Unplasticized poly(vinyl chloride) (PVC-U) profiles for the fabrication of windows and doors - Classification, requirements and test methods - Part 1: Non-coated PVC-U profiles with light coloured surfaces

This part of EN 12608 specifies the classifications, requirements and test methods for non-coated unplasticized poly(vinyl chloride) (PVC-U) profiles with light coloured surfaces intended to be used for the fabrication of windows and doors.
It is applicable to PVC-U profiles with the colorimetric co-ordinates measured on the visible surfaces, as follows:
-   L *  82 (chromaticity co-ordinate Y  60)
-   -2,5  a*  5
-   -5  b*  15
when determined in accordance to ISO 7724-1 [1], ISO 7724-2 [2] and ISO 7724-3 [3], using CIE Standard illuminant D65 including specular reflectance and measuring condition 8/d or d/8 (without gloss trap for both), the angle of observation being selected as either 2° or 10° according to ISO 7724 1.

Profile aus weichmacherfreiem Polyvinylchlorid (PVC-U) zur Herstellung von Fenstern und Türen - Klassifizierung, Anforderungen und Prüfverfahren - Teil 1: Nicht beschichtete PVC-U Profile mit hellen Oberflächen

Diese Europäische Norm legt die Klassifizierungen, Anforderungen an und Prüfverfahren für nicht beschichtete, helle Profile aus weichmacherfreiem Polyvinylchlorid (PVC U) zur Herstellung von Fenstern und Türen fest.
Diese Norm gilt für PVC U-Profile mit den folgenden Farbmaßzahlen, die auf sichtbaren Oberflächen gemessen wurden:
   L*  82 (Farbwertkoordinate Y  60),
   2,5  a*  5,
   5  b*  15,
bei Bestimmung nach ISO 7724 1, ISO 7724 2 und ISO 7724 3 unter Anwendung der CIE-Normlichtart D65 unter Glanzeinschluss und der Messbedingung 8/d oder d/8 (in beiden Fällen ohne Glanzfalle); der gewählte Betrachtungswinkel beträgt nach ISO 7724 1 entweder 2° oder 10°.

Profilés de poly(chlorure de vinyle) non plastifié (PVC-U) pour la fabrication des fenêtres et des portes — Classification, exigences et méthodes d’essai - Partie 1: Profilés en PVC-U non revêtus avec des faces de teinte claire

Le prEN 12608 1 spécifie la classification, les exigences et les méthodes d’essai des profilés de poly(chlorure de vinyle) non plastifié (PVC U) non revêtus avec des faces de teinte claire destinés à être utilisés pour la fabrication des fenêtres et des portes.
Il s’applique aux profilés en PVC U dont les coordonnées colorimétriques mesurées sur les surfaces visibles sont les suivantes :
   L*  82 (coordonnée de chromaticité Y  60),
   –2,5  a*  5,
   –5  b*  15,
lors d’une détermination conformément à l’ISO 7724 1, l’ISO 7724 2 et l’ISO 7724 3 au moyen de l’illuminant normalisé D65 de la CIE, comprenant la réflexion spéculaire et la condition de mesure 8/d ou d/8 (sans piège à brillant dans les deux cas), l’angle d’observation choisi étant de 2° ou de 10° conformément à l’ISO 7724 1.

Profili iz trdega polivinilklorida (PVC-U) za izdelavo oken in vrat - Razvrščanje, zahteve in preskusne metode - 1. del: Neprevlečeni PVC-U profili s svetlo površino

Ta del standarda EN 12608 določa razvrščanje, zahteve in preskusne metode za neprevlečene profile iz trdega polivinilklorida (PVC-U) s svetlo površino, ki so namenjeni za uporabo pri izdelavi oken in vrat. Uporablja se za profile iz trdega polivinilklorida s kolorimetričnimi koordinatami, izmerjenimi na vidni površini, kot je opisano v nadaljevanju: – L * 82 (kromatska koordinata Y 60) – –2,5 a* 5 – –5 b* 15 v skladu s standardi ISO 7724-1 [1], ISO 7724-2 [2] in ISO 7724-3 [3] ob uporabi standarda za vrsto svetlobe CIE D65, vključno z refleksijsko odbojnostjo in pogojem meritve 8/d ali d/8 (brez zadrževanja sijaja pri obeh), pri čemer je izbran 2-stopinjski ali 10-stopinjski vidni kot v skladu s standardom ISO 7724 1.

