SIST EN 300 674-2-2 V2.2.1:2019
(Main)Transport and Traffic Telematics (TTT) - Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the 5 795 MHz to 5 815 MHz frequency band - Part 2: Harmonised Standard for access to radio spectrum - Sub-part 2: On-Board Units (OBU)
Transport and Traffic Telematics (TTT) - Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the 5 795 MHz to 5 815 MHz frequency band - Part 2: Harmonised Standard for access to radio spectrum - Sub-part 2: On-Board Units (OBU)
The present document specifies technical characteristics and methods of measurements for Transport and Traffic
Telematics (TTT) systems:
• with a Radio Frequency (RF) output connection and specified antenna or with an integral antenna;
• for data transmission only;
• operating in the 5 795 MHz to 5 815 MHz frequency band.
The applicability of the present document covers only the On Board Units (OBU).
The present document complies with the Commission Implementing Decision 2017/1483/EU [i.4] and CEPT/ERC
Recommendation 70-03 [i.6].
Transportna in prometna telematika (TTT) - Oddajniška oprema za enouporabniško (osebno) komunikacijo kratkega dosega (DSRC) (s prenosnima hitrostma 500 kbit/s / 250 kbit/s), ki deluje v frekvenčnem pasu od 5795 MHz do 5815 MHz - 2. del: Harmonizirani standard za dostop do radijskega spektra - 2. poddel: Enote na vozilu (OBU)
Ta dokument določa tehnične karakteristike in merilne metode za sisteme transportne in prometne telematike (TTT):
• z radiofrekvenčno (RF) izhodno povezavo in ustrezno anteno ali z vgrajeno anteno;
• samo za prenos podatkov;
• ki delujejo v frekvenčnem pasu od 5795 MHz do 5815 MHz.
Uporaba tega dokumenta zajema samo enote v vozilu (OBU).
Ta dokument je skladen z Izvedbenim sklepom Komisije 2017/1483/EU [i.4] in s priporočilom CEPT/ERC 70-03 [i.6].
General Information
Buy Standard
Standards Content (Sample)
ETSI EN 300 674-2-2 V2.2.1 (2019-06)
HARMONISED EUROPEAN STANDARD
Transport and Traffic Telematics (TTT);
Dedicated Short Range Communication (DSRC)
transmission equipment (500 kbit/s / 250 kbit/s)
operating in the 5 795 MHz to 5 815 MHz frequency band;
Part 2: Harmonised Standard for access to radio spectrum;
Sub-part 2: On-Board Units (OBU)
---------------------- Page: 1 ----------------------
2 ETSI EN 300 674-2-2 V2.2.1 (2019-06)
Reference
REN/ERM-TG37-272
Keywords
data, DSRC, harmonised standard, radio,
regulation, RTTT, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 300 674-2-2 V2.2.1 (2019-06)
Contents
Intellectual Property Rights . 6
Foreword . 6
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 11
3.3 Abbreviations . 13
4 Technical requirements specifications . 14
4.1 General characteristics . 14
4.1.1 OBU sets . 14
4.1.2 Uplink sub-carrier frequencies . 14
4.1.3 Carrier frequencies . 14
4.1.4 Modulation . 14
4.2 Environmental conditions . 15
4.2.1 Environmental profile . 15
4.2.2 Power supply . 15
4.3 Conformance requirements . 15
4.3.1 Transmitter requirements . 15
4.3.1.1 Transmitter spectrum mask . 15
4.3.1.2 Maximum equivalent isotropically radiated power . 15
4.3.1.3 Transmitter frequency error . 16
4.3.1.4 Transmitter unwanted emissions . 16
4.3.2 Receiver requirements . 16
4.3.2.1 Receiver unwanted emissions in the spurious domain . 16
4.3.2.2 Sensitivity . 17
4.3.2.3 Receiver selectivity . 17
4.3.2.3.1 General . 17
4.3.2.3.2 Receiver spurious response rejection and adjacent channel rejection . 17
4.3.2.3.3 Receiver blocking . 18
4.3.2.3.4 Co-channel rejection . 18
4.3.3 Antennas . 18
5 Testing for compliance with technical requirements . 19
5.1 Environmental conditions for testing . 19
5.2 Interpretation of the measurement results . 19
5.3 Radio test suites . 20
5.3.1 Transmitter parameters . 20
5.3.1.1 Transmitter spectrum mask . 20
5.3.1.1.1 General . 20
5.3.1.1.2 Radiated measurements . 20
5.3.1.1.3 Conducted measurements . 22
5.3.1.2 Maximum equivalent isotropically radiated power . 23
5.3.1.2.1 General . 23
5.3.1.2.2 Radiated measurement . 24
5.3.1.2.3 Conducted measurement. 25
5.3.1.3 Transmitter frequency error . 25
5.3.1.3.1 General . 25
5.3.1.3.2 Radiated measurements . 26
5.3.1.3.3 Conducted measurements . 26
5.3.1.4 Transmitter unwanted emissions . 27
5.3.1.4.1 General . 27
5.3.1.4.2 Radiated measurement . 27
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 300 674-2-2 V2.2.1 (2019-06)
5.3.2 Receiver parameters . 28
5.3.2.1 Receiver unwanted emissions in the spurious domain . 28
5.3.2.1.1 General . 28
5.3.2.1.2 Radiated measurement . 28
5.3.2.2 Sensitivity . 29
5.3.2.2.1 General . 29
5.3.2.2.2 Radiated measurements . 29
5.3.2.2.3 Conducted measurements . 29
5.3.2.3 Receiver selectivity . 30
5.3.2.3.1 General . 30
5.3.2.3.2 Unwanted signal characteristics . 30
5.3.2.3.3 Measurement of receiver selectivity in OBU boresight . 30
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 32
Annex B (normative): Basics on testing . 33
B.1 General conditions . 33
B.1.1 Thermal balance . 33
B.1.2 Test signals . 33
B.1.3 Test sites . 34
