SIST EN 60728-1-2:2009

Cable networks for television signals, sound signals and interactive services - Part 1-2: Performance requirements for signals delivered at the system outlet in operation (IEC 60728-1-2:2009)

This part of IEC 60728 provides the minimum performance requirements to be fulfilled in operation at the system outlet or terminal input and describes the summation criteria for the impairments present in the received signals and those produced by the CATV/MATV/SMATV cable network, including individual receiving systems. In a building divided into apartment blocks, the signals received by the antennas are distributed by the MATV/SMATV cable network up to the home network interface (HNI); the television signals are then distributed (inside the home) by home networks (HN) of various types up to the system outlet or terminal input. The cable network can support two way operation, from the system outlet (or terminal input) towards the headend. The home network can use coaxial cables, balanced pair cables, fibre optic cables (glass or plastic) and also wireless links inside a room (or a small number of adjacent rooms) to replace wired cords. This part of IEC 60728 is applicable to cable networks intended for television signals, sound signals and interactive services operating between about 5 MHz and 3 000 MHz. The frequency range is extended to 6 000 MHz for home distribution techniques that replace wired cords with a wireless two way communication inside a room (or a small number of adjacent rooms) that uses the 5 GHz to 6 GHz frequency band. 64H64H64H58HFigure 1 shows the main sections of a general CATV/MATV/SMATV system, indicating the parts of the IEC 60728-1 series documents where the relevant performance requirements are indicated. - The requirements for the signals received at the headend are given in Clause 6 of IEC 60728-1. - The requirements for the CATV/MATV/SMATV cable network, assuming an unimpaired input signal at the input of the headend, up to the system outlet are given in IEC 60728-1, Clause 5. - The requirements for the CATV/MATV/SMATV cable network up to the home network interface (HNI) are given in IEC 60728-1, Clause 7, assuming an unimpaired input signal at the input of the headend. - The specific requirements from HNI to the system outlet or terminal input are given in IEC 60728-1-1, Clause 5, assuming an unimpaired input signal at the HNI. - The requirements at the system outlet in operation are given in Clause 7 of this standard. The expression "in operation" means that the received signals, with their impairments, are applied to the headend input of the CATV/MATV/SMATV cable network. The requirements at the system outlet "in operation" are derived, therefore, by summing the impairments of the various cascaded parts of the system and of the input signal.

Kabelnetze für Fernsehsignale, Tonsignale und interaktive Dienste - Teil 1-2: Leistungsanforderungen an Signale der Teilnehmeranschlussdose im realen Betrieb (IEC 60728-1-2:2009)

Réseaux de distribution par câbles pour signaux de télévision, signaux de radiodiffusion sonore et services interactifs - Partie 1-2: Exigences de performance relatives aux signaux délivrés à la prise terminale en fonctionnement (CEI 60728-1-2:2009)

Kabelska omrežja za televizijske in zvokovne signale ter interaktivne storitve - 1-2. del: Tehnične zahteve za signale na izhodu delujočega sistema (IEC 60728-1-2:2009)

General Information

• Status: Withdrawn
• Publication Date: 08-Oct-2009
• Withdrawal Date: 06-Nov-2016
• ICS: 33.060.40 - Cabled distribution systems
• Technical Committee: AVM - Audio, video and multimedia systems and equipment
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 04-Nov-2016
• Due Date: 27-Nov-2016
• Completion Date: 07-Nov-2016
• Ref Project: EN 60728-1-2:2009 - Cable networks for television signals, sound signals and interactive services - Part 1-2: Performance requirements for signals delivered at the system outlet in operation

