SIST EN IEC 62868-1:2022
(Main)Organic light emitting diode (OLED) Light sources for general lighting - Safety - Part 1: General requirements and tests (IEC 62868-1:2020)
Organic light emitting diode (OLED) Light sources for general lighting - Safety - Part 1: General requirements and tests (IEC 62868-1:2020)
This part of IEC 62868 specifies general safety requirements of OLED products for use on DC
supplies up to 1000 V or AC supplies up to 1000 V at 50 Hz or 60 Hz for indoors and similar
general lighting purposes.
This document applies to any OLED light sources which are not covered by IEC 62868-2 (all
parts).
NOTE 1 Only test methods for DC operated OLED light sources are provided in this document. Provisions for AC
operated OLED products are under consideration.
NOTE 2 The construction of OLED tiles and panels is illustrated in Figure A.1 to Figure A.4 in Annex A.
NOTE 3 The OLED lighting system consisting of OLED panels or modules is illustrated in Annex D.
NOTE 4 This document applies to OLED light sources (tiles, panels, modules) which are composed of OLED
luminaires or OLED lamps, and it is intended so that the OLED light source in accordance with this document fits in
IEC 60598 (all parts) as a component of lighting equipment, in combination with other components.
NOTE 5 Where an appropriate Part 2 of IEC 62868 for an OLED light source does not exist, the nearest
applicable Part 2 of IEC 62868 can be used as a guide to the requirements and tests.
Organische Licht emittierende Dioden (OLED) Lichtquellen für die Allgemeinbeleuchtung - Sicherheit - Teil 1: Allgemeine Anforderungen und Prüfungen (IEC 62868-1:2020)
Sources lumineuses à diodes électroluminescentes organiques (OLED) destinées à l’éclairage général - Sécurité - Partie 1: Exigences générales et essais (IEC 62868-1:2020)
L'IEC 62868-1:2020 spécifie les exigences générales de sécurité des produits OLED destinés à être utilisés avec des alimentations en tension continue jusqu’à 1000 V ou avec des alimentations en tension alternative jusqu’à 1000 V à 50 Hz ou 60 Hz, pour l’éclairage général intérieur ou similaire.
Le présent document s’applique aux sources lumineuses OLED qui ne sont pas couvertes par l’IEC 62868-2 (toutes les parties).
Cette première édition annule et remplace l'IEC 62868 parue en 2014.
Organska svetleča dioda (OLED) Svetlobni viri za splošno razsvetljavo - Varnost - 1. del: Splošne zahteve in preskusi (IEC 62868-1:2020)
Ta del standarda IEC 62868 določa splošne varnostne zahteve za izdelke OLED za uporabo z enosmerno napajalno napetostjo do 1000 V ali izmenično napajalno napetostjo do 1000 V pri frekvenci 50 Hz ali 60 Hz za notranjo osvetlitev in podobne namene splošne razsvetljave. Ta dokument se uporablja za vse svetlobne vire OLED, ki niso zajeti v standardu IEC 62868-2 (vsi deli). OPOMBA 1: V tem dokumentu so podane le preskusne metode za svetlobne vire OLED za enosmerni tok. Ukrepi za izdelke OLED za izmenični tok so v obravnavi. OPOMBA 2: Sestava ploščic in plošč OLED je prikazana na slikah od A.1 do A.4 v dodatku A. OPOMBA 3: Svetlobni sistem OLED, sestavljen iz plošč ali modulov OLED, je prikazan na sliki v dodatku D. OPOMBA 4: Ta dokument se uporablja za svetlobne vire OLED (ploščice, plošče, module), ki so sestavljeni iz svetilk ali sijalk OLED; njegov namen je, da svetlobni vir OLED v skladu s tem dokumentom ustreza standardu IEC 60598 (vsi deli) kot sestavni del opreme za razsvetljavo, v kombinaciji z drugimi sestavnimi deli. OPOMBA 5: Če ustrezni 2. del standarda IEC 62868 za svetlobni vir OLED ne obstaja, je mogoče kot vodilo za zahteve in preskuse uporabiti najustreznejši 2. del standarda IEC 62868.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN IEC 62868-1:2022
