SIST EN 62317-9:2007
(Main)Ferrite cores - Dimensions -- Part 9: Planar cores
Ferrite cores - Dimensions -- Part 9: Planar cores
This International Standard specifies the shapes and dimensions of ferrite cores for inductive components (transformers and chokes) of which the coil is typically constructed by multi-layer board or the coil is part of the motherboard. The general consideration upon which the design of this range of cores is based is given in Annex A.
Ferritkerne - Maße -- Teil 9: Planarkerne
Noyaux ferrites - Dimensions -- Partie 9: Noyaux planaires
Feritna jedra – Mere – 9. del: Planarna jedra (IEC 62317-9:2006)
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Ferrite cores - Dimensions -- Part 9: Planar cores (IEC 62317-9:2006)Feritna jedra – Mere – 9. del: Planarna jedra (IEC 62317-9:2006)Noyaux ferrites - Dimensions -- Partie 9: Noyaux planaires (IEC 62317-9:2006)Ferritkerne - Maße -- Teil 9: Planarkerne (IEC 62317-9:2006)Ta slovenski standard je istoveten z:EN 62317-9:2006SIST EN 62317-9:2007en,de29.100.10Magnetne komponenteMagnetic componentsICS:SIST EN 61860:20021DGRPHãþDSLOVENSKI
STANDARDSIST EN 62317-9:200701-september-2007
EUROPEAN STANDARD EN 62317-9 NORME EUROPÉENNE
EUROPÄISCHE NORM September 2006
CENELEC European Committee for Electrotechnical Standardization Comité Européen de Normalisation Electrotechnique Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2006 CENELEC -
All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 62317-9:2006 E
ICS 29.100.10 Supersedes EN 61860:2000
English version
Ferrite cores - Dimensions Part 9: Planar cores (IEC 62317-9:2006)
Noyaux ferrites - Dimensions Partie 9: Noyaux planaires (CEI 62317-9:2006)
Ferritkerne - Maße Teil 9: Planarkerne (IEC 62317-9:2006)
This European Standard was approved by CENELEC on 2006-07-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member.
This European Standard exists in two official versions (English and German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
EN 62317-9:2006
- 2 - Foreword The text of document 51/849/FDIS, future edition 1 of IEC 62317-9, prepared by IEC TC 51, Magnetic components and ferrite materials, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 62317-9 on 2006-07-01. This European Standard supersedes EN 61860:2000. This European Standard includes the following significant changes and additions with respect to EN 61860:2000: a)
addition of the planar EL family of cores; b)
addition of the low-profile ER family of cores; c)
the low-profile RM-family defined in EN 61860:2000 has been moved to EN 62317-4 for RM-cores and associated parts. The following dates were fixed: – latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement
(dop)
2007-04-01 – latest date by which the national standards conflicting
with the EN have to be withdrawn
(dow)
2009-07-01 Annex ZA has been added by CENELEC. __________ Endorsement notice The text of the International Standard IEC 62317-9:2006 was approved by CENELEC as a European Standard without any modification. __________
- 3 - EN 62317-9:2006
Annex ZA
(normative)
Normative references to international publications with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.
NOTE
When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD applies.
Publication Year Title EN/HD Year
IEC 60205 -1) Calculation of the effective parameters of magnetic piece parts EN 60205 20062)
IEC 62317-4 2005 Ferrite cores - Dimensions
Part 4: RM-cores and associated parts EN 62317-4 2005
1) Undated reference. 2) Valid edition at date of issue.
INTERNATIONAL STANDARD IEC62317-9 Edition 1.12007-03 Ferrite cores – Dimensions – Part 9: Planar cores
© IEC 2007
⎯
Copyright - all rights reserved No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Electrotechnical Commission,
3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, SwitzerlandTelephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch
Web: www.iec.ch CDFor price, see current catalogue PRICE CODE
Commission Electrotechnique InternationaleInternational Electrotechnical Commission
Edition 1:2006consolidated with amendment 1:2007
– 2 – 62317-9 © IEC:2006+A1:2007(E) CONTENTS
FOREWORD.3 INTRODUCTION.5
1 Scope.6 2 Normative references.6 3 Primary standards.6 3.1 Planar shape and dimensions.6 3.2 Dimensions of planar core EL and the mating PLT-core.7 3.3 Dimensions of low-profile core E-core and the mating PLT-core.9 3.4 Dimensions of low-profile core ER-core.11
Annex A (normative) Low-profile core design.15
Figure 1 – Planar core EL and the mating PLT-core.7 Figure 2 – Low-profile E-core and the mating PLT-core.9 Figure 3 – Low-profile ER-core.11
Table 1 – Dimensions of planar core EL and the mating PLT-core.7 Table 2 – Effective parameter values and Amin values.8 Table 3 – Dimensions of low-profile E-core and the mating PLT-core.9 Table 4 – Effective parameter values and Amin values.10 Table 5 – Dimensions of low-profile ER-core.12 Table 6 – Effective parameter values and Amin values.14 Table A.1 – Sizes and design ratios for ER-core.17
62317-9 © IEC:2006+A1:2007(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION ____________
FERRITE CORES – DIMENSIONS –
Part 9: Planar cores
FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards. Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)“). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4)
In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5)
IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6)
All users should ensure that they have the latest edition of this publication. 7)
No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8)
Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9)
Attention is drawn to the possibility that some of the elements of this IEC publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 62317-9 has been prepared IEC technical committee 51: Magnetic components and ferrite materials. This International Standard cancels and replaces IEC 61860 published in 2000. This edition constitutes a technical revision. This International Standard includes the following significant technical changes and additions with respect to IEC 61860:2000: a) addition of the planar EL family of cores; b) addition of the low-profile ER family of cores; c) the low-profile RM-family defined in IEC 61860:2000 has been moved to IEC 62137-4 for RM-cores and associated parts.
