SIST EN ISO 16946:2017
(Main)Non-destructive testing - Ultrasonic testing - Specification for step wedge calibration block (ISO 16946:2017)
Non-destructive testing - Ultrasonic testing - Specification for step wedge calibration block (ISO 16946:2017)
This document specifies the dimensions, material, and manufacture of a step wedge steel block for the
calibration of ultrasonic instruments.
Zerstörungsfreie Prüfung - Ultraschallprüfung - Beschreibung des Stufenkeil-Kalibrierkörpers (ISO 16946:2017)
Dieses Dokument legt die Maße, den Werkstoff und die Herstellung eines Stufenkeil-Kalibrierkörpers zur Justierung von Ultraschallprüfgeräten fest.
Essais non destructifs - Essais par ultrasons - Spécifications relatives aux blocs d'étalonnage à gradins (ISO 16946:2017)
ISO 16946:2017 spécifie les dimensions, le matériau constitutif et la fabrication des blocs à gradins en acier pour l'étalonnage des appareils de contrôle par ultrasons.
Neporušitvene preiskave - Ultrazvočno preskušanje - Specifikacija za kalibracijo stopničastega klinastega bloka (ISO 16946:2017)
Ta dokument določa mere, material in proizvodnjo stopničastih klinastih jeklenih blokov za kalibracijo ultrazvočne opreme.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 16946:2017
01-julij-2017
1DGRPHãþD
SIST EN ISO 16946:2015
1HSRUXãLWYHQHSUHLVNDYH8OWUD]YRþQRSUHVNXãDQMH6SHFLILNDFLMD]DNDOLEUDFLMR
VWRSQLþDVWHJDNOLQDVWHJDEORND ,62
Non-destructive testing - Ultrasonic testing - Specification for step wedge calibration
block (ISO 16946:2017)
Zerstörungsfreie Prüfung - Ultraschallprüfung - Beschreibung des Stufenkeil-
Kalibrierkörpers (ISO 16946:2017)
Essais non destructifs - Essais par ultrasons - Spécifications relatives aux blocs
d'étalonnage à gradins (ISO 16946:2017)
Ta slovenski standard je istoveten z: EN ISO 16946:2017
ICS:
19.100 Neporušitveno preskušanje Non-destructive testing
SIST EN ISO 16946:2017 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 16946:2017
---------------------- Page: 2 ----------------------
SIST EN ISO 16946:2017
EN ISO 16946
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2017
EUROPÄISCHE NORM
ICS 19.100 Supersedes EN ISO 16946:2015
English Version
Non-destructive testing - Ultrasonic testing - Specification
for step wedge calibration block (ISO 16946:2017)
Essais non destructifs - Essais par ultrasons - Zerstörungsfreie Prüfung - Ultraschallprüfung -
Spécifications relatives aux blocs d'étalonnage à Beschreibung des Stufenkeil-Kalibrierkörpers (ISO
gradins (ISO 16946:2017) 16946:2017)
This European Standard was approved by CEN on 5 February 2017.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16946:2017 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 16946:2017
EN ISO 16946:2017 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 16946:2017
EN ISO 16946:2017 (E)
European foreword
This document (EN ISO 16946:2017) has been prepared by Technical Committee ISO/TC 135 “Non-
destructive testing” in collaboration with Technical Committee CEN/TC 138 “Non-destructive testing”
the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2017, and conflicting national standards
shall be withdrawn at the latest by September 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 16946:2015.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 16946:2017 has been approved by CEN as EN ISO 16946:2017 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 16946:2017
---------------------- Page: 6 ----------------------
SIST EN ISO 16946:2017
INTERNATIONAL ISO
STANDARD 16946
Second edition
2017-03
Non-destructive testing — Ultrasonic
testing — Specification for step wedge
calibration block
Essais non destructifs — Essais par ultrasons — Spécifications
relatives aux blocs d’étalonnage à gradins
Reference number
ISO 16946:2017(E)
©
ISO 2017
---------------------- Page: 7 ----------------------
SIST EN ISO 16946:2017
ISO 16946:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 16946:2017
ISO 16946:2017(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions . 1
5 Alternative dimensions . 2
6 Material . 2
7 Preparation . 2
8 Marking . 3
9 Declaration of conformity .
...
SLOVENSKI STANDARD
kSIST FprEN ISO 16946:2016
01-december-2016
1HSRUXãLWYHQRSUHVNXãDQMH8OWUD]YRþQRSUHVNXãDQMH6SHFLILNDFLMD]DNDOLEUDFLMR
VWRSQLþDVWHJDNOLQDVWHJDEORND ,62)',6
Non-destructive testing - Ultrasonic testing - Specification for step wedge calibration
block (ISO/FDIS 16946:2016)
Zerstörungsfreie Prüfung - Ultraschallprüfung - Beschreibung des Stufenkeil-
Kalibrierkörpers (ISO/FDIS 16946:2016)
Essais non destructifs - Essais par ultrasons - Spécifications relatives aux blocs
d'étalonnage à gradins (ISO/FDIS 16946:2016)
Ta slovenski standard je istoveten z: FprEN ISO 16946
ICS:
19.100 Neporušitveno preskušanje Non-destructive testing
kSIST FprEN ISO 16946:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
kSIST FprEN ISO 16946:2016
---------------------- Page: 2 ----------------------
kSIST FprEN ISO 16946:2016
FINAL
INTERNATIONAL ISO/FDIS
DRAFT
STANDARD 16946
ISO/TC 135/SC 3
Non-destructive testing — Ultrasonic
Secretariat: DIN
testing — Specification for step wedge
Voting begins on:
2016 10 10 calibration block
Voting terminates on:
Essais non destructifs — Essais par ultrasons — Spécifications
2017 01 02
relatives aux blocs d’étalonnage à gradins
ISO/CEN PARALLEL PROCESSING
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR TING
DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO
ISO/FDIS 16946:2016(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO 2016
---------------------- Page: 3 ----------------------
kSIST FprEN ISO 16946:2016
ISO/FDIS 16946:2016(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
---------------------- Page: 4 ----------------------
kSIST FprEN ISO 16946:2016
ISO/FDIS 16946:2016(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Dimensions . 1
5 Alternative dimensions . 2
6 Material . 2
7 Preparation . 2
8 Marking . 3
9 Declaration of conformity . 3
Bibliography . 4
© ISO 2016 – All rights reserved iii
---------------------- Page: 5 ----------------------
kSIST FprEN ISO 16946:2016
ISO/FDIS 16946:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.