Relations

• Replaced By: SIST EN 60728-1:2014 - Cable networks for television signals, sound signals and interactive services -- Part 1: System performance of forward paths (IEC 60728-1:2014)
• Effective Date: 16-Oct-2012
• Replaced By: SIST EN 60728-1-2:2014 - Cable networks for television signals, sound signals and interactive services - Part 1-2: Performance requirements for signals delivered at the system outlet in Operation (IEC 60728-1-2:2014)
• Effective Date: 16-Oct-2012
• Replaced By: SIST EN 60728-1-2:2014 - Cable networks for television signals, sound signals and interactive services - Part 1-2: Performance requirements for signals delivered at the system outlet in Operation (IEC 60728-1-2:2014)
• Effective Date: 29-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 60728-1-2:2009
01-november-2009
.DEHOVNDRPUHåMD]DWHOHYL]LMVNHLQ]YRNRYQHVLJQDOHWHULQWHUDNWLYQHVWRULWYH
GHO7HKQLþQH]DKWHYH]DVLJQDOHQDL]KRGXGHOXMRþHJDVLVWHPD,(&

Cable networks for television signals, sound signals and interactive services - Part 1-2:
Performance requirements for signals delivered at the system outlet in operation (IEC
60728-1-2:2009)
Kabelnetze für Fernsehsignale, Tonsignale und interaktive Dienste - Teil 1-2:
Leistungsanforderungen an Signale der Teilnehmeranschlussdose im realen Betrieb
(IEC 60728-1-2:2009)
Réseaux de distribution par câbles pour signaux de télévision, signaux de radiodiffusion
sonore et services interactifs - Partie 1-2: Exigences de performance relatives aux
signaux délivrés à la prise terminale en fonctionnement (CEI 60728-1-2:2009)
Ta slovenski standard je istoveten z: EN 60728-1-2:2009
ICS:
33.060.40 Kabelski razdelilni sistemi Cabled distribution systems
SIST EN 60728-1-2:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60728-1-2:2009

---------------------- Page: 2 ----------------------

SIST EN 60728-1-2:2009

EUROPEAN STANDARD
EN 60728-1-2

NORME EUROPÉENNE
September 2009
EUROPÄISCHE NORM

ICS 33.160; 35.110; 33.120.10


English version


Cable networks for television signals,
sound signals and interactive services -
Part 1-2: Performance requirements
for signals delivered at the system outlet in operation
(IEC 60728-1-2:2009)


Réseaux de distribution par câbles  Kabelnetze für Fernsehsignale,
pour signaux de télévision, Tonsignale und interaktive Dienste -
signaux de radiodiffusion sonore Teil 1-2: Leistungsanforderungen
et services interactifs - an Signale der Teilnehmeranschlussdose
Partie 1-2: Exigences de performance im realen Betrieb
relatives aux signaux délivrés (IEC 60728-1-2:2009)
à la prise terminale en fonctionnement
(CEI 60728-1-2:2009)




This European Standard was approved by CENELEC on 2009-07-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Central Secretariat: Avenue Marnix 17, B - 1000 Brussels


© 2009 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 60728-1-2:2009 E

---------------------- Page: 3 ----------------------

SIST EN 60728-1-2:2009
EN 60728-1-2:2009 - 2 -
Foreword
The text of document 100/1531/FDIS, future edition 1 of IEC 60728-1-2, prepared by technical area 5:
Cable networks for television signals, sound signals and interactive services, of IEC TC 100, Audio, video
and multimedia systems and equipment, was submitted to the IEC-CENELEC parallel vote and was
approved by CENELEC as EN 60728-1-2 on 2009-07-01.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
(dop) 2010-04-01
national standard or by endorsement
– latest date by which the national standards conflicting
(dow) 2012-07-01
with the EN have to be withdrawn
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 60728-1-2:2009 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following note has to be added for the standard indicated:
IEC 60728-10 NOTE  Harmonized as EN 60728-10:2006 (not modified).
__________

---------------------- Page: 4 ----------------------

SIST EN 60728-1-2:2009
- 3 - EN 60728-1-2:2009

Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

1)
IEC 60050-705 - International Electrotechnical Vocabulary - -
(IEV) -
Chapter 705: Radio wave propagation


1)
IEC 60050-712 - International Electrotechnical Vocabulary - -
(IEV) -
Chapter 712: Antennas