General Information

Status
Withdrawn
Public Enquiry End Date
09-Mar-2014
Publication Date
05-Apr-2016
Withdrawal Date
31-Aug-2020
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
27-Aug-2020
Due Date
19-Sep-2020
Completion Date
01-Sep-2020

Relations

Buy Standard

Standard
EN 12608-1:2016
English language
24 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Profile aus weichmacherfreiem Polyvinylchlorid (PVC-U) zur Herstellung von Fenstern und Türen - Klassifizierung, Anforderungen und Prüfverfahren - Teil 1: Nicht beschichtete PVC-U Profile mit hellen OberflächenProfilés de poly(chlorure de vinyle) non plastifié (PVC-U) pour la fabrication des fenêtres et des portes — Classification, exigences et méthodes d’essai - Partie 1: Profilés en PVC-U non revêtus avec des faces de teinte claireUnplasticized poly(vinyl chloride) (PVC-U) profiles for the fabrication of windows and doors - Classification, requirements and test methods - Part 1: Non-coated PVC-U profiles with light coloured surfaces91.060.50Vrata in oknaDoors and windows83.140.99Drugi izdelki iz gume in polimernih materialovOther rubber and plastics productsICS:Ta slovenski standard je istoveten z:EN 12608-1:2016SIST EN 12608-1:2016en01-maj-2016SIST EN 12608-1:2016SLOVENSKI
STANDARDSIST EN 12608:20031DGRPHãþD



SIST EN 12608-1:2016



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 12608-1
March
t r s x ICS
z uä s v rä { {â
{ sä r x rä w r Supersedes EN
s t x r zã t r r uEnglish Version
fabrication of windows and doors æ Classificationá requirements and test methods æ Part
sã Nonæcoated PVCæU profiles with light coloured surfaces Classificationá exigences et méthodes d 5essai æ Partie
sã Profilés en PVCæU non revêtus avec des faces de teinte claire Klassifizierungá Anforderungen und Prüfverfahren æ Teil
sã Nicht beschichtete PVCæU Profile mit hellen Oberflächen This European Standard was approved by CEN on
s w January
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey andUnited Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s x CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s t x r zæ sã t r s x ESIST EN 12608-1:2016



EN 12608-1:2016 (E) 2 Contents Page
European foreword . 4 1 Scope . 6 2 Normative references . 6 3 Terms and definitions . 7 3.1 General . 7 3.2 Profile definitions . 7 3.3 Geometrical definitions . 8 3.4 Material definitions . 9 4 Classifications . 10 4.1 General . 10 4.2 Classification of climatic zones. 10 4.3 Classification of main profiles according to the resistance to impact by falling mass . 11 4.4 Classification of main profiles according to the wall thickness of the external walls . 11 5 Requirements . 13 5.1 Material . 13 5.1.1 UV resistant virgin material . 13 5.1.2 Non-UV resistant virgin material . 13 5.1.3 Reprocessed, recycled materials and non-UV resistant virgin materials . 13 5.2 Appearance . 14 5.3 Dimensions and tolerances . 14 5.3.1 General . 14 5.3.2 Nominal shape . 14 5.3.3 Wall thickness of main profiles . 14 5.3.4 Tolerances on other dimensions . 15 5.3.5 Deviation from straightness of the main profiles . 15 5.4 Linear weight of the main profiles . 15 5.5 Heat reversion . 15 5.5.1 Main profile . 15 5.5.2 Auxiliary profiles . 15 5.6 Resistance to impact of main profiles by falling mass . 16 5.7 Behaviour after heating at 150 °C . 16 5.8 Charpy impact resistance of main profile . 16 5.9 Resistance to weathering . 16 5.9.1 Exposure procedure . 16 5.9.2 Impact strength after artificial weathering of main profiles . 17 5.9.3 Colour fastness . 17 5.10 Strength of welded corners and T-joints of main profiles . 17 5.10.1 Test method . 17 5.10.2 Tensile bending test . 17 5.10.3 Compression bending test . 17 6 Test methods . 17 6.1 Determination of the appearance . 17 6.2 Determination of dimensions . 18 6.2.1 Measuring devices . 18 SIST EN 12608-1:2016