01-januar-2022
Nadomešča:
SIST EN 62868:2016
Organska svetleča dioda (OLED) Svetlobni viri za splošno razsvetljavo - Varnost -
1. del: Splošne zahteve in preskusi (IEC 62868-1:2020)
Organic light emitting diode (OLED) Light sources for general lighting - Safety - Part 1:
General requirements and tests (IEC 62868-1:2020)
Organische Licht emittierende Dioden (OLED) Lichtquellen für die Allgemeinbeleuchtung
- Sicherheit - Teil 1: Allgemeine Anforderungen und Prüfungen (IEC 62868-1:2020)
Sources lumineuses à diodes électroluminescentes organiques (OLED) destinées à
l’éclairage général - Sécurité - Partie 1: Exigences générales et essais (IEC 62868-
1:2020)
Ta slovenski standard je istoveten z: EN IEC 62868-1:2021
ICS:
29.140.99 Drugi standardi v zvezi z Other standards related to
žarnicami lamps
SIST EN IEC 62868-1:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN IEC 62868-1:2022
---------------------- Page: 2 ----------------------
SIST EN IEC 62868-1:2022
EUROPEAN STANDARD EN IEC 62868-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2021
ICS 29.140.99 Supersedes EN 62868:2015 and all of its amendments
and corrigenda (if any)
English Version
Organic light emitting diode (OLED) Light sources for general
lighting - Safety - Part 1: General requirements and tests
(IEC 62868-1:2020)
Sources lumineuses à diodes électroluminescentes Organische Licht emittierende Dioden (OLED) Lichtquellen
organiques (OLED) destinées à l'éclairage général - für die Allgemeinbeleuchtung - Sicherheit - Teil 1:
Sécurité - Partie 1: Exigences générales et essais Allgemeine Anforderungen und Prüfungen
(IEC 62868-1:2020) (IEC 62868-1:2020)
This European Standard was approved by CENELEC on 2021-09-15. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 62868-1:2021 E
---------------------- Page: 3 ----------------------
SIST EN IEC 62868-1:2022
EN IEC 62868-1:2021 (E)
European foreword
The text of document 34A/2177/FDIS, future edition 1 of IEC 62868-1, prepared by SC 34A "Electric
light sources" of IEC/TC 34 "Lighting" was submitted to the IEC-CENELEC parallel vote and approved
by CENELEC as EN IEC 62868-1:2021.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022-05-05
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2024-11-05
document have to be withdrawn
This document supersedes EN 62868:2015 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a Standardization Request given to CENELEC by the
European Commission and the European Free Trade Association.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 62868-1:2020 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
1
IEC 60050 (series) NOTE Harmonized as EN IEC 63223 (series)
IEC 60598 (series) NOTE Harmonized as EN 60598 (series)
2
IEC 62868-2 (series) NOTE Harmonized as EN IEC 62868-2 (series)
1
To be published. Stage at the time of publication: prEN IEC 63223 (series).
2
To be published. Stage at the time of publication: FprEN IEC 62868-2 (series).