1)
IEC 60050-725 - International Electrotechnical Vocabulary - -
(IEV) -
Chapter 725: Space radiocommunications


IEC 60728-1 2007 Cable networks for television signals, sound EN 60728-1 2008
signals and interactive services -
Part 1: System performance of forward paths


2) 2)
IEC 60728-1-1 - Cable networks for television signals, sound EN 60728-1-1 -
signals and interactive services -
Part 1-1: RF cabling for two way home
networks


1) 3)
IEC 60728-3 - Cable networks for television signals, sound EN 60728-3 2006
signals and interactive services -
Part 3: Active wideband equipment for coaxial
cable networks


1) 3)
IEC 60966-2-4 - Radio frequency and coaxial cable EN 60966-2-4 2009
assemblies -
Part 2-4: Detail specification for cable
assemblies for radio and TV receivers -
Frequency range 0 MHz to 3 000 MHz,
IEC 61169-2 connectors


1) 3)
IEC 60966-2-5 - Radio frequency and coaxial cable EN 60966-2-5 2009
assemblies -
Part 2-5: Detail specification for cable
assemblies for radio and TV receivers -
Frequency range 0 MHz to 1 000 MHz,
IEC 61169-2 connectors


1) 3)
IEC 60966-2-6 - Radio frequency and coaxial cable EN 60966-2-6 2009
assemblies -
Part 2-6: Detail specification for cable
assemblies for radio and TV receivers -
Frequency range 0 MHz to 3 000 MHz,
IEC 61169-24 connectors



1)
Undated reference.
2)
At draft stage.
3)
Valid edition at date of issue

---------------------- Page: 5 ----------------------

SIST EN 60728-1-2:2009
EN 60728-1-2:2009 - 4 -
Publication Year Title EN/HD Year

1)
ITU-R - Methodology for the subjective assessment - -
Recommendation of the quality of television pictures
BT.500-7


1)
ITU-R - Subjective quality of television pictures in - -
Recommendation relation to the main impairments of the
B.654 analogue composite television signal


1)
ITU-R - Radio-frequency protection ratios for AM - -
Recommendation vestigial sideband terrestrial television
B.655 systems interfered with by unwanted analogue
vision signals and their associated sound
signals


1)
ITU-T - Transmission performance of television - -
Recommendation circuits designed for use in international
J.61 connections


1)
ITU-T - Insertion of test signals in the field-blanking - -
Recommendation interval of monochrome and colour television
J.63 signals


1)
- - Digital Video Broadcasting (DVB); Framing ETSI EN 300 421 -
structure, channel coding and modulation for
11/12 GHz satellite services


1)
- - Digital Video Broadcasting (DVB); Framing ETSI EN 300 429 -
structure, channel coding and modulation for
cable systems


1)
- - Digital Video Broadcasting (DVB); Satellite ETSI EN 300 473 -
Master Antenna Television (SMATV)
distribution systems


1)
- - Digital Video Broadcasting (DVB); Framing ETSI EN 300 744 -
structure, channel coding and modulation for
digital terrestrial television


1)
- - Digital Video Broadcasting (DVB); Second ETSI EN 302 307 -
generation framing structure, channel coding
and modulation systems for Broadcasting,
Interactive Services, News Gathering and
other broadband satellite applications

---------------------- Page: 6 ----------------------

SIST EN 60728-1-2:2009
IEC 60728-1-2
®
Edition 1.0 2009-06
INTERNATIONAL
STANDARD


Cable networks for television signals, sound signals and interactive services –
Part 1-2: Performance requirements for signals delivered at the system outlet in
operation


INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
V
ICS 33.160 35.110; 33.120.10 ISBN 2-8318-1048-0
® Registered trademark of the International Electrotechnical Commission

