SIST EN 301 908-13 V11.1.1:2016

IMT cellular networks - Harmonised Standard covering the essential requirements of article 3.2 of the Radio Equipment Directive 2014/53/EU - Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)

The present document covers requirements for E-UTRA FDD and E-UTRA TDD User Equipment from 3GPP™
Releases 8, 9, 10 and 11 defined in ETSI TS 136 101 [3]. This includes the requirements for E-UTRA UE operating
bands and E-UTRA CA operating bands from 3GPP™ Release 12 defined in ETSI TS 136 101 [i.13].
NOTE: For Band 20:
􀀀 For user equipment designed to be mobile or nomadic, the requirements in the present document
measured at the antenna port also show conformity to the corresponding requirement defined as
TRP (total radiated power), as described in Commission Decision 2010/267/EU [i.6], ECC
Decision (09)03 [i.7] and CEPT Report 30 [i.8].
􀀀 For user equipment designed to be fixed or installed, the present document does not address the
requirements described in Commission Decision 2010/267/EU [i.6], ECC Decision (09)03 [i.7] and
CEPT Report 30 [i.8].
The present document contains requirements to demonstrate that radio equipment both effectively uses and supports the
efficient use of radio spectrum in order to avoid harmful interference.

Celična omrežja IMT - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive za radijsko opremo 2014/53/EU - 13. del: Uporabniška oprema za razviti prizemni radijski dostop za UMTS (E-UTRA)

Ta dokument zajema zahteve za uporabniško opremo E-UTRA FDD in E-UTRA TDD iz izdaj 8, 9, 10 ter 11 dokumenta 3GPP™, kot je določeno v dokumentu ETSI TS 136 101 [3]. To vključuje zahteve za pasove, v katerih deluje E-UTRA UE, in pasove, v katerih deluje E-UTRA CA, iz izdaje 12 dokumenta 3GPP™, kot je določeno v dokumentu ETSI TS 136 101 [i.13].
OPOMBA: Za pas 20:
􀀀 Za uporabniško opremo, zasnovano kot mobilno ali nomadsko, so zahteve iz tega dokumenta, izmerjene na antenskem vhodu, tudi v skladu z ustrezno zahtevo, opredeljeno kot TRP (skupna sevana moč), kot je opisana v Sklepu Komisije 2010/267/EU [i.6], Sklepu Odbora za elektronske komunikacije (09)03 [i.7] in poročilu CEPT 30 [i.8].
􀀀 Za uporabniško opremo, zasnovano za priključitev ali namestitev, ta dokument ne obravnava zahtev,
opisanih v Sklepu Komisije 2010/267/EU [i.6], Sklepu Odbora za elektronske komunikacije (09)03 [i.7] in
poročilu CEPT 30 [i.8].
Ta dokument vsebuje zahteve, s katerimi se dokazuje, da radijska oprema učinkovito uporablja radijski spekter in tudi podpira njegovo učinkovito uporabo, tako da ne pride do škodljivih motenj.

General Information

• Status: Published
• Public Enquiry End Date: 07-Feb-2016
• Publication Date: 17-Aug-2016
• ICS: 33.060.99 - Other equipment for radiocommunications
• ICS: 33.070.99 - Other mobile services
• Technical Committee: MOC - Mobile Communications
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Aug-2016
• Due Date: 06-Oct-2016
• Completion Date: 18-Aug-2016
• Directive: 1999/5/EC - Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity
• Directive: 2014/53/EU - Directive 2014/53/EU of The European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC
• Mandate: M/284
• Ref Project: ETSI EN 301 908-13 V11.1.1 (2016-07) - IMT cellular networks; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)

Overview

SIST EN 301 908-13 V11.1.1:2016 is a harmonised European standard for IMT cellular networks that implements the essential requirements of Article 3.2 of the Radio Equipment Directive (RED 2014/53/EU) for Evolved Universal Terrestrial Radio Access (E-UTRA / LTE) User Equipment (UE). The document applies to E-UTRA FDD and TDD UE defined in 3GPP Releases 8–11 and includes requirements for E-UTRA and Carrier Aggregation (CA) operating bands introduced in 3GPP Release 12. It defines the RF and regulatory requirements needed to demonstrate efficient use of radio spectrum and to avoid harmful interference, supporting CE marking and market access in the EU.

Key Topics and Technical Requirements

The standard contains detailed technical and conformance specifications for LTE / E-UTRA UE, including:

• Transmitter requirements

  • Maximum and minimum output power (single-carrier and multi-carrier/CA scenarios)
  • Transmitter Spectrum Emission Mask (SEMs) for single carrier, intra-band contiguous CA, UL‑MIMO, and multi-cluster PUSCH
  • Transmitter spurious emissions and conformance procedures

• Receiver requirements

  • Adjacent Channel Selectivity (ACS)
  • Blocking characteristics and spurious response
  • Intermodulation performance for single-carrier and CA scenarios

• Conformance framework

  • Environmental profile and test conditions
  • Measurement and reporting requirements to demonstrate compliance with RED Article 3.2

• Band-specific notes

  • Special conformity notes for Band 20 distinguishing mobile/nomadic UE (antenna port measurement demonstrating TRP equivalence) and fixed/installed UE (requirements not covered by the Band 20 TRP decisions).

Practical Applications and Who Uses This Standard

This harmonised standard is essential for stakeholders involved in the design, testing, certification and deployment of LTE / E-UTRA user equipment:

• Device manufacturers and RF/antenna engineers - to design UE that meet EU regulatory RF limits and spectrum efficiency requirements.
• Test laboratories and conformity assessment bodies - to perform RF performance, SEM, spurious emissions and receiver tests required for CE marking.
• Certification & compliance engineers - to prepare technical documentation showing RED Article 3.2 compliance.
• Chipset vendors, modem designers and mobile network operators - to ensure devices interoperate without causing harmful interference in FDD/TDD and CA deployments.

Related Standards and References

• ETSI TS 136 101 (3GPP Releases mapping and band definitions)
• Commission Decision 2010/267/EU, ECC Decision (09)03, CEPT Report 30 (relevant for Band 20 TRP considerations)
• 3GPP technical releases for LTE / LTE-Advanced (Releases 8–12)

Keywords: E-UTRA, LTE, LTE-Advanced, UE, Radio Equipment Directive, harmonised standard, transmitter spectrum emission mask, spurious emissions, carrier aggregation, UL-MIMO, conformance testing, CE marking.

