SIST EN ISO 4210-8:2014
(Main)Cycles - Safety requirements for bicycles - Part 8: Pedal and drive system test methods (ISO 4210-8:2014)
Cycles - Safety requirements for bicycles - Part 8: Pedal and drive system test methods (ISO 4210-8:2014)
EN ISO 4210-8 specifies pedal and drive system test methods for ISO 4210-2.
Fahrräder - Sicherheitstechnische Anforderungen an Fahrräder - Teil 8: Prüfverfahren für Pedal und Antriebssystem (ISO 4210-8:2014)
Dieser Teil von ISO 4210 legt die Prüfverfahren für Pedal und Antriebssystem nach ISO 4210-2 fest.
Cycles - Exigences de sécurité des bicyclettes - Partie 8: Méthodes d'essai des pédales et du pédalier (ISO 4210-8:2014)
ISO 4210-8:2014 spécifie les méthodes d'essai des pédales et du système de transmission pour l'ISO 4210‑2.
Kolesa - Varnostne zahteve za kolesa - 8. del: Preskusne metode za pedala in gonilke (ISO 4210-8:2014)
Standard EN ISO 4210-8 določa preskusne metode za pedala in gonilke za standard ISO 4210-2.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 4210-8:2014
01-oktober-2014
1DGRPHãþD
SIST EN 14764:2006
SIST EN 14766:2006
SIST EN 14781:2006
Kolesa - Varnostne zahteve za kolesa - 8. del: Preskusne metode za pedala in
gonilke (ISO 4210-8:2014)
Cycles - Safety requirements for bicycles - Part 8: Pedal and drive system test methods
(ISO 4210-8:2014)
Fahrräder - Sicherheitstechnische Anforderungen an Fahrräder - Teil 8: Prüfverfahren für
Pedal und Antriebssystem (ISO 4210-8:2014)
Cycles - Exigences de sécurité des bicyclettes - Partie 8: Méthodes d'essai des pédales
et du pédalier (ISO 4210-8:2014)
Ta slovenski standard je istoveten z: EN ISO 4210-8:2014
ICS:
43.150 Kolesa Cycles
SIST EN ISO 4210-8:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 4210-8:2014
---------------------- Page: 2 ----------------------
SIST EN ISO 4210-8:2014
EUROPEAN STANDARD
EN ISO 4210-8
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2014
ICS 43.150 Supersedes EN 14764:2005, EN 14766:2005, EN
14781:2005
English Version
Cycles - Safety requirements for bicycles - Part 8: Pedal and
drive system test methods (ISO 4210-8:2014)
Cycles - Exigences de sécurité des bicyclettes - Partie 8: Fahrräder - Sicherheitstechnische Anforderungen an
Méthodes d'essai des pédales et du pédalier (ISO 4210- Fahrräder - Teil 8: Prüfverfahren für Pedal und
8:2014) Antriebssystem (ISO 4210-8:2014)
This European Standard was approved by CEN on 21 June 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 4210-8:2014 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 4210-8:2014
EN ISO 4210-8:2014 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 4210-8:2014
EN ISO 4210-8:2014 (E)
Foreword
This document (EN ISO 4210-8:2014) has been prepared by Technical Committee ISO/TC 149 "Cycles" in
collaboration with Technical Committee CEN/TC 333 “Cycles” the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2015, and conflicting national standards shall be withdrawn at
the latest by July 2015.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 14764:2005, EN 14766:2005, EN 14781:2005.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 4210-8:2014 has been approved by CEN as EN ISO 4210-8:2014 without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 4210-8:2014
---------------------- Page: 6 ----------------------
SIST EN ISO 4210-8:2014
INTERNATIONAL ISO
STANDARD 4210-8
First edition
2014-07-01
Cycles — Safety requirements for
bicycles —
Part 8:
Pedal and drive system test methods
Cycles — Exigences de sécurité des bicyclettes —
Partie 8: Méthodes d’essai des pédales et du pédalier
Reference number
ISO 4210-8:2014(E)
©
ISO 2014
---------------------- Page: 7 ----------------------
SIST EN ISO 4210-8:2014
ISO 4210-8:2014(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2014
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2014 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 4210-8:2014
ISO 4210-8:2014(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Test methods . 1
4.1 Pedal — Static strength test . 1
4.2 Pedal — Impact test . 2
4.3 Pedal — Dynamic durability test. 4
4.4 Drive system — Static strength test. 4
4.5 Drive belt — Tensile strength test . 5
4.6 Crank assembly — Fatigue test . 6
Bibliography . 9
© ISO 2014 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 4210-8:2014
ISO 4210-8:2014(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 149, Cycles, Subcommittee SC 1, Cycles and major
sub-assemblies.
This first edition of ISO 4210-8, together with ISO 4210-1, ISO 4210-2, ISO 4210-3, ISO 4210-4, ISO 4210-5,
ISO 4210-6, ISO 4210-7, and ISO 4210-9 cancels and replaces ISO 4210:1996, which has been technically
revised.
ISO 4210 consists of the following parts, under the general title Cycles — Safety requirements for bicycles:
— Part 1: Terms and definitions
— Part 2: Requirements for city and trekking, young adult, mountain and racing bicycles
— Part 3: Common test methods
— Part 4: Braking test methods
— Part 5: Steering test methods
— Part 6: Frame and fork test methods
— Part 7: Wheels and rims test methods
— Part 8: Pedals and drive system test methods
— Part 9: Saddles and seat-post test methods
iv
...
