SIST EN 61788-18:2014

Superconductivity - Part 18: Mechanical properties measurement - Room temperature tensile test of Ag- and/or Ag alloy-sheathed Bi-2223 and Bi-2212 composite superconductors

This International Standard specifies a test method detailing the tensile test procedures to be carried out on Ag/Bi-2223 and Ag/Bi-2212 superconductive composite wires at room temperature. This test is used to measure the modulus of elasticity and to determine the 0,2 % proof strength. When the 0,2 % proof strength could not be determined due to earlier failure, the stress level at apparent strains of 0,05 %, 0,1 %, 0,15 %, 0,2 %, 0,25 % with increment of 0,05 % is measured. The values for elastic limit, fracture strength, percentage elongation after fracture and the fitted type of 0,2 % proof strength serve only as a reference (see Clauses A.4, A.5, A.6 and A.10). The sample covered by this test procedure should have a round or rectangular cross-section with an area of 0,3 mm2 to 2,0 mm2 (corresponding to the tape-shaped wires with width of 2,0 mm to 5,0 mm and thickness of 0,16 mm to 0,4 mm).

Supraleitfähigkeit - Teil 18: Messung der mechanischen Eigenschaften - Zugversuch von Ag und/oder Ag-Legierung ummantelten Bi-2223 und Bi-2212 Verbundsupraleitern bei Raumtemperatur

Supraconductivité - Partie 18: Mesure des propriétés mécaniques - Essai de traction à température ambiante des supraconducteurs composites Bi-2223 et Bi-2212 avec gaine Ag et/ou en alliage d'Ag

La CEI 61788-18:2013 spécifie une méthode d'essai détaillant les modes opératoires d'essai de traction à exécuter sur des fils composites supraconducteurs d'Ag/Bi-2223 et d'Ag/Bi-2212 à température ambiante. Cet essai est utilisé pour mesurer le module d'élasticité et pour déterminer la charge d'épreuve à 0,2 %. Lorsqu'on ne peut pas déterminer la charge d'épreuve à 0,2 % en raison d'une défaillance antérieure, on mesure le niveau de contrainte pour des déformations apparentes de 0,05 %, 0,1 %, 0,15 %, 0,2 %, 0,25 % avec un incrément de 0,05 %. Les valeurs de la limite élastique, de la résistance à la rupture, du pourcentage d'allongement après fracture et du type ajusté de charge d'épreuve à 0,2 % ne servent que de référence. Il convient que l'échantillon couvert par ce mode opératoire d'essai ait une section circulaire ou rectangulaire d'une surface de 0,3 mm² à 2,0 mm² (correspondant aux fils en forme de bande d'une largeur de 2,0 mm à 5,0 mm et d'une épaisseur de 0,16 mm à 0,4 mm). Mots clé: supraconductivité, propriétés mécaniques

Superprevodnost - 18. del: Merjenje mehanskih lastnosti - Natezni preskus Ag- in/ali z Ag zlitino oplaščenih Bi-2223 in Bi-2212 kompozitnih superprevodnikov pri sobni temperaturi (IEC 61788-18:2013)

General Information

• Status: Published
• Publication Date: 10-Feb-2014
• ICS: 29.050 - Superconductivity and conducting materials
• Technical Committee: I09 - Imaginarni 09
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 13-Jan-2014
• Due Date: 20-Mar-2014
• Completion Date: 11-Feb-2014
• Ref Project: EN 61788-18:2013 - Superconductivity - Part 18: Mechanical properties measurement - Room temperature tensile test of Ag- and/or Ag alloy-sheathed Bi-2223 and Bi-2212 composite superconductors

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61788-18:2014
01-marec-2014
6XSHUSUHYRGQRVWGHO0HUMHQMHPHKDQVNLKODVWQRVWL1DWH]QLSUHVNXV$J
LQDOL]$J]OLWLQRRSODãþHQLK%LLQ%LNRPSR]LWQLKVXSHUSUHYRGQLNRYSUL
VREQLWHPSHUDWXUL,(&
Superconductivity - Part 18: Mechanical properties measurement - Room temperature
tensile test of Ag- and/or Ag alloy-sheathed Bi-2223 and Bi-2212 composite
superconductors
Supraconductivité - Partie 18: Mesure des propriétés mécaniques - Essai de traction à
température ambiante des supraconducteurs composites Bi-2223 et Bi-2212 avec gaine
Ag et/ou en alliage d'Ag
Ta slovenski standard je istoveten z: EN 61788-18:2013
ICS:
29.050 Superprevodnost in prevodni Superconductivity and
materiali conducting materials
SIST EN 61788-18:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61788-18:2014