Standards Content (Sample)

Final draft ETSI EN 301 908-13 V11.1.0 (2016-05)

HARMONISED EUROPEAN STANDARD
IMT cellular networks;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU;
Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA)
User Equipment (UE)
2 Final draft ETSI EN 301 908-13 V11.1.0 (2016-05)

Reference
REN/MSG-TFES-11-13-RED
Keywords
3G, 3GPP, cellular, digital, E-UTRA, IMT, LTE,
LTE-Advanced, mobile, radio, regulation, UMTS

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 Final draft ETSI EN 301 908-13 V11.1.0 (2016-05)
Contents
Intellectual Property Rights . 8
Foreword . 8
Modal verbs terminology . 8
Introduction . 8
1 Scope . 9
2 References . 11
2.1 Normative references . 11
2.2 Informative references . 11
3 Definitions, symbols and abbreviations . 12
3.1 Definitions . 12
3.2 Symbols . 15
3.3 Abbreviations . 16
4 Technical requirements specifications . 18
4.1 Environmental profile . 18
4.2 Conformance requirements . 18
4.2.0 General . 18
4.2.1 Introduction. 18
4.2.2 Transmitter Maximum Output Power . 19
4.2.2.1 Transmitter maximum output power for Single Carrier . 19
4.2.2.1.1 Definition. 19
4.2.2.1.2 Limits . 19
4.2.2.1.3 Conformance . 19
4.2.2.2 Transmitter output power for intra-band contiguous Carrier Aggregation (DL CA and UL CA). 19
4.2.2.2.1 Definition. 19
4.2.2.2.2 Limits . 20
4.2.2.2.3 Conformance . 20
4.2.2.3 Transmitter output power for UL-MIMO . 20
4.2.2.3.1 Definition. 20
4.2.2.3.2 Limits . 21
4.2.2.3.3 Conformance . 21
4.2.3 Transmitter Spectrum Emission Mask . 21
4.2.3.1 Transmitter spectrum emission mask for Single Carrier . 21
4.2.3.1.1 Definition. 21
4.2.3.1.2 Limits . 21
4.2.3.1.3 Conformance . 22
4.2.3.2 Transmitter spectrum emission mask for intra-band contiguous Carrier Aggregation (DL CA and
UL CA) . 23
4.2.3.2.1 Definition. 23
4.2.3.2.2 Limits . 23
4.2.3.2.3 Conformance . 24
4.2.3.3 Transmitter spectrum emission mask for UL-MIMO . 24
4.2.3.3.1 Definition. 24
4.2.3.3.2 Limits . 24
4.2.3.3.3 Conformance . 24
4.2.3.4 Transmitter spectrum emission mask for Multi-Cluster PUSCH within a component carrier . 24
4.2.3.4.1 Definition. 24
4.2.3.4.2 Limits . 24
4.2.3.4.3 Conformance . 24
4.2.4 Transmitter Spurious Emissions . 24
4.2.4.1 Transmitter spurious emissions for Single Carrier . 24
4.2.4.1.1 Definition. 24
4.2.4.1.2 Limits . 24
4.2.4.1.3 Conformance . 28
ETSI
4 Final draft ETSI EN 301 908-13 V11.1.0 (2016-05)
4.2.4.2 Transmitter spurious emissions for intra-band contiguous Carrier Aggregation (DL CA and UL
CA) . 28
4.2.4.2.1 Definition. 28
4.2.4.2.2 Limits . 28
4.2.4.2.3 Conformance . 30
4.2.4.3 Transmitter spurious emissions for UL-MIMO . 30
4.2.4.3.1 Definition. 30
4.2.4.3.2 Limits . 30
4.2.4.3.3 Conformance . 30
4.2.4.4 Transmitter spurious emissions for Multi-Cluster PUSCH within a component carrier . 30
4.2.4.4.1 Definition. 30
4.2.4.4.2 Limits . 31
4.2.4.4.3 Conformance . 31
4.2.5 Transmitter Minimum Output Power . 31
4.2.5.1 Transmitter minimum output power for Single Carrier. 31
4.2.5.1.1 Definition. 31
4.2.5.1.2 Limits . 31
4.2.5.1.3 Conformance . 31
4.2.5.2 Transmitter minimum output power for intra-band contiguous Carrier Aggregation (DL CA and
UL CA) . 31
4.2.5.2.1 Definition. 31
4.2.5.2.2 Limits . 31
4.2.5.2.3 Conformance . 32
4.2.5.3 Transmitter minimum output power for UL-MIMO . 32
4.2.5.3.1 Definition. 32
4.2.5.3.2 Limits . 32
4.2.5.3.3 Conformance . 32
4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 32
4.2.6.1 Receiver Adjacent Channel Selectivity (ACS) for Single Carrier . 32
4.2.6.1.1 Definition. 32
4.2.6.1.2 Limits . 32
4.2.6.1.3 Conformance . 33
4.2.6.2 Receiver Adjacent Channel Selectivity (ACS) for Carrier Aggregation in DL-only bands . 33
4.2.6.2.1 Definition. 33
4.2.6.2.2 Limits . 34
4.2.6.2.3 Conformance . 34
4.2.7 Receiver Blocking Characteristics . 34
4.2.7.1 Receiver Blocking Characteristics for Single Carrier . 34
4.2.7.1.1 Definition. 34
4.2.7.1.2 Limits . 34
4.2.7.1.3 Conformance . 35
4.2.7.2 Receiver Blocking Characteristics for Carrier Aggregation in DL-only bands . 36
4.2.7.2.1 Definition. 36
4.2.7.2.2 Limits . 36
4.2.7.2.3 Conformance . 37
4.2.8 Receiver Spurious Response . 37
4.2.8.1 Receiver Spurious Response for Single Carrier . 37
4.2.8.1.1 Definition. 37
4.2.8.1.2 Limits . 37
4.2.8.1.3 Conformance . 38
4.2.8.2 Receiver Spurious Response for Carrier Aggregation in DL-only bands . 38
4.2.8.2.1 Definition. 38
4.2.8.2.2 Limits . 38
4.2.8.2.3 Conformance . 38
4.2.9 Receiver Intermodulation Characteristics . 38
4.2.9.1 Receiver Intermodulation Characteristics for Single Carrier . 38
4.2.9.1.1 Definition. 38
4.2.9.1.2 Limits . 38
4.2.9.1.3 Conformance . 39
4.2.9.2 Receiver Intermodulation Characteristics for Carrier Aggregation in DL-only bands . 39
4.2.9.2.1 Definition. 39
4.2.9.2.2 Limits . 39
ETSI
5 Final draft ETSI EN 301 908-13 V11.1.0 (2016-05)
4.2.9.2.3 Conformance . 39
4.2.10 Receiver Spurious Emissions . 39
4.2.10.1 Receiver Spurious Emissions for Single Carrier . 39
4.2.10.1.1 Definition. 39
4.2.10.1.2 Limits . 39
4.2.10.1.3 Conformance . 40
4.2.10.2 Receiver Spurious Emissions in DL-only bands . 40
4.2.10.2.1 Definition. 40
4.2.10.2.2 Limits . 40
4.2.10.2.3 Conformance . 40
4.2.11 Transmitter Adjacent Channel Leakage Power Ratio . 40
4.2.11.1 Transmitter adjacent channel leakage power ratio for Single Carrier . 40
4.2.11.1.1 Definition. 40
4.2.11.1.2 Limits . 40
4.2.11.1.3 Conformance . 41
4.2.11.2 Transmitter adjacent channel leakage power ratio for intra-band contiguous Carrier Aggregation
(DL CA and UL CA). 41
4.2.11.2.1 Definition. 41
4.2.11.2.2 Limits . 42
4.2.11.2.3 Conformance . 42
4.2.11.3 Transmitter adjacent channel leakage power ratio for UL-MIMO . 43
4.2.11.3.1 Definition. 43
4.2.11.3.2 Limits . 43