---------------------- Page: 7 ----------------------

SIST EN 60728-1-2:2009
– 2 – 60728-1-2 © IEC:2009(E)
CONTENTS
FOREWORD.4
INTRODUCTION.6
1 Scope.7
2 Normative references .8
3 Terms, definitions, symbols and abbreviations.10
3.1 Terms and definitions .10
3.2 Abbreviations .15
4 Methods of measurement .16
5 Subjective quality of television pictures in relation to the main impairments of the
analogue composite television signal.17
5.1 Subjective quality scale .17
5.2 Subjective quality and objective parameters .17
6 Summation of the impairments .20
6.1 Impairments to be summed .20
6.2 Summation laws .21
6.2.1 General .21
6.2.2 Voltage addition .21
6.2.3 Power addition.22
6.3 Examples .22
7 Performance requirements in operation .22
7.1 General .22
7.2 Impedance .23
7.3 Performance requirements at the terminal input .23
7.3.1 Definition.23
7.3.2 Signal level.23
7.3.3 Other parameters .23
7.4 Performance requirements at system outlets .23
7.4.1 Minimum and maximum carrier levels .23
7.4.2 Mutual isolation between system outlets .23
7.4.3 Isolation between individual outlets in one household .24
7.4.4 Isolation between forward and return path .24
7.4.5 Long-term frequency stability of distributed carrier signals at any
system outlet .24
7.4.6 Carrier level differences at system outlet .24
7.4.7 Frequency response within a television channel .24
7.4.8 Random noise at system outlet.24
7.4.9 Interference to television channels .26
Annex A (normative) RF carrier to noise ratio .28
Annex B (informative) Examples of summation of impairments.31
Bibliography.33

Figure 1 – CATV/MATV/SMATV cable network – Performance requirements .8
Figure 2 – Examples of location of HNI for various home network types.13
Figure 3 – Signal to echo ratio (dB) versus echo delay (μs) .20
Figure A.1 – Example of a TV receiver IF filter (systems B and G) .28

---------------------- Page: 8 ----------------------

SIST EN 60728-1-2:2009
60728-1-2 © IEC:2009(E) – 3 –
Figure A.2 – Example of a demodulated TV signal (systems B and G) .29

Table 1 – Methods of measurement of IEC 60728-1 applicable in operation.17
Table 2 – Impairment units versus subjective quality.17
Table 3 – Impairment grade versus un-weighted white noise .18
Table 4 – Impairment grade versus differential gain .19
Table 5 – Impairment grade versus differential phase .19
Table 6 – Impairment grade versus short time linear distortion (2T pulse).19
Table 7 – Impairment grade versus chrominance-luminance gain inequality.19
Table 8 – Impairment grade versus chrominance-luminance delay inequality .19
Table 9 – Impairment grade versus echo rating (1μs echo delay).20
Table 10 – Correction factors to be applied for delays different than 1 μs .20
Table 11 – Carrier-to-noise ratios and RF signal-to-noise ratios at system outlet
(television) in operation .25
Table 12 – Carrier-to-noise ratios at system outlet (radio) in operation .26
Table B.1 – Examples of voltage addition .31
Table B.2 – Examples of power addition .32

---------------------- Page: 9 ----------------------

SIST EN 60728-1-2:2009
– 4 – 60728-1-2 © IEC:2009(E)
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

CABLE NETWORKS FOR TELEVISION SIGNALS,
SOUND SIGNALS AND INTERACTIVE SERVICES –

Part 1-2: Performance requirements for signals
delivered at the system outlet in operation


FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60728-1-2 has been prepared by technical area 5: Cable networks
for television signals, sound signals and interactive services, of IEC technical committee 100:
Audio, video and multimedia systems and equipment.
The text of this standard is based on the following documents:
FDIS Report on voting
100/1531/FDIS 100/1562/RVD

Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
A list of all parts of the IEC 60728 series, published under the general title Cable networks for
television signals, sound signals and interactive services, can be found on the IEC website.

