SIST EN 1555-1:2010
(Main)Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General
This part of EN 1555 specifies the general aspects of polyethylene (PE) piping systems in the field of the supply of gaseous fuels. It also specifies the test parameters for the test methods referred to in this standard. In conjunction with Parts 2 to 5 of EN 1555 it is applicable to PE pipes, fittings, and valves, their joints and to joints with components of other materials intended to be used under the following conditions: a) a maximum operating pressure, MOP, up to and including 10 bar 1) ; b) an operating temperature of 20 °C as reference temperature. EN 1555 (all parts) covers a range of maximum operating pressures and gives requirements concerning colours and additives.
Kunststoff-Rohrleitungssysteme für die Gasversorgung - Polyethylen (PE) - Teil 1: Allgemeines
Dieser Teil der EN 1555 legt allgemeine Anforderungen an Rohrleitungssysteme aus Polyethylen (PE) fest, die für die Gasversorgung eingesetzt werden. Er legt auch die Prüfparameter für die Prüfverfahren fest, auf die in dieser Norm verwiesen wird. In Verbindung mit den übrigen Teilen der EN 1555 (siehe Vorwort) gilt dieser Teil für Rohre, Formstücke und Armaturen aus PE, deren Verbindungen untereinander sowie mit Rohrleitungsteilen aus anderen Werkstoffen, die für die Verwendung unter den folgenden Bedingungen vorgesehen sind:
a) der maximal zulässige Betriebsdruck MOP beträgt höchstens 10 bar1).
b) es gilt eine Betriebstemperatur von 20 °C als Bezugstemperatur.
ANMERKUNG 1 Für andere Betriebstemperaturen sollten Minderungsfaktoren verwendet werden, siehe
prEN 1555-5:2008. EN 1555 enthält Festlegungen zu maximal zulässigen Betriebsdrücken und legt Anforderungen an die
Einfärbung von Rohrleitungsteilen sowie die Verwendung von Zusatzstoffen fest.
ANMERKUNG 2 Der Anwender bzw. Auftraggeber ist unter Berücksichtigung der eigenen Anforderungen sowie der
geltenden nationalen Festlegungen und Verlegepraktiken für die entsprechende Auswahl dieser Kriterien verantwortlich.
Systèmes de canalisations en plastique pour la distribution de combustibles gazeux - Polyéthylène (PE) - Partie 1: Généralités
La présente partie de l’EN 1555 spécifie les aspects généraux des systèmes de canalisations en polyéthylène (PE) dans le domaine de la distribution de combustibles gazeux.
Elle spécifie également les paramètres d'essai des méthodes d'essai auxquelles il est fait référence dans la présente norme. Conjointement avec les autres parties de l’EN 1555 (voir Avant-propos), elle s'applique aux tubes, raccords et robinets en PE et à leurs assemblages, ainsi qu'aux assemblages avec des composants en d'autres matières,
destinés à être utilisés dans les conditions suivantes :
a) une pression maximale de service, MOP, jusqu'à et y compris 10 bar1 ;
b) une température de service de 20 °C, comme température de référence.
NOTE 1 Pour d'autres températures de service, il convient d’utiliser des facteurs de réduction, voir le prEN 1555-5:2009.
L’EN 1555 couvre une gamme de pressions maximales de service et donne les exigences concernant les couleurs et les additifs.
NOTE 2 Il est de la responsabilité de l'acheteur ou du prescripteur de faire les choix appropriés de ces différents aspects, en tenant compte des exigences particulières et des règlements nationaux correspondants, ainsi que des pratiques ou des codes de pose.