EN 12608-1:2016 (E) 3 6.2.2 Test specimen . 18 6.2.3 Conditioning . 18 6.2.4 Procedure . 18 6.3 Determination of the linear weight of the profile . 18 6.3.1 Apparatus . 18 6.3.2 Test specimen . 18 6.3.3 Conditioning . 18 6.3.4 Procedure . 18 6.4 Determination of the thickness of a coextruded layer . 19 6.5 Determination of colorimetric co-ordinates . 19 6.6 Permissible tolerances on standard colours . 19 7 Marking . 19 7.1 Main profiles . 19 7.2 Auxiliary profiles . 20 Annex A (normative)
Material characteristics, preparation of samples and requirements . 21 A.1 General . 21 A.2 Test specimens . 21 A.3 Preparation of pressed plates . 21 A.4 Material characteristics . 21 A.4.1 Vicat softening temperature . 21 A.4.2 Flexural modulus of elasticity . 22 A.4.3 Tensile impact strength . 22 A.5 Test report . 22 Annex B (normative)
Calculation method for the determination of the radiant exposure and exposure time to be used for artificial weathering. 23 B.1 General . 23 B.2 Calculation. 23
SIST EN 12608-1:2016



EN 12608-1:2016 (E) 4 European foreword This document (EN 12608-1:2016) has been prepared by Technical Committee CEN/TC 33 “Doors, windows, shutters, building hardware and curtain walling”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2016, and conflicting national standards shall be withdrawn at the latest by March 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 12608:2003. The major modifications to the previous edition are: — Change in structure of definitions (general, profile, geometrical and material); — Review of definitions of own reprocessed (previously reprocessable) material (3.4.5) and external reprocessed (previously reprocessable) material (3.4.6); — Including a new material (non-UV resistant virgin material); — Review of Table 1, which defines the classification of climatic zones in Europe; (correction of a mistake in EN12608:2003); — Addition of a class (no performance determined) for the classification of main profiles according to the resistance to impact by falling mass (Table 2); — Complete review of 5.1, giving the requirements for materials, establishing the distinction between UV resistant virgin material (5.1.1), non UV-resistant virgin material (5.1.2) and reprocessed (previously reprocessable), recycled (previously recyclable) materials and non-UV resistant virgin materials (5.1.3) with the addition of Table 4 which defines the uses allowed according to the type of material); — Review of the test of Charpy impact resistance of main profiles (5.8); Introduction of dependence on classes of wall thickness; — Review of the methods to determine the colorimetric co-ordinates (6.5); — Addition of new subclause 6.4 for the determination of the thickness of a co-extruded layer; — Addition of a requirement for individual values for the Vicat softening temperature (A.4.1); — Addition of a requirement for individual values for the flexural modulus of elasticity (A.4.2); — Addition of a requirement for individual values for the tensile impact strength (A.4.3); — Deletion of the Charpy impact resistance from Annex A (material characteristics); — Editorial review of the whole document and updating of normative references. SIST EN 12608-1:2016



EN 12608-1:2016 (E) 5 EN 12608, Unplasticized poly(vinyl chloride) (PVC-U) profiles for the fabrication of windows and doors - Classification, requirements and test methods consists of the following parts: — Part 1: Non-coated PVC-U profiles with light coloured surfaces — Parts 2: PVC-U profiles with laminated foils (in preparation) — Parts 3: PVC-U profiles with coextruded coloured top-layer (in preparation) — Parts 4: PVC-U profiles with lacquered-coating (in preparation) According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 12608-1:2016



EN 12608-1:2016 (E) 6 1 Scope This European Standard specifies the classifications, requirements and test methods for non-coated unplasticized poly(vinyl chloride) (PVC-U) profiles with light coloured surfaces intended to be used for the fabrication of windows and doors. It is applicable to PVC-U profiles with the colorimetric co-ordinates measured on the visible surfaces, as follows: — L* - — – tá w
¶ a — – w
¶ b NOTE 1 For editorial reasons in this document the term "window" is used for window/door. NOTE 2 Profiles made from PVC-U materials with reinforcements (e.g. glass fibres) are not part of this scope. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 477, Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors - Determination of the resistance to impact of main profiles by falling mass EN 478, Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors - Appearance after exposure at 150 °C - Test method EN 479, Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors - Determination of heat reversion EN 513, Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors - Determination of the resistance to artificial weathering EN 514, Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors - Determination of the strength of welded corners and T-joints EN ISO 105-A01:2010, Textiles - Tests for colour fastness - Part A01: General principles of testing (ISO 105-A01:2010) EN ISO 178, Plastics - Determination of flexural properties (ISO 178) EN ISO 179-1, Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1) EN ISO 306, Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO 306) EN ISO 1163-2:1999, Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO 1163-2:1995) SIST EN 12608-1:2016