B.1.3.1 Shielded anechoic chamber. 34
B.1.3.2 Open area test site . 35
B.1.3.3 Test fixture . 35
B.1.4 General requirements for RF cables . 36
B.1.5 Conducted measurements . 37
B.1.5.1 One antenna connector arrangement . 37
B.1.5.2 Two antenna connectors arrangement. 38
B.1.5.3 Test site requirements . 38
B.1.5.4 Site preparation for conducted measurements . 38
B.1.5.4.1 Monochromatic signals . 38
B.1.5.4.2 Modulated signals . 38
B.1.6 Radiated measurements . 39
B.1.6.1 One antenna arrangement . 39
B.1.6.2 Two antennas arrangement . 40
B.1.6.3 Test site requirements . 41
B.1.6.3.1 Measurement distances . 41
B.1.6.3.2 Free-space wave propagation . 41
B.1.6.4 Test and substitution antennas . 42
B.1.6.5 Site preparation for radiated OBU measurements . 42
B.1.6.5.1 Monochromatic signals . 42
B.1.6.5.2 Modulated signals . 44
B.1.6.5.3 Arrangement for OBU transmitter unwanted emissions measurement . 45
B.1.6.5.4 Arrangement for OBU receiver selectivity measurement . 47
B.2 Instruments . 49
B.2.1 Receiving device . 49
B.2.2 RF power sensor . 49
B.2.3 Combiner . 50
B.3 Power of modulated RSU carrier . 50
B.4 Bit error ratio measurements . 51
B.4.1 Basics . 51
B.4.2 BER measurement . 51
B.4.3 FER measurement . 51
B.4.3.1 Mathematical expressions . 51
B.4.3.2 Equipment . 52
B.4.3.3 Procedure . 52
Annex C (normative): Environmental profile . 53
C.1 General Requirements . 53
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 300 674-2-2 V2.2.1 (2019-06)
C.2 Mandatory environmental conditions . 53
C.3 Additional environmental conditions . 53
Annex D (informative): Maximum Measurement Uncertainty . 54
Annex E (informative): Bibliography . 55
Annex F (informative): Change History . 56
History . 57
ETSI
---------------------- Page: 5 ----------------------
6 ETSI EN 300 674-2-2 V2.2.1 (2019-06)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.3] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.2].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 2, sub-part 2 of a multi-part deliverable covering Transport and Traffic Telematics (TTT);
Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the
5 795 MHz to 5 815 MHz frequency band, as identified below:
Part 1: "General characteristics and test methods for Road Side Units (RSU) and On-Board Units (OBU)";
Part 2: "Harmonised Standard for access to radio spectrum";
Sub-part 1: "Road Side Units (RSU)";
Sub-part 2: "On-Board Units (OBU)".
National transposition dates
Date of adoption of this EN: 17 June 2019
Date of latest announcement of this EN (doa): 30 September 2019
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 March 2020
Date of withdrawal of any conflicting National Standard (dow): 31 March 2021
ETSI
---------------------- Page: 6 ----------------------
7 ETSI EN 300 674-2-2 V2.2.1 (2019-06)
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 7 ----------------------
8 ETSI EN 300 674-2-2 V2.2.1 (2019-06)
1 Scope
The present document specifies technical characteristics and methods of measurements for Transport and Traffic
Telematics (TTT) systems:
• with a Radio Frequency (RF) output connection and specified antenna or with an integral antenna;
• for data transmission only;
• operating in the 5 795 MHz to 5 815 MHz frequency band.
The applicability of the present document covers only the On Board Units (OBU).
The present document complies with the Commission Implementing Decision 2017/1483/EU [i.4] and CEPT/ERC
Recommendation 70-03 [i.6].
The present document applies to the following radio equipment types operating in all or in part of the following service
frequency bands given in table 1.
Table 1: Frequency bands and centre frequencies f allocated for DSRC
Tx
Pan European Service Frequencies National Service Frequencies
Channel 1 5,795 GHz to 5,800 GHz, f = 5,7975 GHz
Tx
Channel 2 5,800 GHz to 5,805 GHz, f = 5,8025 GHz
Tx
Channel 3 5,805 GHz to 5,810 GHz, f = 5,8075 GHz
Tx
Channel 4 5,810 GHz to 5,815 GHz, f = 5,8125 GHz
Tx
NOTE: The relationship between the present document and essential requirements of article 3.2 of
Directive 2014/53/EU [i.2] is given in annex A.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] CEN EN 12253 (2004): "Road transport and traffic telematics - Dedicated short-range
communication - Physical layer using microwave at 5,8 GHz".
[2] ISO 14906 (2018): "Electronic fee collection -- Application interface definition for dedicated
short-range communication".
[3] CEPT/ERC Recommendation 74-01E (2011): "Unwanted emissions in the spurious domain".
[4] CEN EN 13372 (2004): "Road Transport and Traffic Telematics (RTTT) - Dedicated short-range
communication - Profiles for RTTT applications".
ETSI
---------------------- Page: 8 ----------------------
9 ETSI EN 300 674-2-2 V2.2.1 (2019-06)
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI TS 103 052 (V1.1.1) (03-2011): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Radiated measurement methods and general arrangements for test sites up to 100 GHz".