4.2.11.3.3 Conformance . 44
4.2.11.4 Transmitter adjacent channel leakage power ratio for Multi-Cluster PUSCH within a component
carrier . 44
4.2.11.4.1 Definition. 44
4.2.11.4.2 Limits . 44
4.2.11.4.3 Conformance . 44
4.2.12 Receiver Reference Sensitivity Level . 45
4.2.12.0 General . 45
4.2.12.1 Receiver Reference Sensitivity Level for Single Carrier . 45
4.2.12.1.1 Definition. 45
4.2.12.1.2 Limits . 45
4.2.12.1.3 Conformance . 45
5 Testing for compliance with technical requirements . 45
5.1 Environmental conditions for testing . 45
5.2 Interpretation of the measurement results . 46
5.3 Essential radio test suites . 47
5.3.0 General . 47
5.3.1 Transmitter Maximum Output Power . 47
5.3.1.1 Transmitter maximum output power for Single Carrier . 47
5.3.1.1.1 Method of test . 47
5.3.1.1.2 Test requirements . 47
5.3.1.2 Transmitter maximum output power for intra-band contiguous Carrier Aggregation (DL CA and
UL CA) . 48
5.3.1.2.1 Method of test . 48
5.3.1.2.2 Test requirements . 48
5.3.1.3 Transmitter maximum output power for UL-MIMO . 49
5.3.1.3.1 Method of test . 49
5.3.1.3.2 Test requirements . 49
5.3.2 Transmitter Spectrum Emission Mask . 49
5.3.2.1 Transmitter spectrum emission mask for Single Carrier . 49
5.3.2.1.1 Method of test . 49
5.3.2.1.2 Test requirements . 50
5.3.2.2 Transmitter spectrum emission mask for intra-band contiguous Carrier Aggregation (DL CA and
UL CA) . 50
5.3.2.2.1 Method of test . 50
5.3.2.2.2 Test requirements . 51
5.3.2.3 Transmitter spectrum emission mask for UL-MIMO . 51
5.3.2.3.1 Method of test . 51
ETSI
6 Final draft ETSI EN 301 908-13 V11.1.0 (2016-05)
5.3.2.3.2 Test requirements . 52
5.3.2.4 Transmitter spectrum emission mask for Multi-Cluster PUSCH within a component carrier . 52
5.3.2.4.1 Method of test . 52
5.3.2.4.2 Test requirements . 53
5.3.3 Transmitter Spurious Emissions . 53
5.3.3.1 Transmitter spurious emissions for Single Carrier . 53
5.3.3.1.1 Method of test . 53
5.3.3.1.2 Test requirements . 53
5.3.3.2 Transmitter spurious emissions for intra-band contiguous Carrier Aggregation (DL CA and UL
CA) . 54
5.3.3.2.1 Method of test . 54
5.3.3.2.2 Test requirements . 54
5.3.3.3 Transmitter spurious emissions for UL-MIMO . 55
5.3.3.3.1 Method of test . 55
5.3.3.3.2 Test requirements . 55
5.3.3.4 Transmitter spurious emissions for Multi-Cluster PUSCH within a component carrier . 55
5.3.3.4.1 Method of test . 55
5.3.3.4.2 Test requirements . 56
5.3.4 Transmitter Minimum Output Power . 56
5.3.4.1 Transmitter minimum output power for Single Carrier. 56
5.3.4.1.1 Method of test . 56
5.3.4.1.2 Test requirements . 57
5.3.4.2 Transmitter minimum output power for intra-band contiguous Carrier Aggregation (DL CA and
UL CA) . 57
5.3.4.2.1 Method of test . 57
5.3.4.2.2 Test requirements . 58
5.3.4.3 Transmitter minimum output power for UL-MIMO . 58
5.3.4.3.1 Method of test . 58
5.3.4.3.2 Test requirements . 59
5.3.5 Receiver Adjacent Channel Selectivity (ACS) . 59
5.3.5.1 Receiver Adjacent Channel Selectivity (ACS) for Single Carrier . 59
5.3.5.1.1 Method of test . 59
5.3.5.1.2 Test requirements . 60
5.3.5.2 Receiver Adjacent Channel Selectivity (ACS) for Carrier Aggregation in DL-only bands . 60
5.3.5.2.1 Method of test . 60
5.3.5.2.2 Test requirements . 61
5.3.6 Receiver Blocking Characteristics . 61
5.3.6.1 Receiver Blocking Characteristics for Single Carrier . 61
5.3.6.1.1 Method of test . 61
5.3.6.1.2 Test requirements . 63
5.3.6.2 Receiver Blocking Characteristics for Carrier Aggregation in DL-only bands . 63
5.3.6.2.1 Method of test . 63
5.3.6.2.2 Test requirements . 65
5.3.7 Receiver Spurious Response . 65
5.3.7.1 Receiver Spurious Response for Single Carrier . 65
5.3.7.1.1 Method of test . 65
5.3.7.1.2 Test requirements . 66
5.3.7.2 Receiver Spurious Response for Carrier Aggregation in DL-only bands . 66
5.3.7.2.1 Method of test . 66
5.3.7.2.2 Test requirements . 66
5.3.8 Receiver Intermodulation Characteristics . 67
5.3.8.1 Receiver Intermodulation Characteristics for Single Carrier . 67
5.3.8.1.1 Method of test . 67
5.3.8.1.2 Test requirements . 67
5.3.8.2 Receiver Intermodulation Characteristics for Carrier Aggregation in DL-only bands . 68
5.3.8.2.1 Method of test . 68
5.3.8.2.2 Test requirements . 68
5.3.9 Receiver Spurious Emissions . 69
5.3.9.1 Receiver Spurious Emissions for Single Carrier . 69
5.3.9.1.1 Method of test . 69
5.3.9.1.2 Test requirements . 69
5.3.9.2 Receiver Spurious Emissions in DL-only bands . 69
ETSI
7 Final draft ETSI EN 301 908-13 V11.1.0 (2016-05)
5.3.9.2.1 Method of test . 69
5.3.9.2.2 Test requirements . 70
5.3.10 Transmitter Adjacent Channel Leakage Power Ratio . 70
5.3.10.1 Transmitter adjacent channel leakage power ratio for Single Carrier . 70
5.3.10.1.1 Method of test . 70
5.3.10.1.2 Test requirements . 71
5.3.10.2 Transmitter adjacent channel leakage power ratio for intra-band contiguous Carrier Aggregation
(DL CA and UL CA). 71
5.3.10.2.1 Method of test . 71
5.3.10.2.2 Test requirements . 72
5.3.10.3 Transmitter adjacent channel leakage power ratio for UL-MIMO . 72
5.3.10.3.1 Method of test . 72
5.3.10.3.2 Test requirements . 73
5.3.10.4 Transmitter adjacent channel leakage power ratio for Multi-Cluster PUSCH within a component
carrier . 73
5.3.10.4.1 Method of test . 73
5.3.10.4.2 Test requirements . 74
5.3.11 Receiver Reference Sensitivity Level . 74
5.3.11.1 Receiver Reference Sensitivity Level for Single Carrier . 74
5.3.11.1.1 Method of test . 74
5.3.11.1.2 Test requirements . 75
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 76
Annex B (normative): Environmental profile . 77
B.1 General . 77
B.1.1 Introduction . 77
B.1.2 Temperature . 77
B.1.3 Voltage . 77
B.1.4 Test environment . 78
Annex C (informative): Bibliography . 79
History . 80