EN 12608-1:2016 (E) 7 EN ISO 8256, Plastics - Determination of tensile-impact strength (ISO 8256) EN ISO 11664-1, Colorimetry - Part 1: CIE standard colorimetric observers (ISO 11664-1) EN ISO 11664-2, Colorimetry - Part 2: CIE standard illuminants (ISO 11664-2) EN ISO 11664-4, Colorimetry - Part 4: CIE 1976 L*a*b* Colour space (ISO 11664-4) EN 20105-A02, Textiles - Tests for colour fastness - Part A02: Grey scale for assessing change in colour (ISO 105-A02) ISO 18314-1, Analytical colorimetry — Part 1: Practical colour measurement 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 General 3.1.1 durability ability of a profile to maintain satisfactory properties in a window over an estimated working life which is at least the economically reasonable working life of the window installed in a building (works) Note 1 to entry: The indications given on the working life of a product cannot be interpreted as a guarantee given by the producer, but are regarded only as a means for choosing the right products in relation to the expected economically reasonable working life of the works. 3.2 Profile definitions 3.2.1 profile product produced by extrusion 3.2.2 non-coated profile profile without any surface treatment and without non-PVC-U coextruded layer(s) EXAMPLE Profiles without laminated foils or painted surfaces. 3.2.3 main profile profile, which defines the structure of the window 3.2.4 auxiliary profile profile intended to be used for the fabrication of a window which is not a main profile Note 1 to entry: Main and auxiliary profiles can be different according to the window construction techniques in the individual countries. 3.2.5 external wall (of a main profile) wall of a main profile corresponding to its sight and non-sight surfaces SIST EN 12608-1:2016



EN 12608-1:2016 (E) 8 3.2.6 sight surface surface of a profile exposed to view when the installed window is closed Note 1 to entry: See Figure 1.
Figure 1 — Sight surfaces of three typical main profiles 3.2.7 visible surface any surface or parts of surface of a profile which can be exposed to UV radiation after installation of the window, open or closed 3.2.8 coextruded profile profile produced by using more than one extruder with different PVC-U materials according to 3.4 in one production process without mixing them 3.3 Geometrical definitions 3.3.1 nominal profile shape shape and dimensions of a profile, as specified by the manufacturer 3.3.2 deviation from straightness deviation of the longitudinal axis of a profile from the straight line 3.3.3 depth (of a profile) d dimension, measured at right angles to the glazing plane, between the front and back face surfaces of a profile Note 1 to entry: See “d” in Figure 2. SIST EN 12608-1:2016



EN 12608-1:2016 (E) 9 3.3.4 overall width (of a profile) w largest dimension, measured in the direction of the glazing plane, perpendicular to the longitudinal axis of a profile Note 1 to entry: See “w” in Figure 2.
Key d depth of a profile w overall width of a profile Figure 2 — Cross-section of a typical profile 3.4 Material definitions 3.4.1 material PVC-U compound in a form of granules or powder for the production of PVC-U profiles intended to be used for the fabrication of a window 3.4.2 defined formulation formulation which is a specified composition of polymer, additives and pigments 3.4.3 virgin material material of a defined formulation, which has not been used or processed other than required for its manufacture and to which no reprocessed or recycled material has been added 3.4.4 non-UV resistant virgin material material according to 3.4.3 but not necessarily satisfying the requirements of the resistance to weathering Note 1 to entry: See 5.9. SIST EN 12608-1:2016



EN 12608-1:2016 (E) 10 3.4.5 own reprocessed material material prepared from defined formulations, free of degradation, prepared from pre-consumer PVC-U profiles in conformance with this part of EN 12608, including mis-measured/unused windows and off-cuts, from window assembling manufacturers, that will be reprocessed by the same manufacturer from which it was previously extruded Note 1 to entry: Profiles produced with an own reprocessed material of the same formulation show the same performance as those made of virgin material. 3.4.6 External reprocessed material 3.4.6.1 ERMa material whose characteristics (excluding colour) are in conformance with this part of EN 12608, prepared from pre-consumer PVC-U profiles including off-cuts, which has been originally produced by other manufacturers than those carrying out the reprocessing 3.4.6.2 ERMb material prepared from pre-consumer PVC-U profiles, regardless of where they were originally manufactured (e.g. glazing beads with PVC coextrusion/gaskets, coated profiles) 3.4.7 recycled material 3.4.7.1 RMa material prepared from post-consumer PVC-U product, regardless of where they were originally manufactured (e.g. glazing beads with PVC coextrusion/gaskets, coated profiles) 3.4.7.2 RMb any material which is not defined in 3.4.3 to 3.4.7.1 4 Classifications 4.1 General In EN 12608-1 various aspects of performance are classified. The selection of appropriate classes necessary to fulfil national requirements may be given in a national foreword of EN 12608-1. 4.2 Classification of climatic zones For the purposes of this document, geographical Europe is divided in two climatic zones M (moderate climate) and S (severe climate) as defined in Table 1. These climatic zones do not cover climates outside of geographical Europe. SIST EN 12608-1:2016