2
---------------------- Page: 4 ----------------------
SIST EN IEC 62868-1:2022
EN IEC 62868-1:2021 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod),
the relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60068-2-6 2007 Environmental testing - Part 2-6: Tests - EN 60068-2-6 2008
Test Fc: Vibration (sinusoidal)
IEC 60598-1 (mod) 2014 Luminaires - Part 1: General requirements EN 60598-1 2015
and tests
+ A1 2017 + A1 2018
IEC 62504 - General lighting - Light emitting diode (LED) EN 62504 -
products and related equipment - Terms
and definitions
IEC TR 62854 2014 Sharp edge testing apparatus and test - -
procedure for lighting equipment - Tests for
sharpness of edge
IEC TS 62972 - General lighting - Organic light emitting - -
diode (OLED) products and related
equipment - Terms and definitions
ISO 4046-4 2016 Paper, board, pulps and related terms - - -
Vocabulary - Part 4: Paper and board
grades and converted products
3
---------------------- Page: 5 ----------------------
SIST EN IEC 62868-1:2022
---------------------- Page: 6 ----------------------
SIST EN IEC 62868-1:2022
IEC 62868-1
®
Edition 1.0 2020-05
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
colour
inside
Organic light emitting diode (OLED) light sources for general lighting – Safety –
Part 1: General requirements and tests
Sources lumineuses à diodes électroluminescentes organiques (OLED)
destinées à l’éclairage général – Sécurité –
Partie 1: Exigences générales et essais
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.140.99 ISBN 978-2-8322-8309-7
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN IEC 62868-1:2022
– 2 – IEC 62868-1:2020 © IEC 2020
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 8
4 General . 9
4.1 General requirements . 9
4.2 General test requirements . 9
5 Marking . 10
5.1 Contents and location . 10
5.2 Durability and legibility of marking . 10
6 Construction . 11
6.1 General . 11
6.2 Mechanical strength . 11
6.3 Internal short circuit . 11
6.4 Wireways . 12
6.5 Resistance to dust, solid objects and moisture . 12
7 Mechanical hazard . 12
8 Fault conditions . 12
9 Insulation resistance and electric strength . 13
9.1 Insulation resistance . 13
9.2 Electric strength . 13
10 Thermal stress . 13
11 Creepage distances and clearances . 13
12 Resistance to heat and fire . 13
12.1 Resistance to heat . 13
12.2 Resistance to fire . 14
13 Photobiological safety . 14
14 Terminals . 14
15 Information for luminaire design . 14
Annex A (informative) Construction of OLED panels . 15
Annex B (informative) Information for luminaire design . 17
Annex C (normative) Method of provoking an internal short circuit . 18
C.1 Method for an OLED panel with glass substrates . 18
C.2 Method for an OLED panel with flexible plastic substrates . 18
Annex D (informative) Overview of the OLED lighting system consisting of OLED
panel or module . 19
Annex E (informative) Classification of OLED modules . 20
E.1 Power supply classification . 20
E.2 Installation method classification . 20
Bibliography . 21
---------------------- Page: 8 ----------------------
SIST EN IEC 62868-1:2022
IEC 62868-1:2020 © IEC 2020 – 3 –
Figure A.1 – Schematic diagram of OLED tile for lighting . 15
Figure A.2 – Schematic diagram of OLED panel (Example 1) for lighting . 15
Figure A.3 – Schematic diagram of OLED panel (Example 2) for lighting . 16
Figure A.4 – Schematic diagram of OLED panel (Example 3) for lighting . 16
Figure D.1 – Schematic diagram of OLED lighting system consisting of OLED panel or
module . 19
Table 1 – Contents and location of marking . 10
---------------------- Page: 9 ----------------------
SIST EN IEC 62868-1:2022
– 4 – IEC 62868-1:2020 © IEC 2020
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
ORGANIC LIGHT EMITTING DIODE (OLED) LIGHT
SOURCES FOR GENERAL LIGHTING – SAFETY –
Part 1: General requirements and tests
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62868-1 has been prepared by subcommittee 34A: Lamps, of IEC
technical committee 34: Lamps and related equipment.
This first edition cancels and replaces IEC 62868 published in 2014.
The text of this International Standard is based on the following documents:
FDIS Report on voting
34A/2177/FDIS 34A/2185/RVD
Full information on the voting for the approval of this International Standard can be found in
the report on voting indicated in the above table.
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
---------------------- Page: 10 ----------------------
SIST EN IEC 62868-1:2022
IEC 62868-1:2020 © IEC 2020 – 5 –
A list of all parts in the IEC 62868 series, published under the general title Organic light
emitting diode (OLED) light sources for general lighting – Safety, can be found on the IEC
website.
In this document, the following print types are used:
– requirements: roman type,
– test specifications: italic type,
– notes: smaller roman type.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data related
to the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.
---------------------- Page: 11 ----------------------
SIST EN IEC 62868-1:2022
– 6 – IEC 62868-1:2020 © IEC 2020
INTRODUCTION
This part of IEC 62868 provides a set of general safety requirements and tests of OLED light
sources which are applicable to general indoor lightings. This document specifies the
requirements and tests for simple OLED light sources which do not include active electronic
components and consist of rigid substrates. It applies to the common requirements and tests
to verify the safety of all types of OLED light sources such as OLED modules and flexible
OLED panels. This document applies to OLED panels and tiles which consist of rigid
substrates. It also applies to any OLED light sources which are not specified in IEC 62868-2
1
(all parts) .