ETSI
8 Final draft ETSI EN 301 908-13 V11.1.0 (2016-05)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or
...

HARMONISED EUROPEAN STANDARD
IMT cellular networks;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU;
Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA)
User Equipment (UE)
2 ETSI EN 301 908-13 V11.1.1 (2016-07)

Reference
REN/MSG-TFES-11-13-RED
Keywords
3G, 3GPP, cellular, digital, E-UTRA, IMT, LTE,
LTE-Advanced, mobile, radio, regulation, UMTS

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: [phone]  Fax: [phone]

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 ETSI EN 301 908-13 V11.1.1 (2016-07)
Contents
Intellectual Property Rights . 8
Foreword . 8
Modal verbs terminology . 8
Introduction . 8
1 Scope . 9
2 References . 11
2.1 Normative references . 11
2.2 Informative references . 11
3 Definitions, symbols and abbreviations . 12
3.1 Definitions . 12
3.2 Symbols . 15
3.3 Abbreviations . 16
4 Technical requirements specifications . 18
4.1 Environmental profile . 18
4.2 Conformance requirements . 18
4.2.0 General . 18
4.2.1 Introduction. 18
4.2.2 Transmitter Maximum Output Power . 19
4.2.2.1 Transmitter maximum output power for Single Carrier . 19
4.2.2.1.1 Definition. 19
4.2.2.1.2 Limits . 19
4.2.2.1.3 Conformance . 19
4.2.2.2 Transmitter output power for intra-band contiguous Carrier Aggregation (DL CA and UL CA). 19
4.2.2.2.1 Definition. 19
4.2.2.2.2 Limits . 20
4.2.2.2.3 Conformance . 20
4.2.2.3 Transmitter output power for UL-MIMO . 20
4.2.2.3.1 Definition. 20
4.2.2.3.2 Limits . 21
4.2.2.3.3 Conformance . 21
4.2.3 Transmitter Spectrum Emission Mask . 21
4.2.3.1 Transmitter spectrum emission mask for Single Carrier . 21
4.2.3.1.1 Definition. 21
4.2.3.1.2 Limits . 21
4.2.3.1.3 Conformance . 23
4.2.3.2 Transmitter spectrum emission mask for intra-band contiguous Carrier Aggregation (DL CA and
UL CA) . 23
4.2.3.2.1 Definition. 23
4.2.3.2.2 Limits . 23
4.2.3.2.3 Conformance . 24
4.2.3.3 Transmitter spectrum emission mask for UL-MIMO . 24
4.2.3.3.1 Definition. 24
4.2.3.3.2 Limits . 24
4.2.3.3.3 Conformance . 24
4.2.3.4 Transmitter spectrum emission mask for Multi-Cluster PUSCH within a component carrier . 24
4.2.3.4.1 Definition. 24
4.2.3.4.2 Limits . 25
4.2.3.4.3 Conformance . 25
4.2.4 Transmitter Spurious Emissions . 25
4.2.4.1 Transmitter spurious emissions for Single Carrier . 25
4.2.4.1.1 Definition. 25
4.2.4.1.2 Limits . 25
4.2.4.1.3 Conformance . 28
ETSI
4 ETSI EN 301 908-13 V11.1.1 (2016-07)
4.2.4.2 Transmitter spurious emissions for intra-band contiguous Carrier Aggregation (DL CA and UL
CA) . 28
4.2.4.2.1 Definition. 28
4.2.4.2.2 Limits . 28
4.2.4.2.3 Conformance . 30
4.2.4.3 Transmitter spurious emissions for UL-MIMO . 31
4.2.4.3.1 Definition. 31
4.2.4.3.2 Limits . 31
4.2.4.3.3 Conformance . 31
4.2.4.4 Transmitter spurious emissions for Multi-Cluster PUSCH within a component carrier . 31
4.2.4.4.1 Definition. 31
4.2.4.4.2 Limits . 31
4.2.4.4.3 Conformance . 31
4.2.5 Transmitter Minimum Output Power . 31
4.2.5.1 Transmitter minimum output power for Single Carrier. 31
4.2.5.1.1 Definition. 31
4.2.5.1.2 Limits . 32
4.2.5.1.3 Conformance . 32
4.2.5.2 Transmitter minimum output power for intra-band contiguous Carrier Aggregation (DL CA and
UL CA) . 32
4.2.5.2.1 Definition. 32
4.2.5.2.2 Limits . 32
4.2.5.2.3 Conformance . 32
4.2.5.3 Transmitter minimum output power for UL-MIMO . 32
4.2.5.3.1 Definition. 32
4.2.5.3.2 Limits . 33
4.2.5.3.3 Conformance . 33
4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 33
4.2.6.1 Receiver Adjacent Channel Selectivity (ACS) for Single Carrier . 33
4.2.6.1.1 Definition. 33
4.2.6.1.2 Limits . 33
4.2.6.1.3 Conformance . 34
4.2.6.2 Receiver Adjacent Channel Selectivity (ACS) for Carrier Aggregation in DL-only bands . 34
4.2.6.2.1 Definition. 34
4.2.6.2.2 Limits . 34
4.2.6.2.3 Conformance . 34
4.2.7 Receiver Blocking Characteristics . 35
4.2.7.1 Receiver Blocking Characteristics for Single Carrier . 35
4.2.7.1.1 Definition. 35
4.2.7.1.2 Limits . 35
4.2.7.1.3 Conformance . 36
4.2.7.2 Receiver Blocking Characteristics for Carrier Aggregation in DL-only bands . 37
4.2.7.2.1 Definition. 37
4.2.7.2.2 Limits . 37
4.2.7.2.3 Conformance . 38
4.2.8 Receiver Spurious Response . 38
4.2.8.1 Receiver Spurious Response for Single Carrier . 38
4.2.8.1.1 Definition. 38
4.2.8.1.2 Limits . 38
4.2.8.1.3 Conformance . 39
4.2.8.2 Receiver Spurious Response for Carrier Aggregation in DL-only bands . 39
4.2.8.2.1 Definition. 39
4.2.8.2.2 Limits . 39
4.2.8.2.3 Conformance . 39
4.2.9 Receiver Intermodulation Characteristics . 39
4.2.9.1 Receiver Intermodulation Characteristics for Single Carrier . 39
4.2.9.1.1 Definition. 39
4.2.9.1.2 Limits . 39
4.2.9.1.3 Conformance . 40
4.2.9.2 Receiver Intermodulation Characteristics for Carrier Aggregation in DL-only bands . 40
4.2.9.2.1 Definition. 40
4.2.9.2.2 Limits . 40
ETSI
5 ETSI EN 301 908-13 V11.1.1 (2016-07)
4.2.9.2.3 Conformance . 40
4.2.10 Receiver Spurious Emissions . 40
4.2.10.1 Receiver Spurious Emissions for Single Carrier . 40
4.2.10.1.1 Definition. 40
4.2.10.1.2 Limits . 41
4.2.10.1.3 Conformance . 41
4.2.10.2 Receiver Spurious Emissions in DL-only bands . 41
4.2.10.2.1 Definition. 41
4.2.10.2.2 Limits . 41
4.2.10.2.3 Conformance . 41
4.2.11 Transmitter Adjacent Channel Leakage Power Ratio . 41
4.2.11.1 Transmitter adjacent channel leakage power ratio for Single Carrier . 41
4.2.11.1.1 Definition. 41
4.2.11.1.2 Limits . 42
4.2.11.1.3 Conformance . 42
4.2.11.2 Transmitter adjacent channel leakage power ratio for intra-band contiguous Carrier Aggregation
(DL CA and UL CA). 43
4.2.11.2.1 Definition. 43
4.2.11.2.2 Limits . 43
4.2.11.2.3 Conformance . 44
4.2.11.3 Transmitter adjacent channel leakage power ratio for UL-MIMO . 44
4.2.11.3.1 Definition. 44