EN 12608-1:2016 (E) 11 Table 1 — Classification of climatic zones in Europe Class Moderate climate M Severe climate S Annual total solar radiant exposurea on horizontal surface < 5 GJ/m2 and 2 or Average temperaturea of the warmest month per year < 22 °C
·
t t
¹C a Values measured according the specifications of the World Meteorological Organisation (WMO). Profiles which are designed to be used in a severe climate (S) may also be used in a moderate climate (M). In those countries where the two climatic zones exists, care should be taken that profiles designed for a moderate climate (M) are not used in the severe climate (S). 4.3 Classification of main profiles according to the resistance to impact by falling mass For the resistance to impact by falling mass at –10 °C, the main profiles shall be classified according to Table 2. Table 2 — Classification of main profiles according to the resistance to impact by falling mass Class 0 I II Falling mass (g) NPD 1 000 1 000 Falling height (mm) NPD 1 000 1 500 NPD: No Performance Determined. NOTE This property is assessed to ensure the extrusion process is carried out correctly. It is recommended that class 0 is applied only when the profile geometry dictates that this test cannot be performed. 4.4 Classification of main profiles according to the wall thickness of the external walls For the wall thickness of the external walls, the main profiles shall be classified according to Table 3. Figure 3 shows the areas of two typical profiles where the wall thicknesses of external walls shall satisfy the requirements given in Table 3. SIST EN 12608-1:2016



EN 12608-1:2016 (E) 12
Detail measuring instrument Detail measuring length Areas to be taken into consideration are marked as shaded areas. Figure 3 — Areas of typical profiles with required wall thicknesses Table 3 — Classification of main profiles according to wall thickness Class A mm B mm C Sight surface
·
tá z
·
tá w No requirement Non-sight surface
·
tá w
·
tá r No requirement NOTE
The classification of main profiles according to the wall thickness is intended to represent the wide variations in profile and window design for the various systems which are in use in Europe. It is not intended to imply differences in profile quality or in the performance of windows provided that the relevant performance requirements for both profiles and windows are met. In order to be classified for either class A or B both minimum requirements for the wall thickness shall be fulfilled. Sight surfaces of typical profiles are shown in Figure 1. SIST EN 12608-1:2016



EN 12608-1:2016 (E) 13 5 Requirements 5.1 Material 5.1.1 UV resistant virgin material The UV resistant virgin material shall comply with the requirements given in Annex A and 5.9. 5.1.2 Non-UV resistant virgin material It is permitted to use a non-UV resistant virgin material when the coextruded visible surfaces of the profile are made from a UV resistant virgin material or an own reprocessed material. The non-UV resistant virgin material shall comply with the requirements given in Annex A. 5.1.3 Reprocessed, recycled materials and non-UV resistant virgin materials If the material used is not a UV resistant virgin material according to 5.1.1, the requirements of this document apply together with the following: a) the use of reprocessed, recycled and non UV resistant materials shall conform to Table 4; b) materials of types ERMa, ERMb or RMa may be used after any necessary re-stabilization and/or addition of additives (e.g. modifiers, pigments, lubricants) for the core of a profile, where any visible surfaces of the window are completely covered by coextrusion with a virgin material or an own reprocessed material; c) for sight surfaces, the minimum value of thickness of the coextruded surface layer shall be 0,5 mm; d) for non-sight visible surfaces the minimum thickness of the coextruded surface layer shall be 0,2 mm; e) no requirement for minimum thickness of the coextruded surface layer at the bottom of grooves with an open width

w mmä Table 4 — Use of reprocessed, recycled and non UV resistant virgin materials Application Material Own reprocessed material Non UV-resistant virgin material ERMa ERMb RMa RMb Monoextrusion or coextrusion of a layer of any visible surface Yes No No No No No Non-visible surface and material covered by coextrusion Yes Yes Yes Yesa Yesa No a Materials as defined in 3.4 shall comply with the following requirement: A profile produced with this material shall fulfi
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.