---------------------- Page: 2 ----------------------

SIST EN 61788-18:2014


EUROPEAN STANDARD
EN 61788-18

NORME EUROPÉENNE
December 2013
EUROPÄISCHE NORM

ICS 29.050



English version


Superconductivity -
Part 18: Mechanical properties measurement -
Room temperature tensile test of Ag- and/or Ag alloy-sheathed Bi-2223
and Bi-2212 composite superconductors
(IEC 61788-18:2013)


Supraconductivité -  Supraleitfähigkeit -
Partie 18: Mesure des propriétés mécaniques - Teil 18: Messung der mechanischen
Essai de traction à température ambiante des Eigenschaften -
supraconducteurs composites Bi-2223 et Zugversuch von Ag und/oder Ag-Legierung
Bi-2212 avec gaine Ag et/ou en alliage d'Ag ummantelten Bi-2223 und Bi-2212
(CEI 61788-18:2013) Verbundsupraleitern bei Raumtemperatur
(IEC 61788-18:2013)





This European Standard was approved by CENELEC on 2013-10-17. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

CEN-CENELEC Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61788-18:2013 E

---------------------- Page: 3 ----------------------

SIST EN 61788-18:2014
EN 61788-18:2013 - 2 -
Foreword
The text of document 90/326/FDIS, future edition 1 of IEC 61788-18, prepared by IEC/TC 90
"Superconductivity" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN 61788-18:2013.
The following dates are fixed:
– latest date by which the document has to be implemented at (dop) 2014-07-17
national level by publication of an identical national
standard or by endorsement
– latest date by which the national standards conflicting with (dow) 2016-10-17
the document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 61788-18:2013 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 61788-6 NOTE Harmonized as EN 61788-6.
ISO 3611:2010 NOTE Harmonized as EN ISO 3611:2010 (not modified).

---------------------- Page: 4 ----------------------

SIST EN 61788-18:2014
- 3 - EN 61788-18:2013
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE  When an international publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.

Publication Year Title EN/HD Year
IEC 60050 series International Electrotechnical Vocabulary - -
ISO 376 - Metallic materials - Calibration of force- EN ISO 376 -
proving instruments used for the
verification of uniaxial testing machines
ISO 6892-1 - Metallic materials - Tensile testing EN ISO 6892-1 -
Part 1: Method of test at room temperature
ISO 7500-1 - Metallic materials - Verification of static EN ISO 7500-1 -
uniaxial testing machines
Part 1: Tension/compression testing
machines - Verification and calibration of
the force-measuring system
ISO 9513 - Metallic materials - Calibration of EN ISO 9513 -
extensometer systems used in uniaxial
testing

