SIST EN 60695-1-30:2009

Fire hazard testing -- Part 1-30: Guidance for assessing the fire hazard of electrotechnical products - Preselection testing process - General guidelines

This part of IEC 60695 provides guidance for assessing and choosing candidate materials, components or sub-assemblies for making an end-product based upon preselection testing. It describes how preselection provides comparative fire hazard test methods to evaluate the performance of a test specimen and how preselection can be used in the selection of materials, parts, components and sub-assemblies during the design stage of an end-product. It further describes how standardized test methods may be used as one part in the decision making processes directed to minimize the fire hazards from electrotechnical equipment. It states that one should take into account the desired reaction to fire properties of the endproduct, and that one should consider the possible effects of environmental conditions on the behaviour of the end-product. This basic safety publication is intended for use by technical committees in the preparation of standards in accordance with the principles laid down in IEC Guide 104 and ISO/IEC Guide 51. One of the responsibilities of a technical committee is, wherever applicable, to make use of basic safety publications in the preparation of its publications. The requirements, test methods or test conditions of this basic safety publication will not apply unless specifically referred to or included in the relevant publications.

Prüfungen zur Beurteilung der Brandgefahr - Teil 1-30: Anleitung zur Beurteilung der Brandgefahr von elektrotechnischen Erzeugnissen - Anwendung von Vorauswahlverfahren - Allgemeiner Leitfaden

Essais relatifs aux risques du feu -- Partie 1-30: Lignes directrices pour l’évaluation des risques du feu des produits électrotechniques - Processus d’essais de présélection - Lignes directrices générales

La CEI 60695-1-30:2008 fournit des lignes directrices pour l'évaluation et le choix des matériaux, composants et sous-ensembles candidats en vue de l'élaboration d'un produit fini fondé sur des essais de présélection. Elle décrit la manière dont la présélection fournit des méthodes d'essai comparatives sur les risques du feu  pour évaluer la performance d'une éprouvette et la façon dont la  présélection peut être utilisée dans la sélection des matériaux,  des parties, des composants et des sous-ensembles pendant la phase   de conception d'un produit fini. Les principales modifications par rapport à l'édition antérieure sont indiquées ci-dessous:  - Explications supplémentaires fournies dans l'introduction et le domaine d'application  - Article 3 modifications apportées aux définitions  - Article 4 éclaircissements des principes de conception des produits en prenant en compte la présélection  - Article 5 éclaircissements des avantages et des limites de las présélection  - Article 6 éclaircissements des aspects de la présélection par rapport à l'évaluation des risques  - Annexe A modification des références, par exemple des méthodes d'essai qui pervent être applicables à la présélection  - Annexe B modifications de l'exemple illustratif de l'organigramme d'utilisation des essais de présélection pour la résistance aux risques du feu d'un type de produit spécifique.  Elle a le statut de publication fondamentale de sécurité, conformément au Guide CEI 104 et au Guide ISO/CEI 51.

Preskušanje požarne ogroženosti - 1-30. del: Vodilo za ocenjevanje požarne varnosti elektrotehniških izdelkov - Predizbira preskusnih procesov - Splošno vodilo (IEC 60695-1-30:2008)

General Information

• Status: Withdrawn
• Publication Date: 30-Nov-2008
• Withdrawal Date: 19-Apr-2020
• ICS: 13.220.40 - Ignitability and burning behaviour of materials and products
• ICS: 29.020 - Electrical engineering in general
• Technical Committee: I09 - Imaginarni 09
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 17-Apr-2020
• Due Date: 10-May-2020
• Completion Date: 20-Apr-2020
• Ref Project: EN 60695-1-30:2008 - Fire hazard testing - Part 1-30: Guidance for assessing the fire hazard of electrotechnical products - Preselection testing process - General guidelines