[i.2] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.3] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
[i.4] Commission Implementing Decision (EU) 2017/1483 of 8 August 2017 amending Decision
2006/771/EC on harmonisation of the radio spectrum for use by short-range devices and repealing
Decision 2006/804/EC" .
[i.5] Void.
[i.6] CEPT/ERC Recommendation 70-03 (May 2018): "Relating to the use of Short Range Devices
(SRD)".
[i.7] ETSI TR 102 273-2 (V1.2.1) (12-2001): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Improvement on Radiated Methods of Measurement (using test site) and
evaluation of the corresponding measurement uncertainties; Part 2: Anechoic chamber".
[i.8] ETSI TR 102 273-6 (V1.2.1) (12-2001): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Improvement on Radiated Methods of Measurement (using test site) and
evaluation of the corresponding measurement uncertainties; Part 6: Test fixtures".
[i.9] IEC 60721-3-4 (1995) including Amendment 1 (1996): "Classification of environmental
conditions - Part 3: Classification of groups of environmental parameters and their severities -
Section 4: Stationary use at non-weather protected locations".
[i.10] IEC 60721-3-5 (1997): "Classification of environmental conditions - Part 3: Classification of
groups of environmental parameters and their severities - Section 5: Ground vehicle installations".
3 Definition of t
...
Draft ETSI EN 300 674-2-2 V2.2.0 (2019-03)
HARMONISED EUROPEAN STANDARD
Transport and Traffic Telematics (TTT);
Dedicated Short Range Communication (DSRC)
transmission equipment (500 kbit/s / 250 kbit/s)
operating in the 5 795 MHz to 5 815 MHz frequency band;
Part 2: Harmonised Standard for access to radio spectrum;
Sub-part 2: On-Board Units (OBU)
---------------------- Page: 1 ----------------------
2 Draft ETSI EN 300 674-2-2 V2.2.0 (2019-03)
Reference
REN/ERM-TG37-272
Keywords
data, DSRC, harmonised standard, radio,
regulation, RTTT, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 Draft ETSI EN 300 674-2-2 V2.2.0 (2019-03)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 11
3.3 Abbreviations . 13
4 Technical requirements specifications . 14
4.1 General characteristics . 14
4.1.1 OBU sets . 14
4.1.2 Uplink sub-carrier frequencies . 14
4.1.3 Carrier frequencies . 14
4.1.4 Modulation . 14
4.2 Environmental conditions . 15
4.2.1 Environmental profile . 15
4.2.2 Power supply . 15
4.3 Conformance requirements . 15
4.3.1 Transmitter requirements . 15
4.3.1.1 Transmitter spectrum mask . 15
4.3.1.2 Maximum equivalent isotropically radiated power . 15
4.3.1.3 Transmitter frequency error . 16
4.3.1.4 Transmitter unwanted emissions . 16
4.3.2 Receiver requirements . 16
4.3.2.1 Receiver unwanted emissions in the spurious domain . 16
4.3.2.2 Sensitivity . 17
4.3.2.3 Receiver selectivity . 17
4.3.2.3.1 General . 17
4.3.2.3.2 Receiver spurious response rejection and adjacent channel rejection . 17
4.3.2.3.3 Receiver blocking . 18
4.3.2.3.4 Co-channel rejection . 18
4.3.3 Antennas . 18
5 Testing for compliance with technical requirements . 19
5.1 Environmental conditions for testing . 19
5.2 Interpretation of the measurement results . 19
5.3 Radio test suites . 20
5.3.1 Transmitter parameters . 20
5.3.1.1 Transmitter spectrum mask . 20
5.3.1.1.1 General . 20
5.3.1.1.2 Radiated measurements . 20
5.3.1.1.3 Conducted measurements . 22
5.3.1.2 Maximum equivalent isotropically radiated power . 23
5.3.1.2.1 General . 23
5.3.1.2.2 Radiated measurement . 24
5.3.1.2.3 Conducted measurement. 25
5.3.1.3 Transmitter frequency error . 25
5.3.1.3.1 General . 25
5.3.1.3.2 Radiated measurements . 26
5.3.1.3.3 Conducted measurements . 26
5.3.1.4 Transmitter unwanted emissions . 27
5.3.1.4.1 General . 27
ETSI
---------------------- Page: 3 ----------------------
4 Draft ETSI EN 300 674-2-2 V2.2.0 (2019-03)
5.3.1.4.2 Radiated measurement . 27
5.3.2 Receiver parameters . 28
5.3.2.1 Receiver unwanted emissions in the spurious domain . 28
5.3.2.1.1 General . 28
5.3.2.1.2 Radiated measurement . 28
5.3.2.2 Sensitivity . 29
5.3.2.2.1 General . 29
5.3.2.2.2 Radiated measurements . 29
5.3.2.2.3 Conducted measurements . 29
5.3.2.3 Receiver selectivity . 30
5.3.2.3.1 General . 30
5.3.2.3.2 Unwanted signal characteristics . 30
5.3.2.3.3 Measurement of receiver selectivity in OBU boresight . 30
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 32
Annex B (normative): Basics on testing . 33
B.1 General conditions . 33
B.1.1 Thermal balance . 33
B.1.2 Test signals . 33
B.1.3 Test sites . 34
B.1.3.1 Shielded anechoic chamber. 34
B.1.3.2 Open area test site . 35
B.1.3.3 Test fixture . 35
B.1.4 General requirements for RF cables . 36
B.1.5 Conducted measurements . 37
B.1.5.1 One antenna connector arrangement . 37
B.1.5.2 Two antenna connectors arrangement. 38
B.1.5.3 Test site requirements . 38
B.1.5.4 Site preparation for conducted measurements . 38
B.1.5.4.1 Monochromatic signals . 38
B.1.5.4.2 Modulated signals . 38
B.1.6 Radiated measurements . 39
B.1.6.1 One antenna arrangement . 39
B.1.6.2 Two antennas arrangement . 40
B.1.6.3 Test site requirements . 41
