SIST EN 13706-3:2003

Reinforced plastics composites - Specifications for pultruded profiles - Part 3: Specific requirements

This part 3 Of ENxxxx defines the specification of pultruded profiles. The specification defines those properties which shall be specified and the level to be obtained for each grade of profile. The specification defines grades where the short-form code, Exx, is related to the Young's modulus of the material measured by testing a length of the full section profile. Two grades; E23 and E17 are defined. Note: Other grades may be introduced at future revisions of the standard. The properties which shall be achieved for each class of profile are given in Table 1. Other properties that may be reported are listed in Table 2.

Verstärkte Kunststoffverbundwerkstoffe - Spezifikationen für pultrudierte Profile - Teil 3: Besondere Anforderungen

1.1   Dieser Teil 3 von EN 13706 legt die Spezifikation für pultrudierte Profile fest. Die Spezifikation nennt jene Eigenschaften, die festgelegt werden müssen, und das für jede Profilsorte zu erreichende Niveau.
1.2   Die Spezifikation legt Sorten fest, bei denen sich der Kurzformcode Exx auf den durch Prüfung einer Länge des Gesamtprofils bestimmten effektiven Biegemodul des Profils bezieht.
Es sind zwei Sorten, E23 und E17, festgelegt.
ANMERKUNG   Weitere Sorten können bei zukünftigen Überarbeitungen der Norm eingeführt werden.
1.3   Die Eigenschaften, die bei jeder Profilklasse erreicht werden müssen, sind in Tabelle 1 angegeben. Weitere Eigenschaften, die angegeben werden können, sind in Tabelle 2 aufgeführt.
1.4   Die anzuwendenden Prüfverfahren zur Bestimmung der Eigenschaften für die Eignung des Profils für besondere Anwendungen sind Abschnitt 4 zu entnehmen.

Composites en plastiques renforcés - Spécifications pour les profilés pultrudés - Partie 3: Exigences spécifiques

1.1   La présente partie 3 de l'EN 13706 spécifie la spécification relative aux profilés pultrudés. Cette spécification définit les propriétés devant etre spécifiées et le niveau a obtenir pour chaque qualité de profilé.
1.2   Cette spécification spécifie les qualités a l'aide du code abrégé, Exx, correspondant au module effectif de flexion du matériau mesuré en soumettant a essai un segment de profilé de section pleine.
Deux qualités, E 23 et E 17, sont définies.
NOTE   D'autres qualités peuvent etre introduites dans les révisions ultérieures de la norme.
1.3   Les propriétés devant etre obtenues pour chaque classe de profilés sont indiquées dans le Tableau 1. Les autres propriétés pouvant etre consignées sont énumérées dans le Tableau 2.
1.4   Les méthodes d'essai devant etre utilisées pour indiquer les propriétés attestant que le profilé est adapté aux applications spécifiques sont mentionnées a l'article 4.

Ojačeni polimerni kompoziti - Specifikacije za pultrudirane profile - 3. del: Posebne zahteve

General Information

• Status: Published
• Publication Date: 30-Apr-2003
• ICS: 83.120 - Reinforced plastics
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-May-2003
• Due Date: 01-May-2003
• Completion Date: 01-May-2003
• Ref Project: EN 13706-3:2002 - Reinforced plastics composites - Specifications for pultruded profiles - Part 3: Specific requirements

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Verstärkte Kunststoffverbundwerkstoffe - Spezifikationen für pultrudierte Profile - Teil 3: Besondere AnforderungenComposites en plastiques renforcés - Spécifications pour les profilés pultrudés - Partie 3: Exigences spécifiquesReinforced plastics composites - Specifications for pultruded profiles - Part 3: Specific requirements83.120Reinforced plasticsICS:Ta slovenski standard je istoveten z:EN 13706-3:2002SIST EN 13706-3:2003en01-maj-2003SIST EN 13706-3:2003SLOVENSKI
STANDARD



SIST EN 13706-3:2003



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13706-3October 2002ICS 83.120; 83.140.99English versionReinforced plastics composites - Specifications for pultrudedprofiles - Part 3: Specific requirementsComposites en plastiques renforcés - Spécifications desprofilés pultrudés - Partie 3: Exigences pariculièresVerstärkte Kunststoffverbundwerkstoffe - Spezifikationenfür pultrudierte Profile - Teil 3: Besondere AnforderungenThis European Standard was approved by CEN on 14 September 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13706-3:2002 ESIST EN 13706-3:2003



EN 13706-3:2002 (E)2ContentspageForeword.31Scope.42Normative references.43Terms and definitions.44Specification.44.1Obligatory specified properties.44.2Other properties which may be reported.54.3Specific performance properties.54.4Other requirements.5Bibliography.7SIST EN 13706-3:2003



EN 13706-3:2002 (E)3ForewordThis document EN 13706-3:2002 has been prepared by Technical Committee CEN/TC 249 "Plastics", thesecretariat of which is held by IBN.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by April 2003, and conflicting national standards shall be withdrawn at the latest byApril 2003.Part 3 of this European Standard, EN 13706, defines the specification of pultruded profiles. The specificationdefines those properties, which shall be specified and the level to be obtained for each grade of profile. Twogrades; E23 and E17 are defined.EN 13706 consists of the following parts, under the general title Reinforced plastics composites - Specifications forpultruded profiles.¾ Part 1: Designation¾ Part 2: Methods of tests and general requirements¾ Part 3: Specific requirementsAccording to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain,Sweden, Switzerland and the United Kingdo
...