiver Conformance Requirements .............................................................................................................. 12

4.4.1 Introduction................................................................................................................................................. 12

4.4.2 Receiver spurious emissions ....................................................................................................................... 13

4.4.2.1 Applicability.......................................................................................................................................... 13

4.4.2.2 Description ............................................................................................................................................ 13

4.4.2.3 Limits .................................................................................................................................................... 13

4.4.2.4 Conformance ......................................................................................................................................... 13

4.4.3 Receiver in-band, out-of-band and remote-band signals handling.............................................................. 13

4.4.3.1 Applicability.......................................................................................................................................... 13

4.4.3.2 Description ............................................................................................................................................ 13

ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 302 264 V2.1.0 (2016-07)

4.4.3.3 Limits .................................................................................................................................................... 14

4.4.3.4 Conformance ......................................................................................................................................... 14

4.4.4 Receiver sensitivity ..................................................................................................................................... 14

4.5 Other requirements and mitigation techniques ................................................................................................. 14

4.5.1 Installation requirements ............................................................................................................................. 14

4.5.1.1 Applicability.......................................................................................................................................... 14

4.5.1.2 Description ............................................................................................................................................ 14

4.5.1.3 Limits .................................................................................................................................................... 14

4.5.1.4 Conformance ......................................................................................................................................... 14

5 General considerations for performing the tests ..................................................................................... 15

6 Test setup and procedures ...................................................................................................................... 15

7 Conformance methods of measurement for transmitter and receiver ..................................................... 15

Annex A (normative): Relationship between the present document and the essential

requirements of Directive 2014/53/EU ......................................................... 16

Annex B (informative): Bibliography ................................................................................................... 17

Annex C (informative): Change History .............................................................................................. 18

History .............................................................................................................................................................. 19

ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 302 264 V2.1.0 (2016-07)
Intellectual Property Rights

IPRs essential or potentially essential to the present document may have been declared to ETSI. The information

pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found

in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in

respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web

server (https://ipr.etsi.org/).

Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee

can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

server) which are, or may be, or may become, essential to the present document.
Foreword

This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic

compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote

phase of the ETSI standards EN Approval Procedure.

The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.7] to

provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation

of the laws of the Member States relating to the making available on the market of radio equipment and repealing

Directive 1999/5/EC [i.2].

Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with

the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present

document, a presumption of conformity with the corresponding essential requirements of that Directive and associated

EFTA regulations.

The present document covers short range radar equipment operating in the 77 GHz to 81 GHz range.

The present document covers the essential requirements of article 3.2 of the RE-D [i.2].

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication

Date of latest publication of new National Standard or endorsement of this EN 6 months after doa

(dop/e):

Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Modal verbs terminology

In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and

"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of

provisions).

"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 302 264 V2.1.0 (2016-07)
Introduction

The present document, together with ETSI EN 303 396 [1], covers the assessment of certain types of equipment as

defined herein.

In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present

document and ETSI EN 303 396 [1], the provisions of the present document take precedence.

ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 302 264 V2.1.0 (2016-07)
1 Scope

The present document specifies the technical requirements and methods of measurement for Short Range Devices (SRD)

working as broadband devices with at least 50 MHz occupied bandwidth in the 77 GHz to 81 GHz frequency range,

hereinafter referred to as the 79 GHz band, intended for Transport and Traffic Telematics (TTT) applications.

Applications include but are not limited to e.g. Short Range Radar (SRR) for obstacle detection, stop&go, blind spot

detection, parking aid, backup aid and precrash.

The present document covers transmitters intended to operate in the frequency range as defined in the EC Decision

2004/545/EC [i.5] and the ECC Decision ECC/DEC/(04)03 [i.6].
The presentdocument applies to:
a) transmitters in the 79 GHz range operating as broadband devices;
b) receivers operating in the 79 GHz range;
c) integrated transceivers in the 79 GHz range.
The present document:

a) contains the technical characteristics and test methods for short range radar equipment fitted with integral

antennas operating in the 79 GHz range;

b) covers short range radar vehicle applications in the 79 GHz range. It covers integrated transceivers and

separate transmit/receive modules.

The present document does not necessarily include all the characteristics which may be required by a user, nor does it

necessarily represent the optimum performance achievable.

These radio equipment types are capable of operating in all or part of the frequency bands given in table 1.

Table 1: Permitted ranges of operation
Permitted ranges of operation
Transmit 77 GHz to 81 GHz
Receive 77 GHz to 81 GHz

The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the

efficient use of radio spectrum in order to avoid harmful interference.
2 References
2.1 Normative references

References are either specific (identified by date of publication and/or edition number or version number) or

non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the

referenced document (including any amendments) applies.

Referenced documents which are not found to be publicly available in the expected location might be found at

http://docbox.etsi.org/Reference.

NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee

their long term validity.

The following referenced documents are necessary for the application of the present document.

[1] ETSI EN 303 396 (V1.1.0) (04-2016): "Short Range Devices; Measurement Techniqu

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.