B.1.6.3.1 Measurement distances . 41
B.1.6.3.2 Free-space wave propagation . 41
B.1.6.4 Test and substitution antennas . 42
B.1.6.5 Site preparation for radiated OBU measurements . 42
B.1.6.5.1 Monochromatic signals . 42
B.1.6.5.2 Modulated signals . 44
B.1.6.5.3 Arrangement for OBU transmitter unwanted emissions measurement . 45
B.1.6.5.4 Arrangement for OBU receiver selectivity measurement . 47
B.2 Instruments . 49
B.2.1 Receiving device . 49
B.2.2 RF power sensor . 49
B.2.3 Combiner . 50
B.3 Power of modulated RSU carrier . 50
B.4 Bit error ratio measurements . 51
B.4.1 Basics . 51
B.4.2 BER measurement . 51
B.4.3 FER measurement . 51
B.4.3.1 Mathematical expressions . 51
B.4.3.2 Equipment . 52
B.4.3.3 Procedure . 52
Annex C (normative): Environmental profile . 53
ETSI
---------------------- Page: 4 ----------------------
5 Draft ETSI EN 300 674-2-2 V2.2.0 (2019-03)
C.1 General Requirements . 53
C.2 Mandatory environmental conditions . 53
C.3 Additional environmental conditions . 53
Annex D (informative): Maximum Measurement Uncertainty . 54
Annex E (informative): Bibliography . 55
Annex F (informative): Change History . 56
History . 57
ETSI
---------------------- Page: 5 ----------------------
6 Draft ETSI EN 300 674-2-2 V2.2.0 (2019-03)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.3] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.2].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 2, sub-part 2 of a multi-part deliverable covering Transport and Traffic Telematics (TTT);
Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the
5 795 MHz to 5 815 MHz frequency band, as identified below:
Part 1: "General characteristics and test methods for Road Side Units (RSU) and On-Board Units (OBU)";
Part 2: "Harmonised Standard for access to radio spectrum";
Sub-part 1: "Road Side Units (RSU)";
Sub-part 2: "On-Board Units (OBU)".
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
ETSI
---------------------- Page: 6 ----------------------
7 Draft ETSI EN 300 674-2-2 V2.2.0 (2019-03)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 7 ----------------------
8 Draft ETSI EN 300 674-2-2 V2.2.0 (2019-03)
1 Scope
The present document specifies technical characteristics and methods of measurements for Transport and Traffic
Telematics (TTT) systems:
• with a Radio Frequency (RF) output connection and specified antenna or with an integral antenna;
• for data transmission only;
• operating in the 5 795 MHz to 5 815 MHz frequency band.
The applicability of the present document covers only the On Board Units (OBU).
The present document complies with the Commission Implementing Decision 2017/1483/EU [i.4] and CEPT/ERC
Recommendation 70-03 [i.6].
The present document applies to the following radio equipment types operating in all or in part of the following service
frequency bands given in table 1.
Table 1: Frequency bands and centre frequencies f allocated for DSRC
Tx
Pan European Service Frequencies National Service Frequencies
Channel 1 5,795 GHz to 5,800 GHz, f = 5,7975 GHz
Tx
Channel 2 5,800 GHz to 5,805 GHz, f = 5,8025 GHz
Tx
Channel 3 5,805 GHz to 5,810 GHz, f = 5,8075 GHz
Tx
Channel 4 5,810 GHz to 5,815 GHz, f = 5,8125 GHz
Tx
NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.2] is given in annex A.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] CEN EN 12253 (2004): "Road transport and traffic telematics - Dedicated short-range
communication - Physical layer using microwave at 5,8 GHz".
[2] ISO 14906 (2018): "Electronic fee collection -- Application interface definition for dedicated
short-range communication".
[3] CEPT/ERC Recommendation 74-01E (2011): "Unwanted emissions in the spurious domain".
[4] CEN EN 13372 (2004): "Road Transport and Traffic Telematics (RTTT) - Dedicated short-range
communication - Profiles for RTTT applications".
ETSI
---------------------- Page: 8 ----------------------
9 Draft ETSI EN 300 674-2-2 V2.2.0 (2019-03)
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI TS 103 052 (V1.1.1) (03-2011): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Radiated measurement methods and general arrangements for test sites up to 100 GHz".
[i.2] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.3] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
[i.4] Commission Implementing Decision (EU) 2017/1483 of 8 August 2017 amending Decision
2006/771/EC on harmonisation of the radio spectrum for use by short-range devices and repealing
Decision 2006/804/EC" .
[i.5] Void.
[i.6] CEPT/ERC Recommendation 70-03 (May 2018): "Relating to the use of Short Range Devices
(SRD)".
[i.7] ETSI TR 102 273-2 (V1.2.1) (12-2001): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Improvement on Radiated Methods of Measurement (using test site) and
evaluation of the corresponding measurement uncertainties; Part 2: Anechoic chamber".
[i.8] ETSI TR 102 273-6 (V1.2.1) (12-2001): "Electromagnetic compatibility and Radio spectrum
Matters (ERM); Improvement on Radiated Methods of Measurement (using test site) and
evaluation of the corresponding measurement uncertainties; Part 6: Test fixtures".