Relations

• Replaces: SIST EN 60695-1-30:2003 - Fire hazard testing - Part 1-30: Guidance for assessing the fire hazard of electrotechnical products - Use of preselection testing procedures
• Effective Date: 01-Jan-2012
• Replaced By: SIST EN 60695-1-30:2017 - Fire hazard testing - Part 1-30: Guidance for assessing the fire hazard of electrotechnical products - Preselection testing process - General guidelines (IEC 60695-1-30:2017)
• Effective Date: 30-May-2017
• Replaced By: SIST EN 60695-1-30:2017 - Fire hazard testing - Part 1-30: Guidance for assessing the fire hazard of electrotechnical products - Preselection testing process - General guidelines (IEC 60695-1-30:2017)
• Effective Date: 07-Jun-2022
• Replaces: SIST EN 60695-1-30:2003 - Fire hazard testing - Part 1-30: Guidance for assessing the fire hazard of electrotechnical products - Use of preselection testing procedures
• Effective Date: 29-Jan-2023
• Revised: SIST EN 60695-1-30:2017 - Fire hazard testing - Part 1-30: Guidance for assessing the fire hazard of electrotechnical products - Preselection testing process - General guidelines (IEC 60695-1-30:2017)
• Effective Date: 04-Aug-2015
• Replaces: SIST EN 60695-1-30:2003 - Fire hazard testing - Part 1-30: Guidance for assessing the fire hazard of electrotechnical products - Use of preselection testing procedures
• Effective Date: 07-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60695-1-30:2009
01-januar-2009
1DGRPHãþD
SIST EN 60695-1-30:2003
Preskušanje požarne ogroženosti - 1-30. del: Vodilo za ocenjevanje požarne
varnosti elektrotehniških izdelkov - Predizbira preskusnih procesov - Splošno
vodilo (IEC 60695-1-30:2008)
Fire hazard testing -- Part 1-30: Guidance for assessing the fire hazard of
electrotechnical products - Preselection testing process - General guidelines
Prüfungen zur Beurteilung der Brandgefahr - Teil 1-30: Anleitung zur Beurteilung der
Brandgefahr von elektrotechnischen Erzeugnissen - Anwendung von
Vorauswahlverfahren - Allgemeiner Leitfaden
Essais relatifs aux risques du feu -- Partie 1-30: Lignes directrices pour l’évaluation des
risques du feu des produits électrotechniques - Processus d’essais de présélection -
Lignes directrices générales
Ta slovenski standard je istoveten z: EN 60695-1-30:2008
ICS:
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
29.020 Elektrotehnika na splošno Electrical engineering in
general
SIST EN 60695-1-30:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60695-1-30:2009

---------------------- Page: 2 ----------------------

SIST EN 60695-1-30:2009

EUROPEAN STANDARD
EN 60695-1-30

NORME EUROPÉENNE
October 2008
EUROPÄISCHE NORM

ICS 13.220.40; 29.020 Supersedes EN 60695-1-30:2002


English version


Fire hazard testing -
Part 1-30: Guidance for assessing the fire hazard
of electrotechnical products -
Preselection testing process -
General guidelines
(IEC 60695-1-30:2008)


Essais relatifs aux risques du feu -  Prüfungen zur Beurteilung
Partie 1-30: Lignes directrices der Brandgefahr -
pour l’évaluation des risques du feu Teil 1-30: Anleitung zur Beurteilung
des produits électrotechniques - der Brandgefahr
Processus d’essais de présélection - von elektrotechnischen Erzeugnissen -
Lignes directrices générales Anwendung von Vorauswahlverfahren -
(CEI 60695-1-30:2008) Allgemeiner Leitfaden
(IEC 60695-1-30:2008)


This European Standard was approved by CENELEC on 2008-10-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: rue de Stassart 35, B - 1050 Brussels


© 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60695-1-30:2008 E

---------------------- Page: 3 ----------------------

SIST EN 60695-1-30:2009
EN 60695-1-30:2008 - 2 -
Foreword
The text of document 89/865/FDIS, future edition 2 of IEC 60695-1-30, prepared by IEC TC 89, Fire
hazard testing, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as
EN 60695-1-30 on 2008-10-01.
This European Standard supersedes EN 60695-1-30:2002.
The main changes with respect to EN 60695-1-30:2002 are listed below:
– further explanation given in the introduction and scope;
– Clause 3: changes to the definitions;
– Clause 4: clarifications of the principles of product design considering preselection;
– Clause 5: clarifications of the advantages and limitations of preselection;
– Clause 6: clarifications of the aspects of preselection relative to hazard assessment;
– Annex A: changes in the references for examples of test methods which may be relevant to
preselection;
– Annex B: changes in the illustrative example of the flowchart of the use of preselection tests for
resistance to fire hazards of a specific product type.
1) 1)
This standard is to be used in conjunction with the future IEC 60695-1-10 and IEC 60695-1-11 .
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2009-07-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2011-10-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60695-1-30:2008 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 60950-1 NOTE  Harmonized as EN 60950-1:2006 (modified).
__________


1)
Under consideration.

