SIST EN ISO 14530-1:2000

Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Part 1: Designation system and basis for specifications (ISO 14530-1:1999)

1.1 This part of ISO 14530 establishes a data block system for the designation of unsaturated-polyester powder
moulding compounds (UP-PMCs).
1.2 The various types of UP-PMC are differentiated from each other by a classification system based on
information about the filler/reinforcement type and content, the intended method of processing, any special
properties and those of the special properties used specifically for designation purposes (designatory properties).
1.3 This part of ISO 14530 is applicable to all UP-PMCs ready for normal use in the form of powder, granules or
ground material.
1.4 It is not intended to imply that materials having the same designation necessarily give the same
performance. This part of ISO 14530 does not provide engineering data, performance data or data on processing
conditions which may be required to specify a material for a particular application and/or method of processing. If
such additional properties are required, they shall be determined in accordance with the test methods specified in
ISO 14530-2, if suitable.
1.5 Whenever general requirement data, as covered by ISO 14530-3, need to be indicated, this is also done
using this data block system.
1.6 To ensure that code-letters and code-numbers remain unambiguous, and to avoid conflicts within the
system, any new code-letters or code-numbers for use in data block 1, 2 or 3 shall be approved before use by the
secretariats of ISO/TC 61/SC 1, SC 12 and SC 13.

Kunststoffe - Rieselfähige ungesättigte Polyester-Formmassen (UP-PMC) - Teil 1: Bezeichnungssystem und Basis für Spezifikationen (ISO 14530-1:1999)

1.1 In diesem Teil von ISO 14530 wird ein Daten-Blocksystem zur Bezeichnung von Rieselfähigen ungesättigten Polyester-Formmassen (UP-PMC) festgelegt. 1.2 Die verschiedenen Typen von UP-PMC werden mit einem Einteilungssystem voneinander unterschieden, das auf Angaben über Füll-/Verstärkungsstoffanteil und Art, vorgesehene Verarbeitungs- und/oder Herstellungsverfahren, Angaben zu besonderen Eigenschaften und jenen besonderen Eigenschaften beruht, die spezifisch zur Bezeichnung verwendet werden (kennzeichnende Eigenschaften).

Plastiques - Poudres a mouler a base de polyester non saturé (UP-PMC) - Partie 1: Systeme de désignation et base de spécification (ISO 14530-1:1999)

1.1 La présente partie de l'ISO 14530 établit un système de blocs de données pour la désignation des poudres à
mouler à base de polyester non saturé (UP-PMC).
1.2 Les types d'UP-PMC sont différenciés les uns des autres par un système de classification basé sur des
informations relatives à la nature et à la teneur en charges/matériaux de renforcement, à la méthode de mise en
oeuvre prévue, aux propriétés particulières en général et à celles utilisées spécifiquement pour les besoins de la
désignation (propriétés de désignation).
1.3 La présente partie de l'ISO 14530 est applicable à tous les UP-PMC prêts à l'emploi pour un usage courant
sous forme de poudres, grains ou matériaux broyés.
1.4 Le fait que des matériaux aient la même désignation n'implique pas qu'ils présentent nécessairement les
mêmes performances. La présente partie de l'ISO 14530 ne comporte pas de données sur la conception, les
performances ou les conditions de mise en oeuvre qui peuvent être exigées pour spécifier un matériau pour une
application et/ou une méthode de mise en oeuvre particulière. Si de telles caractéristiques supplémentaires sont
nécessaires, elles doivent être déterminées conformément aux méthodes d'essai spécifiées dans l'ISO 14530-2, le
cas échéant.
1.5 Chaque fois qu'il est nécessaire d'indiquer certaines exigences générales telles que traitées dans
l'ISO 14530-3, on utilise pour ce faire le présent système de blocs de données.
1.6 Pour garantir que la signification des lettres-codes et des nombres-codes demeure non ambiguë et pour
éviter toute contradiction au sein du système, les nouveaux lettres-codes et nombres-codes à utiliser dans les
blocs de données 1, 2 et 3 doivent être approuvés par les secrétariats de l'ISO/TC 61/SC 1, SC 12 et SC 13 avant
utilisation.