Cevni sistemi iz polimernih materialov za oskrbo s plinastimi gorivi - Polietilen (PE) - 1. del: Splošno
Ta del EN 1555 določa splošne vidike cevnih sistemov iz polietilena (PE) na področju oskrbe s plinastimi gorivi. Določa tudi preskusne parametre za preskusne metode, navedene v tem standardu. Skupaj z 2. do 5. delom EN 1555 velja za PE cevi, fitinge in ventile, njihove spoje in spoje s komponentami iz drugih materialov, namenjenih za uporabo pod naslednjimi pogoji: a) najvišji obratovalni tlak MOP do in vključno z 10 bari; b) obratovalna temperatura 20 °C kot referenčna temperatura. EN 1555 (vsi deli) zajema razpon najvišjih obratovalnih tlakov in podaja zahteve glede barv in aditivov.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Cevni sistemi iz polimernih materialov za oskrbo s plinastimi gorivi - Polietilen (PE) - 1. del: SplošnoKunststoff-Rohrleitungssysteme für die Gasversorgung - Polyethylen (PE) - Teil 1: AllgemeinesSystèmes de canalisations en plastique pour la distribution de combustibles gazeux - Polyéthylène (PE) - Partie 1: GénéralitésPlastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General91.140.40Sistemi za oskrbo s plinomGas supply systems83.140.30Cevi, fitingi in ventili iz polimernih materialovPlastics pipes, fittings and valvesICS:Ta slovenski standard je istoveten z:EN 1555-1:2010SIST EN 1555-1:2010en,fr,de01-december-2010SIST EN 1555-1:2010SLOVENSKI
STANDARDSIST EN 1555-1:20031DGRPHãþD
SIST EN 1555-1:2010
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1555-1
September 2010 ICS 01.040.23; 01.040.91; 23.040.01; 91.140.40 Supersedes EN 1555-1:2002English Version
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 1: General
Systèmes de canalisations en plastique pour la distribution de combustibles gazeux - Polyéthylène (PE) - Partie 1 : Généralités
Kunststoff-Rohrleitungssysteme für die Gasversorgung - Polyethylen (PE) - Teil 1: Allgemeines This European Standard was approved by CEN on 30 July 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1555-1:2010: ESIST EN 1555-1:2010
EN 1555-1:2010 (E) 2 Contents Page Foreword . 3Introduction . 41 Scope . 52 Normative references . 53 Terms and definitions, symbols and abbreviations . 63.1 Terms and definitions . 63.1.1 Geometrical definitions . 73.1.2 Material definitions . 83.1.3 Definitions related to material characteristics . 93.1.4 Definitions related to service conditions . 103.1.5 Definitions related to joints . 103.2 Symbols . 103.3 Abbreviations . 114 Material . 114.1 Material of the components . 114.2 Compound . 114.2.1 Additives . 114.2.2 Colour . 114.2.3 Characteristics . 124.3 Fusion compatibility . 144.4 Classification and designation . 144.5 Design coefficient and design stress . 15Bibliography . 16 SIST EN 1555-1:2010
EN 1555-1:2010 (E) 3 Foreword This document (EN 1555-1:2010) has been prepared by Technical Committee CEN/TC 155 “Plastics piping and ducting systems”, the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by March 2011, and conflicting national standards shall be withdrawn at the latest by March 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1555-1:2002. It has been prepared in liaison with Technical Committee CEN/TC 234 "Gas infrastructure". System Standards are based on the results of the work being undertaken in ISO/TC 138 "Plastics pipes, fittings and valves for the transport of fluids", which is a Technical Committee of the International Organization for Standardization (ISO). They are supported by separate standards on test methods to which references are made throughout the System Standard. The System Standards are consistent with general standards on functional requirements and on recommended practice for installation. EN 1555 consists of the following parts:
EN 1555-1, Plastics piping systems for the supply of gaseous fuels Polyethylene (PE) Part 1: General (this standard); EN 1555-2, Plastics piping systems for the supply of gaseous fuels Polyethylene (PE) Part 2: Pipes; EN 1555-3, Plastics piping systems for the supply of gaseous fuels Polyethylene (PE) Part 3: Fittings; prEN 1555-4, Plastics piping systems for the supply of gaseous fuels Polyethylene (PE) Part 4: Valves; EN 1555-5, Plastics piping systems for the supply of gaseous fuels Polyethylene (PE) Part 5: Fitness for purpose of the system; CEN/TS 1555-7, Plastics piping systems for the supply of gaseous fuels Polyethylene (PE) Part 7: Guidance for assessment of conformity. NOTE EN 12007-2:2000 [1] prepared by CEN/TC 234 “Gas infrastructure” deals with the recommended practice for installation of plastics pipes system in accordance with EN 1555 (all parts). According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. SIST EN 1555-1:2010
EN 1555-1:2010 (E) 4 Introduction The System Standard, of which this is Part 1, specifies the requirements for a piping system and its components made from polyethylene (PE) and which is intended to be used for the supply of gaseous fuels. Requirements and test methods for components of the piping system are specified in EN 1555-2, EN 1555-3 and prEN 1555-4. Characteristics for fitness for purpose are covered in EN 1555-5 [6]. CEN/TS 1555-7 [2] gives guidance for assessment of conformity. Recommended practice for installation is given in EN 12007-2:2000 [1], prepared by CEN/TC 234. This part of EN 1555 covers the general aspects of the plastics piping system. SIST EN 1555-1:2010