[i.9] IEC 60721-3-4 (1995) including Amendment 1 (1996): "Classification of environmental
conditions - Part 3: C
...
SLOVENSKI STANDARD
SIST EN 300 674-2-2 V2.2.1:2019
01-september-2019
Transportna in prometna telematika (TTT) - Oddajniška oprema za enouporabniško
(osebno) komunikacijo kratkega dosega (DSRC) (s prenosnima hitrostma 500
kbit/s / 250 kbit/s), ki deluje v frekvenčnem pasu od 5795 MHz do 5815 MHz - 2. del:
Harmonizirani standard za dostop do radijskega spektra - 2. poddel: Enote na
vozilu (OBU)
Transport and Traffic Telematics (TTT) - Dedicated Short Range Communication
(DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the 5 795 MHz to 5
815 MHz frequency band - Part 2: Harmonised Standard for access to radio spectrum -
Sub-part 2: On-Board Units (OBU)
Ta slovenski standard je istoveten z: ETSI EN 300 674-2-2 V2.2.1 (2019-06)
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
35.240.60 Uporabniške rešitve IT v IT applications in transport
prometu
43.040.15 Avtomobilska informatika. Car informatics. On board
Vgrajeni računalniški sistemi computer systems
SIST EN 300 674-2-2 V2.2.1:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 300 674-2-2 V2.2.1:2019
---------------------- Page: 2 ----------------------
SIST EN 300 674-2-2 V2.2.1:2019
ETSI EN 300 674-2-2 V2.2.1 (2019-06)
HARMONISED EUROPEAN STANDARD
Transport and Traffic Telematics (TTT);
Dedicated Short Range Communication (DSRC)
transmission equipment (500 kbit/s / 250 kbit/s)
operating in the 5 795 MHz to 5 815 MHz frequency band;
Part 2: Harmonised Standard for access to radio spectrum;
Sub-part 2: On-Board Units (OBU)
---------------------- Page: 3 ----------------------
SIST EN 300 674-2-2 V2.2.1:2019
2 ETSI EN 300 674-2-2 V2.2.1 (2019-06)
Reference
REN/ERM-TG37-272
Keywords
data, DSRC, harmonised standard, radio,
regulation, RTTT, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 300 674-2-2 V2.2.1:2019
3 ETSI EN 300 674-2-2 V2.2.1 (2019-06)
Contents
Intellectual Property Rights . 6
Foreword . 6
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 11
3.3 Abbreviations . 13
4 Technical requirements specifications . 14
4.1 General characteristics . 14
4.1.1 OBU sets . 14
4.1.2 Uplink sub-carrier frequencies . 14
4.1.3 Carrier frequencies . 14
4.1.4 Modulation . 14
4.2 Environmental conditions . 15
4.2.1 Environmental profile . 15
4.2.2 Power supply . 15
4.3 Conformance requirements . 15
4.3.1 Transmitter requirements . 15
4.3.1.1 Transmitter spectrum mask . 15
4.3.1.2 Maximum equivalent isotropically radiated power . 15
4.3.1.3 Transmitter frequency error . 16
4.3.1.4 Transmitter unwanted emissions . 16
4.3.2 Receiver requirements . 16
4.3.2.1 Receiver unwanted emissions in the spurious domain . 16
4.3.2.2 Sensitivity . 17
4.3.2.3 Receiver selectivity . 17
4.3.2.3.1 General . 17
4.3.2.3.2 Receiver spurious response rejection and adjacent channel rejection . 17
4.3.2.3.3 Receiver blocking . 18
4.3.2.3.4 Co-channel rejection . 18
4.3.3 Antennas . 18
5 Testing for compliance with technical requirements . 19
5.1 Environmental conditions for testing . 19
5.2 Interpretation of the measurement results . 19
5.3 Radio test suites . 20
5.3.1 Transmitter parameters . 20
5.3.1.1 Transmitter spectrum mask . 20
5.3.1.1.1 General . 20
5.3.1.1.2 Radiated measurements . 20
5.3.1.1.3 Conducted measurements . 22
5.3.1.2 Maximum equivalent isotropically radiated power . 23
5.3.1.2.1 General . 23
5.3.1.2.2 Radiated measurement . 24
5.3.1.2.3 Conducted measurement. 25
5.3.1.3 Transmitter frequency error . 25
5.3.1.3.1 General . 25
5.3.1.3.2 Radiated measurements . 26
5.3.1.3.3 Conducted measurements . 26
5.3.1.4 Transmitter unwanted emissions . 27
5.3.1.4.1 General . 27
5.3.1.4.2 Radiated measurement . 27
ETSI
---------------------- Page: 5 ----------------------
SIST EN 300 674-2-2 V2.2.1:2019
4 ETSI EN 300 674-2-2 V2.2.1 (2019-06)
5.3.2 Receiver parameters . 28
5.3.2.1 Receiver unwanted emissions in the spurious domain . 28
5.3.2.1.1 General . 28
5.3.2.1.2 Radiated measurement . 28
5.3.2.2 Sensitivity . 29
5.3.2.2.1 General . 29
5.3.2.2.2 Radiated measurements . 29
5.3.2.2.3 Conducted measurements . 29
5.3.2.3 Receiver selectivity . 30
5.3.2.3.1 General . 30
5.3.2.3.2 Unwanted signal characteristics . 30
5.3.2.3.3 Measurement of receiver selectivity in OBU boresight . 30
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 32
Annex B (normative): Basics on testing . 33
B.1 General conditions . 33
B.1.1 Thermal balance . 33
B.1.2 Test signals . 33
B.1.3 Test sites . 34
B.1.3.1 Shielded anechoic chamber. 34
B.1.3.2 Open area test site . 35
B.1.3.3 Test fixture . 35
B.1.4 General requirements for RF cables . 36
B.1.5 Conducted measurements . 37
B.1.5.1 One antenna connector arrangement . 37
B.1.5.2 Two antenna connectors arrangement. 38
B.1.5.3 Test site requirements . 38
B.1.5.4 Site preparation for conducted measurements . 38