Polimerni materiali - Praškaste zmesi za oblikovanje na osnovi nenasičenih poliestrov (UP- PMCS) - 1. del: Sistem označevanja in podlage za specifikacije (ISO 14530-1:1999)

General Information

• Status: Published
• Publication Date: 30-Nov-2000
• ICS: 83.080.10 - Thermosetting materials
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Dec-2000
• Due Date: 01-Dec-2000
• Completion Date: 01-Dec-2000
• Ref Project: EN ISO 14530-1:1999 - Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Part 1: Designation system and basis for specifications (ISO 14530-1:1999)

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.QDVLþHQLKKunststoffe - Rieselfähige ungesättigte Polyester-Formmassen (UP-PMC) - Teil 1: Bezeichnungssystem und Basis für Spezifikationen (ISO 14530-1:1999)Plastiques - Poudres a mouler a base de polyester non saturé (UP-PMC) - Partie 1: Systeme de désignation et base de spécification (ISO 14530-1:1999)Plastics - Unsaturated-polyester powder moulding compounds (UP-PMCs) - Part 1: Designation system and basis for specifications (ISO 14530-1:1999)83.080.10DuromeriThermosetting materialsICS:Ta slovenski standard je istoveten z:EN ISO 14530-1:1999SIST EN ISO 14530-1:2000en01-december-2000SIST EN ISO 14530-1:2000SLOVENSKI
STANDARD



SIST EN ISO 14530-1:2000



SIST EN ISO 14530-1:2000



SIST EN ISO 14530-1:2000



ReferencenumberISO14530-1:1999(E)©ISO1999INTERNATIONALSTANDARDISO14530-1Firstedition1999-11-15Plastics—Unsaturated-polyesterpowdermouldingcompounds(UP-PMCs)—Part1:DesignationsystemandbasisforspecificationsPlastiques—Poudresàmouleràbasedepolyesternonsaturé(UP-PMC)—Partie1:SystèmededésignationetbasedespécificationSIST EN ISO 14530-1:2000



ISO14530-1:1999(E)©ISO1999Allrightsreserved.Unlessotherwisespecified,nopartofthispublicationmaybereproducedorutilizedinanyformorbyanymeans,electronicormechanical,includingphotocopyingandmicrofilm,withoutpermissioninwritingfromeitherISOattheaddressbeloworISO'smemberbodyinthecountryoftherequester.ISOcopyrightofficeCasepostal[e-mail]©ISO1999–AllrightsreservedPDFdisclaimerThisPDFfilemaycontainembeddedtypefaces.InaccordancewithAdobe'slicensingpolicy,thisfilemaybeprintedorviewedbutshallnotbeeditedunlessthetypefaceswhichareembeddedarelicensedtoandinstalledonthecomputerperformingtheediting.Indownloadingthisfile,partiesacceptthereintheresponsibilityofnotinfringingAdobe'slicensingpolicy.TheISOCentralSecretariatacceptsnoliabilityinthisarea.AdobeisatrademarkofAdobeSystemsIncorporated.DetailsofthesoftwareproductsusedtocreatethisPDFfilecanbefoundintheGeneralInforelativetothefile;thePDF-creationparameterswereoptimizedforprinting.EverycarehasbeentakentoensurethatthefileissuitableforusebyISOmemberbodies.Intheunlikelyeventthataproblemrelatingtoitisfound,pleaseinformtheCentralSecretariatattheaddressgivenbelow.SIST EN ISO 14530-1:2000



ISO14530-1:1999(E)©ISO1999–AllrightsreservediiiForewordISO(theInternationalOrganizationforStandardization)isaworldwidefederationofnationalstandardsbodies(ISOmemberbodies).TheworkofpreparingInternationalStandardsisnormallycarriedoutthroughISOtechnicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeenestablishedhastherighttoberepresentedonthatcommittee.Internationalorganizations,governmentalandnon-governmental,inliaisonwithISO,alsotakepartinthework.ISOcollaboratescloselywiththeInternationalElectrotechnicalCommission(IEC)onallmattersofelectrotechnicalstandardization.InternationalStandardsaredraftedinaccordancewiththerulesgivenintheISO/IECDirectives,Part3.DraftInternationalStandardsadoptedbythetechnicalcommitteesarecirculatedtothememberbodiesforvoting.PublicationasanInternationalStandardrequiresapprovalbyatleast75%ofthememberbodiescastingavote.AttentionisdrawntothepossibilitythatsomeoftheelementsofthispartofISO14530maybethesubjectofpatentrights.ISOshallnotbeheldresponsibleforidentifyinganyorallsuchpatentrights.InternationalStandardISO14530-1waspreparedbyTechnicalCommitteeISO/TC61,Plastics,SubcommitteeSC12,Thermosettingmaterials.ISO14530consistsofthefollowingparts,underthegeneraltitlePlastics—Unsaturated-polyesterpowdermouldingcompounds(UP-PMCs):Part1:DesignationsystemandbasisforspecificationsPart2:PreparationoftestspecimensanddeterminationofpropertiesPart3:RequirementsforselectedmouldingcompoundsSIST EN ISO 14530-1:2000