---------------------- Page: 10 ----------------------

SIST EN 60728-1-2:2009
60728-1-2 © IEC:2009(E) – 5 –
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
The committee has decided that the contents of this publication will remain unchanged until
the maintenance result date00F indicated on the IEC web site under "http://webstore.iec.ch" in
the data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.

---------------------- Page: 11 ----------------------

SIST EN 60728-1-2:2009
– 6 – 60728-1-2 © IEC:2009(E)
INTRODUCTION
Standards of the IEC 60728 series deal with cable networks including equipment and
associated methods of measurement for headend reception, processing and distribution of
television signals, sound signals and their associated data signals, and for processing, interfacing
and transmitting all kinds of signals for interactive services using all applicable transmission media.
This includes
1
• CATV 1F1F1F0F -networks,
• MATV-networks and SMATV-networks,
• individual receiving networks
and all kinds of equipment, systems and installations installed in such networks.
The extent of this standardization work is from the antennas and/or special signal source
inputs to the headend or other interface points to the network up to the terminal input.
The standardization of any user terminals (i.e. tuners, receivers, decoders, multimedia
terminals, etc.) as well as of any coaxial, balanced and optical cables and accessories thereof
is excluded.
The reception of television signals inside a building requires an outdoor antenna and a
distribution network to convey the signal to the TV receivers.
This part of IEC 60728 deals with the requirements that must be fulfilled at the system outlet
or terminal input, when the CATV/MATV/SMATV system is in operation.
These performance requirements for signals at the system outlet or terminal input in operation
are derived from considerations of the characteristics of the received signals at the input of
the headend (see Clause 6 of IEC 60728-1) and the summation of the impairments produced
by the headend, the CATV/MATV/SMATV network and the home network, when the
requirements given in IEC 60728-1 and IEC 60728-1-1 are fulfilled.
This document gives the guidelines for calculation of the operational characteristics at system
outlet, taking into account the performance requirements of the CATV/MATV/SMATV network,
of the home networks and of the received signals, given in the International Standards
IEC 60728-1 and 60728-1-1 prepared by TA 5: Cable networks for television signals, sound
signals and interactive services, of IEC technical committee 100: Audio, video and multimedia
systems and equipment.


—————————
1
 This word encompasses the Hybrid Fibre Coaxial (HFC) networks used nowadays to provide telecommunications
services, voice, data, audio and video both broadcast and narrowcast.

---------------------- Page: 12 ----------------------

SIST EN 60728-1-2:2009
60728-1-2 © IEC:2009(E) – 7 –
CABLE NETWORKS FOR TELEVISION SIGNALS,
SOUND SIGNALS AND INTERACTIVE SERVICES –

Part 1-2: Performance requirements for signals
delivered at the system outlet in operation



1 Scope
This part of IEC 60728 provides the minimum performance requirements to be fulfilled in
operation at the system outlet or terminal input and describes the summation criteria for the
impairments present in the received signals and those produced by the CATV/MATV/SMATV
cable network, including individual receiving systems.
NOTE 1 When a change of signal format is made at the headend, the summation of the impairments does not
apply (see also Clause 57H 7).
In a building divided into apartment blocks, the signals received by the antennas are
distributed by the MATV/SMATV cable network up to the home network interface (HNI); the
television signals are then distributed (inside the home) by home networks (HN) of various
types up to the system outlet or terminal input. The cable network can support two way
operation, from the system outlet (or terminal input) towards the headend.
The home network can use coaxial cables, balanced pair cables, fibre optic cables (glass or
plastic) and also wireless links inside a room (or a small number of adjacent rooms) to replace
wired cords.
This part of IEC 60728 is applicable to cable networks intended for television signals, sound
signals and interactive services operating between about 5 MHz and 3 000 MHz. The
frequency range is extended to 6 000 MHz for home distribution techniques that replace wired
cords with a wireless two way communication inside a room (or a small number of adjacent
rooms) that uses the 5 GHz to 6 GHz frequency band.
64H64H64H58HFigure 1 shows the main sections of a general CATV/MATV/SMATV system, indicating the
parts of the IEC 60728-1 series documents where the relevant performance requirements are
indicated.
• The requirements for the signals received at the headend are given in Clause 6 of
IEC 60728-1.
• The requirements for the CATV/MATV/SMATV cable network, assuming an unimpaired
input signal at the input of the headend, up to the system outlet are given in IEC 60728-1,
Clause 5.
• The requirements for the CATV/MATV/SMATV cable network up to the home network
interface (HNI) are given in IEC 60728-1, Clause 7, assuming an unimpaired input signal
at the input of the headend.
• The specific requirements from HNI to the system outlet or terminal input are given in
IEC 60728-1-1, Clause 5, assuming an unimpaired input signal at the HNI.
• The requirements at the system outlet in operation are given in Clause 7 of this standard.
The expression “in operation” means that the received signals, with their impairments, are
applied to the headend input of the CATV/MATV/SMATV cable network. The requirements at
the system outlet “in operation” are derived, therefore, by summing the impairments of the
various cascaded parts of the system and of the input signal.

