SIST EN 15812:2011

Polymer modified bituminous thick coatings - Determination of crack-bridging capacity

This European Standard specifies two methods (method A or method B) for determining the crack-bridging properties of polymer modified bituminous thick coatings. The two test methods may be applied equally. This European Standard has been prepared for applications in below ground structures, but it may also be used in other areas, where water proofing is relevant, e. g. balconies or wet rooms.

Kunststoffmodifizierte Bitumendickbeschichtungen - Bestimmung der Fähigkeit zur Überbrückung von Rissen

Diese Europäische Norm legt zwei Verfahren (Verfahren A oder Verfahren B) zur Bestimmung des Rissüberbrückungsvermögens von kunststoffmodifizierten Bitumendickbeschichtungen zur Bauwerks-abdichtung fest. Diese beiden Prüfverfahren können gleichrangig nebeneinander angewendet werden.

Revêtements bitumineux épais modifiés aux polymères pour imperméabilisation - Détermination de l'aptitude à ponter les fissures

La présente Norme européenne spécifie deux méthodes (méthode A et méthode B) permettant de déterminer
les propriétés de pontage des fissures des revêtements bitumineux épais modifiés aux polymères pour
imperméabilisation. Les deux méthodes peuvent être appliquées indifféremment.

Bitumenske debeloslojne prevleke za tesnjenje, modificirane s polimeri - Določanje sposobnosti premoščanja razpok

Ta evropski standard določa dve metodi (metodo A ali metodo B) za določanje sposobnosti premoščanja razpok bitumenskih debeloslojnih prevlek za tesnjenje, modificiranih s polimeri. Preskusni metodi se lahko uporabljata enako. Ta evropski standard je bil pripravljen za uporabo pri podzemnih strukturah, lahko pa se uporablja tudi na drugih območjih, kjer je hidroizolacija pomembna, npr. na balkonih ali v vlažnih prostorih.

General Information

• Status: Published
• Publication Date: 10-May-2011
• ICS: 91.100.50 - Binders. Sealing materials
• Technical Committee: VLA - Water proofing
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 13-Apr-2011
• Due Date: 18-Jun-2011
• Completion Date: 11-May-2011
• Ref Project: EN 15812:2011 - Polymer modified bituminous thick coatings for waterproofing - Determination of crack bridging ability

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kunststoffmodifizierte Bitumendickbeschichtungen - Bestimmung der Fähigkeit zur Überbrückung von RissenPolymer modified bituminous thick coatings - Determination of crack-bridging capacity91.100.50Veziva. Tesnilni materialiBinders. Sealing materialsICS:Ta slovenski standard je istoveten z:EN 15812:2011SIST EN 15812:2011en,fr,de01-junij-2011SIST EN 15812:2011SLOVENSKI
STANDARD



SIST EN 15812:2011



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 15812
March 2011 ICS 91.100.50 English Version
Polymer modified bituminous thick coatings for waterproofing - Determination of crack bridging ability
Revêtements bitumineux épais modifiés aux polymères pour imperméabilisation - Détermination de l'aptitude à ponter les fissures
Kunststoffmodifizierte Bitumendickbeschichtungen zur Bauwerksabdichtung - Bestimmung des Rissüberbrückungsvermögens This European Standard was approved by CEN on 13 February 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15812:2011: ESIST EN 15812:2011



EN 15812:2011 (E) 2 Contents Page Foreword .31 Scope .42 Normative references .43 Terms and definitions .44 Principle .45 Apparatus .46 Sampling .57 Test specimens .57.1 General .57.2 Method A .57.2.1 Substrate .57.2.2 Coating .57.2.3 Conditioning of test specimens .57.2.4 Processing bending test (method A) .57.3 Method B .67.3.1 Substrate .67.3.2 Coating .77.3.3 Conditioning of test specimens .77.3.4 Processing tensile test (method B).78 Procedure .89 Expression of results and precision .89.1 Expression of results .89.2 Precision .810 Test report .9 SIST EN 15812:2011



EN 15812:2011 (E) 3 Foreword This document (EN 15812:2011) has been prepared by Technical Committee CEN/TC 361 “Project Committee — Polymer modified bituminous thick coatings for waterproofing — Definitions/requirements and test methods”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2011, and conflicting national standards shall be withdrawn at the latest by September 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
SIST EN 15812:2011



EN 15812:2011 (E) 4 1 Scope This European Standard specifies two methods (method A and method B) for determining the crack bridge properties of polymer modified bituminous thick coatings for waterproofing. The two test methods may be applied equally. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1062-7:2004, Paints and varnishes — Coating materials and coating systems for exterior masonry and concrete — Part 7: Determination of crack bridging properties EN 1766:2
...