SIST EN ISO 14530-1:2000



INTERNATIONALSTANDARDISO14530-1:1999(E)©ISO1999–Allrightsreserved1Plastics—Unsaturated-polyesterpowdermouldingcompounds(UP-PMCs)—Part1:Designationsystemandbasisforspecifications1Scope1.1ThispartofISO14530establishesadatablocksystemforthedesignationofunsaturated-polyesterpowdermouldingcompounds(UP-PMCs).1.2ThevarioustypesofUP-PMCaredifferentiatedfromeachotherbyaclassificationsystembasedoninformationaboutthefiller/reinforcementtypeandcontent,theintendedmethodofprocessing,anyspecialpropertiesandthoseofthespecialpropertiesusedspecificallyfordesignationpurposes(designatoryproperties).1.3ThispartofISO14530isapplicabletoallUP-PMCsreadyfornormaluseintheformofpowder,granulesorgroundmaterial.1.4Itisnotintendedtoimplythatmaterialshavingthesamedesignationnecessarilygivethesameperformance.ThispartofISO14530doesnotprovideengineeringdata,performancedataordataonprocessingconditionswhichmayberequiredtospecifyamaterialforaparticularapplicationand/ormethodofprocessing.Ifsuchadditionalpropertiesarerequired,theyshallbedeterminedinaccordancewiththetestmethodsspecifiedinISO14530-2,ifsuitable.1.5Whenevergeneralrequirementdata,ascoveredbyISO14530-3,needtobeindicated,thisisalsodoneusingthisdatablocksystem.1.6Toensurethatcode-lettersandcode-numbersremainunambiguous,andtoavoidconflictswithinthesystem,anynewcode-lettersorcode-numbersforuseindatablock1,2or3shallbeapprovedbeforeusebythesecretariatsofISO/TC61/SC1,SC12andSC13.2NormativereferencesThefollowingnormativedocumentscontainprovisionswhich,throughreferenceinthistext,constituteprovisionsofthispartofISO14530.Fordatedreferences,subsequentamendmentsto,orrevisionsof,anyofthesepublicationsdonotapply.However,partiestoagreementsbasedonthispartofISO14530areencouragedtoinvestigatethepossibilityofapplyingthemostrecenteditionsofthenormativedocumentsindicatedbelow.Forundatedreferences,thelatesteditionofthenormativedocumentreferredtoapplies.MembersofISOandIECmaintainregistersofcurrentlyvalidInternationalStandards.ISO75-2:1993,Plastics—Determinationoftemperatureofdeflectionunderload—Part2:Plasticsandebonite.ISO179-1:—1),Plastics—DeterminationofCharpyimpactproperties—Part1:Non-instrumentedimpacttest.1)Tobepublished.(RevisionofISO179:1993)SIST EN ISO 14530-1:2000



ISO14530-1:1999(E)2©ISO1999–AllrightsreservedISO472:1999,Plastics—Vocabulary.ISO1043-1:1997,Plastics—Symbolsandabbreviatedterms—Part1:Basicpolymersandtheirspecialcharacteristics.ISO1043-2:—2),Plastics—Symbolsandabbreviatedterms—Part2:Fillersandreinforcingmaterials.ISO14530-2:1999,Plastics—Unsaturated-polyesterpowdermouldingcompounds(UP-PMCs)—Part2:Preparationoftestspecimensanddeterminationofproperties.ISO14530-3:1999,Plasti
...