---------------------- Page: 13 ----------------------

SIST EN 60728-1-2:2009
– 8 – 60728-1-2 © IEC:2009(E)
When a change of signal format from analogue to analogue (e.g. from FM to AM-VSB) or from
digital to digital (e.g. from QPSK to QAM) or from digital to analogue (e.g. from DVB-S/S2 to
AM-VSB or DVB-T to AM-VSB) is made at the headend, the summation of the impairments
that produce a relaxation of requirements at system outlet does not apply. Such a case will be
the equivalence of unimpaired signals applied at the headend input. Therefore the
requirements at system outlet given in IEC 60728-1 apply.

Performance requirements,
see Clause 7 (in operation)
Antenna system
(or other feeding network)
Satellite
Terrestrial
antenna
antenna
HNI
CATV/MATV/SMATV
Distribution Home network Terminal
Headend
network (HN) equipment
System
oulet
Headend
input
Performance requirements,
see Clause 5 of IEC 60728-1-1
Performance requirements, see Clause 7
(unimpaired input signals)
of IEC 60728-1 (unimpaired input signals)
Performance
requirements,
see Clause 6
Performance requirements, see Clause 5
of IEC 60728-1
of IEC 60728-1 (unimpaired input signals)
IEC  1012/09

Diagram of the main sections of a CATV/MATV/SMATV cable network and the relevant parts
of the IEC 60728-1 series where the requirements are indicated.
Figure 1 – CATV/MATV/SMATV cable network – Performance requirements
This standard also provides references for the basic methods of measurement of the
operational characteristics of the downstream cable network in order to assess its
performance.
All requirements refer to the performance limits to be achieved in operation at any system
outlet when terminated in a resistance equal to the nominal load impedance of the system,
unless otherwise specified. Where system outlets are not used, the above applies to the
terminal input.
NOTE 2 If the home network is subdivided into a number of parts, using different transmission media (e.g. coaxial
cabling, balanced cabling, optical cabling, wireless links) the accumulation of degradations should not exceed the
figures given below.
NOTE 3 Performance requirements of return paths as well as special methods of measurement for the use of the
return paths in cable networks are described in IEC 60728-10.
2 Normative references
The following referenced documents are indispensable for the application of this document.
For dated references, only the edition cited applies. For undated references, the latest edition
of the referenced document (including any amendments) applies.
IEC 60050-705, International Electrotechnical Vocabulary (IEV) – Chapter 705: Radio wave
propagation

---------------------- Page: 14 ----------------------

SIST EN 60728-1-2:2009
60728-1-2 © IEC:2009(E) – 9 –
IEC 60050-712, International Electrotechnical Vocabulary (IEV) – Chapter 712: Antennas
IEC 60050-725, International Electrotechnical Vocabulary (IEV) – Chapter 725: Space
radiocommunications
IEC 60728-1:2007, Cable networks for television signals, sound signals and interactive
services – Part 1: System performance of forward paths
IEC 60
...