---------------------- Page: 5 ----------------------

SIST EN 61788-18:2014

---------------------- Page: 6 ----------------------

SIST EN 61788-18:2014



IEC 61788-18

®


Edition 1.0 2013-09




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Superconductivity –

Part 18: Mechanical properties measurement – Room temperature tensile test of

Ag- and/or Ag alloy-sheathed Bi-2223 and Bi-2212 composite superconductors




Supraconductivité –

Partie 18: Mesure des propriétés mécaniques – Essai de traction à température


ambiante des supraconducteurs composites Bi-2223 et Bi-2212 avec gaine Ag

et/ou en alliage d'Ag












INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX W


ICS 29.050 ISBN 978-2-8322-1051-2



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 61788-18:2014
– 2 – 61788-18 © IEC:2013
CONTENTS
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 7
4 Principle . 9
5 Apparatus . 9
5.1 General . 9
5.2 Testing machine . 9
5.3 Extensometer . 9
6 Specimen preparation . 9
6.1 General . 9
6.2 Length of specimen . 10
6.3 Removing insulation . 10
6.4 Determination of cross-sectional area (S ) . 10
0
7 Testing conditions . 10
7.1 Specimen gripping . 10
7.2 Setting of extensometer . 10
7.3 Testing speed . 10
7.4 Test . 10
8 Calculation of results . 12
8.1 Modulus of elasticity (E) . 12
8.2 0,2 % proof strength (R ) . 13
p 0,2
8.3 Tensile stress at specified strains (R ) . 13
A
8.4 Fracture strength (R ) . 14
f
9 Uncertainty of measurement . 14
10 Test report . 14
10.1 Specimen . 14
10.2 Results . 15
10.3 Test conditions . 15
Annex A (informative) Additional information relating to Clauses 1 to 14 . 16
Annex B (informative) Uncertainty considerations . 26
Annex C (informative) Specific examples related to evaluation of uncertainties for
Ag/Bi-2223 and Ag/Bi-2212 wires . 30

Figure 1 – Typical stress-strain curve and definition of modulus of elasticity and 0,2 %
proof strengths of an externally laminated Ag/Bi-2223 wire by brass foil . 11
Figure 2 – Typical stress-strain curve of an Ag/Bi-2223 wire where the 0,2 % proof
strengths could not be determined and definition of tensile stresses at specified strains . 12
Figure A.1 – Low mass Siam twin type extensometer with a gauge length of ~ 12,3 mm
(total mass ~ 0,5 g) . 16
Figure A.2 – Low mass double extensometer with a gauge length of ~ 25,6 mm (total
mass ~ 3 g) . 17
Figure A.3 – An example of the extensometer provided with balance weight and vertical
specimen axis . 18
Figure A.4 – Original raw data of an Ag/Bi-2223 wire measurement in form of load and
displacement graph . 19

---------------------- Page: 8 ----------------------

SIST EN 61788-18:2014
61788-18 © IEC:2013 – 3 –
Figure A.5 – Typical stress versus strain of an Ag/Bi-2223 wire up to the elastic limit
corresponding to the transition region from elastic to plastic deformation (point G) . 20
Figure C.1 – Measured stress versus strain curve for Bi-2223 wire . 31

Table A.1 – Results of relative standard uncertainty values achieved on different
Ag/Bi-2223 wires during the international round robin tests . 23
Table A.2 – Selected data for F test for E of Sample E bare wire . 24
0
Table A.3 – Results of F-test for the variations of E of four kinds of Bi-2223 wires . 24
0
Table B.1 – Output signals from two nominally identical extensometers . 27
Table B.2 – Mean values of two output signals . 27
Table B.3 – Experimental standard deviations of two output signals . 27
Table B.4 – Standard uncertainties of two output signals . 27
Table B.5 – Coefficient of variations of two output signals . 28
Table C.1. – Load cell specifications according to manufacturer’s data sheet. 32
Table C.2 – Uncertainties from various factors for stress measurement . 33
Table C.3 – Uncertainties with respect to measurement of strain measurement . 35
Table C.4 – Summary of evaluated uncertainties caused by various factors . 35
Table C.5 – Results of uncertainty evaluation for the modulus of elasticity (E = 86,1
0
GPa) as a function of initial cross head rate . 36
Table C.6 – Uncertainties from various factors for stress measurement . 37
Table C.7 – Results of uncertainty evaluation for the stress (R = 42,5 MPa) as a function
of initial strain rate . 37

---------------------- Page: 9 ----------------------

SIST EN 61788-18:2014
– 4 – 61788-18 © IEC:2013
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

SUPERCONDUCTIVITY –

Part 18: Mechanical properties measurement –
Room temperature tensile test of Ag- and/or Ag alloy-sheathed
Bi-2223 and Bi-2212 composite superconductors


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in
addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses
arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61788-18 has been prepared by IEC technical committee 90:
Superconductivity.
The text of this standard is based on the following documents:
FDIS Report on voting
90/326/FDIS 90/327/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
A list of all parts of the IEC 61788 series, published under the general title Superconductivity,
can be found on the IEC website.

---------------------- Page: 10 ----------------------

SIST EN 61788-18:2014
61788-18 © IEC:2013 – 5 –
The committee has decided that the contents of this publication will remain unchanged until the
stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to
the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.