4.2.11.3.2 Limits . 44
4.2.11.3.3 Conformance . 45
4.2.11.4 Transmitter adjacent channel leakage power ratio for Multi-Cluster PUSCH within a component
carrier . 45
4.2.11.4.1 Definition. 45
4.2.11.4.2 Limits . 45
4.2.11.4.3 Conformance . 45
4.2.12 Receiver Reference Sensitivity Level . 46
4.2.12.0 General . 46
4.2.12.1 Receiver Reference Sensitivity Level for Single Carrier . 46
4.2.12.1.1 Definition. 46
4.2.12.1.2 Limits . 46
4.2.12.1.3 Conformance . 46
5 Testing for compliance with technical requirements . 47
5.1 Environmental conditions for testing . 47
5.2 Interpretation of the measurement results . 47
5.3 Essential radio test suites . 48
5.3.0 General . 48
5.3.1 Transmitter Maximum Output Power . 48
5.3.1.1 Transmitter maximum output power for Single Carrier . 48
5.3.1.1.1 Method of test . 48
5.3.1.1.2 Test requirements . 49
5.3.1.2 Transmitter maximum output power for intra-band contiguous Carrier Aggregation (DL CA and
UL CA) . 49
5.3.1.2.1 Method of test . 49
5.3.1.2.2 Test requirements . 50
5.3.1.3 Transmitter maximum output power for UL-MIMO . 50
5.3.1.3.1 Method of test . 50
5.3.1.3.2 Test requirements . 50
5.3.2 Transmitter Spectrum Emission Mask . 51
5.3.2.1 Transmitter spectrum emission mask for Single Carrier . 51
5.3.2.1.1 Method of test . 51
5.3.2.1.2 Test requirements . 51
5.3.2.2 Transmitter spectrum emission mask for intra-band contiguous Carrier Aggregation (DL CA and
UL CA) . 52
5.3.2.2.1 Method of test . 52
5.3.2.2.2 Test requirements . 52
5.3.2.3 Transmitter spectrum emission mask for UL-MIMO . 53
5.3.2.3.1 Method of test . 53
ETSI
6 ETSI EN 301 908-13 V11.1.1 (2016-07)
5.3.2.3.2 Test requirements . 53
5.3.2.4 Transmitter spectrum emission mask for Multi-Cluster PUSCH within a component carrier . 53
5.3.2.4.1 Method of test . 53
5.3.2.4.2 Test requirements . 54
5.3.3 Transmitter Spurious Emissions . 54
5.3.3.1 Transmitter spurious emissions for Single Carrier . 54
5.3.3.1.1 Method of test . 54
5.3.3.1.2 Test requirements . 55
5.3.3.2 Transmitter spurious emissions for intra-band contiguous Carrier Aggregation (DL CA and UL
CA) . 55
5.3.3.2.1 Method of test . 55
5.3.3.2.2 Test requirements . 56
5.3.3.3 Transmitter spurious emissions for UL-MIMO . 56
5.3.3.3.1 Method of test . 56
5.3.3.3.2 Test requirements . 57
5.3.3.4 Transmitter spurious emissions for Multi-Cluster PUSCH within a component carrier . 57
5.3.3.4.1 Method of test . 57
5.3.3.4.2 Test requirements . 58
5.3.4 Transmitter Minimum Output Power . 58
5.3.4.1 Transmitter minimum output power for Single Carrier. 58
5.3.4.1.1 Method of test . 58
5.3.4.1.2 Test requirements . 59
5.3.4.2 Transmitter minimum output power for intra-band contiguous Carrier Aggregation (DL CA and
UL CA) . 59
5.3.4.2.1 Method of test . 59
5.3.4.2.2 Test requirements . 59
5.3.4.3 Transmitter minimum output power for UL-MIMO . 60
5.3.4.3.1 Method of test . 60
5.3.4.3.2 Test requirements . 60
5.3.5 Receiver Adjacent Channel Selectivity (ACS) . 60
5.3.5.1 Receiver Adjacent Channel Selectivity (ACS) for Single Carrier . 60
5.3.5.1.1 Method of test . 60
5.3.5.1.2 Test requirements . 61
5.3.5.2 Receiver Adjacent Channel Selectivity (ACS) for Carrier Aggregation in DL-only bands . 62
5.3.5.2.1 Method of test . 62
5.3.5.2.2 Test requirements . 63
5.3.6 Receiver Blocking Characteristics . 63
5.3.6.1 Receiver Blocking Characteristics for Single Carrier . 63
5.3.6.1.1 Method of test . 63
5.3.6.1.2 Test requirements . 65
5.3.6.2 Receiver Blocking Characteristics for Carrier Aggregation in DL-only bands . 65
5.3.6.2.1 Method of test . 65
5.3.6.2.2 Test requirements . 67
5.3.7 Receiver Spurious Response . 67
5.3.7.1 Receiver Spurious Response for Single Carrier . 67
5.3.7.1.1 Method of test . 67
5.3.7.1.2 Test requirements . 68
5.3.7.2 Receiver Spurious Response for Carrier Aggregation in DL-only bands . 68
5.3.7.2.1 Method of test . 68
5.3.7.2.2 Test requirements . 68
5.3.8 Receiver Intermodulation Characteristics . 68
5.3.8.1 Receiver Intermodulation Characteristics for Single Carrier . 68
5.3.8.1.1 Method of test . 68
5.3.8.1.2 Test requirements . 69
5.3.8.2 Receiver Intermodulation Characteristics for Carrier Aggregation in DL-only bands . 69
5.3.8.2.1 Method of test . 69
5.3.8.2.2 Test requirements . 70
5.3.9 Receiver Spurious Emissions . 70
5.3.9.1 Receiver Spurious Emissions for Single Carrier . 70
5.3.9.1.1 Method of test . 70
5.3.9.1.2 Test requirements . 71
5.3.9.2 Receiver Spurious Emissions in DL-only bands . 71
ETSI
7 ETSI EN 301 908-13 V11.1.1 (2016-07)
5.3.9.2.1 Method of test . 71
5.3.9.2.2 Test requirements . 72
5.3.10 Transmitter Adjacent Channel Leakage Power Ratio . 72
5.3.10.1 Transmitter adjacent channel leakage power ratio for Single Carrier . 72
5.3.10.1.1 Method of test . 72
5.3.10.1.2 Test requirements . 73
5.3.10.2 Transmitter adjacent channel leakage power ratio for intra-band contiguous Carrier Aggregation
(DL CA and UL CA). 73
5.3.10.2.1 Method of test . 73
5.3.10.2.2 Test requirements . 74
5.3.10.3 Transmitter adjacent channel leakage power ratio for UL-MIMO . 74
5.3.10.3.1 Method of test . 74
5.3.10.3.2 Test requirements . 75
5.3.10.4 Transmitter adjacent channel leakage power ratio for Multi-Cluster PUSCH within a component
carrier . 75
5.3.10.4.1 Method of test . 75
5.3.10.4.2 Test requirements . 76
5.3.11 Receiver Reference Sensitivity Level . 76
5.3.11.1 Receiver Reference Sensitivity Level for Single Carrier . 76
5.3.11.1.1 Method of test . 76
5.3.11.1.2 Test requirements . 77
Annex A (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 78
Annex B (normative): Environmental profile . 79
B.1 General . 79
B.1.1 Introduction . 79
B.1.2 Temperature . 79
B.1.3 Voltage . 79
B.1.4 Test environment . 80
Annex C (informative): Bibliography . 81
History . 82