B.1.5.4.1 Monochromatic signals . 38
B.1.5.4.2 Modulated signals . 38
B.1.6 Radiated measurements . 39
B.1.6.1 One antenna arrangement . 39
B.1.6.2 Two antennas arrangement . 40
B.1.6.3 Test site requirements . 41
B.1.6.3.1 Measurement distances . 41
B.1.6.3.2 Free-space wave propagation . 41
B.1.6.4 Test and substitution antennas . 42
B.1.6.5 Site preparation for radiated OBU measurements . 42
B.1.6.5.1 Monochromatic signals . 42
B.1.6.5.2 Modulated signals . 44
B.1.6.5.3 Arrangement for OBU transmitter unwanted emissions measurement . 45
B.1.6.5.4 Arrangement for OBU receiver selectivity measurement . 47
B.2 Instruments . 49
B.2.1 Receiving device . 49
B.2.2 RF power sensor . 49
B.2.3 Combiner . 50
B.3 Power of modulated RSU carrier . 50
B.4 Bit error ratio measurements . 51
B.4.1 Basics . 51
B.4.2 BER measurement . 51
B.4.3 FER measurement . 51
B.4.3.1 Mathematical expressions . 51
B.4.3.2 Equipment . 52
B.4.3.3 Procedure . 52
Annex C (normative): Environmental profile . 53
C.1 General Requirements . 53
ETSI
---------------------- Page: 6 ----------------------
SIST EN 300 674-2-2 V2.2.1:2019
5 ETSI EN 300 674-2-2 V2.2.1 (2019-06)
C.2 Mandatory environmental conditions . 53
C.3 Additional environmental conditions . 53
Annex D (informative): Maximum Measurement Uncertainty . 54
Annex E (informative): Bibliography . 55
Annex F (informative): Change History . 56
History . 57
ETSI
---------------------- Page: 7 ----------------------
SIST EN 300 674-2-2 V2.2.1:2019
6 ETSI EN 300 674-2-2 V2.2.1 (2019-06)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.3] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.2].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 2, sub-part 2 of a multi-part deliverable covering Transport and Traffic Telematics (TTT);
Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the
5 795 MHz to 5 815 MHz frequency band, as identified below:
Part 1: "General characteristics and test methods for Road Side Units (RSU) and On-Board Units (OBU)";
Part 2: "Harmonised Standard for access to radio spectrum";
Sub-part 1: "Road Side Units (RSU)";
Sub-part 2: "On-Board Units (OBU)".
National transposition dates
Date of adoption of this EN: 17 June 2019
Date of latest announcement of this EN (doa): 30 September 2019
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 March 2020
Date of withdrawal of any conflicting National Standard (dow): 31 March 2021
ETSI
---------------------- Page: 8 ----------------------
SIST EN 300 674-2-2 V2.2.1:2019
7 ETSI EN 300 674-2-2 V2.2.1 (2019-06)
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 9 ----------------------
SIST EN 300 674-2-2 V2.2.1:2019
8 ETSI EN 300 674-2-2 V2.2.1 (2019-06)
1 Scope
The present document specifies technical characteristics and methods of measurements for Transport and Traffic
Telematics (TTT) systems:
• with a Radio Frequency (RF) output connection and specified antenna or with an integral antenna;
• for data transmission only;
• operating in the 5 795 MHz to 5 815 MHz frequency band.
The applicability of the present document covers only the On Board Units (OBU).
The present document complies with the Commission Implementing Decision 2017/1483/EU [i.4] and CEPT/ERC
Recommendation 70-03 [i.6].
The present document applies to the following radio equipment types operating in all or in part of the following service
frequency bands given in table 1.
Table 1: Frequency bands and centre frequencies f allocated for DSRC
Tx
Pan European Service Frequencies National Service Frequencies
Channel 1 5,795 GHz to 5,800 GHz, f = 5,7975 GHz
Tx
Channel 2 5,800 GHz to 5,805 GHz, f = 5,8025 GHz
Tx
Channel 3 5,805 GHz to 5,810 GHz, f = 5,8075 GHz
Tx
Channel 4 5,810 GHz to 5,815 GHz, f = 5,8125 GHz
Tx
NOTE: The relationship between the present document and essential requirements of article 3.2 of
Directive 2014/53/EU [i.2] is given in annex A.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] CEN EN 12253 (2004): "Road transport and traffic telematics - Dedicated short-range
communication - Physical layer using microwave at 5,8 GHz".
[2] ISO 14906 (2018): "Electronic fee collection -- Application interface definition for dedicated
short-range communication".
[3] CEPT/ERC Recommendation 74-01E (2011): "Unwanted emissions in the spurious domain".
[4] CEN EN 13372 (2004): "Road Transport and Traffic Telematics (RTTT) - Dedicated short-range
communication - Profiles for RTTT applications".
ETSI
---------------------- Page: 10 ----------------------
SIST EN 300 674-2-2 V2.2.1:2019
9 ETSI EN 300 674-2-2 V2.2.1 (2019-06)
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI TS 103 052 (V1.1.1) (03-2011): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Radiated measurement methods and general arrangements for test sites up to 100 GHz".
[i.2] Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.3] Commis
...