---------------------- Page: 4 ----------------------

SIST EN 60695-1-30:2009
- 3 - EN 60695-1-30:2008
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

IEC 60695-4 2005 Fire hazard testing - EN 60695-4 2006
Part 4: Terminology concerning fire tests
for electrotechnical products


IEC Guide 104 1997 The preparation of safety publications - -
and the use of basic safety publications
and group safety publications


ISO/IEC Guide 51 1999 Safety aspects - - -
Guidelines for their inclusion in standards


ISO 13943 2000 Fire safety - Vocabulary EN ISO 13943 2000

---------------------- Page: 5 ----------------------

SIST EN 60695-1-30:2009

---------------------- Page: 6 ----------------------

SIST EN 60695-1-30:2009



IEC 60695-1-30
Edition 2.0 2008-07
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
BASIC SAFETY PUBLICATION
PUBLICATION FONDAMENTALE DE SÉCURITÉ
Fire hazard testing –
Part 1-30: Guidance for assessing the fire hazard of electrotechnical products –
Preselection testing process – General guidelines

Essais relatifs aux risques du feu –
Partie 1-30: Lignes directrices pour l’évaluation des risques du feu des produits
électrotechniques – Processus d’essai de présélection – Lignes directrices
générales

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
M
CODE PRIX
ICS 13.220.40; 29.020 ISBN 2-8318-9855-2
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60695-1-30:2009
– 2 – 60695-1-30 © IEC:2008
CONTENTS
FOREWORD.3
INTRODUCTION.5
1 Scope.6
2 Normative references .6
3 Terms and definitions .6
4 Principles of product design considering preselection.7
5 Advantages and limitations of preselection .8
6 Aspects of preselection relative to hazard assessment .8
Annex A (informative) Examples of test methods .9
Annex B (informative) Use of preselection tests for flammability requirements for fire
enclosure materials used in information technology equipment (ITE) – Illustrative
example.11
Bibliography.13

Figure B.1 – Flammability requirements for fire enclosure materials used in information
technology equipment .12

Table 1 – Some of the factors which can affect fire performance in preselection tests .7

---------------------- Page: 8 ----------------------

SIST EN 60695-1-30:2009
60695-1-30 © IEC:2008 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

FIRE HAZARD TESTING –


Part 1-30: Guidance for assessing the fire
hazard of electrotechnical products –
Preselection testing process –
General guidelines


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60695-1-30 has been prepared by IEC technical committee 89:
Fire hazard testing.
This second edition cancels and replaces the first edition of IEC 60695-1-30, published in
2002, and constitutes a technical revision.
The main changes with respect to the previous edition are listed below:
– Further explanation given in the introduction and scope.
– Clause 3: changes to the definitions.
– Clause 4: clarifications of the principles of product design considering preselection.
– Clause 5: clarifications of the advantages and limitations of preselection.
– Clause 6: clarifications of the aspects of preselection relative to hazard assessment.

---------------------- Page: 9 ----------------------

SIST EN 60695-1-30:2009
– 4 – 60695-1-30 © IEC:2008
– Annex A: changes in the references for examples of test methods which may be relevant
to preselection.
– Annex B: changes in the illustrative example of the flowchart of the use of preselection
tests for resistance to fire hazards of a specific product type.
It has the status of a basic safety publication in accordance with IEC Guide 104 and
ISO/IEC Guide 51.
The text of this standard is based on the following documents:
FDIS Report on voting
89/865/FDIS 89/869/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
1
This publication is to be used in conjunction with the future IEC 60695-1-10 and IEC 60695-
1
1-11 .
A list of all parts in the IEC 60695 series, under the general title Fire hazard testing, can be
found on the IEC website.
Part 1 consists of the following sub-parts:
1
Part 1-10 : Guidance for assessing the fire hazard of electrotechnical products –
General guidelines
1
Part 1-11 : Guidance for assessing the fire hazard of electrotechnical products –
Fire hazard assessment
Part 1-20: Guidance for assessing the fire hazard of electrotechnical products –
Ignitability – General guidance
Part 1-21: Guidance for assessing the fire hazard of electrotechnical products –
Ignitability – Summary and relevance of test methods
Part 1-30: Guidance for assessing the fire hazard of electrotechnical products –
Preselection testing process – General guidelines
Part 1-40: Guidance for assessing the fire hazard of electrotechnical products –
Insulating liquids
The committee has decided that the contents of this publication will remain unchanged until

the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in the
data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
___________
1
Under consideration.

---------------------- Page: 10 ----------------------

SIST EN 60695-1-30:2009
60695-1-30 © IEC:2008 – 5 –
INTRODUCTION
In the design of any electrotechnical product, the risk of fire and the potential hazards
associated with fire need to be considered. In this respect the objective of component, circuit
and equipment design as well as the choice of materials is to reduce to acceptable levels the
potential risks of fire even in the event of foreseeable abnormal use, malfunction or failure.
2
2
The future IEC 60695-1-10 and IEC 60695-1-11 provide guidance on how this is to be
accomplished using quantitative and qualitative fire tests.
The information gained from properly designed small-scale tests can be used as an aid for the
preselection of proper materials, parts, components or sub-assemblies with regard to the fire
hazard evaluation of the final en
...