ETSI
8 ETSI EN 301 908-13 V11.1.1 (2016-07)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonised Europ
...

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.IMT cellular networks - Harmonised Standard covering the essential requirements of article 3.2 of the Radio Equipment Directive 2014/53/EU - Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)33.070.99Druge mobilne storitveOther mobile services33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:ETSI EN 301 908-13 V11.1.1 (2016-07)SIST EN 301 908-13 V11.1.1:2016en01-oktober-2016SIST EN 301 908-13 V11.1.1:2016SLOVENSKI
STANDARD
HARMONISED EUROPEAN STANDARD SIST EN 301 908-13 V11.1.1:2016

ETSI ETSI EN 301 908-13 V11.1.1 (2016-07) 2
Reference REN/MSG-TFES-11-13-RED Keywords 3G, 3GPP, cellular, digital, E-UTRA, IMT, LTE, LTE-Advanced, mobile, radio, regulation, UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: [phone]
Fax: [phone]
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 908-13 V11.1.1:2016

ETSI ETSI EN 301 908-13 V11.1.1 (2016-07) 3 Contents Intellectual Property Rights . 8 Foreword . 8 Modal verbs terminology . 8 Introduction . 8 1 Scope . 9 2 References . 11 2.1 Normative references . 11 2.2 Informative references . 11 3 Definitions, symbols and abbreviations . 12 3.1 Definitions . 12 3.2 Symbols . 15 3.3 Abbreviations . 16 4 Technical requirements specifications . 18 4.1 Environmental profile . 18 4.2 Conformance requirements . 18 4.2.0 General . 18 4.2.1 Introduction. 18 4.2.2 Transmitter Maximum Output Power . 19 4.2.2.1 Transmitter maximum output power for Single Carrier . 19 4.2.2.1.1 Definition. 19 4.2.2.1.2 Limits . 19 4.2.2.1.3 Conformance . 19 4.2.2.2 Transmitter output power for intra-band contiguous Carrier Aggregation (DL CA and UL CA). 19 4.2.2.2.1 Definition. 19 4.2.2.2.2 Limits . 20 4.2.2.2.3 Conformance . 20 4.2.2.3 Transmitter output power for UL-MIMO . 20 4.2.2.3.1 Definition. 20 4.2.2.3.2 Limits . 21 4.2.2.3.3 Conformance . 21 4.2.3 Transmitter Spectrum Emission Mask . 21 4.2.3.1 Transmitter spectrum emission mask for Single Carrier . 21 4.2.3.1.1 Definition. 21 4.2.3.1.2 Limits . 21 4.2.3.1.3 Conformance . 23 4.2.3.2 Transmitter spectrum emission mask for intra-band contiguous Carrier Aggregation (DL CA and UL CA) . 23 4.2.3.2.1 Definition. 23 4.2.3.2.2 Limits . 23 4.2.3.2.3 Conformance . 24 4.2.3.3 Transmitter spectrum emission mask for UL-MIMO . 24 4.2.3.3.1 Definition. 24 4.2.3.3.2 Limits . 24 4.2.3.3.3 Conformance . 24 4.2.3.4 Transmitter spectrum emission mask for Multi-Cluster PUSCH within a component carrier . 24 4.2.3.4.1 Definition. 24 4.2.3.4.2 Limits . 25 4.2.3.4.3 Conformance . 25 4.2.4 Transmitter Spurious Emissions . 25 4.2.4.1 Transmitter spurious emissions for Single Carrier . 25 4.2.4.1.1 Definition. 25 4.2.4.1.2 Limits . 25 4.2.4.1.3 Conformance . 28 SIST EN 301 908-13 V11.1.1:2016