The parts which make up the IEC 62868-2 series, in referring to any clauses of this document,
specify the extent of application of this document; they also include additional requirements
and tests as necessary.
Where the requirements of any clauses of this document are referred to in the various parts
that make up the IEC 62868-2 series by the phrase "The requirements of Clause n of
IEC 62868-1 apply", this phrase will be interpreted as meaning that all requirements of the
clauses in question of this document apply, except any which are clearly inapplicable to a
particular type of OLED light source covered by the Part n of the IEC 62868-2 series
concerned.
The safety requirements of this document are intended to ensure that electrical lightings
constructed in accordance with this document do not endanger the safety of users or
properties when the light sources are properly installed, maintained and used in applications.
Particular requirements and tests for OLED light sources which include any active electronic
components and consist of flexible substrate will be the subject of a separate standard, as the
need arises.
___________
1
Under preparation. Stage at the time of publication IEC AFDIS 62868-2-1:2020, IEC AFDIS 62868-2-2:2020 and
IEC ACDV 62868-2-3:2020.
---------------------- Page: 12 ----------------------
SIST EN IEC 62868-1:2022
IEC 62868-1:2020 © IEC 2020 – 7 –
ORGANIC LIGHT EMITTING DIODE (OLED) LIGHT
SOURCES FOR GENERAL LIGHTING – SAFETY –
Part 1: General requirements and tests
1 Scope
This part of IEC 62868 specifies general safety requirements of OLED products for use on DC
supplies up to 1000 V or AC supplies up to 1000 V at 50 Hz or 60 Hz for indoors and similar
general lighting purposes.
This document applies to any OLED light sources which are not covered by IEC 62868-2 (all
parts).
NOTE 1 Only test methods for DC operated OLED light sources are provided in this document. Provisions for AC
operated OLED products are under consideration.
NOTE 2 The construction of OLED tiles and panels is illustrated in Figure A.1 to Figure A.4 in Annex A.
NOTE 3 The OLED lighting system consisting of OLED panels or modules is illustrated in Annex D.
NOTE 4 This document applies to OLED light sources (tiles, panels, modules) which are composed of OLED
luminaires or OLED lamps, and it is intended so that the OLED light source in accordance with this document fits in
IEC 60598 (all parts) as a component of lighting equipment, in combination with other components.
NOTE 5 Where an appropriate Part 2 of IEC 62868 for an OLED light source does not exist, the nearest
applicable Part 2 of IEC 62868 can be used as a guide to the requirements and tests.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition
cited applies. For undated references, the latest edition of the referenced document (including
any amendments) applies.
IEC 60598-1:2014, Luminaires – Part 1: General requirements and tests
IEC 60598-1:2014/AMD1:2017
IEC 60068-2-6:2007, Environmental testing – Part 2-6: Tests – Test Fc: Vibration (sinusoidal)
IEC 62504, General lighting – Light emitting diode (LED) products and related equipment –
Terms and definitions
IEC TR 62854:2014, Sharp edge testing apparatus and test procedure for lighting equipment –
Tests for sharpness of edge
IEC TS 62972, General lighting – Organic light emitting diode (OLED) products and related
equipment – Terms and definitions
ISO 4046-4:2016, Paper, board, pulps and related terms – Vocabulary – Part 4: Paper and
board grades and converted products
---------------------- Page: 13 ----------------------
SIST EN IEC 62868-1:2022
– 8 – IEC 62868-1:2020 © IEC 2020
3 Terms and definitions
For the purpose of this document, the terms and definitions given in IEC 62504 and
IEC TS 62972 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following
addresses:
• IEC Electropedia: available at http://www.electropedia.org/
• ISO Online browsing platform: available at http://www.iso.org/obp
3.1
organic light emitting diode
OLED
light emitting semiconductor consisting of an electroluminescent zone made of organic
compounds, situated between two electrodes
Note 1 to entry: This note applies to the French language only.
