oSIST prEN ISO 4027:2025

Fasteners - Hexagon socket set screws with truncated cone point (ISO/DIS 4027:2025)

ISO 4027:2003 specifies the characteristics of hexagon socket set screws with cone point and threads from M1,6 up to and including M24 and of product grade A.

Verbindungselemente - Gewindestifte mit Innensechskant und abgeflachter Spitze (ISO/DIS 4027:2025)

Fixations - Vis sans tête à six pans creux, à bout tronconique (ISO/DIS 4027:2025)

L'ISO 4027:2003 spécifie les caractéristiques des vis sans tête à six pans creux, à bout tronconique, de filetage M1,6 à M24 inclus et de grade A.

Vezni element - Navojni zatiči z notranjim šestkotnikom in končino s skrajšano konico (ISO/DIS 4027:2025)

General Information

• Status: Not Published
• Public Enquiry End Date: 20-Jul-2025
• ICS: 21.060.10 - Bolts, screws, studs
• Technical Committee: ISEL - Mechanical elements
• Current Stage: 4020 - Public enquire (PE) (Adopted Project)
• Start Date: 13-May-2025
• Due Date: 30-Sep-2025
• Ref Project: prEN ISO 4027 - Fasteners - Hexagon socket set screws with truncated cone point (ISO/DIS 4027:2025)

Relations

• Revises: SIST EN ISO 4027:2004 - Hexagon socket set screws with cone point (ISO 4027:2003)
• Effective Date: 08-Nov-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-julij-2025
Vezni element - Navojni zatiči z notranjim šestkotnikom in končino s skrajšano
konico (ISO/DIS 4027:2025)
Fasteners - Hexagon socket set screws with truncated cone point (ISO/DIS 4027:2025)
Verbindungselemente - Gewindestifte mit Innensechskant und abgeflachter Spitze
(ISO/DIS 4027:2025)
Fixations - Vis sans tête à six pans creux, à bout tronconique (ISO/DIS 4027:2025)
Ta slovenski standard je istoveten z: prEN ISO 4027
ICS:
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
International
Standard
ISO/DIS 4027
ISO/TC 2/SC 11
Fasteners — Hexagon socket set
Secretariat: DIN
screws with truncated cone point
Voting begins on:
ICS: 21.060.10
2025-04-28
Voting terminates on:
2025-07-21
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 4027:2025(en)
DRAFT
ISO/DIS 4027:2025(en)
International
Standard
ISO/DIS 4027
ISO/TC 2/SC 11
Fasteners — Hexagon socket set
Secretariat: DIN
screws with truncated cone point
Voting begins on:
ICS: 21.060.10
Voting terminates on:
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2025
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: [phone]
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: [e-mail]
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 4027:2025(en)
ii
ISO/DIS 4027:2025(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Dimensions . 2
5 Requirements and reference International Standards . 4
6 Marking and labelling . 5
6.1 Marking on product . .5
6.2 Labelling on package .5
7 Designation . 5
Bibliography . 6

iii
ISO/DIS 4027:2025(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 2, Fasteners, Subcommittee SC 11, Fasteners
with metric external thread, in collaboration with the European Committee for Standardization (CEN)
Technical Committee CEN/TC 185, Fasteners, in accordance with the Agreement on technical cooperation
between ISO and CEN (Vienna Agreement).
This fourth edition cancels and replaces the third edition (ISO 4027:2003), which has been technically
revised.
The main changes are as follows:
— M30 has been added for steel hexagon socket set screws;
— the tolerances of d have been modified to 3 classes according to the values of d ;
t t,max
— approximate masses have been deleted in Table with lengths (Table 2);
— non-ferrous metal screws have been deleted (as a consequence of the withdrawal of ISO 8839);
— for stainless steel fasteners, “Plain” has been changed to “Clean and bright”, and “Passivated” has been
added in Table 3;
— specifications for marking and labelling have been added as Clause 6.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.

iv
DRAFT International Standard ISO/DIS 4027:2025(en)
Fasteners — Hexagon socket set screws with truncated
cone point
1 Scope
This document specifies the characteristics of hexagon socket set screws with truncated cone point, with
metric coarse pitch threads M1,6 to M30 for steel and M1,6 to M24 for stainless steel, and with product
grade A.
Set screws are not intended for use under tensile load.
If in certain cases other specifications are requested, hardness classes and
...