ETSI ETSI EN 301 908-13 V11.1.1 (2016-07) 4 4.2.4.2 Transmitter spurious emissions for intra-band contiguous Carrier Aggregation (DL CA and UL CA) . 28 4.2.4.2.1 Definition. 28 4.2.4.2.2 Limits . 28 4.2.4.2.3 Conformance . 30 4.2.4.3 Transmitter spurious emissions for UL-MIMO . 31 4.2.4.3.1 Definition. 31 4.2.4.3.2 Limits . 31 4.2.4.3.3 Conformance . 31 4.2.4.4 Transmitter spurious emissions for Multi-Cluster PUSCH within a component carrier . 31 4.2.4.4.1 Definition. 31 4.2.4.4.2 Limits . 31 4.2.4.4.3 Conformance . 31 4.2.5 Transmitter Minimum Output Power . 31 4.2.5.1 Transmitter minimum output power for Single Carrier. 31 4.2.5.1.1 Definition. 31 4.2.5.1.2 Limits . 32 4.2.5.1.3 Conformance . 32 4.2.5.2 Transmitter minimum output power for intra-band contiguous Carrier Aggregation (DL CA and UL CA) . 32 4.2.5.2.1 Definition. 32 4.2.5.2.2 Limits . 32 4.2.5.2.3 Conformance . 32 4.2.5.3 Transmitter minimum output power for UL-MIMO . 32 4.2.5.3.1 Definition. 32 4.2.5.3.2 Limits . 33 4.2.5.3.3 Conformance . 33 4.2.6 Receiver Adjacent Channel Selectivity (ACS) . 33 4.2.6.1 Receiver Adjacent Channel Selectivity (ACS) for Single Carrier . 33 4.2.6.1.1 Definition. 33 4.2.6.1.2 Limits . 33 4.2.6.1.3 Conformance . 34 4.2.6.2 Receiver Adjacent Channel Selectivity (ACS) for Carrier Aggregation in DL-only bands . 34 4.2.6.2.1 Definition. 34 4.2.6.2.2 Limits . 34 4.2.6.2.3 Conformance . 34 4.2.7 Receiver Blocking Characteristics . 35 4.2.7.1 Receiver Blocking Characteristics for Single Carrier . 35 4.2.7.1.1 Definition. 35 4.2.7.1.2 Limits . 35 4.2.7.1.3 Conformance . 36 4.2.7.2 Receiver Blocking Characteristics for Carrier Aggregation in DL-only bands . 37 4.2.7.2.1 Definition. 37 4.2.7.2.2 Limits . 37 4.2.7.2.3 Conformance . 38 4.2.8 Receiver Spurious Response . 38 4.2.8.1 Receiver Spurious Response for Single Carrier . 38 4.2.8.1.1 Definition. 38 4.2.8.1.2 Limits . 38 4.2.8.1.3 Conformance . 39 4.2.8.2 Receiver Spurious Response for Carrier Aggregation in DL-only bands . 39 4.2.8.2.1 Definition. 39 4.2.8.2.2 Limits . 39 4.2.8.2.3 Conformance . 39 4.2.9 Receiver Intermodulation Characteristics . 39 4.2.9.1 Receiver Intermodulation Characteristics for Single Carrier . 39 4.2.9.1.1 Definition. 39 4.2.9.1.2 Limits . 39 4.2.9.1.3 Conformance . 40 4.2.9.2 Receiver Intermodulation Characteristics for Carrier Aggregation in DL-only bands . 40 4.2.9.2.1 Definition. 40 4.2.9.2.2 Limits . 40 SIST EN 301 908-13 V11.1.1:2016

ETSI ETSI EN 301 908-13 V11.1.1 (2016-07) 5 4.2.9.2.3 Conformance . 40 4.2.10 Receiver Spurious Emissions . 40 4.2.10.1 Receiver Spurious Emissions for Single Carrier . 40 4.2.10.1.1 Definition. 40 4.2.10.1.2 Limits . 41 4.2.10.1.3 Conformance . 41 4.2.10.2 Receiver Spurious Emissions in DL-only bands . 41 4.2.10.2.1 Definition. 41 4.2.10.2.2 Limits . 41 4.2.10.2.3 Conformance . 41 4.2.11 Transmitter Adjacent Channel Leakage Power Ratio . 41 4.2.11.1 Transmitter adjacent channel leakage power ratio for Single Carrier . 41 4.2.11.1.1 Definition. 41 4.2.11.1.2 Limits . 42 4.2.11.1.3 Conformance . 42 4.2.11.2 Transmitter adjacent channel leakage power ratio for intra-band contiguous Carrier Aggregation (DL CA and UL CA). 43 4.2.11.2.1 Definition. 43 4.2.11.2.2 Limits . 43 4.2.11.2.3 Conformance . 44 4.2.11.3 Transmitter adjacent channel leakage power ratio for UL-MIMO . 44 4.2.11.3.1 Definition. 44 4.2.11.3.2 Limits . 44 4.2.11.3.3 Conformance . 45 4.2.11.4 Transmitter adjacent channel leakage power ratio for Multi-Cluster PUSCH within a component carrier . 45 4.2.11.4.1 Definition. 45 4.2.11.4.2 Limits . 45 4.2.11.4.3 Conformance . 45 4.2.12 Receiver Reference Sensitivity Level . 46 4.2.12.0 General . 46 4.2.12.1 Receiver Reference Sensitivity Level for Single Carrier . 46 4.2.12.1.1 Definition. 46 4.2.12.1.2 Limits . 46 4.2.12.1.3 Conformance . 46 5 Testing for compliance with technical requirements . 47 5.1 Environmental conditions for testing . 47 5.2 Interpretation of the measurement results . 47 5.3 Essential radio test suites . 48 5.3.0 General . 48 5.3.1 Transmitter Maximum Output Power . 48 5.3.1.1 Transmitter maximum output power for Single Carrier . 48 5.3.1.1.1 Method of test . 48 5.3.1.1.2 Test requirements . 49 5.3.1.2 Transmitter maximum output power for intra-band contiguous Carrier Aggregation (DL CA and UL CA) . 49 5.3.1.2.1 Method of test . 49 5.3.1.2.2 Test requirements . 50 5.3.1.3 Transmitter maximum output power for UL-MIMO . 50 5.3.1.3.1 Method of test . 50 5.3.1.3.2 Test requirements . 50 5.3.2 Transmitter Spectrum Emission Mask . 51 5.3.2.1 Transmitter spectrum emission mask for Single Carrier . 51 5.3.2.1.1 Method of test . 51 5.3.2.1.2 Test requirements . 51 5.3.2.2 Transmitter spectrum emission mask for intra-band contiguous Carrier Aggregation (DL CA and UL CA) . 52 5.3.2.2.1 Method of test . 52 5.3.2.2.2 Test requirements . 52 5.3.2.3 Transmitter spectrum emission mask for UL-MIMO . 53 5.3.2.3.1 Method of test . 53 SIST EN 301 908-13 V11.1.1:2016