SLOVENSKI STANDARD
oSIST prEN 300 674-2-2 V2.2.0:2019
01-maj-2019
7UDQVSRUWQDLQSURPHWQDWHOHPDWLND 777 2GGDMQLãNDRSUHPD]DHQRXSRUDEQLãNR
RVHEQR NRPXQLNDFLMRNUDWNHJDGRVHJD '65& VSUHQRVQLPDKLWURVWPD
NELWVNELWV NLGHOXMHYIUHNYHQþQHPSDVXRG 0+]GR0+]GHO
+DUPRQL]LUDQLVWDQGDUG]DGRVWRSGRUDGLMVNHJDVSHNWUDSRGGHO (QRWHQD
YR]LOX 2%8
Transport and Traffic Telematics (TTT) - Dedicated Short Range Communication
(DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the 5 795 MHz to 5
815 MHz frequency band - Part 2: Harmonised Standard for access to radio spectrum -
Sub-part 2: On-Board Units (OBU)
Ta slovenski standard je istoveten z: ETSI EN 300 674-2-2 V2.2.0 (2019-03)
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
35.240.60 Uporabniške rešitve IT v IT applications in transport
prometu
43.040.15 $YWRPRELOVNDLQIRUPDWLND Car informatics. On board
9JUDMHQLUDþXQDOQLãNLVLVWHPL computer systems
oSIST prEN 300 674-2-2 V2.2.0:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 300 674-2-2 V2.2.0:2019
---------------------- Page: 2 ----------------------
oSIST prEN 300 674-2-2 V2.2.0:2019
Draft ETSI EN 300 674-2-2 V2.2.0 (2019-03)
HARMONISED EUROPEAN STANDARD
Transport and Traffic Telematics (TTT);
Dedicated Short Range Communication (DSRC)
transmission equipment (500 kbit/s / 250 kbit/s)
operating in the 5 795 MHz to 5 815 MHz frequency band;
Part 2: Harmonised Standard for access to radio spectrum;
Sub-part 2: On-Board Units (OBU)
---------------------- Page: 3 ----------------------
oSIST prEN 300 674-2-2 V2.2.0:2019
2 Draft ETSI EN 300 674-2-2 V2.2.0 (2019-03)
Reference
REN/ERM-TG37-272
Keywords
data, DSRC, harmonised standard, radio,
regulation, RTTT, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 300 674-2-2 V2.2.0:2019
3 Draft ETSI EN 300 674-2-2 V2.2.0 (2019-03)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 8
2.2 Informative references . 9
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 11
3.3 Abbreviations . 13
4 Technical requirements specifications . 14
4.1 General characteristics . 14
4.1.1 OBU sets . 14
4.1.2 Uplink sub-carrier frequencies . 14
4.1.3 Carrier frequencies . 14
4.1.4 Modulation . 14
4.2 Environmental conditions . 15
4.2.1 Environmental profile . 15
4.2.2 Power supply . 15
4.3 Conformance requirements . 15
4.3.1 Transmitter requirements . 15
4.3.1.1 Transmitter spectrum mask . 15
4.3.1.2 Maximum equivalent isotropically radiated power . 15
4.3.1.3 Transmitter frequency error . 16
4.3.1.4 Transmitter unwanted emissions . 16
4.3.2 Receiver requirements . 16
4.3.2.1 Receiver unwanted emissions in the spurious domain . 16
4.3.2.2 Sensitivity . 17
4.3.2.3 Receiver selectivity . 17
4.3.2.3.1 General . 17
4.3.2.3.2 Receiver spurious response rejection and adjacent channel rejection . 17
4.3.2.3.3 Receiver blocking . 18
4.3.2.3.4 Co-channel rejection . 18
4.3.3 Antennas . 18
5 Testing for compliance with technical requirements . 19
5.1 Environmental conditions for testing . 19
5.2 Interpretation of the measurement results . 19
5.3 Radio test suites . 20
5.3.1 Transmitter parameters . 20
5.3.1.1 Transmitter spectrum mask . 20
5.3.1.1.1 General . 20
5.3.1.1.2 Radiated measurements . 20
5.3.1.1.3 Conducted measurements . 22
5.3.1.2 Maximum equivalent isotropically radiated power . 23
5.3.1.2.1 General . 23
5.3.1.2.2 Radiated measurement . 24
5.3.1.2.3 Conducted measurement. 25
5.3.1.3 Transmitter frequency error . 25
5.3.1.3.1 General . 25
5.3.1.3.2 Radiated measurements . 26
5.3.1.3.3 Conducted measurements . 26
5.3.1.4 Transmitter unwanted emissions . 27
5.3.1.4.1 General . 27
ETSI
---------------------- Page: 5 ----------------------
oSIST prEN 300 674-2-2 V2.2.0:2019
4 Draft ETSI EN 300 674-2-2 V2.2.0 (2019-03)
5.3.1.4.2 Radiated measurement . 27
5.3.2 Receiver parameters . 28
5.3.2.1 Receiver unwanted emissions in the spurious domain . 28
5.3.2.1.1 General . 28
5.3.2.1.2 Radiated measurement . 28
5.3.2.2 Sensitivity . 29
5.3.2.2.1 General . 29
5.3.2.2.2 Radiated measurements . 29
5.3.2.2.3 Conducted measurements . 29
5.3.2.3 Receiver selectivity . 30
5.3.2.3.1 General . 30
5.3.2.3.2 Unwanted signal characteristics . 30
5.3.2.3.3 Measurement of receiver selectivity in OBU boresight . 30
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 32
Annex B (normative): Basics on testing . 33
B.1 General conditions . 33
B.1.1 Thermal balance . 33
B.1.2 Test signals . 33
B.1.3 Test sites . 34
B.1.3.1 Shielded anechoic chamber. 34
B.1.3.2 Open area test site . 35
B.1.3.3 Test fixture . 35
B.1.4 General requirements for RF cables . 36
B.1.5 Conducted measurements . 37
B.1.5.1 One antenna connector arrangement . 37
B.1.5.2 Two antenna connectors arrangement. 38
B.1.5.3 Test site requirements . 38
B.1.5.4 Site preparation for conducted measurements . 38