3.2
OLED tile
smallest functional OLED light source which cannot be separated into smaller OLED lighting
elements containing at least one contact ledge with at least one positive and one negative
pole for connection to the electrical power supply
3.3
OLED panel
independently operable unit OLED product containing an OLED tile and means of connection
to the electrical supply
Note 1 to entry: An OLED panel may have a connector, PCB (printed circuit board), passive electronic
components and optionally a frame.
3.4
OLED module
assembly of one or more OLED panels and active electronic components
Note 1 to entry: The classification of OLED modules is given in Annex E.
3.5
semi-integrated OLED module
OLEDsi module
OLED module which carries the control unit of the controlgear, and is operated by the
separated power supply of the controlgear
3.6
integrated OLED module
OLEDi module
OLED module incorporating controlgear and any additional elements necessary for stable
operation of the light source, designed for direct connection to the supply voltage
3.7
integral OLED module
OLED module, designed to form a non-replaceable part of a luminaire
3.8
built-in OLED module
OLED module, designed to form a replaceable part to be built into a luminaire, a box, an
enclosure or the like and not intended to be mounted outside a luminaire
---------------------- Page: 14 ----------------------
SIST EN IEC 62868-1:2022
IEC 62868-1:2020 © IEC 2020 – 9 –
3.9
independent OLED module
OLED module, designed for being mounted or placed separately from a luminaire, from an
additional box or enclosure or the like
Note 1 to entry: The independent OLED module provides all the necessary protection with regard to safety
according to its classification and marking.
Note 2 to entry: An example of an independent OLED module is a system where the OLED module is connected
via a glass fibre with the luminaire head.
3.10
rated value
quantity value for a characteristic of a product for specific operating conditions with the values
and the conditions specified in the relevant standard, or assigned by the manufacturer or
responsible vendor
3.11
type test
test or series of tests made on a type test sample for the purpose of checking compliance of
the design of a given product with the requirements of the relevant standard
3.12
stabilization
keeping of an OLED product switched on under specified electrical input
to obtain stable operation
Note 1 to entry: The mentioned operation can be photometric or electrical under specified conditions in the
relevant test clause.
3.13
dark spot
small area remarkably darker than the surrounding light output area on the OLED product
Note 1 to entry: A dark spot can be due to lower current density or an open circuit in that area.
3.14
internal short circuit
unintentional conductive path between the OLED anode and OLED cathode localized on a
small area
Note 1 to entry: An internal short circuit can look like a dark spot. It can lead to a significant heat generation in
that area.
4 General
4.1 General requirements
An OLED product shall be designed and manufactured in such a way as to operate safely
during its intended use and not to cause any danger to persons and the environment.
In case of a failure of an OLED product it shall fail safely.
Reference to an OLED product also includes reference to OLED tiles in the requirements and
tests of this document.
4.2 General test requirements
The tests, unless otherwise specified, are carried out at an ambient temperature of 25 °C ±
5 °C.
---------------------- Page: 15 ----------------------
SIST EN IEC 62868-1:2022
– 10 – IEC 62868-1:2020 © IEC 2020
The tests shall be conducted at the rated current with a tolerance of 1 % unless otherwise
specified in this document.
The OLED product under test shall be mounted in accordance with the manufacturer’s
installation instructions. If more than one way of mounting is specified, the most onerous way
shall be chosen for each test. For electrical tests, this is the position leading to the largest
heat build-up of the light emitting surface. The orientation of the OLED product shall be
maintained during the entire test.
5 Marking
5.1 Contents and location
Marking of the OLED product shall be done in accordance with Table 1.
Table 1 – Contents and location of marking
Packaging or product
Parameters Product
datasheet or leaflet
Manufacturer (or responsible vendor) or Mandatory Mandatory
trademark
Polarity (in case of DC power supply) Mandatory
Neutral or earthing terminal Mandatory
Model number or production code Mandatory Mandatory
Rated current or rated current range Mandatory
Rated voltage or rated voltage range Mandatory
Rated power Mandatory
Type of power supply (DC or AC) and frequency Mandatory
Shape and dimension Mandatory
Connecting information Mandatory
Mounting instruction Mandatory
Operating temperature range Mandatory
IP number Mandatory
Information for luminaire design Mandatory
The connecting information shall include methods of mechanical and electrical connection.
The information of the electrical connection may include the type of driver.
For marking of the IP numb
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.