EN 1555-1:2010 (E) 5 1 Scope This part of EN 1555 specifies the general aspects of polyethylene (PE) piping systems in the field of the supply of gaseous fuels. It also specifies the test parameters for the test methods referred to in this standard. In conjunction with Parts 2 to 5 of EN 1555 it is applicable to PE pipes, fittings, and valves, their joints and to joints with components of other materials intended to be used under the following conditions: a) a maximum operating pressure, MOP, up to and including 10 bar 1); b) an operating temperature of 20 °C as reference temperature. NOTE 1 For other operating temperatures, derating coefficients should be used, see EN 1555-5 [6]. EN 1555 (all parts) covers a range of maximum operating pressures and gives requirements concerning colours and additives. NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1555-2:2010, Plastics piping systems for the supply of gaseous fuels — Polyethylene (PE) — Part 2: Pipes EN 1555-3, Plastics piping systems for the supply of gaseous fuels — Polyethylene (PE) — Part 3: Fittings prEN 1555-4, Plastics piping systems for the supply of gaseous fuels — Polyethylene (PE) — Part 4: Valves EN 12099, Plastics piping systems — Polyethylene piping materials and components — Determination of volatile content EN ISO 472:2001, Plastics — Vocabulary (ISO 472:1999) EN ISO 1043-1:2001, Plastics
Symbols and abbreviated terms
Part 1: Basic polymers and their special characteristics (ISO 1043-1:2001) EN ISO 1133, Plastics
Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005) EN ISO 1167-1:2006, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 1: General method (ISO 1167-1:2006) EN ISO 1167-2, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces (ISO 1167-2:2006) EN ISO 1183-1, Plastics
Methods for determining the density of non-cellular plastics
Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2004)
1) 1 bar = 0,1 MPa. SIST EN 1555-1:2010
EN 1555-1:2010 (E) 6 EN ISO 1183-2, Plastics
Methods for determining the density of non-cellular plastics
Part 2: Density gradient column method (ISO 1183-2:2004) EN ISO 6259-1, Thermoplastics pipes
Determination of tensile properties
Part 1: General test method (ISO 6259-1:1997) prEN ISO 9080, Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation (ISO/DIS 9080:2010) EN ISO 12162, Thermoplastics materials for pipes and fittings for pressure applications — Classification, designation and design coefficient (ISO 12162:2009) EN ISO 13477, Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test) (ISO 13477:2008) EN ISO 13478, Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Full-scale test (FST) (ISO 13478:2007) EN ISO 13479, Polyolefin pipes for the conveyance of fluids — Determination of resistance to crack propagation — Test method for slow crack growth on notched pipes (ISO 13479:2009) EN ISO 15512, Plastics
Determination of water content (ISO 15512:2008) EN ISO 16871, Plastics piping and ducting systems
Plastics pipes and fittings
Method for exposure to direct (natural) weathering (ISO 16871:2003) ISO 6259-3, Thermoplastics pipes — Determination of tensile properties — Part 3: Polyolefin pipes ISO 6964, Polyolefin pipes and fittings — Determination of carbon black content by calcination and pyrolysis — Test method and basic specification ISO 11357-6, Plastics — Differential scanning calorimetry (DSC) — Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) ISO 11413:2008, Plastics pipes and fittings
Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting ISO 11414:2009, Plastics pipes and fittings
Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion ISO 13953, Polyethylene (PE) pipes and fittings
Determination of the tensile strength and failure mode of test pieces from a butt-fused joint ISO 13954, Plastics pipes and fittings
Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm ISO 18553, Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds 3 Terms and definitions, symbols and abbreviations 3.1 Terms and definitions For the purposes of this document, the terms and definitions given in EN ISO 472:2001 and
EN ISO 1043-1:2001 and the following apply. SIST EN 1555-1:2010
EN 1555-1:2010 (E) 7 3.1.1 Geometrical definitions 3.1.1.1 nominal size DN/OD numerical designation of the size of a component, other than a component designated by thread size, which is a convenient round number, approximately equal to the manufacturing dimension in millimetres (mm) and related to the outside diameter 3.1.1.2 nominal outside diameter dn specified outside diameter, in millimetres, assigned to a nominal size DN/OD 3.1.1.3 outside diameter at any point de value of the measurement of the outside diameter through its cross-section at any point of the pipe, rounded to the next greater 0,1 mm 3.1.1.4 mean outside diameter dem value of the measurement of the outer circumference of the pipe or spigot end of a fitting in any cross-section divided by
(= 3,142), rounded to the next greater 0,1 mm 3.1.1.5 minimum mean outside diameter dem,min minimum value for the mean outside diameter as specified for a given nominal size 3.1.1.6 maximum mean outside diameter dem,max maximum value for the mean outside diameter as specified for a given nominal size 3.1.1.7 out-of-roundness
ovality difference between the maximum and the minimum outside diameter in the same cross-section of a pipe or spigot 3.1.1.8 nominal wall thickness en numerical designation of the wall thickness of a component, which is a convenient round number, approximately equal to the manufacturing dimension in millimetres (mm) NOTE For thermoplastics components conforming to the different parts of EN 1555, the value of the nominal wall thickness, en, is identical to the specified minimum wall thickness at any point, emin. 3.1.1.9 wall thickness at any point e wall thickness at any point around the circumference of a component rounded to the next greater 0,1 mm NOTE The symbol for the wall thickness of the fittings and valves body at any point is E. SIST EN 1555-1:2010
EN 1555-1:2010 (E) 8 3.1.1.10 minimum wall thickness at any point emin minimum value for the wall thickness at any point around the circumference of a component,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.