---------------------- Page: 11 ----------------------

SIST EN 61788-18:2014
– 6 – 61788-18 © IEC:2013
INTRODUCTION
Several types of composite superconductors have now been commercialised. Especially, high
temperature superconductors such as Ag- and/or Ag alloy-sheathed Bi-2223 (Ag/Bi-2223) and
Ag- and/or Ag alloy-sheathed Bi-2212 (Ag/Bi-2212) wires are now manufactured in industrial
scale. Commercial composite superconductors have a high current density and a small
cross-sectional area. The major applications of composite superconductors are to build
electrical power devices and superconducting magnets. While the magnet is being
manufactured, complicated stresses/strains are applied to its windings and, while it is being
energized, a large electromagnetic force is applied to the superconducting wires because of its
high current density. It is therefore indispensable to determine the mechanical properties of the
superconductive wires from which the windings are made.
The Ag/Bi-2223 and Ag/Bi-2212 superconductive composite wires fabricated by the powder-in
-tube method are composed of a number of oxide filaments with silver and silver alloy as a
stabilizer and supporter. In the case that the external reinforcement of Ag/Bi-2223 and
Ag/Bi-2212 wires by using thin stainless or Cu alloy foils has been adopted in order to resist the
large electromagnet force, this standard shall be also applied.

---------------------- Page: 12 ----------------------

SIST EN 61788-18:2014
61788-18 © IEC:2013 – 7 –
SUPERCONDUCTIVITY –

Part 18: Mechanical properties measurement –
Room temperature tensile test of Ag- and/or Ag alloy-sheathed
Bi-2223 and Bi-2212 composite superconductors



1 Scope
This International Standard specifies a test method detailing the tensile test procedures to be
carried out on Ag/Bi-2223 and Ag/Bi-2212 superconductive composite wires at room
temperature.
This test is used to measure the modulus of elasticity and to determine the 0,2 % proof strength.
When the 0,2 % proof strength could not be determined due to earlier failure, the stress level at
apparent strains of 0,05 %, 0,1 %, 0,15 %, 0,2 %, 0,25 % with increment of 0,05 % is measured.
The values for elastic limit, fracture strength, percentage elongation after fracture and the fitted
type of 0,2 % proof strength serve only as a reference (see Clauses A.4, A.5, A.6 and A.10).
The sample covered by this test procedure should have a round or rectangular cross-section
2 2
with an area of 0,3 mm to 2,0 mm (corresponding to the tape-shaped wires with width of 2,0
mm to 5,0 mm and thickness of 0,16 mm to 0,4 mm).
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and
are indispensable for its application. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
IEC 60050 (all parts), International Electrotechnical Vocabulary (available at
)
ISO 376, Metallic materials – Calibration of force-proving instruments used for the verification of
uniaxial testing machines
ISO 6892-1, Metallic materials – Tensile testing – Part 1: Method of test at room temperature
ISO 7500-1, Metallic materials – Verification of static uniaxial testing machines – Part 1:
Tension/compression testing machines – Verification and calibration of the force-measuring
system
ISO 9513, Metallic materials – Calibration of extensometer systems used in uniaxial testing
3 Terms and definitions
For the purposes of this document, terms and definitions given in IEC 60050-815 and
ISO 6892-1, as well as the following terms and definitions apply.

---------------------- Page: 13 ----------------------

SIST EN 61788-18:2014
– 8 – 61788-18 © IEC:2013
3.1
tensile stress
R
tensile force divided by the original cross-sectional area at any moment during the test
3.2
tensile strain
A
displacement increment divided by initial gauge length of extensometers at any moment during
the test
3.3
extensometer gauge length
L
G
length of the parallel portion of the test piece used for the measurement of displacement by
means of an extensometer
3.4
distance between grips
L
o
length between grips that hold a test specimen in position before the test is started
3.5
modulus of elasticity
E
gradient of the straight portion of the stress-strain curve in the elastic deformation region
SEE: Figure 1.
Note 1 to entry: It can be determined differently depending upon the adopted procedures:
a) one from the initial loading curve by zero offset line expressed as E ,
0
b) the other one given by the slope of line during the elastic unloading, expressed as E .
U
3.6
0,2 % proof strength
R
p0,2
stress value when the superconductive composite wire yields by 0,2 %
SEE: Figure 1.
Note 1 to entry: The designated stress, R or R corresponds to point A or B obtained from the initial loading
p0,2-0 p0,2-U
or unloading curves in Figure 1, respectively. This strength is regarded as a representative 0,2 % proof strength of the
composite.
3.7
tensile stress at specified strains
R
A
tensile stress corresponding to different specified strain (A)
3.8
fracture strength
R
f
tensile stress at the fracture
Note 1 to entry: In most cases, the fracture strength is defined as tensile stress corresponding to the maximum
testing force