ETSI ETSI EN 301 908-13 V11.1.1 (2016-07) 6 5.3.2.3.2 Test requirements . 53 5.3.2.4 Transmitter spectrum emission mask for Multi-Cluster PUSCH within a component carrier . 53 5.3.2.4.1 Method of test . 53 5.3.2.4.2 Test requirements . 54 5.3.3 Transmitter Spurious Emissions . 54 5.3.3.1 Transmitter spurious emissions for Single Carrier . 54 5.3.3.1.1 Method of test . 54 5.3.3.1.2 Test requirements . 55 5.3.3.2 Transmitter spurious emissions for intra-band contiguous Carrier Aggregation (DL CA and UL CA) . 55 5.3.3.2.1 Method of test . 55 5.3.3.2.2 Test requirements . 56 5.3.3.3 Transmitter spurious emissions for UL-MIMO . 56 5.3.3.3.1 Method of test . 56 5.3.3.3.2 Test requirements . 57 5.3.3.4 Transmitter spurious emissions for Multi-Cluster PUSCH within a component carrier . 57 5.3.3.4.1 Method of test . 57 5.3.3.4.2 Test requirements . 58 5.3.4 Transmitter Minimum Output Power . 58 5.3.4.1 Transmitter minimum output power for Single Carrier. 58 5.3.4.1.1 Method of test . 58 5.3.4.1.2 Test requirements . 59 5.3.4.2 Transmitter minimum output power for intra-band contiguous Carrier Aggregation (DL CA and UL CA) . 59 5.3.4.2.1 Method of test . 59 5.3.4.2.2 Test requirements . 59 5.3.4.3 Transmitter minimum output power for UL-MIMO . 60 5.3.4.3.1 Method of test . 60 5.3.4.3.2 Test requirements . 60 5.3.5 Receiver Adjacent Channel Selectivity (ACS) . 60 5.3.5.1 Receiver Adjacent Channel Selectivity (ACS) for Single Carrier . 60 5.3.5.1.1 Method of test . 60 5.3.5.1.2 Test requirements . 61 5.3.5.2 Receiver Adjacent Channel Selectivity (ACS) for Carrier Aggregation in DL-only bands . 62 5.3.5.2.1 Method of test . 62 5.3.5.2.2 Test requirements . 63 5.3.6 Receiver Blocking Characteristics . 63 5.3.6.1 Receiver Blocking Characteristics for Single Carrier . 63 5.3.6.1.1 Method of test . 63 5.3.6.1.2 Test requirements . 65 5.3.6.2 Receiver Blocking Characteristics for Carrier Aggregation in DL-only bands . 65 5.3.6.2.1 Method of test . 65 5.3.6.2.2 Test requirements . 67 5.3.7 Receiver Spurious Response . 67 5.3.7.1 Receiver Spurious Response for Single Carrier . 67 5.3.7.1.1 Method of test . 67 5.3.7.1.2 Test requirements . 68 5.3.7.2 Receiver Spurious Response for Carrier Aggregation in DL-only bands . 68 5.3.7.2.1 Method of test . 68 5.3.7.2.2 Test requirements . 68 5.3.8 Receiver Intermodulation Characteristics . 68 5.3.8.1 Receiver Intermodulation Characteristics for Single Carrier . 68 5.3.8.1.1 Method of test . 68 5.3.8.1.2 Test requirements . 69 5.3.8.2 Receiver Intermodulation Characteristics for Carrier Aggregation in DL-only bands . 69 5.3.8.2.1 Method of test . 69 5.3.8.2.2 Test requirements . 70 5.3.9 Receiver Spurious Emissions . 70 5.3.9.1 Receiver Spurious Emissions for Single Carrier . 70 5.3.9.1.1 Method of test . 70 5.3.9.1.2 Test requirements . 71 5.3.9.2 Receiver Spurious Emissions in DL-only bands . 71 SIST EN 301 908-13 V11.1.1:2016

ETSI ETSI EN 301 908-13 V11.1.1 (2016-07) 7 5.3.9.2.1 Method of test . 71 5.3.9.2.2 Test requirements . 72 5.3.10 Transmitter Adjacent Channel Leakage Power Ratio . 72 5.3.10.1 Transmitter adjacent channel leakage power ratio for Single Carrier . 72 5.3.10.1.1 Method of test . 72 5.3.10.1.2 Test requirements . 73 5.3.10.2 Transmitter adjacent channel leakage power ratio for intra-band contiguous Carrier Aggregation (DL CA and UL CA). 73 5.3.10.2.1 Method of test . 73 5.3.10.2.2 Test requirements . 74 5.3.10.3 Transmitter adjacent channel leakage power ratio for UL-MIMO . 74 5.3.10.3.1 Method of test . 74 5.3.10.3.2 Test requirements . 75 5.3.10.4 Transmitter adjacent channel leakage power ratio for Multi-Cluster PUSCH within a component carrier . 75 5.3.10.4.1 Method of test . 75 5.3.10.4.2 Test requirements . 76 5.3.11 Receiver Reference Sensitivity Level . 76 5.3.11.1 Receiver Reference Sensitivity Level for Single Carrier . 76 5.3.11.1.1 Method of test . 76 5.3.11.1.2 Test requirements . 77 Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 78 Annex B (normative): Environmental profile . 79 B.1 General . 79 B.1.1 Introduction . 79 B.1.2 Temperature . 79 B.1.3 Voltage . 79 B.1.4 Test environment . 80 Annex C (informative): Bibliography . 81 History . 82
ETSI ETSI EN 301 908-13 V11.1.1 (2016-07) 8 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https://ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000
...