– 4 – 62317-9 © IEC:2006+A1:2007(E) This consolidated version of IEC 62317-9 is based on the first edition (2006) [documents 51/849/FDIS and 51/858/RVD] and its amendment 1 (2007) [documents 51/866/CDV and 51/876/RVC]. It bears the edition number 1.1. A vertical line in the margin shows where the base publication has been modified by amendment 1. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. IEC 62317 consists of the following parts, under the general title Ferrite cores – Dimensions: Part 1:
General (under consideration) Part 2:
Pot cores (under consideration, currently available as IEC 60133) Part 3:
Half pot cores (under consideration, currently available as IEC 62323) Part 4:
RM-cores and associated parts Part 5:
EP-cores (under consideration, currently available as IEC 61596) Part 6:
ETD-cores (under consideration, currently available as IEC 61185) Part 7:
EER-cores Part 8:
E-cores Part 9:
Planar cores Part 10:
PM-cores (under consideration, currently available as IEC 61247) Part 11:
EC-cores (under consideration, currently available as IEC 60647) Part 12: Uncoated ring cores (under consideration, currently available as IEC 61604) The committee has decided that the contents of the base publication and its amendments will remain unchanged until the maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in the data related to the specific publication. At this date, the publication will be
• reconfirmed, • withdrawn, • replaced by a revised edition, or • amended. A bilingual version of this publication may be issued at a later date.
62317-9 © IEC:2006+A1:2007(E) – 5 –
INTRODUCTION Nowadays, d.c.-d.c. converter power supplies increasingly employ transformers and chokes the windings of which are made of multi-layer printed circuit board or the windings are constructed in the motherboard, rather than the transformers wound by conventional copper wires. This part of IEC 62317 specifies the optimum shapes and dimensions of cores for SMD (Surface Mounted Device) and of cores for which the windings are constructed in the motherboard. The motherboard has slots cut out to accept the ferrite cores. This is called the total integration in a multi-layer motherboard. The core shape specified in this part of IEC 62317 satisfies the demand for lower profile as well as for smaller floor space.
– 6 – 62317-9 © IEC:2006+A1:2007(E) FERRITE CORES – DIMENSIONS –
Part 9: Planar cores
1 Scope This International Standard specifies the shapes and dimensions of ferrite cores for inductive components (transformers and chokes) of which the coil is typically constructed by multi-layer board or the coil is part of the motherboard. The general consideration upon which the design of this range of cores is based is given in Annex A. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60205, Calculation of the effective parameters of magnetic piece parts IEC 62317-4:2005, Ferrite cores – Dimensions – Part 4: RM cores and associated parts 3 Primary standard 3.1 Planar shape and dimensions The main shapes and dimensions shall be as given in the following figures and tables. The main shape, dimensions, and parameters for EL core are given in: Figure 1 – Planar core EL and mating PLT-core; Table 1 – Dimensions of planar core EL and the mating PLT-core; Table 2 – Effective parameter values and Amin values. The main shape, dimensions, and parameters for low-profile E-cores are given in: Figure 2 – Low-profile E-core and mating PLT-core; Table 3 – Dimensions of low-profile E-core and the mating PLT-core; Table 4 – Effective parameter values and Amin values. The main shape, dimensions, and parameters for ER-cores are given in:
Figure 3 – Low-profile ER-core;
Table 5 – Dimensions of low-profile ER-core;
Table 6 – Effective parameter values and Amin values. A uniform dimensional nomenclature has been chosen in order to facilitate a comparison of major physical attributes among the different core shapes.
62317-9 © IEC:2006+A1:2007(E) – 7 –
3.2 Dimensions of planar core EL and the mating PLT-core
R1 = F1/2 R2: 8 places B1 R1F1 A E D C F2 B2 C A IEC
581/06
Figure 1 – Planar core EL and the mating PLT-core Table 1 – Dimensions of planar core EL and the mating PLT-core Dimensions in millimetres Size A B1 B2 C D E F1 F2 R2 EL11 × 2,0
min.
max. 10,80 11,20 1,91 2,11
8,60 9,00 0,90 1,10 8,97 9,37 2,68 2,88 6,25 6,55 0,3
EL11 × 3,0
min.
max. 10,80 11,20 2,91 3,11
8,60 9,00 1,90 2,10 8,97 9,37 2,68 2,88 6,25 6,55 0,3 PLT11 × 1,0
min.
max. 10,80 11,20
0,96 1,06 8,60 9,00
EL13 × 2,2
min.
max. 12,75 13,25 2,09 2,29
10,20 10,60 0,90 1,10 10,63 11,03 3,19 3,39 7,41 7,71 0,3 EL13 × 3,2
min.
max. 12,75 13,25 3,09 3,29
10,20 10,60 1,90 2,10 10,63 11,03 3,19 3,39 7,41 7,71 0,3 PLT13 × 1,2
min.
max. 12,75 13,25
1,14 1,24 10,20 10,60
EL15,5 × 2,9
min.
max. 15,20 15,80 2,82 3,02
12,15 12,65 1,40 1,60 12,67 13,17 3,82 4,02 8,81 9,21 0,3 EL15,5 × 4,4
min.
max. 15,20 15,80 4,32 4,52
12,15 12,65 2,90 3,10 12,67 13,17 3,82 4,02 8,81 9,21 0,3 PLT15,5 × 1,4
min.
max. 15,20 15,80
1,32 1,52 12,15 12,65
EL18 × 3,7
min.
max. 17,70 18,30 3,55 3,75
14,15 14,65 1,90 2,10 14,70 15,30 4,45 4,65 10,27 10,67 0,3 EL18 × 5,7
min.
max.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.