---------------------- Page: 14 ----------------------

SIST EN 61788-18:2014
61788-18 © IEC:2013 – 9 –
3.9
tensile stress at elastic limit
R
el
tensile stress at elastic limit corresponding to transition instant from elastic to plastic
deformation
3.10
tensile strain at elastic limit
A
el
strain at elastic limit
Note 1 to entry: The stress R and the corresponding strain A refer to point G in Figure A.5, respectively and are
el el
regarded as the transition point from elastic to plastic deformation.
4 Principle
The test consists of straining a test piece by a tensile force, generally to fracture, in principle for
the purpose of determining the mechanical properties defined in Clause 3.
Depending on the employed strain measuring method, however, the quantities determined by
the present test should be limited. When using the conventional single extensometer system, the
determination of E and R is recommended. On the other hand, all quantities described
U p0,2-U
here can be determined by using double extensometer system, because of its capability to
compensate the bending effects of the specimen thereby guaranteeing a proper determination
of the modulus of elasticity.
5 Apparatus
5.1 General
The test machine and the extensometers shall conform to ISO 7500-1 and ISO 9513,
respectively. The calibration shall obey ISO 376. The special requirements of this standard are
presented here.
5.2 Testing machine
A tensile machine control system that provides a constant crosshead speed shall be used. Grips
shall have a structure and strength appropriate for the test specimen and shall be constructed to
provide a firm connection with the tensile machine. The faces of the grips shall be filed or
knurled, or otherwise roughened, so that the test specimen will not slip during the test. Gripping
may be a screw type, or pneumatically or hydraulically actuated.
5.3 Extensometer
The mass of the extensometer shall be 30 g or less, so as not to affect the mechanical properties
of superconductive composite wires. The mass of the extensometers shall be balanced
symmetrically around the wire to avoid any non-alignment force. Care shall be taken to prevent
bending moments from being applied to the test specimen (see Clauses A.2 and A.3).
6 Specimen preparation
6.1 General
When a test specimen sampled from a bobbin needs to be straightened, a method that affects
the material as little as possible shall be used. Care shall be taken to prevent bending or
pre-loading when the specimen is handled manually.

---------------------- Page: 15 ----------------------

SIST EN 61788-18:2014
– 10 – 61788-18 © IEC:2013
6.2 Length of specimen
The length of the test specimen shall be the sum of the inward distance between grips and both
grip lengths. The inward distance between the grips shall be 60 mm or more, as requested for
the installation of the extensometer.
6.3 Removing insulation
If the test specimen surface is coated with an insulating material, the coatings shall be removed.
Either a chemical or mechanical method shall be used with care taken in removing the coating so
as not to damage the specimen surface (see Clause A.7).
6.4 Determination of cross-sectional area (S )
0
A micrometer or other dimension-measuring apparatus shall be used to obtain the
cross-sectional area of the specimen after the insulation coating has been removed. The
cross-sectional area of tape-shaped wires shall be obtained from the product of its thickness and
width. Corrections to be made for the corners of the cross-sectional area shall be determined
through consultation among the parties concerned (see Clause A.8). In addition, in the cases of
lens-shaped wires, measurement of width and thickness by photograph may also be done. Mean
value of middle and edge thickness shall be used for wires with varying thickness along its width
to minimize mismatch effect on its cross-sectional area. The cross-sectional area of a round wire
shall be calculated using the arithmetic mean of the two orthogonal diameters.
7 Testing conditions
7.1 Specimen gripping
When the test specimen is going to be mounted on the grips of the tensile machine, the test
specimen and tensile loading axis shall be aligned to be in a straight line. Sand paper may be
inserted as a cushioning material to prevent the gripped surfaces of the specimen from slipping
and fracturing (see Clause A.9). During mounting of the sample, bending or deformation shall be
prevented.
7.2 Setting of extensometer
When mounting the extensometer, care shall be taken to prevent the test specimen from being
deformed like in the case of indentation due to extensometers’ sharp edges which might cause
an earlier fracture of the specimen. The extensometer shall be mounted at the centre between
the grips, aligning the measureme
...