SLOVENSKI STANDARD
oSIST prEN ISO 4210-8:2013
01-januar-2013
Kolesa - Varnostne zahteve za kolesa - 8. del: Preskusne metode za pedala in
gonilke (ISO/DIS 4210-8:2012)
Cycles - Safety requirements for bicycles - Part 8: Pedals and crank test methods
(ISO/DIS 4210-8:2012)
Fahrräder - Sicherheitstechnische Anforderungen an Fahrräder - Teil 8: Prüfverfahren für
Pedal und Antriebssystem (ISO/DIS 4210-8:2012)
Cycles - Exigences de sécurité des bicyclettes - Partie 8: Méthodes d''essai des pédales
et du pédalier (ISO/DIS 4210-8:2012)
Ta slovenski standard je istoveten z: prEN ISO 4210-8
ICS:
43.150 Kolesa Cycles
oSIST prEN ISO 4210-8:2013 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 4210-8:2013
---------------------- Page: 2 ----------------------
oSIST prEN ISO 4210-8:2013
EUROPEAN STANDARD
DRAFT
prEN ISO 4210-8
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2012
ICS 43.150 Will supersede EN 14764:2005, EN 14766:2005, EN
14781:2005
English Version
Cycles - Safety requirements for bicycles - Part 8: Pedals and
crank test methods (ISO/DIS 4210-8:2012)
Cycles - Exigences de sécurité des bicyclettes - Partie 8: Fahrräder - Sicherheitstechnische Anforderungen an
Méthodes d''essai des pédales et du pédalier (ISO/DIS Fahrräder - Teil 8: Prüfverfahren für Pedal und
4210-8:2012) Antriebssystem (ISO/DIS 4210-8:2012)
This draft European Standard is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee
CEN/TC 333.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN ISO 4210-8:2012: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN ISO 4210-8:2013
prEN ISO 4210-8:2012 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
oSIST prEN ISO 4210-8:2013
prEN ISO 4210-8:2012 (E)
Foreword
This document (prEN ISO 4210-8:2012) has been prepared by Technical Committee ISO/TC 149 "Cycles" in
collaboration with Technical Committee CEN/TC 333 “Cycles” the secretariat of which is held by UNI.
This document is currently submitted to the parallel Enquiry.
This document will supersede EN 14764:2005, EN 14766:2005, EN 14781:2005.
Endorsement notice
The text of ISO/DIS 4210-8:2012 has been approved by CEN as a prEN ISO 4210-8:2012 without any
modification.
3
---------------------- Page: 5 ----------------------
oSIST prEN ISO 4210-8:2013
---------------------- Page: 6 ----------------------
oSIST prEN ISO 4210-8:2013
DRAFT INTERNATIONAL STANDARD ISO/DIS 4210-8
ISO/TC 149/SC 1 Secretariat: JISC
Voting begins on Voting terminates on
2012-11-08 2013-04-08
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMALISATION
Cycles — Safety requirements for bicycles —
Part 8:
Pedals and crank test methods
Cycles — Exigences de sécurité des bicyclettes —
Partie 8: Méthodes d''essai des pédales et du pédalier
ICS 43.150
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for Standardization (ISO), and
processed under the ISO-lead mode of collaboration as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member bodies for a parallel
five-month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments received, will be
submitted to a parallel two-month approval vote in ISO and formal vote in CEN.
To expedite distribution, this document is circulated as received from the committee
secretariat. ISO Central Secretariat work of editing and text composition will be undertaken at
publication stage.
Pour accélérer la distribution, le présent document est distribué tel qu'il est parvenu du
secrétariat du comité. Le travail de rédaction et de composition de texte sera effectué au
Secrétariat central de l'ISO au stade de publication.
THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE
REFERRED TO AS AN INTERNATIONAL STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT
INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION.
© International Organization for Standardization, 2012
---------------------- Page: 7 ----------------------
oSIST prEN ISO 4210-8:2013
ISO/DIS 4210-8
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user’s country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic,
photocopying, recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
ii © ISO 2012 – All rights reserved
---------------------- Page: 8 ----------------------
oSIST prEN ISO 4210-8:2013
ISO/DIS 4210-8
Contents Page
Foreword . iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Test methods . 1
4.1 Pedal – Static strength test . 1
4.2 Pedal – Impact test . 2
4.3 Pedal – Dynamic durability test . 3
4.4 Drive-system – Static strength test . 4
4.4.1 Test method for drive-system with chain . 4
4.4.2 Test method for drive-system with belt . 5
4.6 Crank assembly – Fatigue test . 5
4.6.1 General . 5
4.6.2 Test method with the cranks at 45° to the horizontal . 6
4.6.3 Test method with the cranks at 30° to the horizontal for mountain bicycles and racing
bicycles. 7
© ISO 2012 – All rights reserved iii
---------------------- Page: 9 ----------------------
oSIST prEN ISO 4210-8:2013
ISO/DIS 4210-8
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 4210-8 was prepared by Technical Committee ISO/TC 149, Cycles, Subcommittee SC 1, Cycles and
major sub-assemblies.
ISO 4210 consists of the following parts, under the general title Cycles — Safety requirements for bicycles:
Part 1: Terms and definitions
Part 2: Requirements for city & trekking, young adult, mountain and racing
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.