B.1.5.4.1 Monochromatic signals . 38
B.1.5.4.2 Modulated signals . 38
B.1.6 Radiated measurements . 39
B.1.6.1 One antenna arrangement . 39
B.1.6.2 Two antennas arrangement . 40
B.1.6.3 Test site requirements . 41
B.1.6.3.1 Measurement distances . 41
B.1.6.3.2 Free-space wave propagation . 41
B.1.6.4 Test and substitution antennas . 42
B.1.6.5 Site preparation for radiated OBU measurements . 42
B.1.6.5.1 Monochromatic signals . 42
B.1.6.5.2 Modulated signals . 44
B.1.6.5.3 Arrangement for OBU transmitter unwanted emissions measurement . 45
B.1.6.5.4 Arrangement for OBU receiver selectivity measurement . 47
B.2 Instruments . 49
B.2.1 Receiving device . 49
B.2.2 RF power sensor . 49
B.2.3 Combiner . 50
B.3 Power of modulated RSU carrier . 50
B.4 Bit error ratio measurements . 51
B.4.1 Basics . 51
B.4.2 BER measurement . 51
B.4.3 FER measurement . 51
B.4.3.1 Mathematical expressions . 51
B.4.3.2 Equipment . 52
B.4.3.3 Procedure . 52
Annex C (normative): Environmental profile . 53
ETSI
---------------------- Page: 6 ----------------------
oSIST prEN 300 674-2-2 V2.2.0:2019
5 Draft ETSI EN 300 674-2-2 V2.2.0 (2019-03)
C.1 General Requirements . 53
C.2 Mandatory environmental conditions . 53
C.3 Additional environmental conditions . 53
Annex D (informative): Maximum Measurement Uncertainty . 54
Annex E (informative): Bibliography . 55
Annex F (informative): Change History . 56
History . 57
ETSI
---------------------- Page: 7 ----------------------
oSIST prEN 300 674-2-2 V2.2.0:2019
6 Draft ETSI EN 300 674-2-2 V2.2.0 (2019-03)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.3] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.2].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive and associated
EFTA regulations.
The present document is part 2, sub-part 2 of a multi-part deliverable covering Transport and Traffic Telematics (TTT);
Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the
5 795 MHz to 5 815 MHz frequency band, as identified below:
Part 1: "General characteristics and test methods for Road Side Units (RSU) and On-Board Units (OBU)";
Part 2: "Harmonised Standard for access to radio spectrum";
Sub-part 1: "Road Side Units (RSU)";
Sub-part 2: "On-Board Units (OBU)".
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa
ETSI
---------------------- Page: 8 ----------------------
oSIST prEN 300 674-2-2 V2.2.0:2019
7 Draft ETSI EN 300 674-2-2 V2.2.0 (2019-03)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 9 ----------------------
oSIST prEN 300 674-2-2 V2.2.0:2019
8 Draft ETSI EN 300 674-2-2 V2.2.0 (2019-03)
1 Scope
The present document specifies technical characteristics and methods of measurements for Transport and Traffic
Telematics (TTT) systems:
• with a Radio Frequency (RF) output connection and specified antenna or with an integral antenna;
• for data transmission only;
• operating in the 5 795 MHz to 5 815 MHz frequency band.
The applicability of the present document covers only the On Board Units (OBU).
The present document complies with the Commission Implementing Decision 2017/1483/EU [i.4] and CEPT/ERC
Recommendation 70-03 [i.6].
The present document applies to the following radio equipment types operating in all or in part of the following service
frequency bands given in table 1.
Table 1: Frequency bands and centre frequencies f allocated for DSRC
Tx
Pan European Service Frequencies National Service Frequencies
Channel 1 5,795 GHz to 5,800 GHz, f = 5,7975 GHz
Tx
Channel 2 5,800 GHz to 5,805 GHz, f = 5,8025 GHz
Tx
Channel 3 5,805 GHz to 5,810 GHz, f = 5,8075 GHz
Tx
Channel 4 5,810 GHz to 5,815 GHz, f = 5,8125 GHz
Tx
NOTE: The relationship between the present document and essential requirements of article 3.2 of Directive
2014/53/EU [i.2] is given in annex A.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference/.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] CEN EN 12253 (2004): "Road transport and traffic telematics - Dedicated short-range
communication - Physical layer using microwave at 5,8 GHz".
[2] ISO 14906 (2018): "Electronic fee collection -- Application interface definition for dedicated
short-range communication".
[3] CEPT/ERC Recommendation 74-01E (2011): "Unwanted emissions in the spurious domain".
[4] CEN EN 13372 (2004): "Road Transport and Traffic Telematics (RTTT) - Dedicated short-range
communication - Profiles for RTTT applications".
ETSI
---------------------- Page: 10 ----------------------
oSIST prEN 300 674-2-2 V2.2.0:2019
9 Draft ETSI EN 300 674-2-2 V2.2.0 (2019-03)
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI TS 103 052 (V1.1.1) (03-2011): "Electromagnetic compatibility and Radi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.